PROVN OF TWO WHEELER PARKING SHED WITH HARD STANDING NEAR BLDG NO P-343, PROVN OF 01 X TOILET, BATHROOM, WASH BASIN, 02 X URINALS NEAR BLDG NO P-33/35-A5 OF 6 GARH RIF AND CONSTR OF TOILET FOR APS (PRE-PRIMARY WING) AT PMS UNDER GE (A) TRIVANDRUM

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed.

Material and labour for Plain Cement Concrete 1:4:8, type D2 (40mm graded stone aggregate) as in, foundations filling and mass concrete complete all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:4) complete all as specified and directed.

M&L for 40 mm thick damp proof course in cement concrete 1:2:4, type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore using broken stone or boulders of gauge exceeding 63 mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8, Type D2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over 20 mm thick screed bed in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4, Type B0 (using 12.50 mm graded stone aggregate) as in sub base of floor, levelling course, sunken floor, etc complete all as specified and directed.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 450x 300x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10 mm thick backing on stone/ brick masonry surfaces in cement mortar (1:4) complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in plinth protection/ path laid to slope 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster in cement mortar 1:6 on fair faces of brick work/ PCC solid block masonry/ concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering in two layers 10mm thick with cement mortar (1:6) as under coat and 5 mm thick with cement mortar (1:4) as finishing coat, finishing coat mixed with water proofing compound @ 3% by the weight of cement on fair faces of brick work even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for preparing new plastered wall surfaces, applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Supply only integral water proofing compound all as specified and as directed.

S&F 40mm dia PVC waste pipe 60 cm long with union for urinal complete all as specified and directed.

S&F 32mm dia PVC waste pipe 80 cm long with union for WHB complete all as specified and directed.

S&F PVC connection 15mm dia 600 mm long with 2 Nos brass check nuts with washers etc complete all as specified and directed.

S&F counter top vitreous China wash basin of superior specification, white, flat back of size 570 x 420 x 195 mm complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

M&L for PVC (SWR) gully trap 125/ 110 mm dia, setting and jointing with solvent cement including dismantling existing one complete all as specified and directed.

S&F polished edge 5-6 mm thick glass mirror silvered to give maximum reflection, free from tarnishing, discolouration, scratches and other visible defects of required height fixed to plastered wall/ board with suitable fixing material complete all as specified and directed.

S&F pillar taps of size 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts screwed for iron pipe complete all as specified and directed.

S&F bib tap, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for 15mm bore dia iron pipe/ PVC pipe or for brass ferrule complete all as specified and directed.

S&F 15mm bore dia stop valve/ angle cock, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm dia iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore dia stop cock/ angle cock, cast copper alloy, fancy type, chromium plated, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm dia iron pipe or for unions and fixed complete all as specified and directed.

S&F Tubular towel rail, aluminium anodised, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F shower rose, brass, chromium plated 125mm size with or without swivel joints, fixed to steel pipe or union complete all as specified and directed.

S&F PVC ventilator fixed type with solid frame of size 70mm x 45mm including louvers, frosted glass 3mm thickness, including MS guard bars of 10mm dia spacing 150 mm C/C and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with PVC beading including synthetic enamel painting to steel surfaces. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size complete all as specified and directed.

S&F 15 mm bore unplasticised PVC pipes ASTM 1784 Sch 80 Class III with necessary fittings fixed complete to walls, ceilings or in floors etc., any type of pipe, including taking down old PVC pipes complete all as specified and directed.

S&F 20 mm bore unplasticised PVC pipes ASTM 1784 Sch 80 Class III with necessary fittings fixed complete to walls, ceilings or in floors etc., any type of pipe, including taking down old PVC pipes complete all as specified and directed.

S&F 25 mm bore unplasticised PVC pipes ASTM 1784 Sch 80 Class III with necessary fittings fixed complete to walls, ceilings or in floors etc., any type of pipe, including taking down old PVC pipes complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including connecting inlet and outlet pipe lines complete all as specified and directed.

S&F vitreous China wash down single piece water closet pan 360 x 640 x 685 mm with soft close cover, hinges, dual flushing cistern having superior specification 'P' or 'S' trap (Pedestal pattern), white, including fixing bolts, flushing cistern, flush pipe complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore dia. PVC (SWR) bend any radius complete all as specified and directed.

S&F 110mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) floor trap, outlet 75 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for salt-glazed stoneware gully traps size 150 x 150 mm, square or round mouthed, tvpe 'P' setting and jointing to drains with cement mortar 1:1 complete all as specified and directed.

S&F 75 mm bore dia. PVC (SWR) bend any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, fixed to walls complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, double socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.

Cutting into existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, smooth finished, and reforming benching as required for 100 mm internal dia. of pipe complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 75 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 200 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 25 mm outer dia CPVC ball valve complete all as specified and directed.

S&F TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

S&F TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Use & waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for falt, fair finished surfaces of concrete complete all as specified and directed.

M&L for providing reinforced cement concrete type B-1, 1:2:4 (20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished surfaces of concrete complete all as specified and directed.

M&L for providing reinforced cement concrete type B-1, 1:2:4 (20 mm graded aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for 5mm thick rendering in cement mortar 1:3 on fair faces of concrete surfaces as in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying three coats of white wash including preparation of new plastered surfaces on ceiling complete all as specified and directed.

M&L for 25 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded stone aggregate over RCC roof as levelling course complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster on fair faces of brick work/ concrete surfaces in cement mortar 1:3, mixed with water proofing compound @ 3% by the weight of cement, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for water proofing treatment over RCC slab by applying oil bound bitumen primer @ 0.27 Ltr/ Sqm, provide and lay 4 mm thick APP modified water proofing membrane thickness and weighing not less than 4.50 Kg/ Sqm, reinforced with non-woven polyester, matt black finished (weighing not less than 160 gms/ sqm) having softening point not less than 140 degree Celsius, longitudinal tensile strength not less than 650 N/ 5cm, tearing strength of 180 N, a static puncture resistance of 180, keeping minimum 10 cm side lap and 15 cm end laps and apply by torch application over a coat of blown grade hot bitumin grade VG-10 conforming to IS 702 heated to a working temperature of 180 centigrade and applied @ 1.20 Kg/ Sqm of the surface area and finishing the top surface with solar reflective bituminous aluminum paint applied @ 0.10 Kg /sqm complete all as specified by manufacture's instructions and Engr-in-charge.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M&L for 18 mm to 20 mm thick prelaminated HDF panels of interior grade type-II of approved shade for kitchen cabin/ wardrobe/ wall panelling fixing with necessary fitting like keku fitting, spring clip, hanger plate, modular hinge/ clip, push fix or stud fitting as per manufacturers instructions complete all as specified and directed.

S&F stainless steel full overlay modular hinge of required size as per direction of Engr-in-charge complete all as specified and directed.

S&F soap dish, vitreous China white, approximate size 160x 160x90mm fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube in chrome finish and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/ loose soil, each not exceeding 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

Material and labour for Plain Cement Concrete 1:3:6, type C2 (40mm graded stone aggregate) as in, foundations filling and mass concrete complete all as specified and directed.

S&F mild steel works framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5cm long and 11 to 15 mm dia of neck complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide Zinc Chrome primer complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet (Trepezium or tile pattern) 0.50mm thick (with 0.45 mm BMT) of any colour having tensile strength of 550 Mpa (Pitch of corrugation shall be 200 mm to 250 mm and crest shall be 28 mm to 32 mm) as in roof covering/ cladding to wall, fixed with self-tapping screws/ J-hooks complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L use and waste of timber as in formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for flat, rough finished surfaces of concrete complete all as specified and directed

M&L for providing reinforced cement concrete type B-1, 1:2:4 (20 mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L for use and waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions in square, rectangular and polygonal shape to rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions in square, rectangular and polygonal shape to fair finished surfaces of concrete complete all as specified and directed.

M&L for providing reinforced cement concrete type B-1, 1:2:4 (20 mm graded aggregate) Columns, pillars, piers, posts and struts complete all as specified and directed

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat fair finished surfaces of concrete complete all as specified and directed.

M&L for providing precast cement concrete solid building blocks or slabs 10cm thick with PCC (1:3:6), type C1, using 20mm graded stone aggregate (with plain or interlocking joints as directed) setting in mortar (1:4), complete, in walls complete all as specified and directed.

M&L for hardcore using broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8, Type D2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster in cement mortar 1:4 on fair faces of brick work/ PCC solid block masonry/ concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in cement mortar 1:4 on fair faces of brick work/ PCC solid block masonry/ concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

S&F PVC connection 15mm dia 450 mm long with 2 Nos brass check nuts with washers etc complete all as specified and directed.

S&F Vitreous China wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand, waste pipe and connected fittings complete all as specified and directed.

S&F vitreous China female urinal pot size 350x430x100 mm premium designer luxurious ceramic floor mount urinal pot for ladies/ girls toilet/ washroom including fixing plugs, pointing around urinal back in cement ; bedding in cement mortar 1:2 complete all as specified and directed.

S&F brass chromium plated two way bib cock with wall flange complete all as specified and directed. (Make: Jaguar cat No. LYR-CHR-38041)

S&F 20mm bore dia stop valve/ angle cock, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 20 mm dia iron pipe or for unions and fixed complete all as specified and directed.

S&F 25mm bore dia stop valve/ angle cock, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 25 mm dia iron pipe or for unions and fixed complete all as specified and directed.

S&F 40 mm bore unplasticised PVC pipes ASTM 1784 Sch 80 Class III with necessary fittings fixed complete to walls, ceilings or in floors etc., any type of pipe, including taking down old PVC pipes complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white, including fixing bolt, seat cover (excluding flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage etc and 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and including 32 mm bore PVC flush pipe complete all as specified and directed.

S&F vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor and 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and including 32 mm bore PVC flush pipe complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, double socketed, in any length with rubber ring joints or jointing with solvent cement, fixed to walls complete all as specified and directed.

S&F 75mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) multi floor trap, outlet 75 mm dia, with grating including jointing with solvent cement complete all as specified and directed.

M&L for PVC (SWR) gully trap 150 mm dia, setting and jointing with solvent cement including dismantling existing one complete all as specified and directed.

S&F 75 mm bore dia. PVC (SWR) vent cowl complete all as specified and directed.

S&F 100 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 20 mm bore dia of pipe complete all as specified and directed.

S&F stainless steel wall mounted decorative type cloth hanger and hooks rail with 4 hooks of size 20 cm x 4 cm x 1.49 mm thick of approved quality, rust resistant, including screws/ brackets complete all as specified and directed.

S&F toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F heavy duty grab bar for bathroom toilet handrails safety rail made of aluminium alloy thicken material for lasting performance, stainless steel screws for corrosion resistance for senior citizen/ special disabled person (60x20x6 cm) moveable 90 degree (horizontally and vertically), weight capacity 105 Kg complete all as specified and directed.

S&F Vitreous china urinal partition white of size 310x700 mm, terminating about 40cm above floor line complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for coloured and polished chequered cement concrete tiles 40cm x 40cm x 25mm thick, set, jointed and pointed in neat cement slurry as in floors with grey pigment cement and pigments, including over 15 mm thick screed bed in cement mortar (1:6) complete all specified and directed.

M&L for providing, cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

S&F 150/ 160 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.

M&L for concrete bed to drain pipes 150/ 160 mm bore dia including forming cradles by using PCC (1:3:6), type C2 using 40 mm graded aggregate including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for providing plain cement concrete type B-1, 1:2:4 (20 mm graded aggregate) in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in manhole/ Gully trap cover slab set in CM 1:6 including use and waste of necessary form work complete all as specified and directed.

S&F 20 users LDPE septic tank designed to carry sewage and sullage water including excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection, etc. complete all as specified and directed.

M&L for soakage well excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M 25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M25/ SFRC cover, inter connecting pipes of RCC/ DWC complete filled with bricks bats of size 1.80 mtr dia and 3.00 mtr effective depth complete all as specified and directed.

S&F 20mm bore dia stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 20 mm dia iron pipe or for unions and fixed complete all as specified and directed.

M&L for bricks; common burnt clay building bricks, sub-class ‘B’ designation 75, laid flat over the soil cushioning to UG cable complete all as specified and directed.

M&L for 40 mm bore GI tubing light grade with fittings laid for protection of cable under road crossing, fixed to walls or pole complete all as specified and directed.

M&L for point wiring complete for one light point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor partly concealed in wall through PVC conduit and conduit accessories and partly surface on ceiling/ roof through PVC conduit and accessories of suitable size with modular metal flush boxes of suitable size & modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, multistranded single core green colour copper conductor for earth continuity connected to earth dolly all as specified and directed Note: Cost of modular metal flush boxes concealed in wall with suitable white cover plate for mounting switches/ sockets, regulators, bell push etc and cost of cutting chases & making good to disturbed surface with cement mortar, if required any shall be deemed to be included in the quoted rate.

All as per item No. 124.00 here in before but for one fan point controlled by one way switch and regulator complete all as specified and directed.

All as per item No. 124.00 here in before but for One 3 Pin, 5 Amps socket outlet on same board with other switches/ sockets complete all as specified and directed.

All as per SI item No. 124.00 here-in-before, but for one switch socket outlet, 3 pin 16 Amp on independent board with 2.50 Sqmm FRLS cable and 2.50 sqmm cable earth continuity wire complete all as specified and directed.

S&F modular switch 1 way 6A, 1 module, 240 Volts complete all as specified and directed.

S&F modular switch 1 way 16A, 1 module, 240 Volts complete all as specified and directed.

S&F modular socket, 6A - 2/3 pin combined 2 module, flush type complete all as specified and directed.

S&F modular socket 6A/16A - 2/3 pin combined 2 module, flush type complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and directed.

S&F ceiling rose, 3 terminals PVC/ polycarbonate, isolated body complete all as specified and directed.

M&L for distribution board, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 4 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urethane (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCB TP/SPN/SP etc, complete all as specified and directed.

S&F MCB single pole 5 to 32 Amps current carrying capacity, 240 volt rating, 10 KA, C curve with IP-20 protected terminals including contact indication window, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., complete with connection, testing and commissioning complete all as specified and directed.

S&F MCB SPN 40 Amps current carrying capacity, 240 volt rating, 10 KA, C curve with IP-20 protected terminals including contact indication window, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., complete with connection, testing and commissioning complete all as specified and directed.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below normal ground level, connected to galvanised earth lead of GI wire of size 4mm dia by means of GI bolts, nuts, check nuts and washers of the earth and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm bore from earth plate to Panel/ DBs and water pipe 20mm bore GI medium grade raised up to a level of 50cm above ground level with plug at top, earthing pit in PCC (1:3:6) type C-1 RCC pre-cast (1:2:4 type B-1) cover slab of 50 mm thick using 8.00mm dia CTD bars reinforcement both ways at 140 mm centre to centre with handle, 20 mm dia GI pipe medium grade for watering pipe, wire mesh, funnel and providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in any type of soil, returning, refilling and removing of surplus soil to a distance not exceeding 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 complete all as specified and directed.

Excavating in trenches in hard/ dense soil, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying of UG cable, pipe, pole, stay etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out complete all as specified and directed.

Returning and filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing surplus excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Material and labour for laying XLPE insulated, PVC innersheathed, extruded PVC outer sheathed, LT underground cable, armoured with glavanised wire, heavy duty electric cable with stranded aluminium conductor of cross-sectional area 2 core 10 sqmm, 1100 volts grade, as per IS 7098 (Part 1) 1988, laid in trench, fixed on wall/pole drawn through pipe etc including of provision of lugs & testing, including taking down old LT UG cable complete all as specified and directed.

Satheesh Kumar (BID ID -3498540)

JESWIN BUILDERS (BID ID -3504973)