Transit accommodation at T2

Amount

Buy-Back 199 Tr Screw Chiller

Buy-Back (ie minus) OLD AHU in T2

Buy-Back (ie minus) Old Fire Diesel Engine pump Dismantling and Buying Back

Buy-Back (ie minus) Old Electric pump its acessories Dismantling and Buying Back

Buy-Back (ie minus) Old Jockey pump its acessories Disamantling anf Buying Back

Description of Work / Item(s)

Amount

PRE CONSTRUCTION ANTI TERMITE TREATMENT Providing Pre-construction Anti-termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam and below the ground level as well as outside alround the building at plinth level etc as per the instructions of manufacturer and as directed by the Engineer-in-charge. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be and the application shall be diluted 1 part of chemical with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification. The work should be carried out by an approved and registered specialist pest control agency only. Tenderer to furnish the name of the proposed specialist firm. A 10 years post application guarantee against defects shall be furnished by the main Contractor. Note : Horizontal plan area at ground floor level of the building will be measured and paid. The chemical to be used for the treatment and concentration of the chemical solutions should be as laid down in IS - 6313 Part II.as complete with all respects complying with relevant. As per standards, specification and directed by the Engineer-in-charge.

EARTHWORK Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 M2 on plan) including getting out and disposal of excavated earth should lead upto 5 km and lift upto 1.50 m including bailing out of water if required. As per standards, specification and directed by the Engineer-in-charge. All kinds of soil:- (for I Lift 0 - 1.5m)

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 5km, As per standards, specification and directed by the Engineer-in-charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers,consolidating each deposited layer by ramming and watering, lead upto 5 Kms and lift upto 1.5 m. As per standards, specification, and directed by the Engineer-in-charge.

Excavating, supplying and filling of good latrite earth form oustide (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers in trenches( not ecxeeding 20cm), plinth, sides of foundation etc. complete. As per standards, specification and directed by the Engineer-in-charge.

Disposal of Earth/moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts,As per standards, specification and directed by the Engineer-in-charge.

Market Rate Providing and laying 600 micron guage polythene paper/Polythene sheet below Grade slab, PCC, Raft slab etc., to the required levels, including supply, loading and unloading, storing, transportation, laying, sealing of junctions and overlaps, all leads and lifts, etc.,complete.As per standards, specification and directed by the Engineer-in-charge.

Market Rate Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick),As per standards, specification and directed by the Engineer-in-charge.

Supplying and filling in plinth with M sand under floors( layers not exceeding 20cm), including watering,ramming, consolidating and dressing complete.

PLAIN CEMENT CONCRETE Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:4:8 (1 Cement : 4 coarse :8 sand derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) As per standards, specifications and directed by the Engineer-in-Charge. -1.Below Footing, 2. Below water, 3. Below Plinth beam, 4. Below Grade slab.

RCC - CONCRETE WORK - Below Plinth Level Providing and laying in position site batched design mix cement concrete of OPC 43 grade for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland Cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement for the following grades of concrete.As per standards, specification and directed by the Engineer-in-charge.- 1.Pile Cap/Footing, 2. Plinth beam, 3. Grade slab, 4. Circular Column.

RCC - CONCRETE WORK - Above Plinth Level Providing and laying in position site batched design mix cement concrete of OPC 43 grade for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland Cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement for the following grades of concrete.As per standards, specification and directed by the Engineer-in-charge. - 1.RCC Mullions,2. RCC Bands, 3.Water Body (Base slab & Walls), 4.Deck Slab , 5. Slab, 6. Circular Column, 7. Floor beam.

Extra for providing and fixing expanded metal mesh of size 20x60 mm and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm for encasing of rolled steel sections in beams, columns and grillages etc complete.As per standards, specification and directed by the Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.For Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level with Thermo-Mechanically Treated bars of grade Fe-500D or more.As per standards, specification and directed by the Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. For Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto & Above plinth level with Thermo-Mechanically Treated bars of grade Fe-500D or more.As per standards, specification and directed by the Engineer-in-charge.

Supplying, Drilling/Cleaning hole and injecting make, into a hole of 8mm dia & depth as per manufacturer specification and fixing rebars of the required diameter subsequently. The chemical should have successfull usage in wet/water saturated concrete/diamond cored holes. The chemical should have approval against creep & corrosion. Fixing methodology to be followed as per manufacturers guidelines. - Steel will be paid under separate subhead. Rate to Inclusive of Drilling in Blockwork / RCC / Rock etc. as per the requirement at all levels,complete., to the requirement of EIC. As per standards, specification and directed by the Engineer-in-charge. 8mm dia rebar.

Supplying, Drilling/Cleaning hole and injecting make, into a hole of 10mm dia & depth as per manufacturer specification and fixing rebars of the required diameter subsequently. The chemical should have successfull usage in wet/water saturated concrete/diamond cored holes. The chemical should have approval against creep & corrosion. Fixing methodology to be followed as per manufacturers guidelines. - Steel will be paid under separate subhead. Rate to Inclusive of Drilling in Blockwork / RCC / Rock etc. as per the requirement at all levels,complete., to the requirement of EIC. As per standards, specification and directed by the Engineer-in-charge. 10mm dia rebar.

Supplying, Drilling/Cleaning hole and injecting make, into a hole of 12mm dia & depth as per manufacturer specification and fixing rebars of the required diameter subsequently. The chemical should have successfull usage in wet/water saturated concrete/diamond cored holes. The chemical should have approval against creep & corrosion. Fixing methodology to be followed as per manufacturers guidelines. - Steel will be paid under separate subhead. Rate to Inclusive of Drilling in Blockwork / RCC / Rock etc. as per the requirement at all levels,complete., to the requirement of EIC. As per standards, specification and directed by the Engineer-in-charge. 12mm dia rebar.

Supplying, Drilling/Cleaning hole and injecting make, into a hole of 16mm dia & depth as per manufacturer specification and fixing rebars of the required diameter subsequently. The chemical should have successfull usage in wet/water saturated concrete/diamond cored holes. The chemical should have approval against creep & corrosion. Fixing methodology to be followed as per manufacturers guidelines. - Steel will be paid under separate subhead. Rate to Inclusive of Drilling in Blockwork / RCC / Rock etc. as per the requirement at all levels,complete., to the requirement of EIC. As per standards, specification and directed by the Engineer-in-charge. 16mm dia rebar.

Supplying, Drilling/Cleaning hole and injecting make, into a hole of 20mm dia & depth as per manufacturer specification and fixing rebars of the required diameter subsequently. The chemical should have successfull usage in wet/water saturated concrete/diamond cored holes. The chemical should have approval against creep & corrosion. Fixing methodology to be followed as per manufacturers guidelines. - Steel will be paid under separate subhead. Rate to Inclusive of Drilling in Blockwork / RCC / Rock etc. as per the requirement at all levels,complete., to the requirement of EIC. As per standards, specification and directed by the Engineer-in-charge. 20mm dia rebar.

Supplying, Drilling/Cleaning hole and injecting make, into a hole of 25mm dia & depth as per manufacturer specification and fixing rebars of the required diameter subsequently. The chemical should have successfull usage in wet/water saturated concrete/diamond cored holes. The chemical should have approval against creep & corrosion. Fixing methodology to be followed as per manufacturers guidelines. - Steel will be paid under separate subhead. Rate to Inclusive of Drilling in Blockwork / RCC / Rock etc. as per the requirement at all levels,complete., to the requirement of EIC. As per standards, specification and directed by the Engineer-in-charge. 25mm dia rebar.

Supplying, Drilling/Cleaning hole and injecting make, into a hole of 32mm dia & depth as per manufacturer specification and fixing rebars of the required diameter subsequently. The chemical should have successfull usage in wet/water saturated concrete/diamond cored holes. The chemical should have approval against creep & corrosion. Fixing methodology to be followed as per manufacturers guidelines. - Steel will be paid under separate subhead. Rate to Inclusive of Drilling in Blockwork / RCC / Rock etc. as per the requirement at all levels,complete., to the requirement of EIC. As per standards, specification and directed by the Engineer-in-charge. 32mm dia rebar.

Centering and shuttering including strutting, propping etc. and removal of form for concrete works. Foundations, footings, bases of columns, etc. for mass concrete. As per standards, specification and directed by the Engineer-in-charge. - Footing

Centering and shuttering including strutting, propping etc. and removal of form for concrete worksFoundations, footings, bases of columns, etc. for mass concrete. As per standards, specification and directed by the Engineer-in-charge.- Circular Column (at all Levels)

Centering and shuttering including strutting, propping etc. and removal of form for concrete works.Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.As per standards, specification and directed by the Engineer-in-charge.- Water Body (Base slab & Walls)

Centering and shuttering including strutting, propping etc. and removal of form for concrete worksSuspended floors,roofs,landings, balconies and access plat form.As per standards, specification and directed by the Engineer-in-charge. Slabs ( at all levels)

Centering and shuttering including strutting, propping etc. and removal of form for concrete worksLintels, beams, plinth beams, girders, bressumers and cantilevers.As per standards, specification and directed by the Engineer-in-charge. Plinth Beams, Rcc Mullions, RCC Bands, Floor Beams(At all levels).

MASONRY & PLASTERING WORKS Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. m/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. As per standards, specification and directed by the Engineer-in-charge.

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm/230mm/300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at every 1.2m with approved block laying polymer modified adhesive mortar all complete As per standards, specification and directed by the Engineer-in-charge.(The payment of RCC band and reinforcement shall be made for separately).

Providing and laying cement 12mm thick plaster on surfaces with fine sand including curing etc for internal walls including toilet area.As per standards, specification and directed by the Engineer-in-charge. 1:6 (1 cement : 6 fine sand)

Providing 6mm thick cement plaster on surfaces with fine sand including curing etc for ceiling.As per standards, specification and directed by the Engineer-in-charge. 1:3 (1 cement: 3 fine sand)

Providing 12 mm cement plaster finished with a floating coat of neat cement of mix for Wall /RCC surfaces.As per standards, specification and directed by the Engineer-in-charge. 1:4 (1 cement : 4 fine sand)

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.As per standards, specification and directed by the Engineer-in-charge.

Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.As per standards, specification and directed by the Engineer-in-charge.

Providing and mixing extra for water proofing material in cement plaster work in proportion recommended by the manufacturers.As per standards, specification and directed by the Engineer-in-charge.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete etc., As per standards, specification and directed by the Engineer-in-charge.

JOINERY WORKS Providing, fabricating and placing 44mm Single leaf Flush Door shutter of factory made finish, finished with (4.0 mm thick wood grain laminate + 42mm thick Flush Shutter + 4.0mm) in veneer of approved make on both sides including grooves,edge lipping all-round the shutter as per the detail drawings of the door shutter shall be fixed to Modular Door Frame of section 100MM X 45MM/25MM or as per manufacture's details of aluminium powder coated with all required rubber kit & connectors.anchor fastened in to the partition with suitable GI Screws over rough ground as per the detailed drawings. The door to be fixed in true line, level & plumb, fireproof solution, including all necessary hardware, finished with melamine polish, fittings, material, labour, lead, lift, scaffolding, protection till final finish & handover, complete in all respects.The rate inclusive of providing (a) 5knuckle , 4nos of Ball bearing butt hinges 100X75X3mm, SS304, SATIN FINISH, (b) Concealed Door Closer slide Arm channel - 01 no's ,(e) Door Stopper,(d) Concealed Drop seal below door - 01 no's etc., e) Smoke seal f) Door viewer etc as per drawing.As per standards, specification and directed by the Engineer-in-charge. For Single Leaf flush Door of size : 1100 mm x 2400 mm with Laminate finish on both the sides.Refer drawing AR/TD/205

Providing & Supplying of Heavy duty electronic mortise lockset with clutch mechanism and built-in contactless RFID reader and BLE(Bluetooth Low Energy) with long lever handle ,Guest RFID Mifare Cards , Access management software for RFID, Energy saving Switch with RF Mifare technology etc complete. As per standards, specification and directed by the Engineer-in-charge.Refer AR/TD/205.

Providing, fabricating and placing 44mm Single leaf Flush Door shutter of factory made finish, finished with (1.0 mm thick wood grain laminate + 42mm thick Flush Shutter + 1.0mm thick wood grain laminate)) in laminate on both sides including grooves,edge lipping all-round the shutter as per the detail drawings of the door shutter shall be fixed to Modular Door Frame of section of section 100MM X 45MM/25MM or as per manufacture's details of aluminium powder coated with all required rubber kit & connectors. Anchor fastened in to the partition with suitable GI Screws over rough ground as per the detailed drawings . The door to be fixed in true line, level & plumb, fireproof solution, including all necessary hardware, finished with melamine polish, fittings, material, labour, lead, lift, scaffolding, protection till final finish & handover, complete in all respects The rate inclusive of providing (a) 5knuckle , 4nos of Ball bearing butt hinges 100X75X3mm, SS304, SATIN FINISH, (b)Lever Handle with Lock , Strick plate & Euro Profile Cylinder with both side lock -01 no's, (c) Door Stopper, etc as per drawing. As per standards, specification and directed by the Engineer-in-charge.

Providing, fabricating and placing 44mm Single leaf Flush Door shutter of factoty made finish, finished with (1.0 mm thick wood grain laminate + 42mm thick Flush Shutter + 1.0mm thick wood grain laminate) in laminate on both sides including grooves,edge lipping all-round the shutter as per the detail drawings of the door shutter shall be fixed to Modular Door frame of section 100MM X 45MM/25MM or as per manufacture's details of aluminium powder coated with all required rubber kit & connectors.anchor fastened in to the partition with suitable GI Screws over rough ground as per the detailed drawings. The door to be fixed in true line, level & plumb, fireproof solution, including all necessary hardware, finished with melamine polish, fittings, material, labour, lead, lift, scaffolding, protection till final finish & handover, complete in all respects.The rate inclusive of providing (a) 5knuckle , 4nos of Ball bearing butt hinges 100X75X3mm, SS304, SATIN FINISH, (b)Lever Handle with Lock , Strick plate & Euro Profile Cylinder with both side knob -01 no's, (c) Door Stopper, etc as per drawing. As per standards, specification and directed by the Engineer-in-charge.as per drawing. AR/TD/205

Providing, fabricating and placing 44mm Single leaf Flush Door shutter of factoty made finish, finished with (1.0 mm thick wood grain laminate + 42mm thick Flush Shutter + 1.0mm thick wood grain laminate)) in laminate on both sides including grooves,edge lipping all-round the shutter as per the detail drawings of the door shutter shall be fixed to Modular Door frame of section 100MM X 45MM/25MM or as per manufacture's details of aluminium powder coated with all required rubber kit & connectors.anchor fastened in to the partition with suitable GI Screws over rough ground as per the detailed drawings. The door to be fixed in true line, level & plumb, fireproof solution, including all necessary hardware, finised with melamine polish, fittings, material, labor, lead, lift, scaffolding, protection till final finish & handover, complete in all respects. The rate inclusive of providing (a) 5knuckle , 4nos of Ball bearing butt hinges 100X75X3mm, SS304, SATIN FINISH, (b)Lever Handle with Lock , Strick plate & Euro Profile Cylinder with one side key & other side knob -01 nos, (c) Door Stopper, etc as per drawing.As per standards, specification and directed by the Engineer-in-charge.as per drawing. AR/TD/202

Providing, fabricating and placing 44mm Single leaf Flush Door shutter of factoty made finish, finished with (1.0mm thick wood grain laminate + 42mm thick Flush Shutter + 1.0mm thick wood grain laminate)) in laminate on both sides including grooves,edge lipping all-round the shutter as per the detail drawings of the door shutter shall be fixed to Modular door frame of section 100MM X 45MM/25MM or as per manufacture's details of aluminium powder coated with all required rubber kit & connectors.anchor fastened in to the partition with suitable GI Screws over rough ground as per the detailed drawings. The door to be fixed in true line, level & plumb, fireproof solution, including all necessary hardware, finised with melamine polish, fittings, material, labor, lead, lift, scaffolding, protection till final finish & handover, complete in all respects. The rate inclusive of providing (a) 5knuckle , 4nos of Ball bearing butt hinges 100X75X3mm, SS304, SATIN FINISH, (b)Lever Handle with Lock , Strick plate & Euro Profile Cylinder with both side lock -01 nos, (c) Door Stopper, etc as per drawing. As per standards, specification and directed by the Engineer-in-charge.Refer drawing AR/TD/220, AR/TD/222, AR/TD/223, AR/TD/224, AR/TD/225

Supply & Installation of Aluminium powder coated finish of Door Frames SYSTEM 100 ( frame) & SYSTEM 100 (Style) for door of size as specified below or as per drawing . Door Frame of section 100mm X 40mm with all required rubber kit & connectors as per the Manufacture Standard The rate to include Door Style using 100mm X 45mm as vertical profile & 100mm X 45mm as top & bottom profile, Using 10mm clear Laminated toughened glass approved brand like (with Glass mounting option), clear crystal edge polished glass fixing as per the required sizes and as per Design & drawings.the rate inclusive of material, Labour & wastage & Scaffolding Complete at all level. The rate inclusive of providing (a) 8nos of Ball bearing hinges 100X70X2mm, SS304, SATIN FINISH, (b) Lever Handle with Lock & Strick plate Profile Cylinder with one side key and other side knob -01 nos, (c) Concealed Door Closer slide Arm channel - 01 nos ,(d) Door Stopper,(e) Concealed Drop seal below door - 01 nos etc.,For Single Leaf Glass Door of size : 1200/1100 mm x 2450 mm .As per standards, specification and directed by the Engineer-in-charge.Refer drawing AR/TD/101

Supply & Installation of Aluminium powder coated finish of Door Frames SYSTEM 100 ( Frame) & SYSTEM 100 ( Style ) for Double Leaf Door Frame of section 100mm X 40mm with all required rubber kit & connectors as per Manufacture Standard. The rate to include Door Style using 100mm X 45mm as vertical profile & 100mm X 45mm as top & bottom profile, Using 10mm clear Laminated toughened glass approved brand like (with Glass mounting option) clear crystal edge polished glass fixing as per the required sizes and as per Design detail the rate inclusive of material, Labour & wastages & Scaffolding Complete at all level.The rate inclusive of providing (a) 8nos of Ball bearing hinges 100X70X2mm, SS304, SATIN FINISH, (b) Lever Handle with Lock & Strick plate Profile Cylinder with one side key and other side knob -01 nos, (c) Concealed Door Closer slide Arm channel - 02 nos ,(d) Door Stopper,(e) Concealed Drop seal below Door - 02 nos etc.,For Double LeafGlass Door of size : 2000 mm x2450 mm .As per standards, specification and directed by the Engineer-in-charge.Refer drawing AR/TD/101

Supply and fixing of Double leaf glass door of size 1800x2450 mm with patch fittings: Providing, fabricating and installing at site Double leaf door consisting of 10 mm thick clear laminated toughened glass of approved brand like (with Glass mounting option) including stainless steel patch fittings: Bottom patch SS size 161 x 51 mm with SS Floor Spring Fixed Spindle With SS Cover Plate,90° Hold-Open of standard spring strength , top patch SS size 161 x 51 mm, lock patch with key cylinder size 148 x 43 mm radius of 10 mm, H/D- Type door handle back to back mounted of grade SS- 202 size 300 x 25 mm with dome shaped floor mounted door stopper of required number, clamp fixing (if required) and complete as per the approved architectural drawings and as per standards, specification and directed by the Engineer-in-charge. Note 1. Patch fittings shall be fixed to floor/ wall/ Wooden framework/Ceiling. Rate shall be inclusive of Scaffoldings. Note 2. Consumption of Silicone sealant shall not be less than 75 ml/ Running mt of groove. Note 3. Mode of measurement: The length and width of the finished work shall be measured to its nearest centimetre and area calculated in sqm upto two decimal. Size : 1800mm x 2450mm.Refer drawing AR/TD/101

Supply and fixing of Supply and fixing of Single leaf glass door of size 1000x2450 mm: Providing, fabricating and installing at site Single leaf door consisting of 10 mm thick clear laminated toughened glass of approved brand like (with Glass mounting option) including stainless steel patch fittings: Bottom patch size 161 x 51 mm with SS Floor Spring Fixed Spindle With SS Cover Plate,90° Hold-Open of standard spring strength , top patch size 161 x 51 mm, lock patch with key cylinder size 148 x 43 mm radius of 10 mm, H/D- Type door handle back to back mounted of grade SS- 202 size 300 x 25 mm with dome shaped floor mounted door stopper of required number, clamp fixing (if required) and complete as per the approved architectural drawings and as per standards, specification and directed by the Engineer-in-charge. Note 1. Patch fittings shall be fixed to floor/ wall/ Wooden framework/Ceiling. Rate shall be inclusive of Scaffoldings. Note 2. Consumption of Silicone sealant shall not be less than 75 ml/ Running mt of groove. Note 3. Mode of measurement: The length and width of the finished work shall be measured to its nearest centimetre and area calculated in sqm upto two decimal. Size : 1000x2450mm. Refer drawing AR/TD/101

Providing and fixing of Medium Duty hollow metal fire rated doors as per IS 3614: 2021, for 120min integrity only. Pressed galvanized steel confirming to IS 277 with the following specification.Recommended fire door shall be tested as per IS 17518 (Part 1) from Exova/TBW/CBRI approved lab.Labled fire doors shall be with fire rated hardware and vision panel all as a complete assembly. Proper label confirming the type of door and the hourly rating is mandatory.Same with above Specification but for Single Leaf Shutter of Size : 1100mm x2450mm.As per standards, specification and directed by the Engineer-in-charge.Refer drawing AR/TD/101

Providing and fixing of Standard duty Hollow metal doors confirming to IS 16074 & IS 4351 made of pressed galvanized steel confirming to IS 277 with the following specification. Doors shall be with vision glass and louver as a part of complete assembly.Multipurpose Door FHC Single leaf of size 1200x 1500mm with following Specification,As per standards, specification and directed by the Engineer-in-charge. a.5 Knl, Ball bearing hinges size 4"x3"x3mm, SSS finish, Set of 6 nos b.Mortise shaft lock, H7, 57 BS, SSS finish , 1nos c.Flush pull handle CH 120S, 120mmx40mm,SSS finish, set of 2nos d.Concealed flush bolt -300mm , 1 nos e. Vision panel of Size 200-800mmx800-1100mm f. Foam tape single adhesive 4mm thick g. Non fire rated seal for grooved frame profile. As per standards, specification and directed by the Engineer-in-charge.Refer drawing AR/TD/101

Providing and fixing of Medium duty Accoustic door as per IS 16074 & IS 4351 made of pressed galvanized steel confirming to IS 277 with the following specification. Door shall be suitable for 39db, STC rating.As per standards, specification and directed by the Engineer-in-charge. Same with above Specification but for Double Leaf Shutter of Size : 1800mm x2450mm

Same with above Specification but for Single Leaf Shutter of Size : 1000mm x2450mm

Automatic Sliding Door : Size (Fixed 900mm+Sliding 1800mm+900mm Fixed ) x 2450mm Height Supply, fixing, installation & commissiong of Automatic sliding glass door: Supplying, fixing and installation of Automatic Sliding Glass Door horizontal sliding type. Opening speed of door 45cm/sec/leaf and closing speed is 12-45cm/sec/leaf (adjustable). The door components are Aluminum profiled frame with Glazed panel, Stainless steel rail with Automation system, Hardwares and accessories. size of the door opening. Panel Profile: Precisely designed light weight Aluminum extruded frame sections with provision to fix glass panels. Door Panel: High clarity 10 mm thk clear laminated toughened glass encased in aluminum frame. Top Rail : Durable and anti corrosive Stainless Steel rail highly resistant to damage. Hanger Block: Specially designed Hanger block is equipped with a self cleaning plastic brush and 2 nos rollers of 38 mm Dia. Hanger block with special features of double bearing mechanism, Adjustable bearing mechanism and Automatic balance mechanism. Pulley Unit : Designed to adjust the door movement. Hood Cover: Aluminum Hood cover. Automation System: Electric Drive: High performance Permanent Magnet brushless Automation system encased in aluminum case with stainless steel rail. Driving Timer belt : S8M-10mm width. Motor rating power : 45 Watt and starting power : 180 Watt, Temperature range -20 °C to + 60 ° C. Control: Self monitoring device controlled by micro processor having advance servo control technology. Safety sensing mechanism to stop door closing if object caught in doors. Control integerated with advance features. Effectively designed Auto Reverse System should comprises of Full Range reverse and High Sensitive reverse. Advanced Digital MCU servo control assures slow movement when door closes to gap of 5 cm. In case of power failure, door can be operated manually. Operating Accessory : Push Button, Microwave rader on other side, Key switch, Function switch-open-auto-exit-close, Battery pack UPS, Electronic motor lock. Facility to synchronise accesscontrol card, Remote control with receiver. Safety Accessories : Safety photocell, flashing light, Flashing light with alarm.As per standards, specification and directed by the Engineer-in-charge.

STRUCTURAL STEEL WORK Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete complete at all heights. .Painting steelwork with two or more coats of Synthetic enamel paint of Ist quality and approved colour to give an even shade over two coats of zinc rich apoxy primer (70 micron) including, filling the joint welding with metal Paste and cleaning the surfaces, Working platfrom/scaffolding & the DFT test of primer & paint etc; complete all as per specifications (Rate to include cost of zinc chromate primer also). Complete at all levels and locations.As per standards, specification and directed by the Engineer-in-charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete at all heights. Painting steelwork with two or more coats of Synthetic enamel paint of Ist quality and approved colour to give an even shade over two coats of zinc rich apoxy primer (70 micron) including, filling the joint welding with metal Paste and cleaning the surfaces, Working platfrom/scaffolding & the DFT test of primer & paint etc; complete all as per specifications (Rate to include cost of zinc chromate primer also). Complete at all levels and locations.As per standards, specification and directed by the Engineer-in-charge.

Providing 25mm thick NON SHRINK Grouting of approved make between Base Plate and Column as shown in drawing.As per standards, specification and directed by the Engineer-in-charge.

Providing and fixing mild steel round holding down bolts with nuts andwasher plates complete.As per standards, specification and directed by the Engineer-in-charge.

Supplying, Fabricating and erecting in position of Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.As per standards, specification and directed by the Engineer-in-charge. Frame work for counter

FLOORING , SKIRTING, CLADDING,COUNTERS,LEGDE, THRESHOLD WORKS Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 with 20 mm nominal size stone aggregate,all complete As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/103

52 mm thick Cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc., all complete As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/103

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/103

CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT 12 mm cement plaster finished with a floating coat of neat cement of mix : 13.7.2 1:4 (1 cement: 4 fine sand) all complete As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/103

Supplying and fixing 10 Gauge weld mesh of size 100mm x 100 mm for floor/roof slab concrete screed over the micro beams as reinforcement. The weld mesh shall be fixed as per drawing. The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/212, AR/TD/213

Supply, fixing and installation of 8 mm to 8.33 mm thick laminated wooden flooring classification of use 31/23 with a surface abrasion resistance of class AC5. Grade 0.2 mm thick wear layer on top of a high density fiber substrate. Sub floor on which the planks are being laid should be smooth, flat , hard & free from moisture , grease etc., In case of uneven sub floor the same should be levelled by self levelling compound ( paid seperately ). The moisture level present in the sub floor should be less than 8% before installation of the floor. Plank size 1215 mm x195 to 197mm having locking arrangement with an under laying made of natural colour foam, with accessories like end profile, transition profile, reducer, stair nosing, the item including supplying and fixing of skirting profile & door profile to the flooring. etc, As per standards, specification and directed by the Engineer-in-charge. Basic rate: Rs. 140/ SFT, The purchase price ( excluding GST ) of laminated wooden panels is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and Laying wooden hardwood flooring of approved make and pattern and as per architectural drawing and instructions of thickness 15-18 mm or as per manufactures details , consisting of 3 layers the top precious wood, the core layer is arranged below it in a cross grain direction which increases stability, the ply construction features a balancing veneer at he bottom which ensures superior dimensional stability. This make is excellently suited for installation as floating floor. The quality of hardwood floor stands and falls with the surface finish. The practical solution for the flooring is UV high finishes. Before laying the flooring, it shall be ensured that the base floor is clean, level and thoroughly dry. The flooring shall be installed by first laying of polythene sheet 0.5 mm thick on the base floor, on the top of which will be laid a 2 mm thick polyethylene cell foam jointed with tapes. The rate is inclusive of all operation, floor protection sheet, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Basic Price : 400/Sft, The purchase price ( excluding GST ) of engineered wooden panels is mentioned basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying of Carpet Tile of 600x600/500x500mm over the specified area with following specification. The carpet is to be laid over a bed of approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing and clearing away of residual material to a location as directed. The rate shall also include supplying and laying of a protective layer of PVC or HDPE sheet of 50 microns thickness, held together with scotch tape. The laid carpet to be vacuumed after the removal of protective cover/on commissioning. If after the protective layer is removed and stains observed in the carpet because of in adequate protection, the same shall be shampooed and made good to the satisfaction of the EIC. The measurements of carpet will be the actual laid area. Providing & laying carpet tile with following specification: Style: Tile or Roll , Composition - 100% Nylon , Single/Multi Level Loop , 1/10 to 1/12 Gauge ,Pile Height 10-12mm, 16 Oz Pile Weight +/- 10% , Plank Form - Dimension - approx 25 cm x 100 cm, or Tile form size - 60 x 60 cms or as per per manufacture's detail. 100% Solution Dyed , Total Thickness 6 mm +/- 10% , Pile Weight - 543 gsm ±10% , Protekt²® / Similar Soil/Stain Protection , Above with PVC / Fiberglass Backing The rate inclusive of material , labour , Installation , protective layer , required profiles , Cleaning etc., all operation, material and required As per standards, specification and directed by the Engineer-in-charge. Basic rate: Rs. 200 / Sft, The purchase price ( excluding GST ) of carpet tiles is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Supply, fixing and installation of 75mm aluminium skirting of approved shade /colour of hairline finish with clip system by fixing the base frame with screws and necessary fastners to the partition walls / floor etc. The rate is inclusive of all operation, material and required pattern. As per standards, specification and directed by the Engineer-in-charge. Basic rate: Rs. 220/ Rmt, any deviation +/-,The purchase price ( excluding GST ) of aluminium skirting is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103, AR/TD/212, AR/TD/213

Providing and Fixing of 6mm thick rubberized flooring, suitable for use in Gymnasium and heavy traffic areas, conforming to DIN 18032 part 2 and EN 428. The product should have a top layer of 2-mm vinyl surface and 4 mm thick vinyl foam backing layer. The top layer should consist of at least 0.7-mm clear transparent wear layer and glass fiber reinforcement for dimensional stability. The product when tested should be able to confirm to the performance parameters as per DIN 18032 part 2 and EN 428.The rate is inclusive of all operation, material and required pattern. Basic rate: Rs.170/ Sft, any deviation +/-,The purchase price ( excluding GST ) of rubber floor is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/103

Providing and finishing of homogenous self levelling compound of thickness 3mm of Approved make as specified by manufacture of approved Shade - Under lay System Etc., As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/103

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete As per standards, specification and directed by the Engineer-in-charge. Base Price ; 220/Sqft, The purchase price ( excluding GST ) of a granite slab is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and fixing 18 mm thick gang saw cut flamed finish grainte, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Base Price ; 220/Sqft, any deviation +/-, The purchase price ( excluding GST ) of granite slab is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Kota stone slab/ tile flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Base Price ; 60/Sqft The purchase price ( excluding GST ) of kota stone is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Kota stone slabs/tile 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Base Price ; 60/Sqft, any deviation +/-,The purchase price ( excluding GST ) of kota stone is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying vitrified floor tiles of Size:600x600x9mm of 1st quality with water absorption less than 0.08% and conforming to IS: 15622, of approved make,shades and pattern, laid on cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980 and matching pigmen, including the cost and conveyance of all materials, labour charges , lead , lift , curing etc., complete and tile protection till handover as directed by Engineer in charge at all levels . The rate includes cutting the sharp edges of tiles with specialised machinery where ever required . The purchase price ( excluding GST ) of Vitrified tile shall be as mentioned below in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. The work shall be carried out by an agency having good experience with the skilled labours on the specified work mentioned above.The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Base Price ; 60/Sqft, any deviation +/-,The purchase price ( excluding GST ) of Vitrified tilee is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying vitrified floor tiles in different sizes & thicknessof the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS 15622, of approved make, in all colours and shades, in skirting, riser of steps, overcement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980, and matching pigmenetc. complete.The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Glossy Finished tiles of Size 600 X 600mm Basic Price of Vitrified Tiles : 60/SFt, The purchase price ( excluding GST ) of vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying Full Body Vitrified tiles Polished finish in floor in different sizes & thicknessof the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigmen etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Size of tiles shall be 600mmx1200mm Basic Price of Tiles : 200/SFt, The purchase price ( excluding GST ) of full body vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying vitrified floor tiles in different sizes & thicknessof the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS 15622, of approved make, in all colours and shades, in skirting, riser of steps, laid over cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980 and matching pigment etc. complete.The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Tiles of Size 600 X 1200mm Basic Price of Tiles : 200/SFt, The purchase price ( excluding GST ) of vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying full body Vitrified Matt/Anti Skid finish Tiles in floor in different sizes & thicknessof the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Size of tiles shall be 600mmx600mm Basic Price of Tiles : 70/SFt, The purchase price ( excluding GST ) of full body vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying Glazed Vitrified Tiles in Walls in different sizes & thicknessof the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Size of tiles shall be 600mmx600mm Basic Price of Tiles : 70/SFt, The purchase price ( excluding GST ) of glazed vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/222, AR/TD/223, AR/TD/224, AR/TD/225

Providing and fixing Designer tiles on finished plain Floor surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design with 2mm Spacer joint as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by As per standards, specification and directed by the Engineer-in-charge. Basic Price : 310/Sft, The purchase price ( excluding GST ) of designer tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment, etc. complete The rate is inclusive of all operation, material and required pattern As per standards, specification and directed by the Engineer-in-charge. Basic Price : 310/Sft, The purchase price ( excluding GST ) of ceramic glazed tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/220

Providing and laying of full body Vitrified Matt/Anti Skid finish Tiles in floor in different sizes & thicknessof the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.As per standards, specification and directed by the Engineer-in-charge. Size of tiles shall be 600mmx1200mm Basic Price : 200/Sft, The purchase price ( excluding GST ) of fullbody vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying Glazed Vitrified Tiles in Walls in different sizes & thickness of the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid oncement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.The rate is inclusive of all operation, material and required pattern,as per standards, specification and directed by the Engineer-in-charge. Size of tiles shall be 600mmx1200mm Basic Price : 200/Sft, The purchase price ( excluding GST ) of glazed vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206

Providing and laying Vitrified Matt/Anti Skid finish Tiles in floor in different sizes& thickness of the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.As per standards, specification and directed by the Engineer-in-charge. Size of tiles shall be 200mmx1200mm Basic Price : 140/Sft, The purchase price ( excluding GST ) of full body vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying vitrified floor tiles in different sizes & thickness of the tiles should be 9/10mm with water absorption less than 0.08% and conforming to IS 15622, of approved make, in all colours and shades, in skirting, riser of steps, over cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) having spacers 2mm with spacer filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment etc. all complete as per Architectural drawings, and ss per standards, specification and directed by the Engineer-in-charge. Matt Finished tiles of Size 200 X 1200mm Basic Price : 140/Sft, The purchase price ( excluding GST ) of vitrified tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and fixing Designer tiles on finished plain wall surface of size 20 mm x 20 mm x 12 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and epoxy grouting of the same. The rate is inclusive of all operation, material and required pattern as per standards, specification and directed by the Engineer-in-charge. Basic Price : 310/Sft, The purchase price ( excluding GST ) of designer tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying machine cut, mirror polished Italian Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing, polishing and inculding floor protection sheet etc. all complete As per standards, specification and directed by the Engineer-in-charge. Basic Price -350/Sft, The purchase price ( excluding GST ) of italian marbel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and fixing machine cut, mirror/ eggshell polished , Italian Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as per standards, specification and directed by the Engineer-in-charge. Basic Price -350/Sft, The purchase price ( excluding GST ) of italian marbel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and laying machine cut, mirror polished Italian Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing, polishing and inculding floor protection sheet etc. all complete as per Architectural drawings, and as per standards, specification and directed by the Engineer-in-charge. Basic Price -600/Sft, The purchase price ( excluding GST ) of italian marbel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/103

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut italian marble for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over cement based high polymer modified quickset adhesive conforming to IS:15477, in thickness (as per manufactures' specification) filling with resin based epoxy grout with high degree of resistance to chemical attack,abrasion and resistance confirming to British Standards 5980:1980and matching pigment , epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. all complete as per Architectural drawings, and as per standards, specification and directed by the Engineer-in-charge. Basic Price : 350/Sft, The purchase price ( excluding GST ) of italian marbel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/202, AR/TD/203, AR/TD/216

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. all complete as per Architectural drawings, and as per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/203

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and epoxy grouting of the same. The rate is inclusive of all operation, material and required pattern as per standards, specification and directed by the Engineer-in-charge. Basic Price : 280/Sft, The purchase price ( excluding GST ) of glass mosaic tile is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/201

FALSE CEILING WORKS Supply, fixing and installation at all height FALSE CEILING including providing & fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating 120gsm as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts to the angle hangers of 25x10x0.5mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section & perimeter channels 0.5mm thick 27mm high having flanges of 20mm & 30mm long, the perimeter of ceiling fixed to wall partition with the help of rawl plugs at 450mm centre to centre with 25 mm long drive-all screws @ 230mm interval including jointing & fixing to a flush finish of tapered & square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification & also including the cost of making openings for light fittings, grills, diffusers, cove light , cutouts made with frame of perimeter channels suitably fixed all complete as per drawing & specification and direction of the Engineer in Charge but excluding the cost of painting with: i) 12.5 mm thick tapered edge fire resistant GYPSUM BOARD CONFORMING TO IS: 2095- PART-I. The rate inclusive of all required Nice / veriticles upto 300/450mm Depth , materials, transport, required scaffolding including providing & removing of the same , etc. complete.As per standards, specification and directed by the Engineer-in-charge. NOTE: Only false ceiling area will be measured from wall to wall. And no deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.

Providing and fixing suspended false ceiling using 12 mm Calcium Silicate board which includes providing and fixing GI perimeter channels of size 0.55 mm thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm, 22 gauge with two flanges of 15 mm each from the soffit at 18" to 24" centres with suitable ceiling supports fixed to soffit with GI cleat and steel expansion fasteners. "Jali" shall be fixed to the cross frame with screw and washer arrangement (Confirming to IS-2095-1982). If required Plaster of paris punning done to suitable thickness to attain uniform surface Multi level ceilings with curvature / steps/ chamfer shall be done as per the reflected ceiling plan . Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. The rate shall inclusive of providing Joints filling compound with adhesive tape between the boards ,Cove light ..cut out for AC , Light fittings , Speakers, Smoke and fire detectors ,transport, required scaffolding including providing & removing of the same etc., to complete the work as per Engineer - In- Charge. Note: For Light fittings, Grills, diffusers and other cut-outs have to be made with a frame of perimeter channels of size 20mm x 27mm x 30mmx 0.55mm thk, supported suitably. NOTE: Only false ceiling area will be measured from wall to wall. And no deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.

Providing and fixing internal ceilings panels on Light gauge steel frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on Cement Bonded particle board 8 mm (Termite, Fire & Moisture Resistance), as per IS:14276 : 1995 and as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make , MS supports with RHS 50x25mm at 60cm c/c connected to main farme , Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. The rate shall inclusive of tape between the boards , 50x25 Box section at every 600c/c finishes with one coat of metal primer and a coats of approved coloured enamel paint ,Cove light ,cut out for AC , Light fittings , Speakers, Smoke , fire detectors , materials, labour cost,transport, required scaffolding including providing & removing of the same etc., to complete the work as per Engineer - In- Charge. Note: For Light fittings, Grills, diffusers and other cut-outs have to be made with a frame of perimeter channels of size 20mm x 27mm x 30mmx 0.55mm thk, supported suitably.As per standards, specification and directed by the Engineer-in-charge. NOTE: Only false ceiling area will be measured from wall to wall. And no deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm. Refer drawing AR/TD/102

Providing and fixing Jute Baffle made out of natural Jute material of Hollow Door profile , size of member 86x31mm , 31mm reading and 75mm gap with horizontal support of 9mm rod to maintain length & level as per vendor Details . Primary Profile should be fixed to wall/Beam with proper fixing with screws with plug & secondary profile to cut so that it can be rest on Primary profile as per vendor details and maintained spacing & level with pin rod by drilling the secondary member & finishing the holes etc. The rate is inclusive necessary fittings, Installation, material, labour, transport , tools, required scaffolding including providing & removing of the same , etc .complete to the requirement the works As per standards, specification and directed by the Engineer-in-charge. Basic Price : 280/Sft, The purchase price ( excluding GST ) of jute baffle is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing.Refer drawing AR/TD/102, AR/TD/205, AR/TD/206

Providing & fixing Vertical Linear Baffle Ceiling made out of Aluminium Extrusion in Aluminium alloy grade 6063. The baffle blade shall be in size of 100x 25 x 3600mm and finished powder coated of approved shade as per manufacture's recommendation . The baffle blade shall be suspended using Slotted U-profile at on-center spacing in multiples of 25mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. ( Ceiling GI Drop as per Site Condition Approximate 2.0mts ) Installation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter. The rates includes Material, Labour,Scaffolding, cleaning etc., complete at all levels as per Engineer Incharge. Installation of Baffles: Locate the slot for Baffle Hangers in slot of Baffle section at 1200mm centres. Hangers are inserted into the slot, then rotated 90° and fixed into position by tightening the grub screw. Baffle to be lifted into position and hangers engage over lip of U-Grid Channel. Each Hanger to be secured into position by inserting the Locking Clip. Baffles blades to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into Baffle slots.Installation shall be according to the instructions provided by manufacturer. The rate is inclusive necessary fittings, Installation, material, labour, transport , tools, required scaffolding including providing & removing of the same , etc .complete as per manufacture's specification & to the requirement the works As per standards, specification and directed by the Engineer-in-charge. Basic Price Rs400/Sqft. The purchase price ( excluding GST ) of baffele ceiling tile is metioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206 Refer drawing AR/TD/102, AR/TD/211, AR/TD/221

Providing and Fixing Woodworks Linear of nominal width 150mm, having 130mm wide panel with 20mm reveal having a thickness of 15mm thickness and length 2400 mm. The panel shall be made of a Moisture resistant fibre board substrate having a minimum density of 595 Kg/m3 with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut) and a melamine balancing layer on the reverse side. The panel shall have 0.7mm PVC edge banding along the length side with a similar finish as that of the face. The back of the panel shall have a black acoustic felt to cover the reveal of 20mm to attain an NRC of 0.4 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423. The panels shall provide a Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm. The back of the panels shall be profile-grooved to receive 3600mm special linear carrier (PeakForm Prelude XL Main Beam) with integrated factory fitted clips for installation.The panels shall be upward mounted on Cieling Solutions Peakform Prelude XL Main Bars with 24 mm wide T - section flanges having rotary stitching along the length of the beam with a web height of 43mm. The Main Beam shall have integrated (factory fitted) locking clips installed at 150 mm centre to centre distance. The deflection loading of the main beam tested as per ASTM C635 (Deflection limit less than L/360) shall be at least 21.4kg/m. The end details of the main beam shall be made of pre hardened steel and fixed to the ends with 3 point fixing. All main beam to main beam connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 100 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. Installation should be carried out as per the manufactures details . The grid shall be installed with suspension system of specified make.SUSPENSION SYSTEM accessories manufactured and supplied by the make specified consisting of M6 Anchor Fasteners with hanger hole, pre–Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. Additionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners etc complete as per manufacture details. The rate shall inclusive provision of Liners lights /Cove light ..cut out for AC , Light fittings , Speakers, Smoke and fire detectors ,transport, required scaffolding including providing & removing of the same etc., to complete the work As per standards, specification and directed by the Engineer-in-charge. Base price 400/ sft. The purchase price ( excluding GST ) ofwoodwork liner panels is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/101, AR/TD/205, AR/TD/206Refer drawing AR/TD/102, AR/TD/203

Providing, fabricating and fixing MS Grid Ceiling with Bright MS bars (Bright steel conforming to IS : 226 and IS : 2062 with minimum yield strength of 250 Mpa and upto 500 Mpa ) for ceiling as per architectural drawing and instructions. The system shall be consist with 50mm x50mm and 8mm thick base plate fixed in RCC member with anchor bolt ( 3/8 size) c/c as per site condition and given the drawing. The verticale / horizontal member shall be consist with 20/25 mm bars and supported from ceiling for a depth upto 1000 mm , Ms Bar welded to the plate properly as per architectural drawing including necessary hardware, anchor bolt, cutting, grinding, machining, assembly, welding, jointing, drilling, grouting and cleaning etc. completed as per the instructions of EIC/ Architect . MS sections to finish with by applying one coat epoxy primer of MRF or equivalent and finish with two coates of approved quality enamel paint of MRF or equivalent etc. The rate inclusive of Material, Labour, Installation , providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/204

Supply, assembly, installation, testing & commissioning of approved make stretch fabric decorative luminaire along with necessary accessories. The shape and dimension of luminaire shall be as per tender intent drawing. The housing shall be made of High quality aluminum 6063 T6 Grade, Powder coating color as approved. Supply & Installation of Printed Premium PVC Membrane duly welded with PVC harpoon and Aluminium Europrofiles in anodised finish. Installation by using heat stretching method should be free from wrinkles and any visible sag. The Stretch Ceiling should be warranted for 10 years against any manufacturing defect. PVC Membrane adhering to EN 14716 standards, with following test certificates: * Fire: b-s1-d0 , * No Heavy Metals , * A+ Emission , * UL Classified (India)As per standards, specification and directed by the Engineer-in-charge. Base price of stretch fabric Rs.575/sft The purchase price ( excluding GST ) ofstretch fabric is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/101, AR/TD/205, AR/TD/206Refer drawing AR/TD/102, AR/TD/208

Design, Supply & Installation of Aluminium plain/wood grain finish Strip ceiling system at all levels for external /interal application complies with IS 875 part 3 1987 on wind loading, the same should be tested for and complying to a wind load resistance of minimum 1.2 kpa (as tested by an independent and competent authority) as per prevalent and in practice wind loading norms and procedures. The system consists of strip panel size 300mm X 3000mm and mimimum 30mm deep with bevel I square edge manufactured out of 0.7mm thick or above stove enameled coil coated on continuous paint line/ polyster powder coated and double baked, roll formed from corrosion resistant aluminum alloy A3005/3003/3105, according to AST C635, ASTM E1264, EN 13964 and quality standards of TAIMe. V: latest version or equivalent standards and thickness according to static requirements. The system shall be perfectly levelled, aligned at desired height in plain, curved and vertical face in accordance with the false ceiling patter as per drawing and the system shall be installed. Panels shall be formed with tiling up vard bending at both sides and further inward bending flange on two side for clipping onto the proprietary modular carriers. The suspension system consists of clip -in profile shaped special secondary profile of 1 mm thick black coated galvanized steel of 5mrs of suitable size, shape and strength shall be used to support the strip panel up to 3 meter, positioned at maximum 150mm distance from both ends of the panel and inbetween at a maximum distance of 750mm c/c. Connecting clips or nuts/bolts of galvanized steel is used to connect primary and secondary profiles. The profile suspension clip of galvanized steel to join the primary angle to threaded suspension rod of 8mm with ceiling brackets and necessary fasteners/ Pand shall be clipped to a baked enamelled Aluminium carrier of 41.5 mm mde × 62 mm deep x 0.95 mm thick in standard length of 5 mtrs, positioned at maximum 150 mm distance from both ends of the panels and in between at maximum distance of 750mm c/c. Panel carrier shall be fixed by means of MB nut bolts at 550 mm c/c to the suitable sunstructure provided by others or equivalent, in accordance with Manufacture's specifications and directions of the Engineer-in-Charge. The panels shall be individually locked with the provision available in the panel carer. The system shall be installed in line and level and as approved by Engineer-in-Charge. The threaded rod will be suspended from the slab/purlins/ substructure with necessary fasteners with expansion bolts at 1200mm c/c maximum and the primary profile spaced al 1200mm c/c maximum and secondary profile spaced at 750mm c/c maximum. The strip panels shall be inserted on the clip-in profile carrier The panel should be rolled formed with square / bevelled edges decided as per the site mock up and instructions of Engineer-in-Charge. The aluminium strip panels shall be weather - fast, dirt retending and scratch resistant of 0.7mm thickness or above shall be polyster powder coated on continuous paint line with minimum 80 (microns/stove enarnelled coll coated with minimum of 30 microns with 20% gloss with premium plain colour or wood finishes. The suspension system consisting of camer, hanger, threaded rod, perimeter profile/ edge trim, security clips etc. shall be provided in accordance with approved Manufacture's standard specification and directions of Engineer-in-Charge. The suspension system shall be consists of secondary carrier 1mm thick galvanized steel, primary L camer 30×30×2mm galvanized steel and hanger 20x70x2mm threaded rod 8mm, C shaped perimeter profile 20x40x20mm and 0.7mm thick edge profile or equivalent, in accordance with Manufacture's specifications and directions of the Engineer-in-Charge. Edge profile and perimetre profile shall be of prepainted Aluminium and color matching with the strip panels etc. Ceiling termination, edge trim shall be as approved by Engineer-in-Charge. The rate shall also include the cost of making openings of any shape and fixing of light fittings, grills, diffusers, smoke extractor fan openings. Air terminal devices for HVAC, cul-outs etc. made with frame of perimeter channels including wall trim/edge trim and infinity profiles of 300 mm width to create perimeter encloser, interface carrier for other materials as per drawing and finishing the edges as directed by Engineer-in-Charge. The purchase price( excluding GST) for ceiling tiles and suspension system should be taken as R$ 3975/sqm. any deviation plus or minus in the purchase price( excluding GST) in approved shade will be adiusted(paid extra or deducted) while making payment to the contractor. The rate shall include cost, conveyance lead, lift of all materials, labour, scaffolding charges, clearing all refuse, rubbish, etc. complete as per drawngs, specifications and direction of Engineer-in-Charge. Contractor should submit detailed design and corresponding calculations of design of all structural suspension system of metal false ceiling, structural steel support and shop drawings vetted by the consultant in accordance with design parameters specified by the Consultant and the codal requirements of BIS (Bureau of Indian Standards) latest version, all relevant safety codes, National Building Code and DIN ISO 9001, LEED & DGNB. EN 13964, EN 13501-1 building material class A2-s1, 40 Class A tested to ASTM E 84 class 0 tested to BS 476 part 6/., E DIN EN ISO 354 , ASTM C 423 etc to the Engineer-in-Charge/Consultant. Only skilled and experienced persons shall be employed for this purpose and should ensure guarantee for proper installation, material composition & quality performance of both ceiling panels and supporting system for a period of 10 years from the date of completion of the said work The measurement shall be laken along the girth on the bottom s'te of the ceilings, in square meters and deductions shall be made for all openings exceeding 0.4 som in area. The structural steel work required for this work will be paid in the respective item seperately.As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/102, AR/TD/211

Providing and Fixing hard wood battens of 100x75 mm (radial type) ceiling with 6mm thick HPL using structural frame work of ISA 50x50x6mm (shall be measured and paid under relevant item)suspended from the exisung slabstructure al a spacing of 1200mm C/C. Hard wood grid shall be provided over the HPL surface as per design and drawing. The surfaces of hardwood finished with sand paper, filling of grains with wood filler and dent filler, applying approved wood stain for geting required shade applying two coats of PU sealer, two coats of PU top coat etc complete as per direction of Engineer in charge at all levels. The ceiling shall be fixed to the roof soffit with adequate suspenders. The lem shall be inclusive or curting & making cutouts for lights, diffusers etc all complete. The rate is including cost and conveyance of all materials, labour charges, lead.lift, scaffoldiny at all heights (upto 7.5m height) fixing the lighting to roof,PU finish, sundnes elc complete as direcled by Engineer- in-Charge at all levels. wooden plank (radial type) ceiling. Only the exposed finish surface area without projections of battems shall be measured for payment.As per standards, specification and directed by the Engineer-in-charge. Basic Price : 380/Sft, The purchase price ( excluding GST ) of HPL panel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/102

Providing & fixing 12mm thick marine grade ply ceiling confirming to IS -710 using structural steel frame work ( paid seperately under releveant item) suspended from the existing slab/ Ms structure . The ply shall be finished with approved emulsion paint at back side as per direction of EIC at all levels . The ceiling shall be fixed to the existing slab/ Ms structure with adequate suspenders. The rate shall be inclusive of cutting & making cutouts for lights , diffusers, supports for ceiling suspended fixtures , materials , labour charges, lead , lift , providing & removing required scaffolding etc complete As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/210, AR/TD/211, AR/TD/212, AR/TD/213, AR/TD/221

Providing & fixing Access panel of Size specified below with - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard of approved make , Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10. Powder coating - Color: white, RAL 9010 or as per Approved shade . The rate inclusive of Material, Labour, Installation , providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Size 300x300mm.

Providing & fixing Access panel of Size specified below with - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard of approved make , Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10. Powder coating - Color: white, RAL 9010 or as per Approved shade . The rate inclusive of Material, Labour, Installation , providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Size 450x450mm

Providing & fixing Access panel of Size specified below with - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard of approved make , Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10. Powder coating - Color: white, RAL 9010 or as per Approved shade . The rate inclusive of Material, Labour, Installation , providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Size 600x600mm

Providing & fixing Access panel of Size specified below with - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard of approved make , Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10. Powder coating - Color: white, RAL 9010 or as per Approved shade . The rate inclusive of Material, Labour, Installation , providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Size 600x1200mm

Curved Shape Ply Boxing finished Veneer Suspended Ceiling. Providing and fixing of Curved shape Veneer ceiling Boxing of Size ( 1600mm W x 1000/1450mm H ) formed out of 12mm thick marine ply confirming to IS -710 boxing with necessary framework , fixed rigidly to the true ceiling / ms frame structure with necessary hardwares like SS clutch cables and anchor fasteners . The ply boxing to be finished on all sides with approved 4mm thick veneer over 12mm thick ply as per detail drawings. TVeneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat as pe the requirement by the architect . The rate shall include all connectors, accessories, fastners, profiles, adhesive tapes, seals, making necessary opening and accessories forAC grille / Electrical/Data/Voice switches, cove ligth , sockets ,materials, labours, scaffolding, leads and lifts etc. all complete as per approved shop drawings and As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Surface area with Length Basic price of Veneer : 220/Sft, The purchase price ( excluding GST ) of veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/201

Baffle Ceiling : Supply & Installation of baffle Beam ceiling this shall consist of 'Box' shaped 1.4mm thick aluminium extruded section , The size of the 'Box' sections shall be 150mm wide and 200 height as per design with baffle to baffle and centre to centre distance (which can be modified as per requirement). available in various lenghths 1000mm to 8250mm ,as per architectural drawing .The baffles shall be fixed to each other using framework of size 25mmx15mm made using 0.8mm thick GI sheet which is folded and bent to desired profile finished with powder coating. These mild steel framework/sections shall be inserted between two members and fixed using self interlocking system. The mild steel framework in turn are fixed on to he true ceiling above using a suitable suspension system consisting of nuts, Washers, 6mm GI rod and anchor fasteners. This ceiling facilitates easy maintenance. Rate to includes necessary supports as per manufacturer specification. The ceiling and the accessories are provided with powder coated thickness of 70-80 microns os approved by the EIC.The rate shall include all connectors, accessories, fastners, profiles, adhesive tapes, seals, electrical cutouts, cove ligth ,materials, labours, scaffolding, leads and lifts etc. all complete As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Perimetre of Section with Length measured as sqm. Basic Price : 400/Sft, The purchase price ( excluding GST ) of baffle beam is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing.Refer drawing AR/TD/201

Providing , fabricating , assembling and installation of 19 mm thick Marine grade Ply confirming to IS -710, Wardrobe of sizes 2450x1200x600 mm deep , the internal body of the wardrobe made of 19 mm MR grade ply and finished with 0.80 mm thick laminate internally . The overall unit made out of 19 mm marine grade ply & of 4mm thk veneer finish externally. The unit consists inside with shelf and space for provision of locker & Mini bar unit seperated by shelve and also ventilation for bar unit to be considered as per the detailed drawings. The wardrobe shall have provision for LED concealed light & minibar unit with contact switch. The Bottom section of the wardrobe shall palced at 75mm higher and 50mm recessed inside for cladding skirting (paid seperately ).The two, two-ways openable shutters made of 19 mm thick ply having 4 mm thick Veneer of Approved shade & Veneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat as pe the requirement by the architect , unit inside portion shall also have 1 no hanger rod made from 25mm X 25mm Aluminium black matt powder coated pipe ,including with necessary hardware and accessories like handles , hinges , locks , hangers , 3 no powder coated robe hook ,rods etc with all tools , labour , providing & removing scaffolding ,etc all complete as per the specification and design drawing and as per standards, specification and directed by the Engineer-in-charge. Note : Shop drawings to Produce before production. Mode of Measurement : Front Elevation Basic price Of Veneer : 150/sft, The purchase price ( excluding GST ) of veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206

Providing and fixing in position, Bed base of sixe 1600 mm (W) x 1900mm (L) x 320mm (H) size made out of 18mm marine ply confirming to IS -710, as per the design, finish & quality etc. as per architecture drawings. and fixing 1mm thk laminate to the bed base by pasting the laminate with suitable adhesives and bed sides made of 150mm Depth with 18mm grade and top members finished with 4mm thick veneer of Approved shade and finished with PU coat . complete as per approved shop drawings, technical specifications, sketches / images and as per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan Area Basic price Of Veneer : 150/Sft Basic price Of laminate: Rs.80/sft. The purchase price ( excluding GST) of veneer & lamonate are mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206

Providing and fixing in position, Bed base of sixe 900 mm (W) x 1900mm (L) x 320mm (H) size made out of 18mm marine ply confirming to IS -710, as per the design, finish & quality etc. as per architecture drawings. and fixing 1mm thk laminate to the bed base by pasting the laminate with suitable adhesives and bed sides made of 150mm Depth with 18mm grade and top members finished with 4mm thick veneer of Approved shade and finished with PU coat . complete as per approved shop drawings, technical specifications, sketches / images and as per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan Area Basic price Of Veneer : 150/Sft Basic price Of laminate: Rs.80/sft. The purchase price ( excluding GST) of veneer & lamonate are mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206

Providing and fixing Study / TV Ledge of size L of Various size , D-450mm x 40mm thick including making the ledge by combining 18mm and 12mm Marine ply confirming to IS -710 fixed at 750mm from finished floor with required supports from the wall behind . The ledge shall in the form of screws with PVC plugs into the back wall. The ledge shall finish with veneer of 4mm thk as per design details as per drawings . Veneer Surface has to be finished with approved shade of PU finish. Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat as pe the requirement by the architect .including providing the cutouts required for fixing of electrical switches etc. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and as per standards, specification and directed by the Engineer-in-charge. Basic price of Venner : 220/Sft, The purchase price ( excluding GST ) of veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206

Providing & fixing Mirror Paneling including Marine ply confirming to IS -710 paneling made out of 18mm thick ply wood board fixed over Aluminium framework of 20mm X 50mm sections at approximately 600 mm c/c both ways with adequate supports from the wall. The ply shall be fixed with 6mm thick clear mirror with all sides CNC machine polish using 3M mirror tape on sides and clear neutral silicon in center. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and as per standards, specification and directed by the Engineer-in-charge.

Providing and fixing Vanity counter of size in various Lengths , D-500mm with front facia of 50mm made by fixing 18mm fiber cement board boxing to the toilet wall with adequate supports in form of MS bracket. Fixing with 20mm thick Quartz on top of the counter table ( paid seperately ) with araldite epoxy adhesive on top and sides of the counter, with mitered joints. making provision in the counter top for fixing counter sunk wash basin and for fixing tap. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, MS brackets to be painted with two coats of Enamel paint over a coat of approved Zinc chromate primer, leads and lifts etc. all complete as per approved shop drawings and as per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan area. Refer drawing AR/TD/205, AR/TD/206

Supplying ,handling & placing of 20mm thick polished quartz for counter. The is inclusive of wasteage , protection etc complete as per the requirement As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan area Basic Price Of Veneer : 450 /Sft, The purchase price ( excluding GST ) of quartz is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing

Providing and fixing vanity Ledge of size L of Various size , D-450mm x 40mm thick including making the ledge by combining 18mm and 12mm MR grade ply confirming to IS -710 fixed at 300mm from finished floor with required supports from the wall behind. The ledge shall be fixed to the dry wall/block walls with adequate support inside drtwall to fix ledge and ledge is fixed with the help of screws with PVC plugs into the back wall . The ledge shall be finished with Approved 1mm Thk Laminate with adhesive to match control sample. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and as per standards, specification and directed by the Engineer-in-charge. Basic Price of Laminate : 80/Sft, The purchase price ( excluding GST ) of laminate is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206

Supply and installation of vanity mirror of overall size 1200/1100 mm X 950mm including making mirror boxing of total depth 60mm using SS 'L angles fixed with angle cleated on all 4 corners, fixing 6mm extra clear mirror with all sides CNC machine polish with mirror tape on the frame edge with adequate support. The mirror shall nave a square frosted band of 35mm width leaving 40mm distance from all 4 edges. Provision to be made for back lighting the inside the ss box. Including fixing Dimista pad behind the mirror to act as a defogger. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and as per standards, specification and directed by the Engineer-in-charge.

Providing and fixing Vanity counter of size in various Lengths, D-500mm , H-450mm with front facia of 50/75mm made by fixing 18mm MR grade ply boxing to the toilet wall with adequate supports in form of MS bracket. Fixing with 20mm thick Quartz on top of the counter table ( paid seperately ) with araldite epoxy adhesive on top and sides of the counter, with mitered joints. making provision in the counter top for fixing counter sunk wash basin and for fixing tap. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. The Unit below counter is made of 19mm thick maraine grade play and consist of three units. i. The centre unit of 450mm x 600mm with double shutter made wooden beading all four side and with 20x10/6mm wooden strips placed inclinedly at 25mmc/c and finished with melamine polish and inside surface finished with approved laminate etc as per detailed drawing . ii. The other two units on either side without shutter and exposed surface finished with approved laminate . The work shall include all materials, labours, scaffolding, tools & tackles , necessary hardware and accessories like handles , hinges , any cut-out for services, MS brackets to be painted with two coats of Enamel paint over a coat of approved Zinc chromate primer, leads and lifts etc. all complete as per approved shop drawings and as per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Elevation area

Supply, fixing and installation of Kitchen Unit with waterproof BWR grade plywood finished Inside with 0.8 mm laminate, Post form shutters of waterproof MDF/ BWR grade plywood with 1mm laminate in facia and 0.8 mm laminate on backside. Bow Handle Zinc Alloy die cast with satin finish of 202mm Pitch (for Floor Unit), 90 degree hinges with soft close for hinged doors, M10 screw type leveller with Hexagonal plastic base and all cooking, bottle pullout baskets, etc of SS 304 grade of Approved make. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm, including transportation and installation. As per the site conditions required and for optimum utilisation of space for counter top to considered. Lower cabinet : Constisting 1 units of each depth 600mm, height 850mm and of lengths 2700mm which comprises the following items as shown in the drawing. 1) Top with Pull out drawers of 2 nos 1150/ 750 mm x 130/150 mm H 2) Bottom with Plain unit with fixed shutter-1550mm , 3) Hinged unit below the sink - 750mm, 3) Open unit for Cooking range - 450mm, 4) Single Hinged unit with adjustable Shelves - 500mm etc as per detailed drawings. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and as per standards, specification and directed by the Engineer-in-charge. . Mode of Measurements : Elevation area Basic Price of 1mm laminate : 80/Sft, Basic Price of 0.8mm laminate : 65/SftThe purchase price ( excluding GST ) of laminate is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/206

Providing and fixing panelling of 6mm thk Lacquered glass both sides with 19mm thick marine ply confirming to IS -710 backing in panel sizes as indicated in the drawings, with all edges machine polished and the panel fitted on to wall /partition with necessary hardwares. The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade with Adhesive /double sided tape , Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Size : 3050mmx600mm Basic Price of Lacquered glass : 190/Sft, The purchase price ( excluding GST ) of lacquered glass is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/101, AR/TD/205, AR/TD/206

Providing and Fixing of approved colour & design, Imported Vinyl backed Wall paper with recommended adhesive of approved make which have 100% washable, scratch resistance, peel proof, and fire retardant properties , Cladding on the partition wall or any recommended surface with base preparation including applying of oil base primer before application of the wall paper as per the instrutions of architect/engineer in charge. The wall paper has to be approved by the Architect/ Engineer-in-Charge before executing the work. The rate shall include all in fibre tape, proprietary make jointing compound, cutout for electrical sockets and all required materials, providing & removing of necessary scaffolding work etc. complete.As per standards, specification and directed by the Engineer-in-charge. Warrenty - 3 years after installation Basic Rate Rs. 250/ Sft The purchase price (excluding GST) of wallpaper is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted (paid extra or deducted) at the time of billing. Refer drawing AR/TD/101, AR/TD/205, AR/TD/206

Moss wall Preserved 50mm Moss Wall : Providing of Moss fixed on felt with 50mm thick moss made of 100% natural stabilised of approved color Containing Real preserved 20mm Reindeer Moss, to be used in a ratio as approved by the architect and as per final approved drawing. Installation Methodology Surface to be cladded wih 12mm Marine ply wood confirming to IS -710 with a beading of minimun 50mm depth and 25mm tickness on all 4 sides of the required surface. Installed ply wood surface to be fitted with velcro tapes as per approved shop drawings. Preserved Mosses to be pre fixed onto felt panels using suitable adhesive. Felt panels to be allowed to dry and set for minimun 7 to 10 days prior to installation. Pre set felt panels to be installed onto the fitted velcro tape as per approved design.Moss to be installed in a Dust free and AC controlled environment. No direct ligt of more than 2 Watts to be focused on the moss wall, no water or any other liquid to be sprayed or applied on the moss wall. Moss Wall is a 0 Maintenance product and is to be handled, installed and maintained by approved technician only etc complete to the requirement of EIC.The rate Inclusive of Supply of material, Fixing, Wastages,Labour Charges for Fixing & removing Scaffolding etc., complete at all levels As per standards, specification and directed by the Engineer-in-charge. Base price 8370/sft The purchase price ( excluding GST ) of moss wall is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/205, AR/TD/206

Feature Screen : Proiding , Fabricating & Installation of Vericle section consist of 'Box' shaped 1.4mm thick aluminium extruded section , The size of the 'Box' sections shall be 75mm wide 50mm D and height as per drawing with centre to centre of 75mm distance (which can be modified as per architect/designers requirement). All 4 sides of the screen shall be fixed with box sections of size 75mmx50mm, 1.5~2mm thick having flanges at each support at ceiling and at floor level with proper fixing arrangement using appropriate base plates, anchor bolts, etc.. Rate to includes necessary supports as per vendor details. The ceiling and the accessories are provided with powder coated of Approved shade ,thickness of 70-80 microns.The rate in inclusive of with necessary hardwares , required supports , Material, Labour, Scaffolding, making cut out for lights etc., complete at all levels As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/201

Providing and fixing the Bonded Metal panelling on framework made in 50 x 25/ 50.8 x 25.4mm, 16swg (1.626mm thick and consider the tolerance range of 1.60 ~1.65mm) aluminium tube section framework, placed at 600mm c/c in both the directions at different levels and to shapes as per the detail drawings. The aluminium sections shall be placed at 600mm c/c both ways and rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws as per the detail drawings and Project Consultants' instructions. The framework shall be cladded with 12mm thick Marine grade plywood confirming to IS -710 and finished in Bonded Metal of thickness as per manufacturer details to shape and size with grooves as per Architectural section etc., the rate inclusive of provision of Cove Material, Labour, Scaffolding, making cut out for lights & switches etc., complete at all levels as per standards, specification and directed by the Engineer-in-charge. ( Rate should be inclusive of Making samples at site ) Basic rate for Bonded Metal: 900 Rs /Sft The purchase price (excluding GST) of Bonded Metal is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/201, AR/TD/218

Under Counter Storage Unit of Size: 2560/1400 x 450 x 900mm H & Over Head Counter Storage Unit of Size: 2560/1400 x 300 x 650 mm H ,with Drawers /shelves with Openable doors: Supply, making, fixing and installation of Under Counter & Over head Storage Unit made out of 18mm thick MR grade ply wood confirming to IS -710 with 1mm thick laminate on all exposed side and 0.8mm thick laminate in side. Unit consist of Two parts as specified below. 1. Under Counter Storage Unit of Size: 2560 x 450 x 900mm H with a) Drawers 2nos & 1nos Shelve -520mm , b) Shelves with openable shutter ,4 nos of 500mm W . Under Counter Storage Unit of Size: 1400 x 450 x 900mm H with a) Shelves with openable shutter -980mm , b)Plain with openable shutter -465 mm Storage top made out of 18mm+18mm thick plywood and cladded with 20mm thick quartz (paid seperately )with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. 2. Over Head Counter Storage Unit of Size: 2560 x 300 x 650 mm H with a) Open unit with shelves -520mm , b) Shelves with openable shutter ,4 nos of 500mm W. Over Head Counter Storage Unit of Size: 1400 x 300 x 650 mm H with a) Shelves with openable shutter -980mm , b)Plain with openable shutter with adjustable shelevs -465 mm Drawer, shutter and facia should be made of 18mm thick MR grade plywood and 1mm. thick laminate outside and in side 0.8mm thick laminate on it. Edges of the MR grade plywood should be finished with 2 mm thick PVC edge bind, with lock , S.S. legs and telescopic channel and necessary aluminum profile handle Including all materials and labour etc. complete as per instruction of engineer‐in charge and consultant. Drawer unit box(500 x 450 x 150mm H) with 2 mm thick PVC bidding patti on legs with lock. And the telescopic channel should be made from 18mm MR grade plywood with 1mm outside and 0.8mm inside laminate as well as 18mm. post forming outside of shutter with auto hinges of Make. Assa abloy/ Dorma and drawer should be made from 18mm post forming laminated in the approved shade. (Make: Green Lam. Laminate code: STN 5616 urban concrete or one grade higher equivalent of approved make. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm,raised 75mm H & 50mm recessed to cladd skirting including transportation and installation.As per standards, specification and directed by the Engineer-in-charge. Basic price of 1mm laminate: Rs.120/Sft Basic price of 0.8mm laminateRs.80/Sft : The purchase price (excluding GST) of laminate is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Mode of Measurement : Elevation Area Refer drawing AR/TD/201

Providing and Fixing of approved colour & design , Impoted type Vinyl backed Wall paper with recommended adhesive of approved make which have 100% washable, scratch resistance, peel proof, and fire retardant properties , Cladding on the partition wall or any recommended surface with base preparation including applying of oil base primer before application of the wall paper as per the instrutions of architect/engineer in charge. The wall paper has to be approved by the Architect/ Engineer-in-Charge before executing the work. The rate shall include all in fibre tape, proprietary make jointing compound, cutout for electrical sockets and all required materials, providing & removing of necessary scaffolding work etc. complete. to the requirement of EIC Basic Rate Rs. 150/ SFT, The purchase price (excluding GST) of wallpaper is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/216, AR/TD/203, AR/TD/209

Storage Unit of Size: 3725 x 500 x 900mm H with shelves and with Openable shutter with adjustable shelves: Supply, making, fixing and installation of Under Counter & Over head Storage Unit made out of 18mm thick MR grade ply wood confirming to IS -710 with 1mm thick laminate on all exposed side and 0.8mm thick laminate in side. Unit consist details as specified below. 1. Storage Unit of Size: 3725 x 500 x 900mm H with a) Plain unit with shelves & openable shutter , 6nos -550mm , b) OPen Shelves ,1 nos of 550mm W . Storage top made out of 18mm+18mm thick plywood and cladded with 20mm thick Quartz with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. Shutter and facia should be made of 18mm thick MR grade plywood and 1mm. thick laminate outside and in side 0.8mm thick laminate on it. Edges of the MR grade plywood should be finished with 2 mm thick PVC edge bind, with lock , S.S. legs and telescopic channel and necessary aluminum profile handle Including all materials and labour etc. complete as per instruction of engineer‐in charge and consultant. post forming outside of shutter with auto hinges of Make. Assa abloy/ Dorma and drawer should be made from 18mm post forming laminated in the approved shade.Laminate code: STN 5616 urban concrete or one grade higher equivalent of approved make. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm,raised 75mm H & 50mm recessed to cladd skirting including transportation and installation.As per standards, specification and directed by the Engineer-in-charge. Basic price of 1mm laminate: Rs.120/Sft Basic price of 0.8mm laminateRs.80/Sft : The purchase price (excluding GST) of laminate is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Mode of Measurement : Elevation Area Refer drawing AR/TD/216

Low Storage Unit of Size: 3690 x 600 x 900mm H & Over Head Storage Unit of Size: 3690 x 600 x 1050mm H ,with Drawers /shelves with Openable doors: Supply, making, fixing and installation of Low Storage unit & Over head Storage Unit made out of 18mm thick MR grade ply wood confirming to IS -710 with 1mm thick laminate on all exposed side and 0.8mm thick laminate in side. Unit consist of Two parts as specified below. 1. Low Storage Unit of Size: 3690 x 600 x 900mm H with a) Drawers 1nos & 1nos Shelve -520mm , 3 nos , b) Plain unit with Adjustable Shelves and openable shutter ,4 nos of 520mm W . Storage top made out of 18mm+18mm thick plywood with 1mm thick laminate 2. Over Head Counter Storage Unit of Size: 3690 x 600 x 1050 mm H with a) Open unit with shelves -520mm ,3nos b) Shelves with openable shutter ,4 nos of 520mm W. Drawer, shutter and facia should be made of 18mm thick MR grade plywood and 1mm. thick laminate outside and in side 0.8mm thick laminate on it. Edges of the MR grade plywood should be finished with 2 mm thick PVC edge bind, with lock , S.S. legs and telescopic channel and necessary aluminum profile handle Including all materials and labour etc. complete as per instruction of engineer‐in charge and consultant. Drawer unit box(500 x 450 x 150mm H) with 2 mm thick PVC bidding patti on legs with lock. And the telescopic channel should be made from 18mm MR grade plywood with 1mm outside and 0.8mm inside laminate as well as 18mm. post forming outside of shutter with auto hinges of Make. Assa abloy/ Dorma and drawer should be made from 18mm post forming laminated in the approved shade. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm,raised 75mm H & 50mm recessed to cladd skirting including transportation and installation.As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Elevation Area Basic price of 1mm laminate: Rs.120/Sft Basic price of 0.8mm laminateRs.80/Sft : The purchase price (excluding GST) of laminate is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/216

Providing ,Cutting, making, fabricating , assembling , placing ,installing and fixing in position in true line and level as per drawing for Staff work stations with solid acrylic surface finish ,fulfilling all items as stated in specific requirements and specifications along with below mentioned features, finishes, units, etc. complete as specified and approved by architect at all levels. 1)"U" shape Work Station with Solid Acrylic finish : Table of total- 5,500mm L x total 600 mm W x 50mm thick facia ,with table top at 975mm ht . Table top at 975mm H to be 600 mm W made in 12mm thk marine ply confirming to IS -710, topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade by Architect on all exposed surface and bottom surface to be painted of approved colour by architect. 2) Linear Work Station with Solid Acrylic finish : Consist of 3 units , a)1st unit consist of ,Table of total- 6500mm L x total 600 mm W x 50mm thick facia and back splash of 100mm ,with table top at 975mm ht made in 12mm thk marine ply , topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade by Architect on all exposed surface and bottom surface to be painted of approved colour by architect. b) 2nd unit consist of Feature table for placing of planter at centre . Table of 3000mm L x semicicular 1350 mm W x 975 mm H facia with table top at 975mm H and back splash of 100mm , made in 12mm thk marine ply , topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade by Architect on all exposed surface and bottom surface to be painted of approved colour by architect. c) 3rd unit consist of Boxing for Planter of 770mm inside dia for placing plant and 975mm H ,made with 12mm ply with required boxing /framing as per detailed drawings . At top Ledge of 50mm thick x100mm W finished with 12mm thick solid acrylic surface and ply box inside to finish with paint of approved shade etc complete as per detailed drawing. Note : Required Ms Box (50x25x3mm )section to be Considered for supporting the table at every 950mm C/c and fixed to table with requierd hardwares and The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, MS supports to be painted with two coats of Enamel paint over a coat of approved Zinc chromate primer , making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan Area Basic Price of Solid surface : 650/Sft The purchase price (excluding GST) of is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/216, AR/TD/203, AR/TD/209

Same as above but with out ply box but with 12mm ply ply backing with 19mm ply packing with 12mm thick Acoustic panels As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs. 450/ SFT. The purchase price ( excluding GST ) of Acoustic panel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/212

Providing and fixing the 12mm thk Marine play backing confirming to IS -710 in panel sizes as indicated in the drawing and the panel fitted on to wall /partition with necessary hardwares. The 12mm thick marine grade ply confirming to Is 710 on framework made in 50 x 25/ 50.8 x 25.4mm, 16swg (1.626mm thick and consider the tolerance range of 1.60 ~1.65mm) aluminium tube section framework, placed at 600mm c/c in both the directions at different levels and to shapes as per the detail drawings. The aluminium sections shall be placed at 600mm c/c both ways and rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws as per the detail drawings . The framework shall be cladded with 12mm thk Acoustic panels / wood work grille ( paid seperately undere relevant item ) to shape and size with grooves as per Architectural drawings ,appropriate extruded aluminium "U/L" profiles with powder coated as approved shade etc complete . The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front Elevation Refer drawing AR/TD/213

The Woodworks (WW) Grille panel of nominal size 35x300x2400mm comprising 8 blades of 35x16x2376mm with on center spacing of 37.5mm fixed thru Backer of size 12x22x300mm with on center spacing of 300mm and additional end dowels at 150mm from both the edges. Ledger of 6.5x24x2400mm to be used for covering face of wall angle. WW Grille should comply with ASTM-E84: Class A and have Relative Humidity of RH70. The panels are UV coated to Natural or Carbonized shades Optional : Open edges may be covered using “Edge Caps” of 44x19x2400mm and “Blade Junction” of 66x38x2400mm to be used along the connection of two WW Grille Panels. The grid should be of 24mm wide T - section flanges Black powder coating having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm for the main runner & the Cross Tees and with a load carrying capacity of 20 Kgs/M2. Black backer clips of spring steel to be used for fixing panel to suspension system. Rate inclusive of Coordination with the technical team from the Manufacture in case any query & getting approval/certificate same from the them, Provision of necessary MEP cut-outs , Cove lights, Packing the perforation if required to make surface smooth etc.,The entire work shall be done as per design, drawings and direction of engineer in charge & Wall/ false ceiling surfaces shall be prepared to the satisfaction of the Architect, and if required shall be applied with two coats of primer and paint to the satisfaction of Architect/EIC As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/213

Providing and fixing suspended false ceiling / wall panelling - : Tectopanel Size 1200*600*12.5mm Micro perforation 3.5X3.5mm with 7.1 - 9.8% perforation and 0.85NRC : Regular Square perforation of glass fibre reinforced gypsum material, which includes providing and fixing GI perimeter channels The furring should be min. 60 mm wide at the short end joints (if wood is used; the steel furring can be min. 45 mm). The remaining furring can be 45 mm wide. of size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with help of connecting clips and in direction perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to be joined and finished so as to have a flush look with jointing compound. 1-The acoustic properties of the ceiling system are due to the perforation of the U Panel. 2 Isolation grey primer . 3 The acoustic fleece ensures the absence of cracks and serves as a smooth plaster support surface. 4 The look of theT acoustic ceiling is characterized by the especially fine structure of the acoustic plaster Picco S. The acoustic plaster is applied on the fleece in two layers.Choice of colours as required – Antistatic, renewable surface – Possibility of incorporating installations – High sound absorption surfaces. Cleaneo Technology - Air purification & Air quality.Active reduction of air pollutants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s like alcohol, aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke Air purification properties tested according to CEN standards and VDI guidelines by Fraunhof Institute for Building Physics Rate inclusive of Coordination and approval from the technical team of Aproved make & getting approval/certificate same from the them, Provision of necessary MEP cut-outs , Cove lights, insulation of miner wool behind panel, Packing the perforation if required to make surface smooth etc.,The entire work shall be done as per design, drawings and direction of engineer in charge & false ceiling surfaces shall be prepared to the satisfaction of the EIC, and shall be applied with two coats of primer and paint to the satisfaction of EIC .The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/213, AR/TD/212

Providing and fixing suspended false ceiling / Wall paneling - : Design panel Tangent perforation900X2400X12.5mm size board, Tangent perforation 4X14mm with 13.3-15.0-15.8% perforation and 0.65 NRC : Regular Tangent perforation of glass fibre reinforced gypsum material, which includes providing and fixing GI perimeter channels The furring should be min. 60 mm wide at the short end joints (if wood is used; the steel furring can be min. 45 mm). The remaining furring can be 45 mm wide. of size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with help of connecting clips and in direction perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to be joined and finished so as to have a flush look with jointing compound. Cleaneo Technology - Air purification & Air quality.Active reduction of air pollutants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s like alcohol, aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke Air purification properties tested according to CEN standards and VDI guidelines by Fraunhof Institute for Building Physics Rate inclusive of Coordination with the technical team of Approved Make in case any query & getting approval/certificate same from the them, Provision of necessary MEP cut-outs , Cove lights, Packing the perforation if required to make surface smooth etc.,The entire work shall be done as per design, drawings and direction of engineer in charge & false ceiling surfaces shall be prepared to the satisfaction of the Engineer in charge, and shall be applied with two coats of primer and paint to the satisfaction of EIC The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/213, AR/TD/212

Storage Units of size 1100 x 450 x 2450 H mm Supplying, Making and installing in position of full height storage unit made out of 19mm thick MR grade plywood confirming to IS -710 with double shutter and shelves, With 1mm thick laminate on the inside surface of the storage unit and 6mm thick lacquered glass on the external surface of the unit including on the shutter. Storage Unit consist of 2 units with Bottom unit as openable shutter of size 1100x450x2450mm H and Top with fixed unit of Size specified in drawing. All outer box frame unit and back ply are of 19mm thick MR grade ply with 6 mm thk lacquered glass of approved shade and on the inner surface of the box frame and shevles with 1.00 mm thick laminate including edge binding. Shutters are of 12mm thick MR grade ply with 6 mm thk lacquered glass of approved shade and 1mm thick laminate on the inside surface with all necessary edge binding and Cost of unit with concealed handle,ss hinges,tower bolts, shutter magnet,locks,magnetic ball catch,hinges,soft closure , suitable profile of approved shade etc and all necessary hardware of make,all complete as per drawing and detail and as per instruction of the Eingeer In Charge.Providing the 75mm high box skirting with recessed inside by 50mm for cladding of Skirting . The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front elevational area Basic Rate Rs. 190/ SFT. The purchase price ( excluding GST ) of Lacquered is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/212

Providing and fixing TV Ledge of size L of Various size , D-450 /500 mm x 40mm thick including making the ledge by combining 18mm and 12mm Marine ply confirming to IS -710 fixed at 750mm from finished floor with required supports from the wall behind . The ledge shall in the form of screws with PVC plugs into the back wall. The ledge shall finish with 12 mm thk solid acrylic surface of Approved shade and as per design details as per drawings . The rate including cladding all exposed surface & bottom with paint , materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan area Basic Rate Rs. 650/ SFT. The purchase price ( excluding GST ) of Solid acrylic surface is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/212, AR/TD/23

Storage Units of size 1200 x 450 x 3700/2450 H mm Supplying, Making and installing in position of full height storage unit made out of 19mm thick MR grade plywood confirming to IS -710 with double shutter and shelves, With 1mm thick laminate on the inside surface of the storage unit and 6mm thick lacquered glass on the external surface of the unit including on the shutter. Storage Unit consist of 2 units with Bottom unit as openable shutter of size 1200x450x2450mm H and Top with fixed unit of Size 1200x450x1250mm H. All outer box frame unit and back ply are of 19mm thick MR grade ply with 6 mm thk lacquered glass of approved shade and on the inner surface of the box frame and shevles with 1.00 mm thick laminate including edge binding. Shutters are of 12mm thick MR grade ply with 6 mm thk lacquered glass of approved shade and 1mm thick laminate on the inside surface with all necessary edge binding and Cost of unit with concealed handle,ss hinges,tower bolts, shutter magnet,locks,magnetic ball catch,hinges,soft closure ,suitable profile of approved shade etc and all necessary hardware of make,all complete as per drawing and detail and as per instruction of the EIC.Providing the 75mm high box skirting with recessed inside by 50mm for cladding of Skirting . The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all completeAs per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front elevational area Basic Rate Rs. 190/ SFT. The purchase price ( excluding GST ) of Lacquered glass is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/211

Providing and fixing the Acoustic Wall Paper of 3mm thickness as per manufacturer's sepcifications cladded on 12mm thick marine ply backing confirming to IS -710 in panel or as indicated in the drawings of Approved Shade shall be fixed on to the ply as recommanded by manufacturer and the panel fitted on to wall /partition with necessary hardwares . The 12mm thick marine grade ply on framework made in 50 x 25/ 50.8 x 25.4mm, 16swg (1.626mm thick and consider the tolerance range of 1.60 ~1.65mm) aluminium tube section framework, placed at 600mm c/c in both the directions at different levels and to shapes as per the detail drawings. The aluminium sections shall be placed at 600mm c/c both ways and rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws as per the detail drawings . The framework shall be cladded with 3mm Acoustic wall paper on 12ply with Adhesive / 3M double sided tape as per Architectural drawings with appropriate extruded aluminium "U/L" profiles with powder coated as approved shade etc complete . The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings &As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front Elevation Basic Rate Rs. 450/ SFT. The purchase price ( excluding GST ) of Acoustic wall paper is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/211

Supply, fixing and installation of frosted film on glazed patition and glass doors at locations as specified in the drawing to the detailed architectural drawing and as directed by the Engineer-In-Charge. NOTE: Only the stickered area will be measured in length and height. Gaps between the stickering will not be deducted if the gap is less than 50 mm.As per standards, specification and directed by the Engineer-in-charge. Refer drwing AR/TD/211

Providing and laying in position Acoustic Wall Paper of 3mm thickness as per manufacturer's sepcifications cladded on 12mm thick marine ply backing confirming to IS -710 ( Paid Seperately ) in panel or as indicated in the drawings of Approved Shade shall be fixed on to the ply as recommanded by manufacturer and the panel fitted on to wall /partition with necessary hardwares . The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated , with Adhesive / 3M double sided tape , Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front Elevation Basic Rate Rs. 350/ SFT. The purchase price ( excluding GST ) of Acoustic Wall Paper is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/210 AR/TD/215

Providing and fixing MR grade 4mm thick MDF and fixed(using adhessive) on existing ply backing as shown in the drawing and instructed by Architect . The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade , joints to be properly finished in fibre tape, proprietary make jointing compound, Adhesive , Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Elevation Refer Drawing AR/TD/210

Providing and fixing MR grade 4mm thick MDF and fixed(using adhessive) on existing ply backing as shown in the drawing and instructed by Architect . The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade, joints to be properly finished in fibre tape, proprietary make jointing compound, Adhesive, Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Elevation. Refer drawingAR/TD/214

Providing and fixing MR grade 9mm thick MDF and fixed(using adhessive) on existing ply backing as shown in the drawing and instructed by Architect . The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade , joints to be properly finished in fibre tape, proprietary make jointing compound, Adhesive, Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Note : Cost to Include for CNC cutting Mode of Measurement : Elevation. Refer drawingAR/TD/214

Supply, fixing and installation of 12mm thick marine grade ply confirming to IS -710 on framework made with 19mm thick ply and supported from frame structure in the ceiliing (paid seperately ) at different levels and to shapes as per the detail drawings. The frame structure made of 19mm ply shall be rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws oe as per vendor details as per the detail drawings. The framework shall be cladded with 12mm thick Marine grade plywood finished with 4 mm thick Venner thk as per design details as per drawings . Veneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat to shape and size with grooves as per Architectural drawings etc.,The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Size : 2700mm Outer dia / 1800mm Inner dia & 250mm Depth Mode of Measurement : Perimetre of Boxing x Running length in Sqm Basic Rate Rs. 220/ SFT. The purchase price ( excluding GST ) of Veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/215

Providing and fixing 12mm thick Acoustic panels with double side tape as per manufature's recommendation on 12mm thk Marine play backing in panel sizes as indicated in the drawing and the panel fitted on to wall /partition with necessary hardwares. The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade, with 3M double sided tape or Adhesive , Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.450/ SFT. The purchase price ( excluding GST ) of Acoustic panels is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/215

Providing and fixing panelling of 6mm thk Lacquered glass with 12mm thick marine ply backing confirming to IS -710 in panel sizes as indicated in the drawings, with all edges machine polished and the panel fitted on to wall /partition with necessary hardwares. The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade, with Adhesive /3M double sided tape , Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.190/ SFT. The purchase price ( excluding GST ) of Lacquered glass is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/215

Providing and fixing the 600mm depth of 12mm thick marine Ply confirming to IS -710 paneling on framework made in 50 x 25/ 50.8 x 25.4mm, 16swg (1.626mm thick and consider the tolerance range of 1.60 ~1.65mm) aluminium tube section framework, placed at 600mm c/c in both the directions at different levels and to shapes as per the detail drawings. The aluminium sections shall be placed at 600mm c/c both ways and rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws as per the detail drawings .As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/215

The frame shall be fixed with 12mm thick Acoustic panels with double side tape as per manufature's recommendation in panel sizes as indicated in the drawing and the panel fitted on to wall /partition with necessary hardwares. The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated , with 3M double sided tape or adhesive , Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.450/ SFT. The purchase price ( excluding GST ) of Acoustic panel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/215

Providing ,Cutting, making, fabricating , assembling , placing ,installing and fixing in position in true line and level as per drawing for Staff work stations with solid acrylic surface finish ,fulfilling all items as stated in specific requirements and specifications along with below mentioned features, finishes, units, etc. complete as specified and approved at all levels. 1)"U" shape Work Station with Solid Acrylic finish : Table of total- 12,500mm L x total 600 mm W x 50mm thick facia ,with table top at 975mm ht . Table top at 975mm H to be 600 mm W made in 12mm thk marine ply , topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade on all exposed surface and bottom surface to be painted of approved colour . 2) Linear Work Station with Solid Acrylic finish : Consist of 3 units , a)1st unit consist of ,Table of total- 6500mm L x total 600 mm W x 50mm thick facia and back splash of 100mm ,with table top at 975mm ht made in 12mm thk marine ply confirming to IS -710 , topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade on all exposed surface and bottom surface to be painted of approved colour by architect. b) 2nd unit consist of Feature table for placing of planter at centre . Table of 3000mm L x semicicular 1350 mm W x 975 mm H facia with table top at 975mm H and back splash of 100mm , made in 12mm thk marine ply , topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade on all exposed surface and bottom surface to be painted of approved colour . c) 3rd unit consist of Boxing for Planter of 770mm inside dia for placing plant and 975mm H ,made with 12mm ply with required boxing /framing as per detailed drawings . At top Ledge of 50mm thick x100mm W finished with 12mm thick solid acrylic surface and ply box inside to finish with paint of approved shade etc complete as per detailed drawing. Note : Required Ms Box (50x25x3mm )section to be Considered for supporting the table at every 950mm C/c and fixed to table with requierd hardwares and The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, MS supports to be painted with two coats of Enamel paint over a coat of approved Zinc chromate primer , making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. . Mode of Measurement : Plan Area Basic Rate Rs.650/ SFT. The purchase price ( excluding GST ) of Solid acrylic surfacel is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing refre drawing AR/TD/215

Providing and Fixing of approved colour & design , Impoted type Vinyl backed Wall paper with recommended adhesive of approved make which have 100% washable, scratch resistance, peel proof, and fire retardant properties , Cladding on the partition wall or any recommended surface with base preparation including applying of oil base primer before application of the wall paper as per the instrutions of engineer in charge. The wall paper has to be approved by the Engineer-in-Charge before executing the work. The rate shall include all in fibre tape, proprietary make jointing compound, cutout for electrical sockets and all required materials, providing & removing of necessary scaffolding work etc. complete. As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.450/ SFT. The purchase price ( excluding GST ) of Vinyl wall paper is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer AR/TD/201, AR/TD/203

Providing and fixing wooden rafter to be fabricated with 18/12 mm thk marine ply confirming to IS -710 and finished in 4mm thick veneer of approved shade on existing ply partition. Rafters of size 50x 25mm thk formed of 18mm and 12mm marine ply cladded with 4mm veneer to be fixed 100mm C/C . The rafters shall finish with veneer of 4mm thk as per design details as per drawings . Veneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat . including providing the cutouts required for fixing of electrical switches etc. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all completeAs per standards, specification and As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.220/ SFT. The purchase price ( excluding GST ) of Veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer AR/TD/203

Feature Circular table and Planter Box - Total Size of 2640mm Dia , Ledge at 1200mm H and Counter at 1000mm H. Consists of 1360mm inside dia for planter , 140mm Thick Wall on either side and 450mm Running Counter . Supply, making, fixing and installation of Feature table of size mentioned above having made of 19mm Marine ply confirming to IS -710 wood boxing with required frame work and as indicated below. 1. Base of planter box of size 2640mm dia and top ply at 600mm height is made of 19mm parine ply wood with boxing with required frame structure . 2. Ply Partition wall of 100 thick of along the perimeter above base of planter box at 600mm H with double side ply wood with suitable frame upto to the 1200mm from finished floor level. 3. 450MM Width of Polished Italian marble ( paid seperately )counter along the perimeter of the wall with approved shade by the architect at 1000mm H connected to the Boxing with required supports using MS brackets (finished with a coat of Zinc primer & Enamel paint) 4. Italian Polished Marble claddiing at the top of Size of width (200+150+150)mm along the perimeter of the wall with grooves etc as specified in the drawing and cladded to play with suitable adhesive.Fixing 18mm thk pre polished marble with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. 5. Inside planter exposed surface finished with 18mm thick WPC boards of plain white shade with the adhesive on to the ply. 6. Outside exposed surface to finished with 4mm thick veener or one grade higher equivalent of approved make cladded on ply and finished with melamine polish. The rate inclusive of Footrest with SS tube section with PVD coating ,75mm high from floor and recessed for Skirting, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Basic Rate of veneer Rs.120/ SFT Basic Rate of laminate Rs.80/ SFT.The purchase price ( excluding GST ) is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Mode of Measurement : Plan Area Refer drawing AR/TD/203.

Feature Running table and Planter Box - Total Size of 14,000mm L , 600mm W, 1050mm H Supply, making, fixing and installation of Feature running table of size mentioned above having made of 19mm Marine ply confirming to IS -710 wood boxing with required frame work and as indicated below. 1. Base of planter box of size 14m L x 600mm W and top ply at 450mm height is made of 19mm parine ply wood with boxing with required frame structure . 2. Ply Partition wall of 12 thick ply with 25mm MDF run along the length on both sides as shown in the drawings above base of planter box at 450mm H with frame structure using MS brackets of 50x50mm (finished with a coat of Zinc primer & Enamel paint) , connected at top & bottom and placed vertically at every 1.2m c/c upto to the 1050mm from finished floor level. 3. 25mm MDF Cladded to ply with suitable adhesive made with 12x6mm grooves at every 40mm c/c and with finished duco paint of approved shade 4. Top Ledge of 120mm W on either side made with 19mm marine ply and finished with 4mm thick veener cladded on ply and finished with Veneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat as pe the requirement by the architect . The rate inclusive of 75mm high from floor and recessed for Skirting, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.220/ SFT. The purchase price ( excluding GST ) of Veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Mode of Measurement : Running Length in plan

Feature Running table and Planter Box - Total Size of 5000mm L , Varies Width from 450/250mm , 1050mm H Supply, making, fixing and installation of Feature running table of size mentioned above having made of 19mm Marine ply confirming to IS -710 wood boxing with required frame work and as indicated below. 1. Ply Partition wall of 12 thick ply with 25mm MDF run along the length on both sides as shown in the drawings from the Floor level with frame structure using MS brackets of 50x50mm(finished with a coat of Zinc primer & Enamel paint) , connected at top & bottom and placed vertically at every 1.2m c/c upto to the 1050mm from finished floor level. 3. 25mm MDF Cladded to ply with suitable adhesive made with 12x6mm grooves at every 40mm c/c and finished with duco paint of approved shade . 4. Top Ledge at 1050mm H from floor level made of 19mm marine ply and finished with 4mm thick veener cladded on ply and finished with Veneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat as pe the requirement . The rate inclusive of 75mm high from floor and recessed for Skirting, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-chargeBasic Rate Rs.220/ SFT. The purchase price ( excluding GST ) of Veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Mode of Measurement : Running Length in plan

Supply, fixing and installation of Buffet Counter on floor with BWR grade plywood confirming to IS -710 with inside finished with 1 mm laminate, and all exposed surface finish with 4mm thick veneer . Post form shutters of BWR grade plywood with 4mm veneer in facia with grooves as specified in drawings and 1 mm laminate on backside. Bow Handle Zinc Alloy die cast with satin finish make 202mm Pitch (for Floor Unit),, 90 degree hinges with soft close for hinged doors, M10 screw type leveller with Hexagonal plastic base and all cooking, bottle pullout baskets, etc of SS 304 grade Approved make. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm, including transportation and installation. As per the site conditions required and for optimum utilisation of space for counter top to considered. Veneer Surface has to be finished with approved shade of melamine polish . Lower cabinet : Constisting 1 units of each depth 700mm, height 900mm ( bottom 775mm units with with shelves & hinged shutter top 125mm with Solid ply boxing ) and of lengths 12100mm which comprises the following items as shown in the drawing. 1) Plain unit with fixed shutter - 600mm, 2) Open Shelf Unit - 1750 mm in W and 450mm depth balance with fixed shutter , 3) Open Shelf Unit - 1800 mm in W and 450mm depth balance with fixed shutter,4) Plain unit with two shutter and adjustable shelves - 900mm, 5)Bottle pullout unit ( Normal/ soft Closing) & Dish Unit with serene channel - 900mm, 6) Plain unit with two shutter and adjustable shelves - 950mm, 7)Bottle pullout unit ( Normal/ soft Closing) -475mm, 8)Curve portion with Open Shelf of 450mm depth balance with fixed shutt - (1300+670) mm, 9)Plain unit with two shutter and adjustable shelves - 900mm, 10) Bottle pullout unit ( Normal/ soft Closing) -650mm , 10) Curve Plain unit with fixed shutter - 1200mm Note : Supplying & Fixing 18mm thk pre polished Italian marble of Grey or EQ shade , total length 12100mm and 700mm width and 125mm thick facia with back splash of 150mm height cladded with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. Basic price of Marble : 450/sft Basic Rate of veneer Rs.120/ SFT Basic Rate of laminate Rs.80/ SFT.The purchase price ( excluding GST ) is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. The rate inclusive of 75mm high from floor and 50mm recessed for Skirting, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurements : Elevation area

Supply, fixing and installation of Buffet Counter at centre on floor with BWR grade plywood confirming to IS -710 with inside finished with 1 mm laminate, and all exposed surface finish with 4mm thick veneer . Post form shutters of BWR grade plywood with 4mm veneer fumed one grade higher equivalent of approved make) in facia with grooves as specified in drawings and 1 mm laminate on backside. Bow Handle Zinc Alloy die cast with satin finish make 202mm Pitch (for Floor Unit),, 90 degree hinges with soft close for hinged doors, M10 screw type leveller with Hexagonal plastic base and all cooking, bottle pullout baskets, etc of SS 304 grade Approved make. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm, including transportation and installation. As per the site conditions required and for optimum utilisation of space for counter top to considered. Veneer Surface has to be finished with approved shade of melamine polish . Lower cabinet : Constisting 1 units of each depth 700mm, height 900mm ( bottom 775mm units with with shelves & hinged shutter top 125mm with Solid ply boxing ) and of lengths 6000 mm which comprises the following items as shown in the drawing. 1) Plain unit with fixed shutter all sides - 1500mm, 2) Open Shelf Unit both side with partition in between - 1500 mm in W and 450mm depth balance with fixed shutter , 3) Open Shelf Unit both side with partition in between - 1500 mm in W and 450mm depth balance with fixed shutter , 4) Plain unit with fixed shutter all sides - 1500mm Note : Supplying & Fixing 18mm thk pre polished Italian marble of Grey or EQ shade , total length 12100mm and 1000mm width and 125mm thick facia cladded with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish.Basic Rate Rs.450/ SFT. The purchase price ( excluding GST ) of Marble is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/215 The rate inclusive of 75mm high from floor and 50mm recessed for Skirting, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & as per standards, specification and directed by the Engineer-in-charge. Mode of Measurements : Elevation area Refer drawing AR/TD/203

Seamless Fire rated Gypsum Curved False Ceiling: Supply, fixing and installation at all height FALSE CEILING including providing & fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating 120gsm as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts to the angle hangers of 25x10x0.5mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section & perimeter channels 0.5mm thick 27mm high having flanges of 20mm & 30mm long, the perimeter of ceiling fixed to wall partition with the help of rawl plugs at 450mm centre to centre with 25 mm long drive-all screws @ 230mm interval including jointing & fixing to a flush finish of tapered & square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification & also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing & specification and direction of the Engineer in Charge but excluding the cost of painting with: i) 12.5 mm thick tapered edge fire resistant Fire rated GYPSUM BOARD CONFORMING TO IS: 2095- PART-I. The rate inclusive of all required materials, providing & removing of necessary scaffolding work, etc. complete. As per standards, specification and directed by the Engineer-in-charge. NOTE: Only false ceiling area will be measured from wall to wall. And no deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.Refer Drawing AR/TD/204

Providing and fixing panelling of 6mm thk Lacquered glass with 12mm thick marine ply backing confirming to IS -710 in panel sizes as indicated in the drawings, with all edges machine polished and the panel fitted on to wall /partition with necessary hardwares. The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade, with Adhesive /3M double sided tape , Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.190/ SFT. The purchase price ( excluding GST ) of Lacquered glass is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/204

Providing and fixing the 450mm thick Ply boxing confirming to IS -710 with 12mm thick marine grade ply on framework made in 50 x 25/ 50.8 x 25.4mm, 16swg (1.626mm thick and consider the tolerance range of 1.60 ~1.65mm) aluminium tube section framework, placed at 600mm c/c in both the directions at different levels and to shapes as per the detail drawings. The aluminium sections shall be placed at 600mm c/c both ways and rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws as per the detail drawings . The framework shall be cladded with 12mm thick Marine grade plywood and finished in 1mm thick laminate of Approved Shade to shape and size with grooves as per Architectural drawings etc., Table top is made of 12mm ply cladded with 1mm thick laminate and 6mm thick glass . The rate inclusive provision of Sand pit, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front Elevation Basic Rate Rs.80/ SFT. The purchase price ( excluding GST ) of laminate is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/204

Providing and fixing Shelves of size L 1300mm , D-300mm x 40mm thick including making the ledge by combining 18mm and 12mm Marine ply confirming to IS -710 fixed at 500mm c/c with required supports from the wall behind . The ledge shall in the form of screws with PVC plugs into the back wall. The ledge shall finish with veneer of 4mm thk as per design details as per drawings . The Veneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat including providing the cutouts required for fixing of electrical switches etc. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan Area Basic Rate Rs.220/ SFT. The purchase price ( excluding GST ) of veneer is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/218

Supply, fixing and installation of Storage Unit of Size ( 1300mmx450mmx750mm H) on floor with 19mm thick marine plywood confirming to IS -710 with inside finished with 1 mm laminate, and all exposed surface finish with 4mm thick veneer . Post form shutters of 12mm thick grade plywood with 4mm veneer in facia as specified in drawings and 1 mm laminate on backside.. Veneer Surface has to be finished with approved shade of PU polish , including with necessary hardware and accessories like conceald handles , hinges etc with all tools , labour , providing & removing scaffolding ,etc all complete as per the specification and design drawing and as instructed by the Engineer-in-Charge. Note : Shop drawings to Produce before production. Lower cabinet : Constisting 1 units of each depth450mm, height 750mm and of lengths 1300 mm which comprises the following items as shown in the drawing. 1. Plain unit with shutter and adjustable glass Shelves -425mm 2. Plain unit with glass adjustable shelve, 3. plain unit with shutter and adjustable glass Shelves -425mm Note : Supplying & Fixing 18mm thk pre polished Italian marble of Grey or EQ shade , total length 1300 mm width , 450mm depth and 40mm Thick facia , cladded with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. Basic price of marble : 450/sftVeneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat , Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurements : Elevation area Basic Rate of veneer Rs.220/ SFT. Basic Rate of laminate Rs.120/ SFT.The purchase price ( excluding GST ) is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer Drawing AR/TD/218

Bar Counter table - Total Size of 10100mm L , Ledge at 750 mm H is 600mm W and Counter at 1000mm H is 475mm W . Supply, fixing and installation of Bar Counter on floor with Marine grade plywood confirming to IS -710 with inside finished with 1 mm laminate, and all exposed surface finish with 6mm thick bronze . Post form shutters of 19mm thick Marine grade plywood with 4mm veneer as specified in drawings and 1 mm laminate on backside. Bow Handle Zinc Alloy die cast with satin finish make 202mm Pitch (for Floor Unit),, 90 degree hinges with soft close for hinged doors, M10 screw type leveller with Hexagonal plastic base etc of SS 304 grade Approved make. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm, including transportation and installation. As per the site conditions required and for optimum utilisation of space for counter top to considered. Veneer Surface has to be finished with approved shade of PU coat . Lower cabinet : Constisting 1 units of each depth 600mm, Ledge at 750 height have 600mm W and Counter at 1000mm height have 475mm W and of lengths 10150 mm which comprises the following items as shown in the drawing. 1) Centre Portion 4500mm L consist of a) 2nos of drawers -560mm b) plain unit with hinged door and adjustable shelves -1125mm , c) 3nos of drawers - 565mm , 2nos d)plain unit with hinged door and adjustable shelves -1125mm , e)2nos of drawers -560mm. 2) Cruve Portion of 2800mm on one side with a) Fixed Unit 550mm b ) Plain unit with opening-900mm c) Plain unit with adjustable Shelves - 1350mm 3) Curve Portion of 2800mm on other side with a) Fixed Unit 550mm b ) Plain unit with opening-900mm c) Plain unit with adjustable Shelves - 1350mm 4) Counter at 1000mm made of 150 ply boxing from floor level with required frame work and frame work of 50mmx425mm for counter at 1000mm , Italian marble of brown shade to clad at the top of 475mm & inside facia of 75mm and outside facia of 75mm with fluted details with marble throught lenth of counter. Exposed surface/outside suraface shall be caldded with 6mm thick bronze mirror in the form of square pieces with edge finish as per drawing and 15mmx15mm brush bronze metal slates cladded at every 135mm c/c . basic price of marble : 450/sft 5) Ledge at 750mm consists of 600mm W ,talian marble of brown shade to clad at the top of 600 mm & inside facia of 50mm throught lenth of counter. Note : Supplying & Fixing 18mm thk pre polished Italian marble of brown shade or EQ shade , cladded with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. The rate inclusive of Footrest with SS tube section with PVD coating , 75mm high from floor and 50mm recessed for Skirting, finishing the joints ,Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurements : Elevation area Basic Rate Rs.220/ SFT. Basic Rate of laminate Rs.80/ SFT.The purchase price ( excluding GST ) is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing.Refer drawing AR/TD/218

Seating Counter table - Total Size of 5000mm L , Ledge at 1000mm H with Counter 550mm W . Supply, fixing and installation of Seating Counter on floor with 19 mm thick Marine grade plywood confirming to IS -710 with all exposed surface finish with 6mm thick bronze mirror and 1 mm laminate on backside. Complete as per the approved color, dimensions, shapes and attached detailed specification with overall allowable tolerance ranging from Length 100-150mm, Height 15-30mm and Depth 30-50mm, including transportation and installation. As per the site conditions required and for optimum utilisation of space for counter top to considered. Veneer Surface has to be finished with approved shade of PU coat . 1) Counter at 1000mm made of 150 ply boxing from floor level with required frame work and frame work of 50mmx425mm for counter at 1000mm , Italian marble of appoved. shade to clad at the top of 550mm & inside facia of 75mm and outside facia of 75mm with fluted details with marble throught lenth of counter. Exposed surface/outside suraface shall be caldded with 6mm thick bronze mirror in the form of square pieces with edge finish as per drawing and 15mmx15mm brush bronze metal slates cladded at every 135mm c/c . Note : Supplying & Fixing 18mm thk pre polished Italian marble of brown shade or EQ shade , cladded with araldite epoxy adhesive on top and sides of the counter, with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. The rate inclusive of Footrest with SS tube section with PVD coating , 75mm high from floor and 50mm recessed for Skirting, finishing the joints ,Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurements : Elevation area Basic Rate Rs.450/ SFT. Basic Rate of laminate Rs.80/ SFT.The purchase price ( excluding GST ) is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing.Refer Drawing AR/TD/218.

Providing and fixing 150mm thick Double Side 12mm thick marine grade ply confirming to IS -710 cladded with 4mm Thick MDF on framework made in 50 x 25/ 50.8 x 25.4mm, 16swg (1.626mm thick and consider the tolerance range of 1.60 ~1.65mm) aluminium tube section framework, placed at 600mm c/c in both the directions at different levels and to shapes as per the detail drawings. The aluminium sections shall be placed at 600mm c/c both ways and rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws as per the detail drawings . The framework shall be cladded with 12mm thick Marine grade plywood with 4mm MDF and finished with paint ( paid seperately ) \ to shape and size with grooves as per Architectural drawings etc.,The rate inclusive of joints to be properly finished in fibre tape, proprietary make jointing compound, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front Elevation Refer Drawing AR/TD/219

Supply, making, fixing and installation of Curved reception table of size 4400X500X750/1150 mm having counter storage unit in the center of size 2550x450x670 mm H and details are specified below 1. For the Main table unit, the top is of 19 mm double Maine grade ply confirming to IS -710 with 4mm thick Veneer for front and sides of the table with 19 mm thick ply and and finished with 4mm thick Veneer and down platform for CPU with footrest,table top with 20m thick corian finish 2. Storage unit of 2550x450x670mm H is made of 19mm marine ply with a drawer made outer box with 12 mm Marine grade ply partition with 19 mm marine grade ply shutter. Storage at the centre 1200 is made of 19mm ply with plain unit with openable shutters with adjustable shelves and balance 675mm on either side is opened . Storage unit to be finished 4mm thick veneer for all the exposed surface and internal finished with 1mm thick laminate . The rate is inclusive of Veneer Surface has to be finished with approved shade of PU finish . Veneer is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat as pe the requirement by the architect ,hardwares of approved make hinges, handle etc as per the specifications and fixing of LED lights as shown in the design drawing all complete as instructed by the Engineer-In-Charge. Rate shall be inclusive of material, labor and transportation charges making cut out for electrical, cove lights & switches etc.,complete As per standards, specification and directed by the Engineer-in-charge. Basic Rate of veneer Rs.120/ SFT Basic Rate of laminate Rs.80/ SFT.The purchase price ( excluding GST ) is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Mode of Measurement : Elevation area Refer Drawing AR/TD/219

Providing and Fixing Solid Hard wood battens of Size 40x75mm thickness for Back wall of Credenza . The Battens to be connected to the floor using suitable MS flats (40x10mm) both at the bottom & top and fixed to RCC slab at the bottom & to be fixed by proper achoring as per vendor details. The rate is inclusive Surface has to be finished with approved shade of PU finish . Battens is finished by applying ,pu coat sealer , sanding the surface and finishing with 2 coat PU ceramic / glossy / matt coat and enamel paint on mS of approved shade by the architect etc complete as per the drawing & As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/219

Providing & fixing Mirror Paneling including Marine ply paneling confirming to IS -710 made out of 12mm thick ply wood board fixed on to the wall with adequate supports from the wall. The ply shall be fixed with 6mm thick clear mirror with all sides CNC machine polish using 3M mirror tape on sides and clear neutral silicon in center and provision with suitable profiles with powercoated of approved shade . The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/219

Supply, fixing and installation of Storage Unit of Size ( 1200/1500mmx400mmx850mm H) on floor with 19mm thick marine plywood confirming to IS -710 with inside finished with 1 mm laminate, and all exposed surface finish with 4mm thick veneer . Post form shutters of 12mm thick grade plywood with 4mm veneer in facia as specified in drawings and 1 mm laminate on backside.. Veneer Surface has to be finished with approved shade of melamine polish , including with necessary hardware and accessories like conceald handles , hinges etc with all tools , labour , providing & removing scaffolding ,etc all complete as per the specification and design drawing and as instructed by the Engineer-in-Charge. Note : Shop drawings to Produce before production. Lower cabinet : Constisting 1 units of each depth400mm, height 850mm and of lengths 1500/1200 mm which comprises the following items as shown in the drawing. 1. Plain unit with shutter and adjustable Shelves divided equally as shown in the drawng The rate inclusive of 75mm high from floor and 50mm recessed for Skirting,Veneer Surface has to be finished with approved shade melamine polish , Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Basic Rate of veneer Rs.120/ SFT Basic Rate of laminate Rs.80/ SFT.The purchase price ( excluding GST ) is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Mode of Measurements : Elevation area Refer drawing AR/TD/219

Providing and fixing Shelves of size L 2600mm , D 150mm x W 500mm , Side walls to be made of 19mm marine grade ply confirming to IS -710 and ledges with 40mm thick including making the ledge by combining 18mm and 12mm Marine ply fixed at 350mm c/c with required supports from the wall behind . The ledge shall in the form of screws with PVC plugs into the back wall. The exposed surface / ledge shall finish with veneer of 4mm thk as per design details as per drawings . The veneer surface has to be finished with approved shade melamine polish including providing the cutouts required for fixing of electrical switches etc. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan Area

Providing and fixing MR grade 4mm thick MDF and fixed(using adhessive) on ply backing(paid seperately) as shown in the drawing and instructed by Architect . The Rate in inclusive of appropriate extruded aluminium "U/L" profiles with powder coated as approved shade, joints to be properly finished in fibre tape, proprietary make jointing compound, Adhesive, Material, Labour, providing & removing Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Elevation Refer Drawing AR/TD/221

Providing & fixing 6mm thick Mirror Paneling including Marine ply paneling made out of 19mm thick ply wood board fixed over Aluminium framework of 20mm X 50mm sections at approximately 600 mm c/c both ways with adequate supports from the wall. The ply shall be fixed with 6mm thick clear mirror with all sides CNC machine polish using 3M mirror tape on sides and clear neutral silicon in center. The work shall include all suitable edge profiles with powder coated of app. shade , materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and As per standards, specification and directed by the Engineer-in-charge.Refer Drawing AR/TD/221

Graphics :Supply & Installation of Wall Décor Pro, in matte finish or specified by achitect with approved artwork digitally reproduced with water-based inks certified to have no hazardous air pollutants. Self-adhesive, bubble-free installation to be done on a smooth, dust free putty surface that has a coat of oil-based primer, by Authorised Installers only. Certificate of image licence. Warranty for a period of 60 months to be submitted along with invoice. Cost to include preparation on the punned surface for receiving the Graphics as per the manufacturer specification. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.325 SFT. The purchase price ( excluding GST ) of poster is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer drawing AR/TD/221

Fluted Marble Wall with Curved Shape Partition made in BWP Plywood & MS Frame Fabricating and fixing of Feature wall of size as per details. 100 x 50mm box powder coated metal MS section structure & cladded with 19 mm thick BWP plywood confirming to IS -710 and finish with fluted marble as per details.Cost to include additional supports as per PM's instruction.Cost to include additional supports 50 x 100mm MS sections from floring as per PM's instruction. The rate inclusive of Material , labour , instalation , provding necessary scafolding & removing , painting MS frame , finishing ,polishing protection etc complete as per the drawing & As per standards, specification and directed by the Engineer-in-charge.AR/TD/201

Providing & Installation of Fluted marble of 20mm thick , Polished Marble of approved shade claddiing to the wall as per the dsign & details ,grooves etc as specified in the drawing and cladded to play with suitable adhesive.Fixing 18mm thk pre polished marble with araldite epoxy adhesive on top and sides with mitered joints. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish..The rate shall include all connectors, accessories, fastners, profiles, adhesive , seals, Eectrical, cove ligth ,materials, labours, scaffolding, leads and lifts etc. all complete as per approved shop drawings and As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.1500/ SFT. The purchase price ( excluding GST ) of Fluted marble is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer Drawing AR/TD/201

Reception Table in Curved Shape , Finished outer side from Solid Acrylic & Inner Side in Laminate, Size 4200 mm Length x 1050mm Height x 900mm Deep Work counter table top @ 750mm LVL from FFL formed of 25mm thick ply finished with 12mm thick approved solid acrylic surface as per details. Inside surface of the reception table below the work table to be finished with approved laminate of approved shade and make. The table to be supported on 50mm x 25mm aluminium Framework as per details. The table top to have grommet for necessary electrical outlets. The Front , side fascia and ledge at 1050mm of 200mm width with 75mm facia formed out of 19mm thick ply finished in approved solid acrylic surface as per detail drawings. All exposed edges shall be lipped in 2mm thick approved PVC edge binding. Storage unit of Size ( 700 x775/450x700mm H) on either side made of 19mm ply with finished with laminate from inside & exposed surface with veneer with melamine polish . Storage consist of 2 drawers and provision of CPU one and other side with hinged shutter with necessary hardwares , finger grooves installed using approved make soft-closing hinges with soft closing mechanism. The storage shall be provided with approved hardwares like, cabinet locks, tower bolts of approved . All exposed edges shall be lipped using 2mm thick approved PVC edge binding. The table to have 75 mm high x 900mm D recessed table surface formed out of 19mm thick ply finished in approved laminate. Necessary power / Data provision to be provided below table top. The rate inclusive of Footrest with SS tube section with PVD coating , Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Front Elevation Basic Rate Rs.650/ SFT. The purchase price ( excluding GST ) of Solid Acrylic is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer Drawing AR/TD/201

Fixed Seating of overall Height of 880 mm & 580 mm Deep made in Plywood with Seating Bench & Backrest & finished in Fabric & High Density Foam. Seating Bench: Fabricating and fixing of Seating Bench made of 100mm thick high density foam wrapped with approved fabric over 19mm thick ply backing confirming to IS -710 supported on 25mm dia MS legs as per vendor details & drawings. The fascia band of 40mm high of the bench seating shall be finished with approved 4mm Thick Veneer over 19mm thick plywood backing . The seat to be supported on MS powder coated rectangular legs & above supported on nylon gliders . Back Rest : Providing and fixing tapered back rest of formed out of 150mm thick at bottom and 50mm thick at top high density foam wrapped with approved fabric of approved color shade, to have wrinkle free finish fixed to the plywood base. The backrest paneling shall be installed as per drawings and to the complete the satisfaction of the EIC along with ply support as required. the rate is inclusive Material, Labour, fabric , making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Running length Refer Drawing AR/TD/201

Providing ,Cutting, making, fabricating , assembling , placing ,installing and fixing in position in true line and level as per drawing for Ledge with solid acrylic surface finish ,fulfilling all items as stated in specific requirements and specifications along with below mentioned features, finishes, units, etc. complete as specified and approved at all levels. 1)ledge n with Solid Acrylic finish : Table of total- 11000mm L x total 600 mm W x 50mm thick facia ,with table top at 975mm ht . Table top at 975mm H to be 600 mm W made in 12mm thk marine ply confirming to IS -710 , topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade on all exposed surface and bottom surface to be painted of approved colour Note : Required Ms Box (50x25x3mm )section to be Considered for supporting the table at every 950mm C/c and fixed to table with requierd hardwares and The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, MS supports to be painted with two coats of Enamel paint over a coat of approved Zinc chromate primer , making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan Area Basic Rate Rs.650/ SFT. The purchase price ( excluding GST ) of Solid Acrylic is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer Drawing AR/TD/201

Providing and Fixing of approved colour & design , Impoted type Vinyl backed Wall paper with recommended adhesive of approved make which have 100% washable, scratch resistance, peel proof, and fire retardant properties , Cladding on the partition wall or any recommended surface with base preparation including applying of oil base primer before application of the wall paper as per the instrutions of Engineer in charge. The wall paper has to be approved by the Engineer-in-Charge before executing the work. The rate shall include all in fibre tape, proprietary make jointing compound, cutout for electrical sockets and all required materials, providing & removing of necessary scaffolding work etc. complete. As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs.200/ SFT. The purchase price ( excluding GST ) of Wallpaper is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer Drawing AR/TD/201.

Providing & fixing Mirror Paneling including Marine ply paneling confirming to IS -710 made out of 18mm thick ply wood board fixed over Aluminium framework of 20mm X 50mm sections at approximately 600 mm c/c both ways with adequate supports from the wall. The ply shall be fixed with 6mm thick clear mirror with all sides CNC machine polish using 3M mirror tape on sides and clear neutral silicon in center. The work shall include Required Edge profiles with powder quoted of approved shade ,provision for cove light ,all materials, labours, scaffolding, tools & tackles, any cut-out for services, leads and lifts etc. all complete as per approved shop drawings and As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/222, AR/TD/223

Providing and fixing Vanity counter of size in various Lengths , D-600mm with front facia of 50mm made by fixing 18mm MR grade ply boxing to the toilet wall with adequate supports in form of MS bracket. Fixing 19mm corain ( paid seperately ) with araldite epoxy adhesive on top and sides of the counter, with mitered joints. making provision in the counter top for fixing counter sunk wash basin and for fixing tap. Including filling of matching colour epoxy mastic joining compound in all joints and cracks and polishing all edges and joints to a mirror polish. The work shall include all materials, labours, scaffolding, tools & tackles, any cut-out for services, MS brackets to be painted with two coats of Enamel paint over a coat of approved Zinc chromate primer, leads and lifts etc. all complete As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan area Refer Drawing AR/TD/222, AR/TD/223

Supplying ,handling & placing with 19mm of corian for counter top. The is inclusive of wasteage , protection etc complete As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan area Basic Rate Rs.450/ SFT. The purchase price ( excluding GST ) of Corian is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer Drawing AR/TD/201

Providing ,Cutting, making, fabricating , assembling , placing ,installing and fixing in position in true line and level as per drawing for Ledge with solid acrylic surface finish ,fulfilling all items as stated in specific requirements and specifications along with below mentioned features, finishes, units, etc. complete as specified and approved at all levels. 1)Counter in with Solid Acrylic finish : Table of total- L varies x total 600 mm W x 50mm thick facia ,with table top at 750mm ht . Table top at 750mm H to be 600 mm W made in 12mm thk marine ply confirming to IS -710 , topped with 12mm MDF and finished with 12mm thick solid acrylic suface of approved shade on all exposed surface and bottom surface to be painted of approved colour Note : Required Ms Box (50x25x3mm )section to be Considered for supporting the table . The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, MS supports to be painted with two coats of Enamel paint over a coat of approved Zinc chromate primer , making cut out for electrical, cove lights & switches etc., complete at all levels as per the Detailed drawings & As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement : Plan Area Basic Rate Rs.650/ SFT. The purchase price ( excluding GST ) of Solid Acrylic is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing. Refer Drawing AR/TD/201

Same as above with with Locker unit of Size :W-300mm x D-450mm x H-1800mm , Locker -3 Tier

Same as above with with Locker unit of Size :W-300mm x D-450mm x H-1800mm , Locker -4 Tier

Same as above with with Locker unit of Size :W-300mm x D-450mm x H-1800mm , Locker -6 Tier

PARTITION / PANELING WORKS Partition dry wall (160mm Thick withTwin Frame Drywall Partition System with Double Layered Gypsum Plain Board on either Side): Supply, fixing and installation of GI frame work with 12.5 mm double layer gypsum plain Boards on both sides of the framed structure without paint finish. (Overall thickness of partition 160mm) Partition from Finished flooring level till true ceiling level / MS frame work As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/101

Partition dry wall (122mm thick Drywall Partition System with Double Layered Gypsum Plain Board on either Side): Supply, fixing and installation of GI frame work with 12.5 mm double layer gypsum plain Boards on both sides of the framed structure without paint finish. (Overall thickness of partition 122mm) Partition from Finished flooring level till true ceiling level / MS frame work As per standards, specification and directed by the Engineer-in-charge . Refer Drawing AR/TD/101

Partition dry wall (122mm thick Drywall Partition System with Double Layered Plain Gypsum Board & GlasrocH board on either Side): Supply, fixing and installation of GI frame work with 12.5 mm double layer with inner layer of 12.5mm thick gypsum plain Boards and outer layer wit 12.5mm thick mold,termite resistance GlasrocH or Eq with Glass matt reinforcement & inoganic coating on surface cladded on both sides of the framed structure without paint finish. (Overall thickness of partition 122mm) Partition from Finished flooring level till true ceiling level / MS frame work . As per standards, specification and directed by the Engineer-in-charge . Refer Drawing AR/TD/101

Partition dry wall (122mm thick Drywall Partition System with Double Layered Plain Gypsum Board Outer side & Inner side with Gypsum plain board + GlasrocH board):Supply, fixing and installation of GI frame work with12.5 mm thick thick gypsum Plain(conforming to IS 2095 Part 1:2011, ISI Certified board) and outer layer of tapered edge 12.5 mm thick thick mold and termite resistant GlasrocH or Eq with Glass mat reinforcement & inorganic coating on surface, conforming to EN 15283-1 Type GM - FH1, on WET side and double layer of tapered edge 12.5 mm thick thick Plain(conforming to IS 2095 Part 1:2011, ISI Certified board) of size 1219x2438 mm on DRY side of the framed structure without paint finish. (Overall thickness of partition 122mm) Partition from Finished flooring level till true ceiling level / MS frame work . As per standards, specification and directed by the Engineer-in-charge . Refer Drawing AR/TD/101

Partition dry wall (97mm thick Drywall Partition System with Single Layered GlasrocH towards wet & Plain Gysum Board towards dry):Supply, fixing and installation of GI frame work with 12.5 mm double layer with Outer layer of 12.5mm thick gypsum plain Boards , Dry side and Inner layer wit 12.5mm thick mold,termite resistance GlasrocH or Eq with Glass matt reinforcement & inoganic coating on surface cladded on both sides of the framed structure without paint finish. (Overall thickness of partition 122mm) Partition from Finished flooring level till true ceiling level / MS frame work . As per standards, specification and directed by the Engineer-in-charge . Refer Drawing AR/TD/101

Partition dry wall Lining (Ledgewall 170mm thick Drywall Partition System with GlasrocH Board towards inside toilet side): Supply, fixing and installation of 12.5mm thick mold,termite resistance GlasrocH or Eq with Glass matt reinforcement & inorganic coating on surface cladded inside of the framed structure without paint finish. (Overall thickness of partition 170 mm thick ledge wall ) Partition from Finished flooring level till true ceiling level / MS frame work . As per standards, specification and directed by the Engineer-in-charge . Refer Drawing AR/TD/101

Providing and fixing the 75mm thick ply paneling with 12mm thick marine grade ply confirming to IS -710 both side of the frame on framework made in 50 x 25/ 50.8 x 25.4mm, 16swg (1.626mm thick and consider the tolerance range of 1.60 ~1.65mm) aluminium tube section framework connected to MS frame work in the ceiling ( paid seperately), placed at 600mm c/c in both the directions at different levels and to shapes as per the detail drawings. The aluminium sections shall be placed at 600mm c/c both ways and rigidly connected together using 3mm thick aluminium L- cleats fixed/ fastened to aluminium section with double screws as per the detail drawings . The framework shall be cladded with 12mm thick Marine grade plywood on both side of the frame and finished Veneer /Laminate/Wall paper /MDF ( Paid seperately under relevant item ) to shape and size with grooves as per Architectural drawings etc., .The rate inclusive of fibre tape, proprietary make jointing compound, flexi ply at curve portion, Material, Labour, providing & removing necessary Scaffolding, making cut out for electrical, cove lights & switches etc., complete at all levels As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/101 Mode of Measurement : Wall to Wall

Supply, fixing and installation in position 75 mm thick partition with 12.5 mm thick single layer gypsum board on the both the faces of the partition over the false ceiling level up to true ceiling / MS frame structure .As per standards, specification and directed by the Engineer-in-charge . Refer Drawing AR/TD/101

Supply, fixing and installation of tested 120 minutes fire rated - fully glazed non-load bearing fixed partition system. The glass should be 12thick mm clear 120 min fire rated, Non Wired Toughened glass having a sound reduction of >37dB, LT of 86%. The glass should be fire rated and manufacturer to provide the certification for the same. The glass should be held in its place with the help of minimum 1.60 mm GI beading which can be clamped or bolted to the profile by 4 mm x 35 mm steel screws at every 300 mm c/c and a ceramic tape of the cross section of 5 mm x 20 mm as per the test evidence. The glass should be installed using a ceramic tape. The glass panes are to be supported on non combustible 5 mm Calcium Silicate setting blocks. The maximum glazing size cannot be more than 1100 mm x 2200 mm (w x h) or 2.42 sqmts in total area. The rate shall include all connectors, accessories, fastners, profiles, adhesive tapes, seals, making necessary opening and accessories for Electrical/Data/Voice switches and sockets and all required materials, providing & removing of necessary scaffolding work etc. complete. As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/101. Mode of Measurement : Only partition area will be measured from end to end for payment

Supply, fixing and installation of non load bearing fixed frame for fire resistant glazed Partition of 12mm thick clear for 120 minutes Fire Rating, made out to a profile of dimension 60mm x 70 mm of 1.6 mm thick galvanised steel sheet as per test evidence suitable for fixing fire rated glass for 120 minutes of both integrity & radiation control (EW120) & minimum 20 minutes of insulation (EI20).The profile has to be fixed to the supporting construction by means of anchor fasteners of size M10 x 80, every 150 mm from the edges and every 500 mm (approx) c/c. The frame shall be filled with mineral wool insulation of density min 96kg/ m³ and finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer - in- charge. The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, complete at all levels As per standards, specification and directed by the Engineer-in-charge. Mode of Measurement :Linear measurement of frame shall be measured for payment.

Supply, fixing and installation of non load bearing fixed Cuved fire resistant glazed Partition of 12mm thick clear for 120 minutes Fire Rating, made out to a profile of dimension 60mm x 70 mm of 1.6 mm thick galvanised steel sheet as per test evidence suitable for fixing fire rated glass for 120 minutes of both integrity & radiation control (EW120) & minimum 20 minutes of insulation (EI20).The profile has to be fixed to the supporting construction by means of anchor fasteners of size M10 x 80, every 150 mm from the edges and every 500 mm (approx) c/c. The frame shall be filled with mineral wool insulation of density min 96kg/ m³ and finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer - in- charge. The rate inclusive of Material, Labour, providing & removing necessary Scaffolding, complete at all levels As per standards, specification and directed by the Engineer-in-charge. Refer drawing AR/TD/101. Mode of Measurement : Curved measurement in plan, end to end shall be measured for payment.

Supply and Installation of Full height Extruted Aluminium Glazed partitions system of 100x45 mm thick section or as per Manufacture details for partitions Using section as verticles at the soild partion junction & sections of 50x33 thick or as per Manufactures details for Horizontals at Top & Bottom for Installing glass . The rate including of 25mm wide vertical , Horizontals & Intermediates at equal intervals as specified in drawings using sections 2nos of size required both the sides of the glass , Frame shall be finished powder coated (50-60 microns)of approved shade as per selction of EIC, cost of 12m m thick LaminatedToughened glass with double sided adhesive tapes for glass to glass butt joints etc , as per Design & drawings,material, Labour & wastages & Scaffolding Complete at all level As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/101. Mode of Measurement : Only partition area will be measured from end to end for payment

Supply and Installation of Full height Extruted Aluminium Curved Glazed partitions system of 100x45 mm thick section or as per Manufacture details for partitions Using section as verticles at the soild partion junction & sections of 50x33 thick or as per Manufactures details for Horizontals at Top & Bottom for Installing glass . The rate including of 25mm wide vertical , Horizontals & Intermediates at equal intervals as specified in drawings using sections 2nos of size required both the sides of the glass , Frame shall be finished powder coated (50-60 microns)of approved shade , cost of 12m thick LaminatedToughened glass with double sided adhesive tapes for glass to glass butt joints etc , as per Design & drawings,material, Labour & wastages & Scaffolding Complete at all level As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/101. Mode of Measurement : Curved measurement in plan, end to end shall be measured for payment.

Supply and Installation of Full height Extruted Aluminium Fluted Glazed partitions system of 100x45 mm thick section or as per Manufacture details for partitions Using section as verticles at the soild partion junction & sections of 50x33 thick or as per Manufactures details for Horizontals at Top & Bottom for Installing glass . The rate including of 25mm wide vertical , Horizontals & Intermediates at equal intervals as specified in drawings using sections 2nos of size required both the sides of the glass , Frame shall be finished powder coated (50-60 microns)of approved shade , cost of 10mm thick Laminated Toughened glass with double sided adhesive tapes for glass to glass butt joints etc , as per Design & drawings,material, Labour & wastages & Scaffolding Complete at all level As per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/101. Mode of Measurement : Only partition area will be measured from end to end for payment

Providing and fixing of Rest room (urinal partitions) with 10 mm thick frosted safety glass and fixed to the walls with suitable chrome finished Clamps as per manufacture's details . The rate is including all necessary hardware, fittings, material, labour, tools, lead, lift, scaffolding, all site arrangements, protection till final finish & handover, complete in all respects. Dimensions: depth 450 mm, Total Height 1200mmAs per standards, specification and directed by the Engineer-in-charge. Refer Drawing AR/TD/222,AR/TD/223.AR/TD/224.AR/TD/225.

Same as above but Toilet cubicle of Size upto (H-1950/2100mm x D-1525/1600mm x W-925/1000mm) with 600mm door Size in width - L Shape

Providing & fixing in position of 12mm thk. clear toughened glass partition as per drawing, Including SS 304 grade "C" channel on floor, wall and ceiling with Silicone Sealant & rubber seal, glass to be fixed in "C" channel all around as per detail, including making required groove in wall cladding to insert channel, also including making holes in glass for hinges etc., including all necessary hardware, fittings, material, labour, tools, lead, lift, scaffolding, all site arrangements, protection till final finish & handover, complete in all respects.As per standards, specification and directed by the Engineer-in-charge.

ROOFING WORK Providing, fabricating, erecting and fixing in position self supporting decking sheet of specified make and thickness, supported on girders, including necessary fixtures, hardwares, anchor bolts, necessary overlapping, side support as per drawings and and specifications etc., complete at all levels and location, including all materials, machineries, manpower, loading and unloading, packing pockets wherever required. The item shall even cover the edge form, steel racket, etc. completed. Method of measurement shall be plan area. The rate include supply and fixing of shear studs @ 500mm c/c in to the girders and corrugated deck sheets as specified, including high strength fusion welding, all materials, machineries, manpower, loading, unloading, packing pockets wherever required etc. complete as per specifications, drawings and As per standards, specification and directed by the Engineer-in-charge. . Decking sheet - 1.00mm thick.

Providing and laying Mangalore tiles of size 320mm or nearest with Class A Mangalore patter tiles of approved make over the cement mortar reeper bands already done to correct lines and levels including the cost, conveyance of all matenals, labour charges,lead, lift etc complete As per standards, specification and directed by the Engineer-in-charge. at all levels.(cost of cement mortar reeper bands will be paid seperately)(The purchase price considered for MP tile is Rs.55/- per tile and any deviation plus or minus in the purchase price will be adjusted in the price quoted).

Providing and laying Mangalor tiles hip and ridge tiles with class A Mangalore pattem tiles of approved make including fixing with cement mortar 1:2 (1 cement: 2 coarse sand) As per standards, specification and directed by the Engineer-in-charge. (The purchase price considered for MP tile is Rs.80/- per tile and any deviation plus or minus in the purchase price will be adjusted in the price quoted).

PAINTING WORKS Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colourAs per standards, specification and directed by the Engineer-in-charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.As per standards, specification and directed by the Engineer-in-charge.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. (for internal wall) As per standards, specification and directed by the Engineer-in-charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. For Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture (for ceiling/wall area)As per standards, specification and directed by the Engineer-in-charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including water thinnable priming coat with cement primer As per standards, specification and directed by the Engineer-in-charge.

White washing with lime to give an even shade (for Ducts) New work (three or more coats) As per standards, specification and directed by the Engineer-in-charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm (for External Walls)As per standards, specification and directed by the Engineer-in-charge.

Supply and application of Duco paint of approved color and make on MR grade Plywood/ exterior grade MDF partition wall and complete as per the detailed drawing or the instructions of the Engineer-in-Charge including applying of primer (3-5 DFT), putty work, with preparation of surface ready for applying DUCO paint. The cost shall be inclusive of preparing the surface, applying primer, putty, necessary staging/ scaffolding etc. complete.As per standards, specification and directed by the Engineer-in-charge.

Supply and application of Decorative paint / Texture paint of approed make on Partion walls/ Plastered walls / RC surface to be applied as directed by Engineer-in-Charge including preparing the surface, providing and applying one coat of water base primer of approved make and two coat of water base acrylic putty approved make, sanding, light sanding, scaffolding, work platform, painting equipment / apparatus etc. required to complete Interior grade finish with 3 coats of approved shade colour etc. complete As per standards, specification and directed by the Engineer-in-charge.

Supply and application of Decorative paint / Texture paint of make Asian/ Berger/ Duluxe for Partion walls/ Plastered walls / RC surface to be applied as directed by Engineer-in-Charge including preparing the surface, providing and applying one coat of water base primer of approved make and two coat of water base acrylic putty approved make, sanding, light sanding, scaffolding, work platform, painting equipment / apparatus etc. required to complete Interior grade finish with 3 coats of approved shade colour etc. complete As per standards, specification and directed by the Engineer-in-charge.

Painting steelwork with two or more coats of Synthetic enamel paint of Ist quality and approved colour to give an even shade over two coats of zinc rich apoxy primer (70 micron) including, filling the joint welding with metal Paste and cleaning the surfaces, Working platfrom/scaffolding & the DFT test of primer & paint etc; complete all as per specifications (Rate to include cost of zinc chromate primer also). Complete at all levels and As per standards, specification and directed by the Engineer-in-charge.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. on concrete workAs per standards, specification and directed by the Engineer-in-charge.

WATER PROOFING WORKS Supplying and installing a 4 layer MasterSeal 730 UVS of make MBS - 1.2mm thick (with HDPE thickness of 0.9mm) , Pressure sensitive adhesive & UV stable non tacky protective coating and a HDPE Release liner based waterproofing Membrane for Substructure by using before casting of the base RCC slab and shall conform to all grades of basement as defined in IS 16471. The pre-applied membrane shall be installed with standard 75/80mm selvedge laps and 80mm end laps taped with UVS a double side coated adhesive tape over the entire area and turned up on to removable formwork and stopped 50mm below the thickness of concrete slab. The membrane shall be laid over the concrete blinding having smooth dried surface, necessary overlaps between the membranes and fixing overlaps by Tape, firm rolling onto the surface to get a tight seal, etc. strictly following manufacturer's instruction and complete. Note : to execute the waterproofing work the site water table shall be maintained low Under Contractors ScopeThe fully bonded HDPE sheet waterproofing membrane shall have following typical properties (Approval on third party international & datasheet & MTC submission with key properties) : 1) Elongation at break (ASTM D 412) min 500% 2) Tensile Strength (ASTM D 412) shall be min. 25MPa. 3) Puncture Resistance as per ASTM E154 (modified) shall be Min. 1000N 4) Peel adhesion to concrete as per ASTM D903: 1998( 2017) shall be >1.8N/mm and after heat aged surface @70°C for 14days :>1.5N/mm 5) UV Accelerated Weathering (1000Hrs)or 41 Days 6) Lap Peel Adhesion to HDPE Sheet 23deg & 4deg : >0.8N/mm 7) Resistance to Hydrostatic Head (m) ASTM D 5385 modified : 71m All systems to be installed as per manufacturer's recommendations, etc. complete with all lead and lift for all materials and labour and as directed by Engineer in-charge.

Surface preparation : Preparing the surface to remove all loose matter, minor repair, honeycombed area and treat construction joints with non-shrink fibre reinforced mortar with approved chemical Waterproof coating: Providing mixing and applying a two component acrylic reinforced cementitious waterproof coating, is supplied in premeasured units and should be mixed on site utilising clean containers ((NO ADDITION WATER FOR MIXING)). Slowly add the powder to the liquid and mix, using a slow speed (300rpm) drill fitted with a suitable paddle and applied on the prepared surface in two coats at an interval of 4 to 8 hours between coats, depending on the climatic conditions, applied at a total consumption of 3.6 kg / m² at 2 mm thickness (1.8kg/sq.m/mm) and allowed to cure. The second coat shall be sprinkled / Broadcast with sand while in tacky state to provide bond, all complete as per the instruction of manufacturer and as directed by the engineer incharge. Waterproofing shall have following performance property Elongation upto 40% (28 days curing)Water penetration resistance @ 5 Bar as per DIN 1048 - NIL, all complete as per the instruction of manufacturer and As per standards, specification and directed by the Engineer-in-charge.

Protection layer to Slope : Providing, batching, mixing, transporting through transit mixers, pumping and laying controlled Screed Concrete of M20 grade at all levels and heights specified below using pozzolana Portland cement of grade 53 from approved manufacturer, sand, 12mm and down size coarse aggregates, including all leads and lifts, pumping using line pump or boom placer, vibrating/ compaction, curing as directed at all heights and depths as instructed.As per standards, specification and directed by the Engineer-in-charge.

Protective Plaster: Providing and laying protective plaster with cement mortar of ratio 1:4 mixed with integral waterproofing additive at a dosage of 100ml per bag of cement and shall be applied for a thickness of 15mm, on the waterproof coating on the floor and the wall etc., to provide protection to the coating system and cured as per standard practice Note: Rate quoted is for items a to d but required cement and sand have to be supplied free of cost at site. As per standards, specification and directed by the Engineer-in-charge.

Providing and applying solvent free , 98-100% solids, two component, instant setting, Polyurethane hybrid spray applied waterproofing system of make Waterproofing membrane shall be free of bituminous, laid coving all areas in horizontal and vertical face covering every possible area at min 1.8mm total average DFT to be applied at minimum consumption of min 2.0kg per sqm incl. wastage . I/c applying moisture insensitive epoxy primer, two component epoxy primer and broadcasted with sand using 0.3-0.9mm gradation, directly followed by applying waterproofing membrane using specialized 2 component hot spray machine as per approved manufactures specifications. • The mixed product should have 98-100% solid content as per DIN 53213. • Tensile strength 8 Mpa as per DIN 53504 • Elongation > 400% DIN 54504 • Instant setting Within 15 to 20 sec and green label. • Crack bridging 5mm as per ASTM D 412 • Water Vapor Permeability (4.0mm, 23°C /75%r.h.) (EN ISO 7783-1) : 3.6 g/(sqm d). • Shore A hardness :75 ±5 • Dynamic crack bridging capability (static A5 at 23℃ (>2.5mm), Dynamic B4.2 at 23℃ (crack width from 0.2 to 0.5mm 1,00,000 cycles as a trapezoidal function using 0.03Hz, superimposed crack cycles as sinus function using 1HZ according to EN 1504-2, EN1062-7) • Root Resistance as per DIN 4062 As per standards, specification and directed by the Engineer-in-charge.

Protection layer to Slope : Providing, batching, mixing, transporting through transit mixers, pumping and laying controlled Screed Concrete of M20 grade at all levels and heights specified below using pozzolana Portland cement of grade 53 from approved manufacturer, sand, 12mm and down size coarse aggregates, including all leads and lifts, pumping using line pump or boom placer, vibrating/ compaction, curing as directed at all heights and depths as instructed. As per standards, specification and directed by the Engineer-in-charge.

BORE PACKING Upto 75mm Dia: The surface of the cut out hole and the pipe shall be thoroughly prepared to ensure the removal loose particles and dust etc. including abrading the pipe outer surface to ensure proper bond to the filling materials. It should be ensured that the annular space around the pipe should be of minimum 20mm to allow free flow of and proper filling with non shrink grout material. The surface has to be pre-wet with water before the application of filling material. Providing and applying waterproofing treatment by fixing slurry tight shuttering below and the annular space shall be filled to half depth with Solutions a non shrink cementitious grout and allowed to harden and then a 10mm bead, a hydro-swellabe waterstop in paste form available in Catridge shall be squeezed out and applied around the pipe at half the depth level and allowed to harden. Subsequently the remaining half shall be filled with allowed to cure etc., all complete as per the manufacturer's instruction and As per standards, specification and directed by the Engineer-in-charge. Note: If the annular space between pipe and concrete is less than 20mm then suitable epoxy grout has to be used to fill the gap. Rate should include cost of materials and labour for application, including conveyance, lead and lift etc.,

BORE PACKING Upto 110mm Dia: The surface of the cut out hole and the pipe shall be thoroughly prepared to ensure the removal loose particles and dust etc. including abrading the pipe outer surface to ensure proper bond to the filling materials. It should be ensured that the annular space around the pipe should be of minimum 20mm to allow free flow of and proper filling with non shrink grout material. The surface has to be pre-wet with water before the application of filling material. Providing and applying waterproofing treatment by fixing slurry tight shuttering below and the annular space shall be filled to half depth with Solutions a non shrink cementitious grout and allowed to harden and then a 10mm bead, a hydro-swellabe waterstop in paste form available in Catridge shall be squeezed out and applied around the pipe at half the depth level and allowed to harden. Subsequently the remaining half shall be filled with allowed to cure etc., all complete as per the manufacturer's instruction and As per standards, specification and directed by the Engineer-in-charge. Note: If the annular space between pipe and concrete is less than 20mm then suitable epoxy grout has to be used to fill the gap. Rate should include cost of materials and labour for application, including conveyance, lead and lift etc.,

BORE PACKING Upto 150-200mm Dia: The surface of the cut out hole and the pipe shall be thoroughly prepared to ensure the removal loose particles and dust etc. including abrading the pipe outer surface to ensure proper bond to the filling materials. It should be ensured that the annular space around the pipe should be of minimum 20mm to allow free flow of and proper filling with non shrink grout material. The surface has to be pre-wet with water before the application of filling material. Providing and applying waterproofing treatment by fixing slurry tight shuttering below and the annular space shall be filled to half depth with Solutions a non shrink cementitious grout and allowed to harden and then a 10mm bead, a hydro-swellabe waterstop in paste form available in Catridge shall be squeezed out and applied around the pipe at half the depth level and allowed to harden. Subsequently the remaining half shall be filled with allowed to cure etc., all complete as per the manufacturer's instruction and As per standards, specification and directed by the Engineer-in-charge. Note: If the annular space between pipe and concrete is less than 20mm then suitable epoxy grout has to be used to fill the gap. Rate should include cost of materials and labour for application, including conveyance, lead and lift etc.,

Surface preparation: The surface shall be cleaned to ensure the removal of all dust, dirt, Porous substrates shall be coated with a water based acrylilc primer equivalent in one full coat and allowed dry for 1 to 2 hours before the application of waterproof coating. Waterproof coating: Providing and applying two coats of a single component, flexible, solvent free, polymer mastic waterproofing coating which shall be free of bitumen or coal tar of make equivalent and applied on the prepared surface in two coats at an interval of 2 hours between coats, at a consumption of 1kg/Sq.m/coat to achieve a total dry fill thickness of 1mm and allowed to cure and vertical surface upto 500mm height Providing and applying Special waterproof fleece-lined rubber tape with non-woven backing laid along the corners and wall to wall and wall to floor junctions sandwiched between the first and second coat of waterproof coating. Providing and applying Special waterproof Laid around pipe culverts, sandwiched between the first and second coat of waterproof coating. As per standards, specification and directed by the Engineer-in-charge. Note: Rate quoted is for items a to b but required cement and sand have to be supplied free of cost at site.

Surface preparation : Preparing the surface to remove all loose matter, minor repair, honeycombed area and treat construction joints with non-shrink fibre reinforced mortar.Waterpriming is required before the commencement of the Waterproofing coating, Waterproof coating: Providing mixing and applying a two component acrylic reinforced cementitious waterproof coating, is supplied in premeasured units and should be mixed on site utilising clean containers. Slowly add the powder to the liquid and mix, using a slow speed (300rpm) drill fitted with a suitable paddle and applied on the prepared surface in two coats at an interval of 4 to 8 hours between coats, depending on the climatic conditions, applied at a total consumption of 3.6 kg / m² at 2 mm thickness(1.8kg/sq.m/mm) and allowed to cure. The second coat shall be sprinkled / Broadcast with sand while in tacky state to provide bond, all complete as per the instruction of manufacturer and as directed by the engineer incharge. Waterproofing shall have following performance property Elongation upto 40% (28 days curing) Water penetration resistance @ 5 Bar as per DIN 1048 - NIL, all complete as per the instruction of manufacturer and As per standards, specification and directed by the Engineer-in-charge.

DISMANTLING & DEMOLITION WORKS Demolishing cement concrete manually/ by mechanical means including disposal of material upto 5Kms lead of Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) As per standards, specification and directed by the Engineer-in-charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material upto 5Kms lead As per standards, specification and directed by the Engineer-in-charge.

Demolishing brick work In cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material upto 5Kms lead As per standards, specification and directed by the Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking upto 5Kms lead :Of area 3 sq. metres and below As per standards, specification and directed by the Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking upto 5Kms lead :Of area beyond 3 sq. metres As per standards, specification and directed by the Engineer-in-charge.

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material upto 5Kms lead : sectional area 40 square centimetres and above As per standards, specification and directed by the Engineer-in-charge.

Dismantling MS & SS Steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking upto 5Kms. As per standards, specification and directed by the Engineer-in-charge.

Dismantling tile work in floors/Walls and roofs laid in cement mortar including stacking material upto 5Kms lead.For thickness of tiles 10 mm to 25 mm As per standards, specification and directed by the Engineer-in-charge.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material upto 5Kms As per standards, specification and directed by the Engineer-in-charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping groundupto 5Kms lead. As per standards, specification and directed by the Engineer-in-charge.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing,fabrics and false ceiling including disposal of unserviceable material and stacking of serviceable material upto 5Kms lead as per standards, specification and directed by the Engineer-in-charge.

PELMET Supply, fixing and installation of marine grade Ply pelmet for ceiling 200 mm thick and 150mm depth with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete as per the specification and design drawing and as per standards, specification and directed by the Engineer-in-charge.

Supply, making and fixing of Soft Board with 12 mm thick ply backing and edge binding on the edges of 12 mm ply and fixing the same over the partition wall/ masonry wall/ RCC wall etc. with all necessary fixtures and fasteners, above the table, workstations etc. as per the instruction of Engineer-in-Charge. The rate is inclusive of all material, labor, transport , hardwares etc. complete.As per standards, specification and directed by the Engineer-in-charge.

Miscelleneous Providing, supplying & installing wicker Boats as per the Vendors details from the frame structure in the ceiling. Etc complete As per standards, specification and directed by the Engineer-in-charge.

Providing & Installtion of Modular floor aluminium matting of 14.5mm thick approved make & shade made of with low lustre anodised with the inserts suitable for indoor & outdoor areas . The floor mats should be installed in recessed -well areas and normal flooring with with edging , specially designed for high foot & trolley traffic . The carpet meets the requirements of BS 7976-2 with slip resistence and it should be Moisture resistance, Fire rated, proper Impact Sound insulation, best quality of sound absorption, Thermal resistance & anti static etc., Complete at all levels. the rate inclusive of material, Labour charges for Laying & wastages etc.,As per standards, specification and directed by the Engineer-in-charge. Basic Rate Rs. 1600/ SFT. The purchase price ( excluding GST ) of Acoustic Wall Paper is mentioned in basic price and any deviation plus or minus in the purchase price will be adjusted ( paid extra or deducted ) at the time of billing.

Description of Work / Item(s)

Amount

Supply of IP based POE enabled 5MP Indoor Dome type Camera with 1/2.7" CMOS, Min. Illumination required 0.01 lux @ F1.4 (color), Min. 1080p, Varifocal 2.8-12 mm motorized lens, built in Smart IR with upto 30m IR distance, Multiple Stream with individual configurable. camera should be True Day/night, Motion, tamper and audio detection,WDR, Electronic shutter,White balance, BLC, Anti-flicker,Vandal proof Housing. cost shall be inclusive of necessary mounting accessories.

ITC of IP based POE enabled 5MP Indoor Dome type Camera

Supply IP based POE enabled 5MP Outdoor Bullet type Camera with 1/2.9" CMOS or better, Min. Illumination required 0.01 lux @ F1.4 (color), Min. Pixels 1920 × 1080, Varifocal 2.7-13.5 mm motorized lens, built in Smart IR with upto 30m IR distance, Multiple Stream with individual configurable. camera should be True Day/night, Motion, tamper and audio detection,WDR, Electronic shutter,White balance, BLC, Anti-flicker,Vandal proof Housing with all necessary mounting accessories complete as required.

ITC of IP based POE enabled 5MP Outdoor Bullet type Camera

Supply of 100x100mm PVC back box as required to install the CCTV cameras.

ITC of 100x100mm PVC back box as required to install the CCTV cameras.

Supply of Media converters for external CCTV cameras with all necessary accessoriers complete as required.

ITC of Media converters for external CCTV cameras with all necessary accessoriers complete as required.

Supply of 64 channel NVR suitable for CCTV camera above, with 4 SATA ports with 6TB HDD with two video HDMI viewing outputs, network throughport of upto 320 mbps. Contractor shall size the NVR for real time Full HD resolution at 25 FPS with 30 days of continuous recording and submit data sheet of their storage calculation for both MPEG 4 and H.264 recording formats. The NVR should be capable to support motion based recording, web based monitoring and remote control monitoring software with valid licenses. The software should enable the user to view multiple cameras in any combination available on the network. The storage capacity shall be for 30 days backup.

ITC of 64 channel NVR

Supply of 32 channel NVR suitable for CCTV camera above, with 4 SATA ports with 8TB HDD with two video HDMI viewing outputs, network throughport of upto 320 mbps. Contractor shall size the NVR for real time Full HD resolution at 25 FPS with 30 days of continuous recording and submit data sheet of their storage calculation for both MPEG 4 and H.264 recording formats. The NVR should be capable to support motion based recording, web based monitoring and remote control monitoring software with valid licenses. The software should enable the user to view multiple cameras in any combination available on the network. The storage capacity shall be for 30 days backup.

ITC of 32 channel NVR

ITC of HD LED screen, no less than 55" with HDMI, PC inputs.

PHYSICAL SECURITY SYSTEM Door Frame Metal Detectors Supply of Door frame type metal detector complete with the power regulator and anti interference ability. The detection of the channel from bottom to top shall be divided into six separate detection zone. It should adapts advanced chip processing technology, high sensitivity in the detection region without blind spots, detecting even very good points, directly point out metal the specific location through alarm. The metal detector shall comply to the specifications and feature as described in the technical specification. Inbuilt battery having mins backup hall be available or 1kVA online UPS (make: APC or Liebert) with min. 30 mins power backup at full load shall be supplied.

ITC of of Door frame type metal detector

Supply of Hand Held type Metal Detector, with multi colour LED lights, Alarm sounder, battery operated and battery charger kit to detect any metal objects through Alarms.

ITC of Hand Held type Metal Detector

BAGGAGE SCANNERS Supply of Bi-directional X-ray Baggage Scanner with integrated security inspection equipment to detect small pieces of cargo , parcels, mail, small bags, suitcase , bag , backpack and other objects in the hidden prohibited items such as firearms, knives, detonators,fireworks, etc complete as required. It shall also have features like Dark & Light enhancer, High/Low Density & Stripping, Multi-Energy (M) color material identification with organic and inorganic stripping, 6 colour identification, with input/output Roll out Tables & stabilizers ,Ethernet slot for remote viewing & Networking as per technical specifications. The cost shall incude PC/monitoring system suitable for viewing objects and things inside the baggage with all accessories complete as required for operation of the system. Steel Penetration - 30 mm, single wire resolution - 40 SWG, 2kVA Online UPS (make: APC or Liebert) with minimum 30 minutes power backup at full load shall be supplied

ITC of Bi-directional X-ray Baggage Scanner

GUEST ROOM SYSTEM Software Supply of Guest Room software upto 50 Reader , 2000 credentials , On-premises management solution , Compatible with EAC Hardware incl. I/O module , Compatible with wired readers, wireless locks and biometrics modules and 3rd party system integration.

ITC of Guest Room software

Supply of Radio USB Dongle & Programming Tool

ITC of Radio USB Dongle & Programming Tool

Supply of Guest Room Workstation with following configuration :- Processor : Intel core i7 , Clock frequency 3.0 GHz, Operating system : Windows 2010 ,64 bit, RAM : 8 GB, Hard drive : HDD 1 TB, DVD , USB, Mouse, keyboard etc, 24" LED screen.

ITC of Guest Room Workstation

Controllers and Wireless Hub Supply of Controller Module Wiegand with Plastic Housing Processing power to control up to 32 doors , Integrates with door lock devices , Anti-tamper switch, 8 LED diagnostic indicators, TCP/IP port, 1 dedicated RS485port for controlling wireless Hubs and for connection of remote Cluster Controllers for further expansion possibilities , stores up to 100,000 transactions internally, keeping the data safe and accessible.

ITC of Controller

Supply of Door Reader Module on IPS Back plate connecting up to two wired readers , Two 10A independent single-pole,double-throw (SPDT) relay outputs, can interface to door strikes, magnetic locks and other third-party devices, such as alarm panels or lighting.

ITC of Door Reader Module

Supply of IP based wireless communication hub to connection to Guest Room system via IP/Ethernet connection , Allows to connect up to 64 devices on a single hub , Encrypted radio communication , TCP/IP communication encrypted using TLS 1.1/1.2 , Powered using Power over Ethernet (PoE) or external power supply , For standard electrical installation boxes , LED for status visualisation, Built in tamper switch. Detection of removal from bracket, Firmware upgrade via UHF radio or IP network , Event Log in the hub.

ITC of IP based wireless communication hub

ITC of Wireless Handle door lock

Supply of Power Supply units to cater the required DC power source

ITC of Power Supply units to cater the required DC power source

Supply of 3C 1.5 sqmm ABC Power Supply cables

ITC of 3C 1.5 sqmm ABC Power Supply cables

AUDIO VIDEO SYSTEM Supply, Installation, Testing and comissioning of the following equipment for AV System Supply of 7150 ISO Lumens WUXGA 1DLP Laser projector, Fixed motorized zoom lens, 3,000,000:1 Contrast ratio, with professional AV connectivity

ITC of 7150 ISO Lumens WUXGA 1DLP Laser projector

Supply of 5000 ISO Lumens WUXGA 1DLP Ultra Short Throw Laser projector with 4-corner geometry adjustment and professional AV connectivity

ITC of 5000 ISO Lumens WUXGA 1DLP Ultra Short Throw Laser projector

Supply of 180" diagonal 16:9 Matte white, Dual-motor structure Projection Screen, Quiet Tubular Motor, Control system – Built-in IR / RF / RS232 / RS485 /12V Trigger / IP

ITC of 180" diagonal 16:9 Matte white, Dual-motor structure Projection Screen

Supply of 123''16:10 Matte white Shine B, Motorized Screen Quiet Tubular Motor, Built-in Smart Control, IR+RF, RF Emitter

ITC of 123''16:10 Matte white Shine B, Motorized Screen

Supply of Ceiling projector mount

ITC of Ceiling projector mount

Supply of 75” UHD Display Resolution: 3,840 × 2,160, Brightness:500 cd/m², Interface : HDMI(3)/DP/DVI-D/USB 2.0/ RS232C/ RJ45/ Audio/ IR, Response Time: 8ms,

ITC of 75” UHD Display

Supply of 65” UHD Display Resolution: 3,840 × 2,160, Brightness:330 cd/m², Interface : HDMI(3)/DP/DVI-D/USB 2.0/ RS232C/ RJ45/ Audio/ IR, Response Time: 8ms,

ITC of 65” UHD Display

Supply of Wall mount push pull bracket for 75" display

ITC of Wall mount push pull bracket for 75" display

Supply of Wall mount push pull bracket for 65" display

ITC of Wall mount push pull bracket for 65" display

Supply of In-room PC with Intel Core vPro i5-1145G7E, Windows 10 IoT Enterprise SAC, 8GB Soldered DDR4-3200, 256GB SSD M.2 2280 PCIe 3.0x4 NVMe, 2 x USB-A 3.2 Gen 2, USB-A 3.2 Gen 1, USB-C 3.2 Gen 2, USB-C 3.2 Gen 1 (for ThinkSmart Controller), 2 x HDMI out, Optional: HDMI in, RJ45 ethernet + 10.1" 10-point touch HD (1280 x 800), 16:10 aspect ratio, anti-glare & anti-smudge, 340 nits Controller Display

ITC of In-room PC

Supply of Wired Condenser 45.7cm / 18 inch Gooseneck with base, Cardiod Polar Pattern, Max 124.2 dB SPL, Freq Range 50 Hz-17 KHz, Dynamic Range of 96.2 dB 100 dB at 0 gain, Sensitivity of -35 dBC/Pa (17.8 Mv), 66 dB SNR ratio, -50 dB min Mute switch attenuation, Power: 11-52 Vdc phantom, 8 mA

ITC of Wired Condenser

Supply of Digital quad wireless receiver offers an intelligent four-channel option for use in any professional sound reinforcement application. Features include Digital Predictive Switching Diversity, 64 MHz tuning range, and AES 256 encryption for security, Working range: 100 m ( 330 ft), Output impedance: XLR connector 100 Ω, Gain adjustment range: −18 to +42 dB in 1 dB steps, Mic/Line switch: 30 dB pad, Power: 100 to 240 V AC, 50-60 Hz, 0.32 A max.

ITC of Digital quad wireless receiver

Supply of Handheld wireless transmitter compatible with a rugged yet lightweight aluminum body and integrated antenna, the Handheld delivers uncompromising audio quality and RF performance, AES 256-bit encryption for secure transmission, and advanced rechargeability options for professional sound reinforcement applications, Audio Freq Range: 50 Hz – 15 kHz (±1 dB), Input impedance 1 MΩ, Mic Offset Range os 0 to 21 dB, Wirless coverage of 100 meters, AES 256-bit Encryption, Rechargeable Li-Ion or LR6 AA batteries 1.5 V, Max input level: 1 kHz at 1% THD145 dB SPL (SM58), Occupied Bandwidth < 200 KHz

ITC of Handheld wireless transmitter

Supply of Wireless bodypack transmitter with a rugged yet lightweight aluminum case, the Bodypack Tx delivers uncompromising audio quality and RF performance, AES 256-bit encryption for secure transmission, and advanced rechargeability options for professional sound reinforcement applications, Audio Freq Range: 20 Hz – 20 kHz (±1 dB), Input impedance 1 MΩ, Mic Offset Range os 0 to 21 dB, Wirless coverage of 100 meters, AES 256-bit Encryption, Rechargeable Li-Ion or LR6 AA batteries 1.5 V, Max input level: Pad Off 8.5 dBV ( 7.5 Vpp) & Pad On 20.5 dBV ( 30 Vpp), Occupied Bandwidth < 200 KHz, Gain Adjustment Ranve: −25 to +15 dB

ITC of Wireless bodypack transmitter

Supply of Earset headworn omnidirectional microphone delivers exceptional speech clarity and enhanced plosive protection with no proximity effect. It features CommShield technology to stop RF interference, 3 color options, 3 windscreens and a protective pouch, Omnidirectional Polar Pattern, Freq response of 20 Hz to 20 KHz, Dynamic Range: 2500 Ω load 73 dB & 1000 Ω load 73 dB, Output impedance: 1800 Ω, Sensitivity: -41 dBV/Pa [1] (9 mV/Pa), SPL Level: 2500 Ω load 107 dB & 1000 Ω load 107 dB, SNR: 60 dB

ITC of Earset headworn

Supply of Dual docking recharging station charges can charge two battery/microphone at a time, 0.75 A maximum charge current, Charge time: 1 hour = 50% charged; 3 hours = 100% charged, Power requirement: 15 V DC, 3.33 A max

ITC of Dual docking recharging station

Supply of Rechargable battery for wireless microphone

ITC of Rechargable battery for wireless microphone

Supply of Wall/Ceiling Mount Antenna

ITC of Wall/Ceiling Mount Antenna

Supply of Antenna amplifier

ITC of Antenna amplifier

ITC Supply of Full range IP55 rated indoor/outdoor surface mounted music loudspeaker.

ITC of Integrated Zone Class-D Amplifier

ITC of AEC capable Digital Audio Conferencing Processor

Supply of 16–Port Master / Room Controller with PoE, 04 bidirectional RS-232 control ports, 04 IR emitter & 01 IR receiver ports, 04 GPIO control ports, 04 relays control ports.

ITC of 16–Port Master / Room Controller

Supply of Control for iPad

ITC of Control for iPad

Supply of Ipad with necessary mounting hardware

ITC of Ipad with necessary mounting hardware

Supply of PTZ Auto framing camera, ultra-low distortion loudspeakers, table top touch panel for control, 02 mic pods, with MTR bundle PC and necessary mounting kit

ITC of PTZ Auto framing camera

Supply of Table top mic pods

ITC of Table top mic pods

Supply of Multi format VC Collaboration Switcher: 4K60 18G 4x2, with HDMI, DisplayPort, & USB-C inputs, USB3.0/2.0 hub, simple display control, and 1 way PoC power, HDMI 2.0b, 4K/60Hz/4:4:4, HDCP2.2 Compliant

ITC of Multi format VC Collaboration Switcher

Supply of 4K60 4:4:4 / HDR 18G auto switcher with audio de-embed, ARC, IR, & RS232 control, Supports EDID management, HDCP 2.2 compliant

ITCof 4K60 4:4:4 / HDR 18G auto switcher

Supply of HDMI wall plate

ITC of HDMI wall plate

Supply of 24U rack with power strips and required rack accessories, caster wheels, shelfs, blank plates, screws, rails, vertical/ Horizontal cable managers etc.

ITC of 24U rack

Supply of Cable Cubby with 1 Universal Power Socket, 2 HDMI, 2 USB with sliding Lid.

ITC of Cable Cubby with 1 Universal Power Socket, 2 HDMI, 2 USB with sliding Lid.

Supply of 6' HDMI patchcord

ITC of 6' HDMI patchcord

Supply of 35' HDMI patchcord

ITC of 35' HDMI patchcord

Supply of 20' HDMI patchcord

ITC of 20' HDMI patchcord

Supply of Bulk cables and connectors, loudspeaker cable, CATX cable, audio cable, control cable and connectors (As required) - LOT

ITCof Bulk cables and connectors, loudspeaker cable, CATX cable, audio cable, control cable and connectors (As required) - LOT

NETWORKING SYSTEM Supply, Installation Testing of the following equipment for Networking System Horizontal CablingSupply of Dual Data faceplate with RJ45 Keystone, shutter, Flush-mount,

ITC of Dual Data faceplate with RJ45 Keystone, shutter, Flush-mount,

Supply of 24 Port Copper Patch Panel, Cat-6, Unloaded

ITC of 24 Port Copper Patch Panel, Cat-6, Unloaded

Supply of RJ 45 Keystone Jack, Unshielded, Cat-6

ITC of RJ 45 Keystone Jack, Unshielded, Cat-6

Supply of Network Cable, Cat-6A, UTP, 305m Roll

ITC of Network Cable, Cat-6A, UTP, 305m Roll

Supply of Cable Manager, 1RU, 19" Rack-Mount, Fingers/brush patch panel

ITC of Cable Manager, 1RU, 19" Rack-Mount, Fingers/brush patch panel

Supply of Copper Patch Cord, Cat-6, Unshielded, 1m

ITC of Copper Patch Cord, Cat-6, Unshielded, 1m

Supply of Copper Patch Cord, Cat-6, Unshielded, 2m

ITC of Copper Patch Cord, Cat-6, Unshielded, 2m

Supply of Copper Patch Cord, Cat-6, Unshielded, 3m

ITC of Copper Patch Cord, Cat-6, Unshielded, 3m

RACKS Supply of Rack, Floor Mount 42U, 800 Wide, 800 Deep, 2 Shelves, 1,PDU, 4 Fans

ITC of Rack, Floor Mount 42U, 800 Wide, 800 Deep, 2 Shelves, 1,PDU, 4 Fans

Supply of Rack, Wall Mount 15U, 600 Wide, 515 Deep, 1 Shelf, 1,PDU, 2 Fans,

ITC of Rack, Wall Mount 15U, 600 Wide, 515 Deep, 1 Shelf, 1,PDU, 2 Fans,

Supply of Horizontal PDU,6A Socket

ITC of Horizontal PDU,6A Socket

Passive Network Components Supply of 24port layer-2 managed switch, 24x 100/1000 copper ports, 4X 1G Fiber uplink ports

ITC of 24port layer-2 managed switch, 24x 100/1000 copper ports, 4X 1G Fiber uplink ports

Supply of 24 port layer-2 managed switch with POE, 24x 100/1000 copper ports, 4X 1G Fiber uplink ports

ITC of 24 port layer-2 managed switch with POE, 24x 100/1000 copper ports, 4X 1G Fiber uplink ports

Supply of Wireless Access points

ITC of Wireless Access points

Supply of Wireless Access Controller

ITC of Wireless Access Controller

Active Components Supply of 12 ports fibre Core Switch, 700W Dual Power

ITC of 12 ports fibre Core Switch, 700W Dual Power

Supply of 1G Fiber SFP transceiver

ITC of 1G Fiber SFP transceiver

Supply of Firewall

ITC of Firewall

Supply of Fiber Optic Indoor Cable, 6 Core, Multi-mode OM3

ITC of Fiber Optic Indoor Cable, 6 Core, Multi-mode OM3

Supply of 12 Port Fiber Optic Patch Panel/LIU with MM Duplex Adapters & Pigtails Splice Tray

ITC of 12 Port Fiber Optic Patch Panel/LIU with MM Duplex Adapters & Pigtails Splice Tray

Supply of OM3 1M LC-LC DUPLEX Patch cord

ITC of OM3 1M LC-LC DUPLEX Patch cord

Supply of OM3 3M LC-LC DUPLEX Patch cord

ITC of OM3 3M LC-LC DUPLEX Patch cord

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.32mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm

Supplying of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.

Laying of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

Installation of following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Installation of following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Installation of following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.450 mm width X 50 mm depth X 2.0 mm thickness

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray “bends “ ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray “bends “ ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required 300 mm width X 50 mm depth X 1.6 mm thickness

S pplying of following size of perforated Hot Dipped Galvanised Iron cable tray “bends “ ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required450 mm width X 50 mm depth X 2.0 mm thickness

Installaton of following size of perforated Hot Dipped Galvanised Iron cable tray “bends “ ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required 100 mm width X 50 mm depth X 1.6 mm thickness

Installaton of following size of perforated Hot Dipped Galvanised Iron cable tray “bends “ ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required 300 mm width X 50 mm depth X 1.6 mm thickness

In stallaton of following size of perforated Hot Dipped Galvanised Iron cable tray “bends “ ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required450 mm width X 50 mm depth X 2.0 mm thickness

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying of following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

Installation of following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Installation of following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Installation of following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

Supply of EPABX 20 Channel ISDN PRI with 08 Digital Extensions 100 Analog Extensions with CLIP 20 IP user licenses Features : • Inbuilt :Voice mail facilities with 24 Hours of Recording Time • ( Expandable by adding License ) • Inbuilt 3 Level DISA/DOSA/OGM • Remote IP and Smart Phone Extensions Compatibility • IP/ ISDN /TDM – Compatibilities • Built in-Networking Facilities (Q sig, ARS on VOIP • Multi Conferencing Facilities upto to 32 Party • 32 Bit Microprocessor or higher • Built In 10/100 Ethernet Port for VoIP communications and Computer Telephony Integration • Built in USB Port for management Applications • Built in Battery Interface port to connect external Batteries • The offered system should be equipped with redundant power supply unit (n+1) for the main control unit. The failure of the main power supply unit should not affect any operations of the IP-PBX. The system should be able to automatically switch over to the standby PSU without dropping any ongoing calls. • Built In LCR and ARS Facilities • Auth code and Walking Class of service facilities • SMDR/CDR for Call Tracking Facilities • Built in Hotel /Motel Applications • DECT Compatibility ( IP AND TDM) • 1000 Entries Speed Dialing • Pre Installed Communication Assistance • Paging Port – For External and Internal Paging Facilities * • Expandable up to -2000 Ports on One Look Network

ITC of EPABX

Supply of IP phone with the following minimum features • Tiltable graphical display, 3,7” (240*120 pixel), monochrome, LED backlight (white) • Notification LED (red/green/amber) • 4 context sensitive soft keys with LED(red/green/amber) • 2 fixed feature keys (Menu/Out-of-office) • 16 free programmable feature keys with LED (red/green/amber) • 4-way navigator, plus OK-key • 3 audio keys (Mute/Speaker/Headset)ith LED (red or green) • Volume control +/- • Open listening / Handsfree talking(Full-duplex) • Headset port (DHSG/EHS) • 10/100/1000 Base-T Ethernet Switch • Optional Circuit conversation integration • IEEE 802.3az Energy Efficient Ethernet

ITC of IP Phone

Supply of Analog Push Button Telephone with Display ,speaker Phone ,CLI

ITC of Analog Push Button Telephone with Display ,speaker Phone ,CLI

Supplying of 25 Pair MDF krone junction box with KRONE Module/Telephone cable termination.

Fixing of 25 Pair MDF krone junction box with KRONE Module/Telephone cable termination.

Supplying of 25 pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Laying of 25 pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying of single pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Laying of single pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.32mm

Supplying of following modular switch/ socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Fixing of following modular switch/ socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supply of Satellite Dish with LNB converter with required supporting structure at the roof and provisions to connect the RG 6 coaxial cable.

ITC of Satellite Dish with LNB converter with required supporting structure at the roof and provisions to connect the RG 6 coaxial cable.

Supply of Head End unit to receive signals from Satellite Dish and further distribute to the multiswich or the splitters.

ITC of Head End unit to receive signals from Satellite Dish and further distribute to the multiswich or the splitters.

Supply of Multiswitch to distribute satellite TV signals to multiple receivers.

ITC of Multiswitch to distribute satellite TV signals to multiple receivers.

Supply of Amplifiers to boost the signal strength.

ITC of Amplifiers to boost the signal strength.

Supply of 6 way Splitters with all necessary mounting accessories complete as required.

ITC of 6 way Splitters with all necessary mounting accessories complete as required.

Supply of 4 way Splitters with all necessary mounting accessories complete as required.

ITC of 4 way Splitters with all necessary mounting accessories complete as required.

Supply of 4 port tap off boxes with all necessary mounting accessories complete as required.

ITC of 4 port tap off boxes with all necessary mounting accessories complete as required.

Supply of Set up boxes with remote and with all necessary mounting accessories complete as required.

ITC of Set up boxes with remote and with all necessary mounting accessories complete as required.

Supply of 40" HD LED smart Android TV with HDMI(2)/DP/DVI-D/USB 2.0/ RS232C/ RJ45/ Audio/ IR with all necessary mounting accessories complete as required.

ITC of 40" HD LED smart Android TV

Supply of 40" Professional display Panel for Flight Information Display System with all necessary mounting accessories complete as required.

ITC of 40" Professional display panel for Flight Information Display System

Supply of Thin Client for Flight Information Display System with all necessary mounting accessories complete as required.

ITC of Thin Client for Flight Information Display System

Supply of RG 11U tinned copper co-axial cable with polythene insulation and overall PVC sheathed in 25/32mm dia FRLS PVC conduit from Head End unit to various Tap offs and Splitters.

Laying of RG 11U tinned copper co-axial cable

Supplying of co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Laying of co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm

Supplying of TV antenna socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

ITC of TV antenna socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Description of Work / Item(s)

Amount

60TR Scroll Chiller

AIR COOLED SCROLL CHILLER(2W+1S)

NOTE :Quoted price shall be inclusive of Supply, sea freight, insurance, packing and forwarding charges etc., as applicable Air Cooled Inverter based scroll Chiller Package of cooling capacity of 60TR at actual design conditions specified below Supply installation, testing, levelling & commissioning of Air-Cooled inverter chilled water Units complete with Multiple Scroll compressors, Evaporator, air-cooled condenser, Control panel etc. The chiller will be charged with R410A Refrigerant. The drive motor suitable for 415V +/-15%, 3 phase, 50 cycles/sec. All exposed power wiring shall be routed through liquid-tight, UV-stabilized, non-metallic conduit. Tandem refrigerant Circuit design with Multiple Compressors of up to #6 No's for enhanced inbuilt redundancy. Each refrigerant circuit shall include: a discharge service ball type isolation valve, dual high side pressure relief valves, liquid line shutoff valve with charging port, dual low side pressure relief valves, solenoid valve, sight glass with moisture indicator, electronic expansion valves, and flexible, closed-cell foam insulated suction line and suction pressure transducer, refrigerant receiver, discharge liquid separator and R410A refrigerant. The chiller evaporator shall be Brazed Plate Heat Exchanger(BPHE) type /shell and tube type. The heat exchange surface is configured so as to maximize the exchange coefficient with minimal load losses. capable of refrigerant working pressure of 650 psig and liquid side pressure of 150 psig. Input and output connections shall be fitted with air bleeder and draining valves. The covering in closed-cell neoprene sponge prevents the formation of condensation and reduces thermal wastage. Air-cooled Condenser with integrated fin and tube coils with inner grooved copper tubes and expanded into aluminium fins and complete with sub cooler and top discharge air circulators using EC(Electronically Commutated) axial flow fans with IP 55 protection for outdoor duty , U shaped condenser coil guard etc. permanently-lubricated ball bearings. Brushless commutation and minimum self-heating. Standard Hydrophilic Coating on the Condensor FOR BETTER PROTECTION Closed-cell, flexible, UV protected, thermal insulation for preformed flexible elastomeric cellular thermal insulation in sheet and tubular form. Thickness: Standard 38mm. Micro-processor based controls with alpha-numeric display in English for all operating parameters such as supply voltage, frequency, load current, chilled water inlet, chilled water outlet, condenser inlet and outlet temperature parameters, operating pressures etc.,

The compressor motor shall be with inverter driven and with protection for under voltage, over load, earth fault and single phasing, Integrated thermal protection, Speed control with inverter,Inverter start-up, Power factor correction, condensers, Oil valve and by-pass line, Anti-vibration supports etc. It should have Differential pressure switch, chilled water temperature sensors, water flow sensors / flow switch etc., Electronically commutated (EC) fans use more efficient motors and better aerodynamics to improve overall system efficiency and sound performance, particularly at partload. At reduced ambient temperatures, the head pressure control varies fan speeds to optimize the system efficiency and ensure reliable operation. This combination of variable speed compressor and fans provides a displacement power factor as high as 0.93, lowering electricity costs. (No. of fans should be Minimum 3 Nos) Compressor Motor overloads capable of monitoring compressor motor current. Provides extra protection against compressor reverse rotation, phase-loss and phase-imbalance. Motor overheat protection will be provided to ensure the motor reliability. Micro-processor based controls with Touch screen display in English for all operating parameters such as supply voltage, frequency, load current, chilled water inlet, chilled water outlet, temperature parameters, operating pressures, input power etc as per tender specification. The processor must be fitted with card for external communication for parameters in open protocol such as Bacnet. Hardware( viz IP router) and Software required for BMS interfacing should be part of chiller supply. Advanced Optiview Touch Screen Panel is available for enhanced control of operation at single point. Powder coating of all components. Victaulic coupling shall be part of the Chiller Package.Capable of delivering High Chilled water till 20C & same machine should capable of Operating as Heat Pump to deliver Hot Water at 55C in case of Operating it as Heat Pump during Winter . Chilled water Control of 0.1C Tolerance. The units shall be capable of providing cooling within ambient range of 10° C to 48°C Db. Noise level of the chiller should not be 65 db(A) at 1 m distance. All sound power or sound pressure level data at 100%, 75%, 50%, and 25% load, in accordance with EN03744. Spring type Vibration Isolators as per manufacturer standard supplied from the factory Actual cooling capacity at designed conditions indicated below : Ambient Temperature : 95F Refrigeration capacity : 60 TR(Actual capacity) Chilled water leaving temperature : 46 °F Chilled water entering temperature : 56 °F Fouling Factor (FPS) : 0.018 hr-sft- deg.F/Btu System minimum COP at 100 % load : Minimum 3.0 System minimum COP at IPLV : Minimum 5.2

Primary Variable Flow Pump(2W+1S) Supply, of horizontal split case end suction top discharge pump with baseplate centrifugal chilled water pump sets. Factory mounted on a common base with electric motor for recirculation of water for the central air conditioning system. bronze impeller with epoxy coating for inside surfaces, mechanical seal, three phase TEFC squirrel cage motor with IP55 protection. Vibration isolation springs, rubber isolation bellows flexible coupling for water circulation. All pumps shall be aligned properly as required and complete with mechanical seal. The pump motor shall be suitable for 415 + 10% volts, 50 cycles/second, 3-phase power supply. The quoted price shall include cost of thermal insulation, cladding and Spring vibration isolator. No impeller trimming is allowed. necessary flexible connection with required pressure rating. Pump to be supplied with inertia base.(PN16) Necessary drive arrangement & Noise levels to be 65 dBa from 1m of the unit Water flow rate = 144 USGPM Head = 75 feet. of water Minimum 75% combined motor & pump efficiency Motor efficiency- IE-3

Electrical Panel With PLC for Primary pumping system

Supply, installation of insulated closed type expansion tank with pressurization unit of adequate size complete with integral heavy duty butyl rubber diaphragm, suitable for PN 16 rating . Including 1 working & 1 stand by booster pumps complete with EPS/Nitrile rubber suitable thickness insulation covered with 30g aluminium cladding.Technical details as per specifications.Tank Capacity- 500 Litres Pump Capacity: 10 USGPM/25m Head

Supply & Installation testing & commissioning of a microbubble type air separator on the return water line located at the pump suction and suitable for the water flow, The separator should be complete with high capacity air vent, service valve, non return valve, butterfly valve connection for makeup water inlet, flanges etc. PN 16 rating. including pre breaker system, Fiberglass insulation of 75mm thickness & density 80 kg/cu.m shall be used and finally finished with 0.63mm Aluminium cladding.Dia-150 MM

20 TR/7600 CFM/30MM ESP

22 TR/8500 CFM/30MM SP

22TR/8800 CFM/30MM ESP

30 TR/12000 CFM/30 MM ESP

36 TR/14000 CFM/30 MM ESP

9TR/1700 CFM/25MM ESP

20 TR/2900 CFM/30MM ESP

FAN COIL UNITS (FCU) For Chilled water application. Supply of ceiling concealed type low static Fan Coil Units with 3 speed AC fan motor, having coil section, blower section, EU 1 filter section, with insulated extended drain tray made of staineless steel material, supports, chilled water connections, Flexible canvass connection etc. of the following capacities. Extended tray should accommodate all valves & 2-way PIBCV on/off valves, etc. as per the specifications and approved drawings. FCU shall be supplied with single phase starter with 24V volt stepdown transformer. Cooling Coil should be made of copper with hydrophilic coating. Number of rows of coil shall be 3 rows and fin should be made of aluminium. Type of Pipe connection (LHS/RHS) should be considered as per approved FCU GA drawing and shop drawing. The valve package comprising of pressure independent Balancing cum Control Valve with integrated 2 way motorized actuator in a single body for modulating operation suitable for static pressure of 1600 kPa and actuator shall be capable of withstanding 400 kPa shut off pressure, 24 V AC incoming power supply, ball valve with strainer for Inlet & ball valve without strainer for outlet connections. Thermal insulation of valves package with class 'O" tubular nitrile rubber materials shall also be considered under this scope. All these valves shall be supplied by the FCU supplier and factory assembled to the FCU. The Valve and actuator shall be suitable for the third party BMS operation & monitoring. The actuator of modulating valve shall be provided with interface cards to receive 0-10V or 4-20 mA signal from Digital Thermostat. Motor shall be of TEFC, IP-20 protection, Class B insulation, suitable for 1phase, 230volts, 50hz power supply, As per tender drawing and specification. Provision shall be made to connect fire module to switch off the unit during fire.

1 TR/400 CFM/5mm ESP

1.5 TR/ 560 CFM/5mm ESP

2 TR/800 CFM/5mm ESP

3 TR/1200 CFM/8mm ESP

3.5 TR/1350//8mm ESP

CHILLED WATER TYPE HI WALL UNITS Wall mounted Hi-wall type unit suitable for chilled water application. The unit shall have necessary filters, cooling coil, fan, fan motor, decorative panels, cordless digital remote control unit etc., The unit scope of supply shall include Inlet & Outlet ball valve, 'Y'-Strainer, 2way on/off valve with actuator, all necessary control wiring, power cabling of 2m length with plug-top, supports, isolators, insulation of valves etc.,

1.0 TR - 400cfm

Supply & installation of 500mm flexible insulated braided pipe with flair connection for FCU supply & return connection.

Supplying, installing, testing and commissioning of inline duct mounted modular type dry scrubber with primary filter with activated carbon filter . The unit shall be suitable for 220 + 10% volt single phase power supply. The unit shall be suitable for floor mounted or ceiling suspended or floor mounted type.Vendor to include neccesary supporting system with vibration isolators. 10500 CFM/75mm ESP

Supplying, installing, testing and commissioning of SISW fans for kitchen exhaust. The unit shall be powder Coated, acoustically Insulated, double Skin Cabinet suitable for outdoor applications suitable for installing in any position in horizontal ducts. The fan shall be SISW backward curve aerofoil fitted with maintenance free external motor mounted outside airstream with fire rating of 250 deg C for 2 Hrs. The motor shall be suitable for 415+10% volts, 50 Hz, 3 phase power supply. Total static shall be 75mm WG.Fan to be provided with Canopy. 10500 CFM/75mm ESP

Suppy, installation, testing and commissioning of Smoke extraction Axial fan shall comprise fan section with adjustable blade angles to deliver the design air quantity. The axial fan assembly shall be housed in a casing made of Mild Steel with enamel Painted, adjustable pitch die cast aluminium impeller (Hub and blades). The Motor shall be air over cooling type with IP-55 protection, Class 'H' insulation, IE-2 efficiency, suitable for 3phase, 415volts, 50hz power supply. Fan position shall be as per the tender drawings. Axial fan with AMCA certification (For AIR, SOUND Performance).Fan shall be fire rated for 250 Deg C for 2 Hrs. The units shall be with inlet protection guard, fire rated Canvass connection(Round to rectangular transition type with flanges), Backdraft damper and adjustable spring isolator, supporting rods as per specifications. Vendor to consider the cost painting the unit with black colour.

6000 CFM/20mm ESP

3000 CFM/20mm ESP

Supply,installation,testing & commissioning of Propeller fan complete with 1 Phase motor,impeller & gravity louver and motor shall be suitable for 1 phase, 230V,50Hz.. (100 dia)

Supply, installation, testing & commissioning of Exhaust fan, floor mounted, suitable for Outdoor installation as per specification . Double Skin wall panels, 25 mm thick sandwich PUF injected panels. Outer skin shall be 0.63mm pre plasticized or powder coated GSS sheet. Inner sheet shall be 0.63mm plain GSS. Extruded Aluminium corners. Complete with Glass view panel, motor guard, limit switch, cable entry, GSS base frame, Intake cutout with zero leakage in the panel joints. Inspection door for all the sections.Each complete with DIDW Backward curved Centrifugal Fan , MS Frame work for fan, vibration isolators, The Fan scroll shall have inspection / access hatch for blade inspection & cleaning purpose. Suitable drain plug shall be provided at the bottom of Fan for easy drain out. Fan Bearing shall be outside the fan for easy maintenance. fan Motor shall be suitable for 415±10% volts, 50 cycles/second, 3 phase AC supply. (Suitable for outdoor installation) Noise Level to be 70dB from 1.5m from source. . The cost shall include fire rated canvas , Al Volume control damper .Fan shall be provided with canopy.

Supply, installation, testing & commissioning of Rectangular type inline fan with acoustic insulation and pre filter. Fan shall be complete with motor,neccesary hanging accessories etc.Fan casing shall be of 1mm GI sheet & motor shall be suitable for 230V,50 Hz, 1 Phase. 1000 CFM/15mm ESP

Supply , Laying, fixing, testing and commissioning of Site insulated MS Class C chilled water pipes. Pipe shall be supported with MS supports. Vendor to consider necessary cost of fittings like bends, tees, reducer etc. PUF insulation shall have density of 36 Kg.cum , 90% closed cell content, minimum compressive strength of 2.7 Kg/Cm^2 and initial thermal conductivity of 0.02 W/mK. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. In case of difficulty for structural support, Wire rope Supports Gripple (double channel wedge lock, unlocking device should not be integral part of grip for added safety) complete with end fixing shall be used. Wire Hangers shall be independently tested by reputed third party testing organization to sustain safe working load for 120min at elevated temperature of 175 deg. C or above. System shall be in accordance with the approved shop drawings and as required by the specifications

150mm dia.(50 mm thick insulation )

125mm dia.-(50 mm thick insulation )

100mm dia.(50 mm thick insulation )

80mm dia. (50 mm thick insulation)

65mm dia.(30mm thick insulation )

50mm dia.(30 mm thick insulation )

40mm dia.(30 mm thick insulation )

32mm dia.(30 mm thick insulation )

25mm dia.(30 mm thick insulation )

Supply ,Laying,fixing,testing and commissioning of Pre insulated MS Class C chilled water pipes for plant room. Pipe shall be supported with MS supports.Vendor to consider necessary cost of fittings like bends, tees,reducer etc. PUF insulation shall have density of 36 Kg.cum ,90% closed cell content,minimum compressive strength of 2.7 Kg/Cm^2 and initial thermal conductivity of 0.02 W/mK. Insulation shall be cladded HDPE Jacketing og thickness as specified in the BOQ line item. . Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.Pipe shall be supported with MS angle with High Density PUF saddles.

150mm dia.(50 mm thick insulation with 6.9mm HDPE jacketing)

100mm dia.(50 mm thick insulation with 5.5mm HDPE Jacketing)

80mm dia.(50 mm thick insulation with 4.9mm HDPE Jacketing)

Supply,installation,testing and commisioning of Pressure Independent dynamic balancing cum equal percentage type modulating flow control valve fitted with high torque actuator with non spring return to ensure the valve remains in the position in the event of power disconnect to actuator. Actuator enclosure shall be rated for IP 54 protection. Step down transformer if required shall be part of valve supply, matching flanges, hot dipped galvanized bolts and nuts. Valve body to be insulated with closed cell elastomeric insulation.Actuator should be provided with position feed back switch and also actuator should have BMS interfacing card and shall be suitable for accepting signals from temperature sensors supplied by BMS vendor. Actuator should also have facility to set the required flow rate as per site requirements through dip switch adjustments. Valve body to be rated for PN 16. The valve design flow rate should be factory calibrated with +/- 5% flow accuracy.

52.8 GPM/65 mm Dia

55.2 GPM/65 mm Dia

86.4 GPM/80mm Dia

48 GPM/65 mm Dia

72 GPM/65 mm Dia

21.6 GPM/40mm Dia

Supply, installation, testing and commissioning of motorised modulating type Globe valve, Shall operate based on DP sensor/BTU meter feedback with Pressure rating of PN 16 & insulation as per specifications, Complete actuator interchangeability, allowing easy field retrofit or mounting using standardized mounting kits, Should fallow ANSI class 250(PSIG) standard & Factory tested 100 mm Dia

Supply, installation, testing and commissioning of Motorized On/Off type butterfly valve with internally moulded rubber lined body,EPDM seal material, central ductile iron disc & overall conformity to std API 609 category IS 13095 Butterfly valve with Pressure rating of PN 16. The actuator shall be of Motorised ON/OFF type with suitable transformer as per specifications(NOTE: Valve to be provided with addditional shoe piece on either side of valve for easy connection to pipe) 100mm

Supply, installation of 20mm Auto air vent with ball valve made of gun metal.

SITC of nitrile rubber insulated Ball valve made from forced brass boddy and steel handle. 25mm Dia

Supply & installation of test point made of forced brass metal.

SITC of Flow meters inclusive of matched pair temperature sensor with the necessary accessories for installing the sensors. Shall be suitable for 230V AC power supply, Protection category of IP65, Modbus RTU, flanges for connection, ultrasonic flow measuring components mounted perpendicular to the flow. The flow meter shall be thermally insulated with elastomeric nitrile rubber and finished with Treated Woven Glass Cloth with two layers of epoxy paint-150mm Dia

SITC of BTU meter shall include the following Heat Meter Integators & Flow meters. Heat Meter Integators: Shall include calibrated pair temperature sensor with the necessary accessories for installing the sensors.Shall have the features of Battery Backup up to 10 Years, Data logging for up to 15 years, 230V AC power supply provision, 8 Digit LCD display, Protection category of IP54, Modbus RTU. Flow meters: The flow meter shall include screwed / Flanged meters incorporate ultrosonic flow meters type that are mounted perpendicular to the flow. The meters shall use a magnetic transmission system between the impeller and the totalising register.

25mm Dia

32mm Dia

40mm Dia

65mm Dia

80mm Dia

SITC of Differntial pressure transducer with sensing probes, ball valves and associated accessoreis

SITC of Insulated BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot water circulation as specified. Valve to be duly insulated with material same as pipe insulation.

150 mm dia

125 mm dia

100 mm dia

80 mm dia

65mm dia

50 mm dia

40 mm dia

SITC of Insulated BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified.Valve to be duly insulated with material same as pipe insulation. 100 mm Dia

SITC of Insulated NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified.Valve to be duly insulated with material same as pipe insulation. 100 mm Dia

SITC of Insulated Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.Valve to be duly insulated with material same as pipe insulation.

100 mm dia

80 mm dia

65mm dia

40 mm dia

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Brick work in C.M 1:5 mix using 2nd class ground moulded chamber burnt bricks with including cost

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required

thickness 0.63 mm sheet

thickness 0.8 mm sheet

thickness 1.0 mm sheet

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required

thickness 0.63 mm sheet

thickness 0.8 mm sheet

thickness 1.0 mm sheet

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications. Dia-200mm

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.

Fire damper

Actuator

Double skin powder coated plenum should be of factory fabricated, constructed with outer skin with not less than 0.63mm thick GI sheet and the inner sheet shall be of not less than 0.63mm GI plain sheet., with 25mm thick sandwiched RPUF ( CFC free) insulation of density not less than 40kg/m³. And with necessary High grade Extruded Aluminum cross supports for rigidity and cutouts for duct & AHU connections. THE PLENUM SHALL BE PROVIDED WITH AN ACCESS DOOR of size not less than 800mm x 600mm.

SITC of Spigots with butterfly damper should constructed with not less than 0.8mm thick galvanized steel sheet, with single flap, necessary stopper, flanges for fastening on to the duct surface and with grooves for clamping the flexible ducts securely.

100 mm Dia.

150 mm Dia.

SITC of round flexible duct inner core should be made of double lamination of Aluminum Foil, Polyester & Metalized polyester film permanently bonded to a coated spring steel wire helix. Fiberglass insulation shall be of 25mm thick with minimum density of 16 kg/m³. The outer insulation jacket vapor barrier shall be made of fiber glass reinforced metalized polyester film laminated with aluminum foil as per the technical specifications.

100 mm Dia.

150mm Dia.

SITC of collar damper shall be constructed out of extruded aluminum alloy with multiple blade of oppose blade type. Shall be used for the supply air diffuser & grilles as per the drawings & specifications.

SITC of supply air round type Diffuser shall be of removable core type and constructed with high grade aluminum extruded alloy and with powder coated finish with flanges and plenum bixwith double flap damper. Double flap damper for round diffusers are used wherever gypsum ceiling is provided. Where the diffusers are accessible spill air box with butterfly damper shall be considered.butterfly dampers are quantified separately

Neck size: 150 dia Outer size:225 Standard

Neck size: 200 dia Outer size:325 Standard

SITC of return air Diffuser shall be of removable core type and constructed with high grade aluminum extruded alloy and with powder coated finish with flanges and plenum box without double flap damper

Neck size: 150 dia Outer size:225 Standard

Neck size: 200 dia Outer size:325 Standard

SITC of Exhaust valves constructed from steel spinning with powder coated finish. The valve should provided high initial resistance with wide throttling capability to offset the high system resistances. And finished with powder coating. Neck size: 100mm dia.

Supply and Installation of pressure independed type VARIABLE AIR VOLUME BOXES consisting of Damper Actuator control , transformer, velocity transducers, flow velocity sensors, T24 - MP or equivalent direct out put room temperature sensor, air tube etc. with all internal attenuation treatment and acoustical casing necessary to achieve the required noise criteria. ceiling suspended hanger brackets with vibration isolators clamping devices nuts and bolts etc. As per the field requirements.VAV shall be supplied with thermostat.

Range-53-550 cfm

Range-105-1000 cfm

Range-240-2300 cfm

Range-335-3100 cfm

Range-550-4800 cfm

Range-845-6500 cfm

SITC of microporcessor based , DDC controller / integrator with necessary interface for the communication with the BMS over Bacnet over MSTP/Modbus.

Supply and laying communication cabling between sensor and VAV/CAV Boxes 2C x1.5 Sqmm screened cable for VAV looping to the integrator in 19mm dia PVC conduit.

SITC of High grade aluminum extruded Louvers for Fresh air intake & Exhaust air exit at outer wall. The louver shall be of powder coated finish. The louver shall be with 45 deg deflection and shall prevent rain water entry through the louvers.

SITC of High grade aluminum extruded Louvers for Fresh air intake with 20-micron washable filter suitable for external application. Louvers shall be powder coated finish.

The supply & installation of FACTORY FABRICATED spill air boxes made out of 0.8mm thick GI sheet with necessary spigot connection for fixing flexible duct and suitable collar for connecting to various neck diffuser / slot diffuser. The box should be internally insulated with 10mm thick open cell nitrile rubber of class '1' material. The box size shall be as mentioned below.The cost shall be inclusive of necessary chain support

Supply & Installation, Testing and Balancing of Motorized modulating Volume control dampers(Aerofoil type),the opposed blade volume control, suitable for elliptical duct installations device shall be made of Powder aluminum construction in black anodized finish. Opposed blades shall be pivoted to Coated extruded aluminum frame with Nylon bushes. . Specially designed blade shall have an overlapping lip which shall ensure a tight closure .The cost shall include actuators and control panel and the cabling works

Supply & installtion of actuators with control panel.

Supply, installation, testing and commissioning of Door transfer supply air louver for toilets with Extruded Aluminium Powder coated . Fixing either with screw system or without screws by sealant of aluminium non vision typ eas per specifications as follows:

SITC of 24G GI cross talk duct with neccesary acoustic insulation. Vendor shall consider neccesary supporting system.

Supplying and fixing of following thicknessregular closed cell class 0 nitrile rubber insulation finished with factory laminated aluminium foil ,anti-microbial protection with 40 to 60 kg/m3 density. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.Insulation shall be supplied with adhesives. 19mm Thick

Supplying & fixing of Class "1" type, Open cell elastomeric Acoustic insulation with density not less than 140 kg / m3. Insulation material to be fire retardant. Moisture resistant-joining tapes of 2 inches width with self adhesive to be supplied with the insulation material by the supplier.

10mm thick

25mm thick-for AHU room with GI wire mesh

2.2KW-DOL

3KW-DOL

Supply ,laying and commissioning of flexible sheated type copper cable of following size with ternimation lugs and glands.

3cx 1.5 Sqmm

3cx 2.5 Sqmm

3cx 4Sqmm

Supply ,laying and commissioning of XLPE insulated armoured type alumiumr cable of following size with ternimation lugs and glands. 3Cx 16mm

Supply ,laying and commissioning of XLPE INSULATED armoured Aluminium cable of following size with end terminations.

4Cx 4Sqmm

4Cx 6Sqmm

4Cx 10Sqmm

SITC of GI earthing Strips of 8SWG wire

SITC of O3 Ozonator complete with transformer,high frequency electrode and Low voltage electrode and insulating material.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

Isolating and Cutting the Exiting Chilled Water line-80mm Dia

Description of Work / Item(s)

Amount

2850 lpm at 88 m Head

2850 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of the following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.As per standards, specification and directed by the Engineer-in-charge.

180 lpm at 88 m Head

Providing, laying, testing & commissioning of 'C' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :As per standards, specification and directed by the Engineer-in-charge.

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

150mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous unmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :As per standards, specification and directed by the Engineer-in-charge. Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :As per standards, specification and directed by the Engineer-in-charge.

50mm nominal dia

80mm nominal dia

100mm nominal dia

150mm nominal dia

200mm nominal dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.As per standards, specification and directed by the Engineer-in-charge.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :As per standards, specification and directed by the Engineer-in-charge.

80mm nominal dia

150 mm nominal dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.As per standards, specification and directed by the Engineer-in-charge.

80mm nominal dia

100mm nominal dia

150mm nominal dia

200mm nominal dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required As per standards, specification and As per standards, specification and directed by the Engineer-in-charge. (Gun Metal)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.As per standards, specification and directed by the Engineer-in-charge. 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :As per standards, specification and directed by the Engineer-in-charge. (Gun Metal)

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. As per standards, specification and directed by the Engineer-in-charge.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :As per standards, specification and directed by the Engineer-in-charge.

Pendent Sprinkler

Upright Sprinkler

Horizontal Side throw Sprinkler

concealed sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. 15 mm dia 15mm dia As per standards, specification and directed by the Engineer-in-charge.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. As per standards, specification and directed by the Engineer-in-charge. 100mm nominal dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.As per standards, specification and directed by the Engineer-in-charge.

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required As per standards, specification and directed by the Engineer-in-charge.

Supplying,installing,of FIRE DOOR having 2hr rating and smoke control long with frame, to fabricated out of G.I.sheet to house the above accessories locks, latches and other essential ironmongery fitted with intumescent and smoke seal. Doors shall be tested to BS 476 Part 22. (fire duct door 900x1200mm)As per standards, specification and directed by the Engineer-in-charge.

Supplying,installing,testing and commissioning approved make cast iron body brass NRV with Pressure rating of PN 16. with necessary flanges ,nuts and bolts etc,complete on the delivery header

Supplying,installing,testing and commissioning of automatic air release valve as detailed in the drawing and to be installed at the top most points of hydrant risers 25 mm

Supplying and fixing of perforated G.I.sheet cable tray with neccessory angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall not exceed 500 mm.Size of the tray shall be 300 x 50mm and 2mm thick.

G.I Earthing strips of 25mm x 6mm thick, strip shall b e run on floor / ceiling / walls from the equipment to the nearest earth pit with necessory accessories as required. ( Earth pit shall be executed by other agencies)

Supply, erection, of MS structural supports for above 100 dia pipes and parking sprinkler supports joints / welded joints. shall be two coats of approved synthetic enamel paint over one coat of zinc chromate primer. Rate quoted shall including all the accessories

Supply, installation, testing and Commissioning of 150 mm dia dial type pressure gauge in the sprinkler pipe lines with glycerin filled brass ball valve of suitable dia and SS tubing & socket having range (0-32 bar) as required., and complete as per specification.

1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing & commissioning of FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc.The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The rate shall excludes tray & Hume pipes. The minimum size of the cables shall as mentioned below, As per standards, specification and directed by the Engineer-in-charge.

3C x 185 sq.mm aluminum for main pumps

3C x 95 Sqmm. Aluminum Water nozzle pumps

3C x 25 Sqmm. Aluminum Jockey pumps

12 C x 2.5 Sqmm. Copper armoured for Diesel engines

2 C x 2.5 Sqmm copper armoured for Instrumentation

End Terminations

3C x 185 sq.mm

3C x 95 Sqmm.

3C x 25 Sqmm.

12 C x 2.5 Sqmm.

2 C x 2.5 Sqmm

Supply,Installing, testing and commisioning of ABC powder type Fire Extinguisher of 6 Kg. capacity refillable type fitted with internal discharge tube, pressure guage, squeez grip, nozzle and suspension bracket and fixing screws complete with initial charging. All to be confirmed to latest BIS codes As per standards, specification and directed by the Engineer-in-charge.

Supply,Installing, testing and commisioning in position approved make Dry Chemical Powder Fire Extinguisher of 6 Kgs capacity complete with chromium plated gun metal union (cap), fitted with braided hose and open nozzle with initial charge of Dry Chemical Powder and gas cartridge complete with suspension bracket and fixing screws. The extinguisher is internally and externally coated with lead tin alloy through hot dip process and cylinder bearing No.IS:2171/1976 and the gas cartridge bearing with ISI certification mark. As per standards, specification and directed by the Engineer-in-charge.

Supply, installation, testing and commissioning of approved make Fire Bucket of 24 Gauge, galvanised steel sheet, standard 9 ltrs, capacity and of round bottom shape, painted white inside and red outside and black on the bottom dome with letters "FIRE" in black and gold with wall mounting bracket and screws. All to be confirmed to latest BIS codesAs per standards, specification and directed by the Engineer-in-charge.

Fire bucket stand fabricated by MS angles to install 2 Nos. of buckets.

Supplying, installing and commissioning of Carbon-di- oxide type fire extinguisher of 4.5 kgs Capacity refillable type fitted with internal discharge tube, pressure guage, squeez grip, bend and horn, nozzle with suspension bracket and fixing screws complete with initial charging CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve. All to be confirmed to latest BIS codes.As per standards, specification and directed by the Engineer-in-charge.

Supply,Installing, testing and commisioning in position approved make Water mist type extinguisher of capacity 9L capacity refillable type fitted with internal discharge tube, pressure guage, squeez grip, nozzle and suspension bracket and fixing screws complete with chromium plated gun metal union (cap), fitted with braided hose and open nozzle with initial by applying low pressure, fine water droplets, known as ‘WaterMist’ over, around and into the flame, suffocates the fire. The extinguisher is internally and externally coated with lead tin alloy through hot dip process and cylinder requirements. Complies with BS 5306 maintenance As per standards, specification and directed by the Engineer-in-charge.

Supply,Installing, testing and commisioning in position approved make Water mist type extinguisher of capacity 4L capacity refillable type fitted with internal discharge tube, pressure guage, squeez grip, nozzle and suspension bracket and fixing screws complete with chromium plated gun metal union (cap), fitted with braided hose and open nozzle with initial by applying low pressure, fine water droplets, known as ‘WaterMist’ over, around and into the flame, suffocates the fire. The extinguisher is internally and externally coated with lead tin alloy through hot dip process and cylinder requirements. Complies with BS 5306 maintenance As per standards, specification and directed by the Engineer-in-charge.

Providing and installing in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC non-reflective self adhesive vinyle painted foam board, complete with mirror fasteners.

Providing and installing in Signage with printed "IN CASE OF FIRE, USE FIRE EXIT WAYS UNLESS INSTRUCTED OTHERWISE" of 1.25cm height letters in red with white back ground.The size of the board shall be 25cm x 30 cm and shall be fixed at the height of 2 mts from finished floor near Manual call points.

Providing and installing in Floor indentification signage ( ie, GROUND FLOOR …etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with . Led emergency light Material: Aluminium box+PMMA board Size: 360*200mm Features: Overcharge protection Light source: 3W led lights Light color: White led Voltage: AC90-260V 50/60Hz, AC110V~60Hz, AC220V~50Hz Battery:Ni-Cd1.2V Duration time: 90Mins or 3Hours Charging time: 24hour Automatically Power switch Finish: Double-side side printing

Providing and installing in Fire exit sign with arrow indicating the way to escape route shall be provided at suitable height from floor level on the ceiling & shall be illuminated by electric light .The lettering size shall be 7.5 cm with contrasting colour from back ground.Size shall be 15cm x 30cm. Light source: 3W led lights Light color: White led Voltage: AC90-260V 50/60Hz, AC110V~60Hz, AC220V~50Hz Battery:Ni-Cd1.2V Duration time: 90Mins or 3Hours Charging time: 24hour Automatically Power switch Finish: Double-side side printing

Providing and fixing in position the signages " FIRE ORDER" it should contain the following matter on 3mm thick "Opaque" PVC foam board of computerised cut, PVC non-reflective self adhesive vinyle painted foam board of 2' x 3'.i. Alert the security at security room by actuating manual call point located at strategic locations. ii. Evacuate the occupants by using fire exits and emergency exits only and assemble at various assembly poits. iii. If possible try to extinguish the fire by using nearest / suitable portable extinguisher or water from nearest wet riser.iv. Be calm and do not give any room from panic, walk, do not run. v. If you encounter serious difficulty in evacuation, flat and try to attract attention of rescue team.Action by security/reception upon receipt of information through fire alarm orfire detectors or by using public address system. i. Alert the occupants by using public address system.ii. Inform fire control through any one of the following phone numbers: iii. Refer evacuation plan from evacuating standard people. iv. Guide the fire force, on their arrival to the seat of fire. v. In case of the casualties, call ambulance by dialling number

Signage with printed ''Assemble Point " of 1.25cm height letters in green with white back ground. For gathering outside the building during fire emergency.

Supplying and installing of in position the signages " FIRE HYDRANT & HOSE REEL" with symbol it should contain the following matter on "Opaque " PVC foam board of computrized cut, PVC Non-reflective self adhesive vinyle painted foam board

Supplying and installing of in position the signages " MCP " with symbol it should contain the following matter on "Opaque " PVC foam board of computrized cut, PVC Non-reflective self adhesive vinyle painted foam board

Supplying and installing of in position the signages " Fire Extinguisher " with symbol it should contain the following matter on "Opaque " PVC foam board of computrized cut, PVC Non-reflective self adhesive vinyle painted foam board

Supplying,installing,testing and commissioning of Foot Valve with Lever used at inlet of negative suction pump. it should act as a modified check valve that has a screen or strainer on the suction end to prevent debris entering the pump or pipe. Pressure range max 20 kgf/ cm2 with necessary flanges ,nuts and bolts etc,complete and Foot valves shall be designed as per IS-10805 and flange type construction. complete as per specification

100mm dia

150mm dia

200mm dia

FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required. As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of fault isolator complete with base as required As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of addressable fire control module complete as required As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required.As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of addressable manual call point complete as required. As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required As per standards, specification and directed by the Engineer-in-charge.

PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.As per standards, specification and directed by the Engineer-in-charge.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS As per standards, specification and directed by the Engineer-in-charge. outer sheath complete as required. (RED COLOUR)

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS As per standards, specification and directed by the Engineer-in-charge. outer sheath complete as required.(BLUE OR BLACK FOR PA SYSTEM)

4 Loop Panel

Supplying, installation, testing & commissioning of intelligent analog addressable multi-sensor detector with sounder base complete with all mounting accessories complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable control relay module complete with all mounting accessories complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable monitor module complete with all mounting accessories complete as required.

Power Supply unit for hooters as required.

25mm FRLS heavy duty PVC conduits on ceiling / wall complete with accessories like, Junction boxes, Collars, Bends etc.

GI 3 Module metal box for installing Control module,Fault Isolator Module,Monitor Module, Relay Module ,Sounders, Etc

GI 2 Module metal box for installing MCPs

200 MM and 2 mm thick perforated GI cable tray with cover complete with angle, iron heavy supports/hanging arrangement,Bends,tees etc.with all accessiories.

Description of Work / Item(s)

Amount

Part A LT panel Baord

LT PANEL BOARDS WORKS Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of Main LT Panel (Indoor Type) Incomer -1: 1 No. 630 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 Ea Digital type Multi Data meter (EM 6400) with RS485 Port with 630/5A 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Incomer-2 : 1 No. 630 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 630/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Bus Coupler : 1 No. 630 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel : “ON, OFF & Trip" indicating lamp. The all Incomers & Bus Coupler shall be provided with Suitable mechanical Interlocking arrangements with 3 Lock + 2 Keys, Emergency Push Button. Outgoings : 250A 4P 36KA TMD Based O/C, S/C & Aux MCCB with RHOM, Phase Barrier & Spreaders, Digital type Multi Data meter (EM 6436) with RS485 Port, 250/5A, 5VA burden Cl:0.5 resin cast CT's, ON/OFF & Trip indicating lamp - 12 EA, With necessary Al. bus bars, interconnections, All MCCB's should have two (spare) potential free contactor for BMS monitoring. 630A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of AC Panel (Indoor Type) Incomer -1: 1 No. 630 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 630/5A, 10VA burden Cl:0.5 resin cast CT's, , Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Outgoings : 250A 4P SFU Digital type Multi Data meter (EM 6436) with RS485 Port, 250/5A, 5VA burden Cl:0.5 resin cast CT's, ON, OFF indicating lamp - 6 EA, With necessary Al. bus bars, interconnections, All MCCB's should have two (spare) potential free contactor for BMS monitoring. 630A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of Restaurant Panel (Indoor Type) Incomer 1 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Incomer-2 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Bus Coupler : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel : “ON, OFF & Trip" indicating lamp. The all Incomers & Bus Coupler shall be provided with Suitable mechanical Interlocking arrangements with 3 Lock + 2 Keys, Emergency Push Button. Outgoings : 125A 4P SFU with ON, OFF indicating lamp - 4 EA, 63A 4P SFU with ON, OFF indicating lamp - 8 EA, With necessary Al. bus bars, interconnections, All MCCB's should have two (spare) potential free contactor for BMS monitoring. 250A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work

Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of Chiller Panel (Indoor Type) Incomer 1 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C, S/T & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Incomer-2 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C, & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Bus Coupler : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel : “ON, OFF & Trip" indicating lamp. The all Incomers & Bus Coupler shall be provided with Suitable mechanical Interlocking arrangements with 3 Lock + 2 Keys, Emergency Push Button. Outgoings : 1605A 4P SFU with ON, OFF indicating lamp - 6 EA, With necessary Al. bus bars, interconnections, All MPCB & MCCB's should have two (spare) potential free contactor for BMS monitoring. 250A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work

Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of Common Area Panel (Indoor Type) Incomer 1: 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Incomer-2 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Bus Coupler : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel : “ON, OFF & Trip" indicating lamp. The all Incomers & Bus Coupler shall be provided with Suitable mechanical Interlocking arrangements with 3 Lock + 2 Keys, Emergency Push Button. Outgoings : 125A 4P SFU with ON, OFF indicating lamp - 2 EA, 63A 4P SFU with ON, OFF indicating lamp - 12 EA, With necessary Al. bus bars, interconnections, All MCCB's should have two (spare) potential free contactor for BMS monitoring. 250A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work

Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of Transit Block Panel (Indoor Type) Incomer 1 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Incomer-2 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Bus Coupler : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel : “ON, OFF & Trip" indicating lamp. The all Incomers & Bus Coupler shall be provided with Suitable mechanical Interlocking arrangements with 3 Lock + 2 Keys, Emergency Push Button. Outgoings : 63A 4P SFU with ON, OFF indicating lamp - 8 EA, 25A DP 10KA O/C, S/C MCB - 49 EA, With necessary Al. bus bars, interconnections, All MCCB's should have two (spare) potential free contactor for BMS monitoring. 250A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work

Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of Admin Office Panel (Indoor Type) Incomer 1 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Incomer-2 : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 250/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF & Trip" indicating lamp. Bus Coupler : 1 No. 250 Amps 4 pole 36 KA TMD based MCCB with O/C, S/C & Aux. Instruments Panel : “ON, OFF & Trip" indicating lamp. The all Incomers & Bus Coupler shall be provided with Suitable mechanical Interlocking arrangements with 3 Lock + 2 Keys, Emergency Push Button. Outgoings : 63A 4P SFU with ON, OFF indicating lamp - 14 EA, With necessary Al. bus bars, interconnections, All MCCB's should have two (spare) potential free contactor for BMS monitoring. 250A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work

Supply, Loading, Unloading, Storing, Shifting to Installation Loacation, Installation, Testing & Commissioning of AHU Panel (Indoor Type) Incomer 1 : 1 No. 125 Amps 4 pole SFU. Instruments Panel :1 EA. of Digital type Multi Data meter (EM 6400) with RS485 Port with 125/5A, 10VA burden Cl:0.5 resin cast CT's, Ammeter with ASS, Voltmeter with VSS, control MCB's, RYB Indication lamps and “ON, OFF" indicating lamp. Outgoings : 63A 4P SFU with ON, OFF indicating lamp - 9 EA, With necessary Al. bus bars, interconnections, All MCCB's should have two (spare) potential free contactor for BMS monitoring. 125A Amps TPN Aluminium bus bars : All the neutral bus bars shall have the half capacity of phase bus bars (0.8A/Sq. mm.), Complete All as per BOQ & Single Line Diagram, with all lead and Lifts and as directed by the Engineer-In-Charge of the work

Supply, Fixing, Testing & Commissioning of UPS COS Enclosure FOR 25KVA UPS Bypass: 63A 4P On Load Manual Chage Over Switch with source-1 & 2 indication Lamps & RYB Indication lamp with Control MB and necessary interconnections. Complete All as per BOQ with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Fixing, Testing & Commissioning of UPS I/P & O/P BREAKER MCB Enclosure FOR 25KVA & 10KVA UPS: 63A 4P 10KA 'D' curve MCB With O/C, S/C and necessary interconnections. Complete All as per BOQ with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Part-B - LT Cable & Terminations

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3.5 core 400 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3.5 core 240 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3.5 core 185 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3.5 core 150 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3.5 core 120 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3.5 core 70 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3.5 core 25 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 4 core 25 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 4 core 16 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 3 core 10 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 4 core 6 sqm

Supply, Testing and Commissioning of 1.1 kV grade 1C/3C/3.5C & 4C stranded XLPE(above 6 sq.mm)/Class A PVC insulated(below 6 sq.mm), FRLS Armoured Aluminum conductor cables conforming to IS:7098/ IS-1554 Part I (with latest amendments). Armouring strip thickness in average +5% and resistivity 14 Ohms/Kms (Max) as per IS-3975l. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. 4 core 4 sqm

Supply, Laying, Testing and Commissioning of 1.1 kV grade 3Cx10sqmmm stranded XLPE (above 6sqmm) / Class A PVC insulated(below 6 sq.mm), FRLS Armoured Copper conductor cables conforming to IS:7098/ Part I (with latest amendments) laid on wall / ceiling / trench / cable rack with the proper clamping,etc as required. The cost of the nylon tie and overlapping GI strip shall be included in the cost of installation. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. Inner sheath: Extruded PVC only for Multicore, Outer sheath: Extruded Type ST2 PVC with FRLS, Armour: Galvanized Steel strip/Wire for multicore with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Laying, Testing and Commissioning of 1.1 kV grade 4Cx4sqmmm stranded XLPE (above 6sqmm) / Class A PVC insulated(below 6 sq.mm), FRLS Armoured Copper conductor cables conforming to IS:7098/ Part I (with latest amendments) laid on wall / ceiling / trench / cable rack with the proper clamping,etc as required. The cost of the nylon tie and overlapping GI strip shall be included in the cost of installation. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. Inner sheath: Extruded PVC only for Multicore, Outer sheath: Extruded Type ST2 PVC with FRLS, Armour: Galvanized Steel strip/Wire for multicore with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Laying, Testing and Commissioning of 1.1 kV grade 3Cx6sqmmm stranded XLPE (above 6sqmm) / Class A PVC insulated(below 6 sq.mm), FRLS Armoured Copper conductor cables conforming to IS:7098/ Part I (with latest amendments) laid on wall / ceiling / trench / cable rack with the proper clamping,etc as required. The cost of the nylon tie and overlapping GI strip shall be included in the cost of installation. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. Inner sheath: Extruded PVC only for Multicore, Outer sheath: Extruded Type ST2 PVC with FRLS, Armour: Galvanized Steel strip/Wire for multicore with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Laying, Testing and Commissioning of 1.1 kV grade 3Cx4sqmmm stranded XLPE (above 6sqmm) / Class A PVC insulated(below 6 sq.mm), FRLS Armoured Copper conductor cables conforming to IS:7098/ Part I (with latest amendments) laid on wall / ceiling / trench / cable rack with the proper clamping,etc as required. The cost of the nylon tie and overlapping GI strip shall be included in the cost of installation. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. Inner sheath: Extruded PVC only for Multicore, Outer sheath: Extruded Type ST2 PVC with FRLS, Armour: Galvanized Steel strip/Wire for multicore with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Laying, Testing and Commissioning of 1.1 kV grade 3Cx2.5sqmmm stranded XLPE (above 6sqmm) / Class A PVC insulated(below 6 sq.mm), FRLS Armoured Copper conductor cables conforming to IS:7098/ Part I (with latest amendments) laid on wall / ceiling / trench / cable rack with the proper clamping,etc as required. The cost of the nylon tie and overlapping GI strip shall be included in the cost of installation. Cable identification labels at both ends clearly mentioning the cable specs & also at appropriate intervals along the cable route should be provided. Inner sheath: Extruded PVC only for Multicore, Outer sheath: Extruded Type ST2 PVC with FRLS, Armour: Galvanized Steel strip/Wire for multicore with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 X 10 sq. mm (22mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 120 sq. mm (45mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 150 sq. mm (50mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm (57mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 240 sq. mm (62mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3½ X 400 sq. mm (82mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

End Termination Supply, Installation, Testing and Commissioning of 3Cx10sqmm Ar. Compression type cable gland, copper lugs for copper cables, insulation tape, anti corrosive paste, brass clamps for gland earthing with 14 SWG copper wire to connect to nearest earth flat. Gland type : Brass with nickel plated double compression Sealing Ring : Natural rubber for indoor, Neoprene for Outdoor with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

End Termination Supply, Installation, Testing and Commissioning of 4Cx4sqmm Ar. Compression type cable gland, copper lugs for copper cables, insulation tape, anti corrosive paste, brass clamps for gland earthing with 14 SWG copper wire to connect to nearest earth flat. Gland type : Brass with nickel plated double compression Sealing Ring : Natural rubber for indoor, Neoprene for Outdoor with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

End Termination Supply, Installation, Testing and Commissioning of 3Cx6sqmm Ar. Compression type cable gland, copper lugs for copper cables, insulation tape, anti corrosive paste, brass clamps for gland earthing with 14 SWG copper wire to connect to nearest earth flat. Gland type : Brass with nickel plated double compression Sealing Ring : Natural rubber for indoor, Neoprene for Outdoor with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

End Termination Supply, Installation, Testing and Commissioning of 3Cx4sqmm Ar. Compression type cable gland, copper lugs for copper cables, insulation tape, anti corrosive paste, brass clamps for gland earthing with 14 SWG copper wire to connect to nearest earth flat. Gland type : Brass with nickel plated double compression Sealing Ring : Natural rubber for indoor, Neoprene for Outdoor with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

End Termination Supply, Installation, Testing and Commissioning of 3Cx2.5sqmm Ar. Compression type cable gland, copper lugs for copper cables, insulation tape, anti corrosive paste, brass clamps for gland earthing with 14 SWG copper wire to connect to nearest earth flat. Gland type : Brass with nickel plated double compression Sealing Ring : Natural rubber for indoor, Neoprene for Outdoor with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Part-C - Cable Trays

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer" (galvanisation not less than 50 microns) with perforation not more than17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer" (galvanisation not less than 50 microns) with perforation not more than17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 600 mm width X 75 mm depth X 2.0 mm thickness

Supply and installing 300mm x 50mm Ladder type - Hot Dip Galvanised weldless construction, factory assembled bolted rung type, Hot dip galvanised GI as per IS 2629, made out of Hot Rolled steel sheets of 1.6mm thickness conforming to IS 1079 Grade O. Finish shall be Hot Dip Galvanized 65 Microns for 1.6mm and above thick material conforming to IS 2629. Couplers shall be 2.0mm thick (Hot Dip Galvanized), Plate type with 4 holes. pre galvanized steel runner and seated rungs. Including cable support system, including horizontal and vertical bends ,anchor fastner and C channel,GI bolt, reducers, tees, cross members at 300 mm interval and other accessories as required and duly suspended from the ceiling with fabricated MS angle supports at 1000 mm interval, etc as required. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and installing 600mm x 75mm Ladder type - Hot Dip Galvanised weldless construction, factory assembled bolted rung type, Hot dip galvanised GI as per IS 2629, made out of Hot Rolled steel sheets of 2.0mm thickness conforming to IS 1079 Grade O. Finish shall be Hot Dip Galvanized 65 Microns for 2.0mm and above thick material conforming to IS 2629. Couplers shall be 2.5mm thick (Hot Dip Galvanized), Plate type with 4 holes. pre galvanized steel runner and seated rungs. Including cable support system, including horizontal and vertical bends ,anchor fastner and C channel,GI bolt, reducers, tees, cross members at 300 mm interval and other accessories as required and duly suspended from the ceiling with fabricated MS angle supports at 1000 mm interval, etc as required. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and installing 1000mm x 75mm Ladder type - Hot Dip Galvanised weldless construction, factory assembled bolted rung type, Hot dip galvanised GI as per IS 2629, made out of Hot Rolled steel sheets of 2.0mm thickness conforming to IS 1079 Grade O. Finish shall be Hot Dip Galvanized 65 Microns for 2.0mm and above thick material conforming to IS 2629. Couplers shall be 2.5mm thick (Hot Dip Galvanized), Plate type with 4 holes. pre galvanized steel runner and seated rungs. Including cable support system, including horizontal and vertical bends ,anchor fastner and C channel,GI bolt, reducers, tees, cross members at 300 mm interval and other accessories as required and duly suspended from the ceiling with fabricated MS angle supports at 1000 mm interval, etc as required. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and Fabrication and installation of MS items such as Tees/ angles/ channels etc. on floor/ ceiling/ wall including necessary civil work such a s grouting, finishing etc. and painting with two coats of primer and two coats of enamel paint as required.

Part-D - Wiring

Supply and laying of 20mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes, couplers, saddles screws etc ,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification. as detailed in technical specification.

Supply and laying of 25mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes, couplers, saddles screws etc ,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification. as detailed in technical specification.

Supply and laying of 32mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes, couplers, saddles screws etc ,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification. as detailed in technical specification.

Supply and laying of 20mm dia corrugated good quality flexible PVC conduit along with adaptors and all other accessories as required complete.

Supply and laying of 22mm ISI marked casing and capping including all accessories like elbows, tees, junction boxes screws etc in surface as required complete.

Supply and laying of 25mm ISI marked casing and capping including all accessories like elbows, tees, junction boxes screws etc in surface as required complete.

Supply and drawing of of 1.5sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification.

Supply and drawing of of 2.5sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification.

Supply and drawing of of 4 sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification.

Supply and drawing of of 6 sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification.

Supply and drawing of 3C 1.5 sq. mm. FRLSH PVC insulated copper conductor stranded cable in existing conduit

Supply and Fixing 6A modular type one way switch with suitable front plate & metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of 6A modular type two way switch with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of 6A modular type, 5pin plug socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of 16A modular type one way switch with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of 16A modular type ,5pin plug socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of multistandard socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required , making good the surface etc. as required complete.

Supply and Fixing of surface or recess mounted type 15A SP weatherproof one way switch with IP66 enclosure including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of blanking plate in existing switch box as required complete.

Fixing of modular stepped type electronic fan regulator with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of bell push with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supply and Fixing of 230V, one module buzzer alongwith backbox, front cover on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm thick steel conduit, aluminium cast back plate and brass holder complete, including wiring the down rod with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and painting etc. as required.

Supply, fixing, testing and commissioning of 1No. 25A, 240V, Electronic type Keycard with, Credit Card Size Key Fob, suitable size front plate and metal box in recessed system. The job include terminations through proper jointing materials all complete civil works like Chipping Chasing & rough plastering and all other necessary Accessories for the following Make of Insulated wires shall be as per approved make

Supply, fixing, testing and commissioning of DND & MMR internal & External Unit, suitable size front plate and metal box in recessed system. The job include terminations through proper jointing materials all complete civil works like Chipping Chasing & rough plastering and all other necessary Accessories for the following Make of Insulated wires shall be as per approved make

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Weather Proof Junction Boxes Supply, Installation, Testing and Commissioning IP 65 EnyCase DK Thermoplastic Cable Junction Boxes(88mm x 88mm x 53mm) with terminal Blocks suitable for the termination of 3Cx2.5 Sqmm Ar./Un.Ar. Cable, Sealing device & all necessary fixing Accesorries, mounting on 150mm Ht. with 25mmx25mmx3mm angle above the Ground level. Cost should include for supproting from ground level with supply and fixing of 20X3mm angle with 2 coats of anti rusting primer & epoxy enamel paint.

Part-E - DB Supply

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 16 KA,TP MCCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 16 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, Single pole, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, Double pole, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, Triple pole, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, Triple pole and Neutral, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing 40A rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63A rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40A rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63A rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 25A rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40A rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 25A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing & Fixing MV Danger notice Plate of 200x150mm made of mild steel, at least 2mm thick & vitreous enameled white on borh sides, and with inscription in single Red color on front side as required.

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. For 8 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. For 10 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. For 14 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 4 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 6 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required.

Part-E - Earthing

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supply and laying following sizes of 25mmx3mm Copper Earth strips with PVC Sleeves including supply of fixing clamps and accessories when laid inside the building and inclusive of excavation & refilling of earth when laid outside the building and interconnections with earth pit and equipment, terminations/ interconnections in an approved manner as per IS:3043 (with latest amendments) inclusive of supply of all hardwares complete as required.GI conductor joints shall be bolted and joints shall be protected with bitumen paint.Copper conductor joint shall be brazed or rivetted .The equipment connection shall be bolted using galvanized hardware or bolted by using passivated hardware.

Supply and laying following sizes of 75mmx10mm GI strips including supply of fixing clamps and accessories when laid inside the building and inclusive of excavation & refilling of earth when laid outside the building and interconnections with earth pit and equipment, terminations/ interconnections in an approved manner as per IS:3043 (with latest amendments) inclusive of supply of all hardwares complete as required.GI conductor joints shall be bolted and joints shall be protected with bitumen paint.Copper conductor joint shall be brazed or rivetted .The equipment connection shall be bolted using galvanized hardware or bolted by using passivated hardware.

Supply and laying following sizes of 50mmx6mm GI strips including supply of fixing clamps and accessories when laid inside the building and inclusive of excavation & refilling of earth when laid outside the building and interconnections with earth pit and equipment, terminations/ interconnections in an approved manner as per IS:3043 (with latest amendments) inclusive of supply of all hardwares complete as required.GI conductor joints shall be bolted and joints shall be protected with bitumen paint.Copper conductor joint shall be brazed or rivetted .The equipment connection shall be bolted using galvanized hardware or bolted by using passivated hardware.

Supply and laying following sizes of 25mmx6mm GI strips including supply of fixing clamps and accessories when laid inside the building and inclusive of excavation & refilling of earth when laid outside the building and interconnections with earth pit and equipment, terminations/ interconnections in an approved manner as per IS:3043 (with latest amendments) inclusive of supply of all hardwares complete as required.GI conductor joints shall be bolted and joints shall be protected with bitumen paint.Copper conductor joint shall be brazed or rivetted .The equipment connection shall be bolted using galvanized hardware or bolted by using passivated hardware.

Supply and laying following sizes of 25mmx3mm GI strips including supply of fixing clamps and accessories when laid inside the building and inclusive of excavation & refilling of earth when laid outside the building and interconnections with earth pit and equipment, terminations/ interconnections in an approved manner as per IS:3043 (with latest amendments) inclusive of supply of all hardwares complete as required.GI conductor joints shall be bolted and joints shall be protected with bitumen paint.Copper conductor joint shall be brazed or rivetted .The equipment connection shall be bolted using galvanized hardware or bolted by using passivated hardware.

Supply and installation 50 x 6 mm copper Earth busbar - 0.5 mtr long with necessary insulator supports with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and installation 50 x 6 mm GI Earth busbar - 0.5 mtr long with necessary insulator supports with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, laying & Terminating of following 1.1kV grade, copper conductor, PVC insulated, unarmoured, power cables. The cables shall be laid on tray / hume pipe /in ready made trenches, with nylon cable ties at every 0.5-0.75 mtr etc., as required. Rate quoted shall exclude cost of tray / hume pipe 1 Core x 6Sq. mm including Terminations

Supply and laying following sizes of GI/Copper Wire/strips including supply of fixing clamps and accessories when laid inside the building and inclusive of excavation & refilling of earth when laid outside the building and interconnections with earth pit and equipment, terminations/ interconnections in an approved manner as per IS:3043 (with latest amendments) inclusive of supply of all hardwares complete as required.GI conductor joints shall be bolted and joints shall be protected with bitumen paint.Copper conductor joint shall be brazed or rivetted .The equipment connection shall be bolted using galvanized hardware or bolted by using passivated hardware. 8 SWG GI Wire

Part-F - Miscellaneous & Safety Equipments

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 150 mm dia

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 300 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 120 mm dia (OD-120 mm & ID-103 mm nominal)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 200 mm dia (OD-200 mm & ID-175 mm nominal)

SAFETY EQUIPMENTS Electrical insulating mats made of PVC Elastomer 3mm Thick & 1 mtr wide near swichboards, etc as per direction of Engineer In charge. Mat should conform to IS 15652 Class A - suitable for safe working voltage of upto 11 kV. Test certificate to be provided with supply. Mat's top Surface should be Antiskid Dotted & Bottom Surface should be Textured for Floor Grip. Mat's top Surface should be Antiskid Dotted & Bottom Surface should be Textured for Floor Grip. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and fixing of shock treatment chart in English, Hindi & local language framed in glass framework. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and fixing of GI fire buckets with round bottom, EA comprising 4 EA.fire buckets of 9Kg capacity including supply of M.S pedestal stand with hooks suitable for holding of 4EAof fire buckets, painted with Post Office Red oil paint and letter FIRE on each bucket and filling with sand complete as required. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply of Rubber hand gloves suitable for 1.1KV. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and providing St. John make first aid box 18SWG MS sheet duly painted as approved by Indian red cross society complete with all first aid medicines. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Providing and fixing Danger Plate Danger Plates shall be provided on HV and MV equipments. MV danger notice plate shall be 200 mm x 150 mm made of mild steel at least 2 mm thick vitreous enameled white on both sides and with the descriptions in signal red colour on front side as required. Notice plates of other suitable materials such as stainless steel, brass or such other permanent nature material shall also be accepted with the description engraved in signal red colour. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply and fixing of LAMINATED Single line diagram chart duly framed with 5mm thick glasssuitable to mount on wall. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Providing and fixing in position of 9 Litres capacity foam type extinguisher (mechanical type), with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply & Fixing of MS sheet board of size 500mm x 300mm of 16 SWG with Entry Restricted To Authorised Persons Only near the Main entrance of the Substation. The lettering shall be Black painted on Yellow Back ground with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply & Installation of MS support with 2 coats of anti rusting primer & epoxy enamel paint - Approval should be taken before operating the item.

2 hour fire rated fire retardant material sealing all electrical cutouts/ducts and openings made in the slab / wall / partition to take conduits / cable trays / raceways etc as required complete with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Part- G - OC Sensor & Fans

Supplying,installation,testing an d commissioning of Passive Infrared(PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

Supplying,installation,testing and commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars / Lighting DBs for automatic switching On & OFF of street lights at sun set & sun rise or twilight(Auto ON, Auto OFF, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required. 3 output (1output per phase) and suitable for three phase supply

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Part-H - UPS Works

25KVA UPS Supply, fixing, Testing and commissioning of the following UPS System and connected works with all necessary accessories complete as required at site and as per standards. 1no. Micro Processor Based IGBT Controlled 1 x 25 KVA UPS input supply of 415 Volts + 15%, 3 Phase, 50 Hz ± 10% and an out put of 415 Volts ±1%, 3 Phase 50 ± 0.1 Hz, Input Power Factor <=0.99, Input Total Harmonic Distortion (THDi) <3%, Unity Output Power Factor @ 45deg C consisting of Rectifier, Inverter, Battery DC Circuit Breaker with necessary MS closed enclosure, Inbuilt Static BY PASS Panel (Input & output switches and Auto Static & Manual Bypass Switches), Inbuilt Copper Wounded K13 Dyn 11 Isolation Transformer @ Output side, provision for parallel integration necessary cable alley shall be provided if cable entry/exit for UPS unit is from bottom/sides and necessary hardware & software for BMS Intergration with communication port RS 485 ( Status Monitoring ), complete as required) with necessary adequate size of copper lugs etc., with necessary base channels/supports complete as required and all other necessary accessories required as per detailed specification. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Installation, Testing and Commissioning of 12V Sealed Maintenance Free Battery banks to support 25KVA UPS for 15 Minutes complete back up with intercell connectors & copper cables for I/P & O/P of UPS & Isolation Transformer, Battery Interlinks, DC Cabling from Battery to UPS, all interconnecting Copper cables (Battery bank to Battery DC Circuit breaker, Battery DC Circuit breaker to UPS, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

10 KVA UPS Supply, fixing, Testing and commissioning of the following UPS System and connected works with all necessary accessories complete as required at site and as per standards. 1no. Micro Processor Based IGBT Controlled 1 x 10 KVA UPS input supply of 415 Volts + 15%, 3 Phase, 50 Hz ± 10% and an out put of 415 Volts ±1%, 3 Phase 50 ± 0.1 Hz, Input Power Factor <=0.99, Input Total Harmonic Distortion (THDi) <3%, Unity Output Power Factor @ 45deg C consisting of Rectifier, Inverter, Battery DC Circuit Breaker with necessary MS closed enclosure, Inbuilt Static BY PASS Panel (Input & output switches and Auto Static & Manual Bypass Switches), Inbuilt Copper Wounded K13 Dyn 11 Isolation Transformer @ Output side, provision for parallel integration necessary cable alley shall be provided if cable entry/exit for UPS unit is from bottom/sides and necessary hardware & software for BMS Intergration with communication port RS 485 ( Status Monitoring ), complete as required) with necessary adequate size of copper lugs etc., with necessary base channels/supports complete as required and all other necessary accessories required as per detailed specification. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Supply, Installation, Testing and Commissioning of 12V Sealed Maintenance Free Battery banks to support 10KVA UPS for 15 Minutes complete back up with intercell connectors & copper cables for I/P & O/P of UPS & Isolation Transformer, Battery Interlinks, DC Cabling from Battery to UPS, all interconnecting Copper cables (Battery bank to Battery DC Circuit breaker, Battery DC Circuit breaker to UPS, battery stand made out of Powder Coated MS Angles with adequate supports to carry the load of the batteries. with all lead and Lifts and as directed by the Engineer-In-Charge of the work.

Part- I - Installation of Light Fixtures

Unloading, Storing, Fixing, Testing and commissioning of 4 feet Batten LED Light Fixture with necessary channels/supports, Suspension Kit complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of Circular/Square type recess/Surface monted LED Light Fixture with necessary channels/supports complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of 4 feet Linear LED Light Fixture with necessary channels/supports, Suspension Kit complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of rectangular type recess Mounted LED Zoom Light Fixture with necessary channels/supports complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of 1mtr x 3nos. LED Track Light Fixture with necessary channels/supports, Suspension Kit complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Magnetic Track Light Fixture with necessary channels/supports complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of Suspended type LED Pendant Light Fixture with necessary channels/supports complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of Suspended type LED Chandlier Light Fixture with necessary channels/supports complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED High Bay Light Fixture with necessary channels/supports, suspension kit/Chain complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Wall mounted Light Fixture with necessary channels/supports, complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Under Water Light Fixture with necessary channels/supports, complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Spike Light Fixture with necessary channels/supports, complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Floor mounted Standalone Light Fixture with necessary channels/supports, complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Table mounted Standalone Light Fixture with necessary channels/supports, complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Strip Light Fixture with aluminium Extrusion silver anodizing tracks necessary channels/supports, complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Unloading, Storing, Fixing, Testing and commissioning of LED Strip Light Fixture with necessary channels/supports, complete as required and all other necessary fixing accessories required as per detailed specification and with all lead, Lifts and as directed by the Engineer-In-Charge of the work.

Laying and Jointing PVC Pipe. Heading

Providing and fixing of 8 mm Aluminum Round Conductor With suitable Bottom section and Parallel/Horizental conductor holder stainless steel Bottom section with Ø 8.5 mm slot .

Providing & Fixing of cross universal connector: For T and cross connection, to route vertical down conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts

Providing & Fixing of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU.

Providing & Fixing of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece ).

Supply & Fixing of 1.5 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561

Supply & Fixing of 1 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561

Supply & Fixing of Lightnig counter - To count no of lightning strike & it can record the date and time of the lightning incident also tested as per IEC 62561-6.

Supply & Fixing of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized.

Providing & fixing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate.

Providing & fixing of flat conductor holder suitable for FL 30. Installed with 2 hexagonal bolts.

Providing & fixing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric.

Supply and laying of UL Listed maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 14.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 & universal clamp made of SS to connect rod with flat conductor, Earth conductivity enhancing mineral compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested, & shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system

Description of Work / Item(s)

Amount

Supply, installation, testing and commissioning BMS Workstation with following configuration :- Processor : Intel core i7 , Clock frequency 3.0 GHz, Operating system : Windows 2010 ,64 bit, RAM : 8 GB, Hard drive : HDD 1 TB, DVD , USB, Mouse, keyboard etc, 24" HD LED screen capable for 24X7 operation. The PC shall come with preloaded latest windows OS, MS office package and antivirus software complete as required.

55" Full HD LED screens, with HDMI/VGA outputs, PC inputs.LED screens should be Full high definition (Minimum 1920 x 1080) or Better should have 2 ms or better response time, Energy Star compliant & capable to operate for 24x7 operation .It shall have capablility of web browser connectivity feature, and shall come with remote control and shall have various picture mode options for data representation with all necessary fixing accessiories for viewing.

Network Laser Jet Colour Printer (A4 size) as per Specification

Supply ,Testing and Commissioning of the Software for Building Automation System as per technical Specifications. Software shall have the capacity to accommodate minimum2500 points or more and minimum 2 user license. The software shall comprise of Building Performance Management Software, Energy calculation and management software along with Maintenance software as per technical Specifications. The software shall be in open platform and freely expandble. It shall be capable of exchanging data with any IoT platform and come with advanced analytics modules.

Supply, Installation, Testing & Commissioning of Integrator/converter for Integration of the following third party systems supporting BACnet/Modbus RS485 protocol as per technical specification with all other mounting accessories and enclosures complete as required. AC Chiller (3 No) - 25 points each Pump VFD (3 nos) - 10 points each AHU Fan VFD (8 Nos) - 10 points each VAV (50 Nos) - 6 points each BTU meters (15 Nos) - 6 points each Energy meters (50 Nos) - 10 points each UPS (4 Nos) - 20 points each Water meter ( 10 Nos) - 3 points each FAS (1 no) - 700 points Heat Pump Integration

Stand alone Intelligent IP Based Indoor type DDC Controllers as per the specifications for hard wired IO points as mention in IO summary. The contractor shall decide upon the number of contollers, depending on his Controller capacity. Contractor shall furnish quantity and unit rate for each type of controller considered by him based on the IO summary . The above shall be housed in a IP54 rated housing with lockable & secure heavy Guage MS powder coated Cabinets to be supplied along with the Controllers as per specifcation.

Supply, Installation & Commissioning ofDifferential pressure switch for filter status (50-500Pa) as per technical Specification

Supply, Installation & Commissioning of Differential pressure switch for run status (20-200Pa) as per technical Specification

Supply, Installation & Commissioning of Duct Mounted Temperature + Humidity Combo Sensor (±0.3 deg C & ±3% ) as per technical Specification

Supply, Installation & Commissioning of Space CO2 Sensor (0-200ppm) with ±3% accuracy as per technical Specification

Supply, Installation & Commissioning of Duct static Pressure Sensor (0-500Pa) with +/-1% FS accuracy as per technical specification.

Supply, Installation & Commissioning of Immersion temperature Sensor (±0.3 deg C) with matching SS thermowell with all installation accessoroes complete as required as per technical Specification

4 inches

6 inches

Strap ON type temperature sensor (±0.5 deg accuracy) as per technical specification

Water line pressure sensor (±1 % Measuring Scale accuracy) as per technical specification

Level switch to monitor High and low water level as per specification

Ambient temperature and RH sensor (±0.3 deg C & ±2%) as per technical specification with suitable IP rated encloure for protection.

Ambient CO2 Sensor (0-2000ppm) with ±3% accuracy as per technical Specification with suitable IP rated encloure for protection.

Duct Mounted CO2 Sensor (0-2000ppm) with ±3% accuracy as per technical Specification

Wall mounted Hydrogen sensor with 1% Accuracy FS (0-100% LEL Hydrogen) for Battery Room with all accessories complete as required as per technical specification

Supplying and installing of 2C x 1.5 mm Shielded annealed tinned copper conductor PVC sheathed Flexible twisted pair communication cables.

Supplying and installing of 2C x 1.0 mm Shielded annealed tinned copper conductor PVC sheathed Flexible signal cables.

Supplying and installing of 4C x 1.0 mm Shielded annealed tinned copper conductor PVC sheathed Flexible signal cables.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray cable tray with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends “ ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required

100 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

Description of Work / Item(s)

Amount

Providing and fixing gun metal non- return valve of approved quality (screwed end) :50 mm nominal bore Horizontal as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing gun metal non- return valve of approved quality (screwed end) :65 mm nominal bore Horizontal as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing unplasticised PVC connection pipe of suitable pressure rating with brass unions : 30 cm length & 15 mm nominal bore as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing unplasticised PVC connection pipe of suitable pressure rating with brass unions : 30 cm length & 20 mm nominal bore as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing unplasticised PVC connection pipe of suitable pressure rating with brass unions : 45 cm length & 15 mm nominal bore as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing unplasticised PVC connection pipe of suitable pressure rating with brass unions : 45 cm length & 20 mm nominal bore as per standards, specifications and direction of the Engineer-in-charge.

Supplying, fixing, testing and commissioning of butterfly valve of PN 16 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50mm dia as per standards, specifications and direction of the Engineer-in-charge.

Supplying, fixing, testing and commissioning of butterfly valve of PN 16 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 65mm dia as per standards, specifications and direction of the Engineer-in-charge.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 50mm dia as per standards, specifications and direction of the Engineer-in-charge.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 65mm dia as per standards, specifications and direction of the Engineer-in-charge.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 50mm dia as per standards, specifications and direction of the Engineer-in-charge.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 65mm dia as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete. Internal work - Exposed on wall 32mm (NB) as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete. Internal work - Exposed on wall 40mm (NB) as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete. Internal work - Exposed on wall 50mm (NB) as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete. Concealed work, including cutting chases and making good the walls etc 15mm (NB) as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete.Concealed work, including cutting chases and making good the walls etc 20mm (NB) as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete.Concealed work, including cutting chases and making good the walls etc 25mm (NB) as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per standards, specifications and direction of the Engineer-in-charge. External work 32mm (NB)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per standards, specifications and direction of the Engineer-in-charge. External work 40mm (NB)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per standards, specifications and direction of the Engineer-in-charge. External work 50mm (NB)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per standards, specifications and direction of the Engineer-in-charge.. External work 65mm (NB)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) SDR 11 pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per standards, specifications and direction of the Engineer-in-charge.. External work 80mm (NB)

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts,nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 80mm dia as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing ball valve (brass) of approved quality, High pressure, complete : 20 mm nominal bore as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing ball valve (brass) of approved quality, High pressure, complete : 25 mm nominal bore as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating RCC chamber with water tight heavy duty C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg. 180x150 mm size P type a) GULLY TRAP 300 X 300 mm 180x150 mm size P type as per standards, specifications and direction of the Engineer-in-charge.

Constructing chamber 90x90x100 cm inside, in RCC M25 grade for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and water tight heavy duty C.I. cover with frame, i/c necessary excavation, PCC 1:2:4 and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standards, specifications and direction of the Engineer-in-charge.

Constructing chamber 120x120x100 cm inside, in M25 grade RCC for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and water tight heavy duty C.I. cover with frame, i/c necessary excavation, PCC 1:2:4 and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standards, specifications and direction of the Engineer-in-charge.

Constructing chamber 60x45x50 cm inside, in M25 grade RCC for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and water tight heavy duty C.I. cover with frame, i/c necessary excavation, PCC 1:2:4 and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standards, specifications and direction of the Engineer-in-charge.

Constructing M25 grade RCC circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top, inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, PCC 1:2:4 and making necessary channel in cement concrete, finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with CI Cover and frame (heavy duty HD 20 grade designation) 560 mm internal diameter conform ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete including excavation, centering, shuttering all complete as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing in position 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg and including outer frames & water seals as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing in position SS (304 grade) manhole cover of size 300x300mm, with provision for tile/granite inlay (heavy duty) including supply and fixing of frames in RCC, water seals, etc. as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing in position SS (304 grade) manhole cover of size 600x600mm, with provision for tile/granite inlay (heavy duty) including supply and fixing of frames in RCC, water seals, etc. as per standards, specifications and direction of the Engineer-in-charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 5000 Ltrs as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour 15 mm nominal bore with 30cm length as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour 15 mm nominal bore with 45 cm length as per standards, specifications and direction of the Engineer-in-charge.

Supply, installing, testing and commissioning of white colour European water closet wall hung mounted water closet with 'P' or 'S' trap, matching colour solid plastic seat and lid with C P brass hinges, rubber buffers, C.I / M.S Brackets, 40 mm diameter flush bend with fittings and clamps,and SS nut Bolt only considered overflow arrangements with specials and 25 mm dia mosquito proof coupling of approved design, concealed flushing cistern, front operated with cover plate, flush pipe, flush actuator, actuator plate as required. The cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per standards, specifications and direction of the Engineer-in-charge. (Considering the base price of wall hung pan with seat lid/cover as Rs.8288/-ea,).the purchase price (excluding GST ) of wall hung pan with seat lid/cover is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply, installing, testing and commissioning of FACEPLATE POLISHED CHROME The cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per specifications. specifications and direction of the Engineer-in-charge. (Considering the base price of faceplate Rs.1275/- ea) the purchase price (excluding GST ) of FACEPLATE POLISHED CHROME is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply, installing, testing and commissioning of concealed flush cistern The cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per specifications..specifications and direction of the Engineer-in-charge. (Considering the base price of concealed flush cistern system Rs.5313/- ea) the purchase price (excluding GST ) of concealed flush cistern is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply, installing, testing and commissioning of Toilet Roll Holder with Stainless Steel the cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per specifications..specifications and direction of the Engineer-in-charge. (Considering the base price of Toilet Roll Holder with Stainless Steel Rs.1083/- ea) the purchase price (excluding GST ) of concealed flush cistern is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply, installing, testing and commissioning of Angular Stop Cock with Wall Flange cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per specifications..specifications and direction of the Engineer-in-charge. (Considering the base price of Angular Stop Cock Rs.595/- ea) the purchase price (excluding GST ) of Angular Stop Cock with Wall Flange is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply, installing, testing and commissioning of white colour European water closet Floor mounted with Exposed cistern of dual flush 3/ 6 lit, with back inlet" P or S " trap by using coversion bend. The closet is mounted with suitable colour solid duroplast or scratch resistant seat and cover with special hinges to suit floor mounted water closet for soft closing for Physically Challenged Persons with cistern with necessary Grab Rails, support arms and backrest to mounted on the track (vertically and laterally) hinged rails, hand rails pan connecter bend,checknut, stopcock etc., colour solid seat and cover with polythene buffer and flap, CP flanges, CP bolts and nuts, bracket with nuts and bolts wall flanges etc.,complete, Wash Basin shall include 15mm dia CP liver operated pillar Cock with pop-up waste coupling, 32mm dia CP bottle trap with extension pipe,supporting bracket with necessary SS steel to support basin 1 No.15mm CP angle valve with 450mm long CP connection pipe and CP wall flanges all of approved make etc., all nut and Bolt are SS 304 to be considered all complete s per standards, specifications and direction of the Engineer-in-charge. (Considering the base price of European water closet Floor mounted with seat lid, flush tank & system all including as Rs.10200/-ea) The purchase price (excluding GST ) of European water closet Floor mounted is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of support arms and backrest to mounted on the track (vertically and laterally) for handicap toilet complete as required. all nut and Bolt are SS 304 to be considered all complete as per specifications..specifications and direction of the Engineer-in-charge. (Considering the base price of support arms Rs.3835/-) The purchase price (excluding GST ) of support arm is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of 35 mm dia powder coated steel grab bar.handicap toilet complete as required. all nut and Bolt are SS 304 to be considered all complete as per specifications..specifications and direction of the Engineer-in-charge. (Considering the base price of grab rails Rs.5015/- ea, ) The purchase price (excluding GST ) of support arm is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of white colour counter top wash basin.The basin is mounted over granite/C.I./ M.S Bracket with the following fittings like 32 mm CP brass full thread waste coupling, 32 mm CP brass P trap of casted type with extension pipe,Sensor tap, 450 mm long PVC inlet connecting pipes and brass/ SS nuts, 1 Nos 15 mm CP brass angular stop cock with wall flanges with extension pipe, 15mm dia SS/matte finish/matte finish angle cock, flexible inlet connection pipe G.I. expansion bolts etc., complete including silicon sealant. Flow rate 1.5 Lts/min all nut and Bolt are SS 304 to be considered all complete as per standards, specifications and direction of the Engineer-in-charge. (Considering the base price of wash basin as Rs.3987/- ea).The purchase price (excluding GST ) of wash basin is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of Sensor Faucet AUTOMATIC SENSOR TAP with DC /AC electrcal cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt to be considered all complete as per specifications..specifications and direction of the Engineer-in-charge. (Considering the base price of sensor tap Rs.4724/- ea). The purchase price (excluding GST ) of sensor tap is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of BOTTLE TRAP 350MM including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of bottle trap Rs.1148/- ea). The purchase price (excluding GST ) of bottle trap is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of Waste coupling 32mm Size Half Thread with 80mm height cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per specifications and direction of the Engineer-in-charge. (Considering the base price of Waste coupling Rs.340/- ea). The purchase price (excluding GST ) of Waste coupling is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning sink with single bowl and without drain board manufactured from 8 mm thick stainless steel, 18 G high grade indestructable chrome nickel steel with top quality polish, 1 no. 50 mm dia CP waste coupling, with 1 no. 50 mm dia CP flexible with extension pipe, 15 mm dia CP sink cock with swivel spout wall mounted type and necessary wall flanges etc., complete. Size of sink : 900 x 450mm all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of sink with single bowl and without drain board Rs.4118/- ea). The purchase price (excluding GST ) of sink with single bowl and without drain board is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of CP flexible with extension pipe C.P. Flexible Connection Pipe, "Elegant", L-1000mm, 15mm (1/2") include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges,all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of CP flexible with extension pipe Rs.396/- ea). The purchase price (excluding GST ) of CP flexible with extension pipe is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of CP sink cock cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges, SS/matte finish crutch, nozzle etc., complete. all nut and Bolt are SS 304 to be considered all complete as per specifications.. all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of CP sink cock Rs.1326/- ea). The purchase price (excluding GST ) of CP sink cock is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, Installing, testing and commissioning of approved make 15mm SS/matte finish/ polymer/ powder coated health faucet with flexible tube 1.0m long, SS/matte finish crutch, nozzle etc., complete. all nut and Bolt are SS 304 to be considered all complete as per specifications.and direction of the Engineer-in-charge. (Considering the base price of health faucet with flexible tube Rs.791/- ea). The purchase price (excluding GST ) of health faucet with flexible tube is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply and fixing of Winter white colour vitreous china Large Flat Back Urinal PATIO TOUCHLESS URINAL, WATERSAVING of size of approved make with inbuilt Sensor, battery operated. Stainless steel grating should be installed over the fabricated PE floor trap below the urinal bowl, complete with C.I. Bracket fixing to wall dado with required materials like teak wood plugs packing pieces, screw nails etc, PPR Bottle trap , SS/matte finish Spreader, Pipe, SS/matte finish Dome Coupling etc. complete, testing and commissioning the installation. connecting the urinal with waste pipe, trap etc. complete. all nut and Bolt are SS 304 to be considered (pre and post flush) all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of Large Flat Back Urinal PATIO TOUCHLESS URINAL Rs.9010/- ea). The purchase price (excluding GST ) of Large Flat Back Urinal PATIO TOUCHLESS URINAL is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning approved make concealed stop cock 13mm with wall flange all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of concealed stop cock Rs.425/- ea). The purchase price (excluding GST ) of concealed stop cock is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Providing and fixing of 15mm dia SS/matte finish/ polymer/ powder coated Bib cock with SS/matte finish wall flange and accessory .all nut and Bolt are SS 304 to be considered all complete as per specifications.and direction of the Engineer-in-charge. (Considering the base price of Bib cock Rs.723/- ea). The purchase price (excluding GST ) of Bib cock is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply and fixing of brass/ss/matte finish Coat hook with all necessary screw fitting complete fittings.cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges, SS/matte finish crutch, nozzle etc., complete. all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of Coat hook Rs.532/- ea). The purchase price (excluding GST ) of Coat hook is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply and fixing of Soap Dispenser And Holder With Frosted Glass Bottle In Polished Chrome with all necessary screw fitting complete fittings.cost shall include painting of fittings and brackets, cutting and making good the wall and floor wherever required, including cost of materials, labour including lead and lift charges, SS/matte finish crutch, nozzle etc., complete. all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of Soap Dispenser And Holder With Frosted Glass Bottle Rs.1530/- ea). The purchase price (excluding GST ) of Soap Dispenser And Holder With Frosted Glass Bottle is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supply and fixing of Stainless Steel White Automatic Hand Dryer Machine, with all necessary screw fitting complete fittings.labour including lead and lift charges, SS/matte finish crutch, nozzle etc., complete. all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of Automatic Hand Dryer Machine, Rs.7225/- ea). The purchase price (excluding GST ) of Automatic Hand Dryer Machine, is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Providing and fixing CP towel rack/ rod with brackets fixed to the wall with CP brass screws complete as per standards, specifications and direction of the Engineer-in-charge. (Considering the base price of CP towel rack/ rod with brackets as Rs.1296/-ea, ) The purchase price (excluding GST ) of CP towel rack/ rod with brackets, is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of approved make SHOWERHEAD with all necessary screw fitting and complete fittings. all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of SHOWERHEAD, Rs.1445/- ea). The purchase price (excluding GST ) of SHOWERHEAD, is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of approved make SHOWER ARM with all necessary screw fitting and complete fittings. all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of SHOWER ARM, Rs.2295/- ea). The purchase price (excluding GST ) of SHOWER ARM, is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of approved make AUTOSENSE TH REC B&S UNIVERSAL TRIM with all necessary screw fitting and complete fittings. all nut and Bolt are SS 304 to be considered all complete as per specifications.and direction of the Engineer-in-charge. (Considering the base price of AUTOSENSE TH REC B&S UNIVERSAL TRIM Rs.3035/- ea). The purchase price (excluding GST ) of AUTOSENSE TH REC B&S UNIVERSAL TRIM is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of approved make AUTOSENSE PLUS 235 THERMOSTAT VALVE with all necessary screw fitting and complete fittings. all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of AUTOSENSE PLUS 235 THERMOSTAT VALVE Rs.1920/- ea). The purchase price (excluding GST ) of AUTOSENSE PLUS 235 THERMOSTAT VALVE is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, installing, testing and commissioning of approved make BATH SPOUT W DIVERTER with all necessary screw fitting and complete fittings. all nut and Bolt are SS 304 to be considered all complete as per specifications. and direction of the Engineer-in-charge. (Considering the base price of BATH SPOUT W DIVERTER Rs.2423/- ea). The purchase price (excluding GST ) of BATH SPOUT W DIVERTER is mentioned in base price and any deviation plus or minus the purchase price will be adjusted (paid extra or deducted ) at the time of billing

Supplying, fixing and testing 6kg/cm2 PVC soil, waste , vent (SWR) confirming to IS13592 : 1990, type B with solvent joint inclusive of all necessary specials like multi floor traps (50mm water seal), bends 45 or 90 degree, 'Y's, tees, offsets, junctions, couplers screw type caps with rubber rings for cleanout pipe ends, etc., Running in the sunken slabs slabs/fixed on walls or on . All suspenders, saddles, pipe packs are to be quoted separately under relevant items.All including internal Toilet.All supports shall be painted with anti-corrosive paints to avoid corrosion. 50mm dia

Supplying, fixing and testing 6kg/cm2 PVC soil, waste , vent (SWR) confirming to IS13592 : 1990, type B with solvent joint inclusive of all necessary specials like multi floor traps (50mm water seal), bends 45 or 90 degree, 'Y's, tees, offsets, junctions, couplers screw type caps with rubber rings for cleanout pipe ends, etc., Running in the sunken slabs slabs/fixed on walls or on . All suspenders, saddles, pipe packs are to be quoted separately under relevant items.All including internal Toilet.All supports shall be painted with anti-corrosive paints to avoid corrosion. 75mm dia as per standards, specifications and direction of the Engineer-in-charge.

Supplying, fixing and testing 6kg/cm2 PVC soil, waste , vent (SWR) confirming to IS13592 : 1990, type B with solvent joint inclusive of all necessary specials like multi floor traps (50mm water seal), bends 45 or 90 degree, 'Y's, tees, offsets, junctions, couplers screw type caps with rubber rings for cleanout pipe ends, etc., Running in the sunken slabs slabs/fixed on walls or on . All suspenders, saddles, pipe packs are to be quoted separately under relevant items.All including internal Toilet.All supports shall be painted with anti-corrosive paints to avoid corrosion. 110mm dia as per standards, specifications and direction of the Engineer-in-charge.

Supplying, fixing and testing 6kg/cm2 PVC soil, waste , vent (SWR) confirming to IS13592 : 1990, type B with solvent joint inclusive of all necessary specials like multi floor traps (50mm water seal), bends 45 or 90 degree, 'Y's, tees, offsets, junctions, couplers screw type caps with rubber rings for cleanout pipe ends, etc., Running in the sunken slabs slabs/fixed on walls or on . All suspenders, saddles, pipe packs are to be quoted separately under relevant items.All including internal Toilet.All supports shall be painted with anti-corrosive paints to avoid corrosion. 160mm DIA as per standards, specifications and direction of the Engineer-in-charge.

Supplying, fixing and testing 6kg/cm2 PVC soil, waste , vent (SWR) confirming to IS13592 : 1990, type B with solvent joint inclusive of all necessary specials like multi floor traps (50mm water seal), bends 45 or 90 degree, 'Y's, tees, offsets, junctions, couplers screw type caps with rubber rings for cleanout pipe ends, etc., Running in the sunken slabs slabs/fixed on walls or on . All suspenders, saddles, pipe packs are to be quoted separately under relevant items.All including internal Toilet.All supports shall be painted with anti-corrosive paints to avoid corrosion.200mm dia as per standards, specifications and direction of the Engineer-in-charge.

Supply and fixing PVC Multi floor trap (anti cockroach & anti foul smell trap with cup) and with frame and cover (110 mm x 110 mm square) P trap of 75mm with boss connection which is watersealed. Outlet fixed on a bed of cement concrete with self cleansing design with or without vent arm including cutting and making good the walls and floors., complete as per standards, specifications and direction of the Engineer-in-charge.

Supply and fixing SS (304 grade) hinged trap cover of 6mm thick and having perforations with rim of size 125 x 125 mm ( to match multitrap of 110 x 110 mm) including setting in floor with suitable adhersive, filler, and epoxy as per standards, specifications and direction of the Engineer-in-charge.

Supply and fixing SS (304 grade) hinged tile insert trap cover with drain facility including setting in floor of size 125 x 125 mm ( to match multitrap of 110 x 110 mm) with suitable adhersive, filler, and epoxy as per standards, specifications and direction of the Engineer-in-charge.

Providing and fixing of brass body nickel plated automatic air release valves with brass splindle, NBR(nitrile butadiene Rubber) and join franite elastomer, stainless steel spring polypropylenic float at the top most points of watersupply distribution risers in the shafts having pressure of 10kg/cm2. 20mm dia

Supplying installing , testing and commissioning of internally mouldded rubber lined body Butterfly valve with pressure rating of 10kg/cm2 including actuator of motorised ON/OFF type with suitable transformer. valve to be provided with additional shoe piece for easy connection of pipe. 80mm dia as per standards, specifications and direction of the Engineer-in-charge.

Supplying installing , testing and commissioning approved make CI water metre with flow sensor is digital flow meter RSIP compatible with BMS ( operation or monitor) applications with Low-pressure drop Flow range: +/- 200 slm (bidirectional) Accuracy 1.5% m.v. (typical) Very fast update time Fully calibrated & temperature compensated Low zero drift bulk enclosed type with metallic gears flanged ends able to record the flow under pressure with flow indications complete. 50mm dia as per standards, specifications and direction of the Engineer-in-charge.

Supply, installation, testing and commissioning of heavy duty copper float valve matching 80mm NB pipe size confirming to IS: 1703 complete as per standards, specifications and direction of the Engineer-in-charge.

Providing and laying non-pressure NP 3 class RCC pipes with collars jointed / Socket & Spigot with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. a) 300 mm dia RCC pipe as per standards, specifications and direction of the Engineer-in-charge.

Supplying installing , testing and commissioning of Air to Water heat pump having heating capacity of as below manction , water inlet and outlet temperature of 50/55 Deg C on condenser side, 36°C ambient air on Evaporator side with heating COP > 3. Condenser heat exchanger shall be shell & tube type, Evaporator shall be aluminium finned copper tube type and Refrigerant shall be HR417A, complete with expansion valve, standalone control unit. Air Source Heat Pump: 30 kW Heating Capacity. Shall include suitable number of Pressure Gauge, Temperature Gauge, Temperature sensor port, safety valves. Pumps shall have Cast Iron body, Stainless Steel impeller and SS shaft with Mechanical seal, suitable for automatic / manual operation. Hot Water Pumps shall have design temperature rating of 90 Deg C. Including MS structured frame. Heat Pump circulation pumps : 5 m3/hr.,20 mtrs head. Electrical Control Panel Medium Voltage floor mounting Cubicle Type Control Panel made out of 16 /18 SWG MS, Powder coated, suitable for 415 V, 3 Phase, 50 Hz Power Distribution System. Panel shall consists of Power circuit for heat pump & Pumps . Necessary isolation switches for heat pump and overload relays for circulation pumps. The panel shall include energy meter with appropriate CTs. Power & Control Panel for Heat pump and pumps. Power & Control Cabling -(Incomer panel to our panel shall be in electrical scope).all complete as per standards, specifications and direction of the Engineer-in-charge.

Supplying installing , testing and commissioning of Hot Water storage Tank Permeate water produced is at atmospheric pressure, hence for further treatment it is collected in storage tank. Storage tank should be made up of SS 304 0.8mm thikness (easy tank) and 450 mm diameter manhole (manhole only for storage tank). The shell and dish end plate thickness shall be 6 mm. The tank shall be designed for 3 kg/sq.cm working pressure and test pressure of 4 kg/sq.cm. The tank must be complete Nozzles for safety valves, air vent valve,pressure gauge, temperature gauge, thermo-couple provision at top & bottom of the tank. 5000 Litres Storage tank as per standards, specifications and direction of the Engineer-in-charge.

Supplying, installing, testing and commissioning of MONOBLOCK type pumps (one working & one standby) for pumping water from existing sump to water treatment plant.The pump shall be coupled to the adequate H.P. electrical motor, mounted on a common base frame. The rate quoted shall be inclusive of: Suitable control panel indoor wall mounting type. Industrial type electronic liquid level controllers with stainless steel probes / sensors or float switch for automatic operation. 1no. pressure gauge 4" dial with valve tee and fittings. Alarm indication with signal in the event of pump failure etc. The pump shall be suitable for handling silt and muck in the water. The Control Panel shall be designed and fabricated in such a way that it shall be compatible to BMS. Starter Panel shall be included. Conduits to carry the cables shall be included. Cable connection from starter panel and from starter panel to the pump and armoured cable shall be included. The pump shall be suitable for the following requirements: Discharge - 2.0 cum/hr (2.5 LPS) Head - 25 Mtr all complete as per standards, specifications and direction of the Engineer-in-charge.

Supplying, installing, testing and commissioning of MONOBLOCK type pumps for pumping water from Water body circulation pump.The pump shall be coupled to the adequate H.P. electrical motor, mounted on a common base frame. The rate quoted shall be inclusive of: Suitable control panel indoor wall mounting type. Industrial type 1no. pressure gauge 4" dial with valve tee and fittings.electronic liquid level controllers with stainless steel probes / sensors or float switch for automatic operation. Alarm indication with signal in the event of pump failure etc. The pump shall be suitable for handling silt and muck in the water. The Control Panel shall be designed and fabricated in such a way that it shall be compatible to BMS. Starter Panel shall be included. Conduits to carry the cables shall be included. Cable connection from starter panel and from starter panel to the pump and armoured cable shall be included. The pump shall be suitable for the following requirements: Discharge - 16.0 cum/hr (6.5 LPS) Head - 25 Mtr all complete as per standards, specifications and direction of the Engineer-in-charge.

Description of Work / Item(s)

Abstract Sheet

BOQ1-Buyback

BOQ2-Interior works

BOQ3-ELV works

BOQ4-HVAC works

BOQ5-Fire protection works

BOQ6-Electrical works

BOQ7-BMS works

BOQ8-PHE works

Artizen Interiors Pvt Ltd

OCEAN INTERIORS LIMITED

Artizen Interiors Pvt Ltd

Godrej and Boyce Manufacturing Company Limited

Artizen Interiors Pvt Ltd

OCEAN INTERIORS LIMITED

OCEAN INTERIORS LIMITED

Artizen Interiors Pvt Ltd

OCEAN INTERIORS LIMITED

Artizen Interiors Pvt Ltd

Artizen Interiors Pvt Ltd

OCEAN INTERIORS LIMITED

Artizen Interiors Pvt Ltd

OCEAN INTERIORS LIMITED

OCEAN INTERIORS LIMITED

Artizen Interiors Pvt Ltd

OCEAN INTERIORS LIMITED

Artizen Interiors Pvt Ltd