8298 REPAIRS TO WOODEN JOINERY LIKE DOORS, WINDOWS, VENTILATORS, GLASS PANELS AND OTHER CONNECTED ITEMS AND CERTAIN MISCELLANEOUS WORKS IN TECHNICAL AND RESIDENTIAL AREA AT NSTL UNDER AGE (I) RnD NSTL, VISAKHAPATNAM

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc. 1.5 sq.m but not exc. 4.0 sq.m each all as directed

Taking down chowkats or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 sq.m each all as directed

Taking down shutters of any description not exc. 1.0 sq.m each all as directed.

Taking down shutters of any description exc. 1.0 sq.m but not exc. 2.0 sq.m each all as directed.

Taking down shutters of any description, not exc. 1.0 sq.m each including easing and adjusting and refixing the shutters in same opening including renewal of unserviceable screws, etc. complete all as specified and directed.

Taking down shutters of any description, exc. 1.0 sq.m but not exc. 2.0 sq.m each including easing and adjusting and refixing the shutters in same opening including renewal of unserviceable screws, etc. complete all as specified and directed.

M&L for attending to petty repair job to joinery items such as easing/ adjusting of wooden/ aluminium doors in-situ, fixing of hanging doors, adjustment of jammed doors, refixing of beadings, refixing of builders hardware, making good door closers etc. including necessary screws, nails, wooden plugs etc. as required at site to make the joinery functional complete as specified and directed by Engineer In Charge. [Note : (i) Each repair job shall be measured as one job. (ii) Job involving replacement of builders hardware shall not be measured under this item].

S&F solid PVC door frame of size 50mm x 47mm made out 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening as per specification & drawing shown on Sl. Page No. 160 of SSR Part-II-2010 complete all as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing shown on Sl. Page No. 157 of SSR Part-II-2010 complete all as directed.

S&F MS Butt hinges 100mm long medium weight cold rolled and fixed

S&F aluminium anodized barrel tower bolt of size 150 mm long of extruded section

S&F extruded aluminium alloy handles fabricated type of size 125mm.

S&F 200mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

M&L for 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L for 2nd class hardwood 35 mm thick plain, framed, paneled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, fitted to chowkats complete all as specified and directed.

M&L for 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc. size of members as specified in SSR Pt-I, section 8 clause 8.24 (a) complete all as directed.

M&L for 32mm thick flush shutter solid core construction with block board core and plywood face panels commercial type on both sides all as specified

S&F MS Butt hinges 125mm long medium weight cold rolled and fixed

S&F aluminium anodized barrel tower bolt of size 200 mm long of extruded section

S&F extruded aluminium alloy handles fabricated type of size 150mm.

S&F 300mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

S&F 300mm long mild steel ordinary rat tail rod pattern spring including roller and roller plate complete fixed in repairs all as specified and directed by Engineer-in-Charge

M&L for 30mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc. size of members as specified in SSR Pt-I, section 8 clause 8.24 (b) complete all as directed.

S&F aluminium anodized barrel tower bolt of size 125 mm long of extruded section

S&F aluminium plate type-II Gate and shutter, hooks and eyes 150mm.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F 4.8mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden beads in squares not exc. 0.5 sq.m each pane.

S&F 4.8mm thick sheet glass, ordinary quality, frosted on one side and glazing with oil putty/ wooden beads in squares not exc. 0.5 sq.m each pane.

M&L for cutting holes in brick walls built in cement mortar for inserting hold fast and making good dismantled portion with cement mortar 1:3 or PCC 1:3:6 type C1 exc. half brick wall but n.exc. one brick wall complete all as specified.

All as per Item No. 29 herein before but in stone walls built in cement mortar

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S&F in repairs Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats. (Minimum weight 190gms) all as specified and as directed

S&F Mortise lock, brass vertical type, size 100mm, 4 levers all as specified. [Make: Godrej/ Link/ Dorset]

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads.

S&F Solar control film 50 micron thick, reflective type sticked to glass panes as per instructions of manufacturer complete all as specified.

S&F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F in repairs aluminium anodized barrel tower bolt of size 200 mm long of extruded section

S&F in repairs aluminium anodized barrel tower bolt of size 150 mm long of extruded section

S&F in repairs aluminium anodized barrel tower bolt of size 125 mm long of extruded section

S&F in repairs extruded aluminium alloy handles fabricated type of size 150mm

S&F in repairs extruded aluminium alloy handles fabricated type of size 125mm

S&F in repairs 300mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

S&F in repairs 200mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

S&F in repairs aluminium plate type-II Gate and shutter, hooks and eyes 150mm.

S&F in repairs 300mm long mild steel ordinary rat tail rod pattern spring including roller and roller plate complete fixed in repairs all as specified and directed by Engineer-in-Charge

S&F in repairs 25mm thick Veneered particle boards interior grade, solid core, general purposes type, with face veneers of type 'BB', fixed with screws to timber frame work all as specified and as directed.

S&F teak wood lipping 25mm wide and 6mm thick fixed to edges of particle board with nails all as specified.

S&F Continuous (piano) hinges, mild steel, bright finish or electro-galvanized, width of flaps (when open) 30mm all as specified.

S&F in repairs Continuous (piano) hinges, mild steel, bright finish or electro-galvanized, width of flaps (when open) 30mm all as specified.

S&F magnetic catch for cup board shutters fixed with screws complete all as specified and directed by Engineer-in-Charge

S&F 2nd class hardwood plain fillets/beading exc. 6 sq.cm not exc 13 sq.cm, square/ rectangular, rounded on one edge or face, fixed with screws and wrought all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hard wood boarding 25mm thick planed on both sides with butt joints fixed with screws complete including dismantling existing decayed boarding all as specified

S&F 100mm hasp and staple, safety type aluminium anodized hinge pin including bolt to hinge plate and fixed with screws all as specified and directed by Engineer-in-Charge

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and as directed.

M&L for preparation of new steel surfaces of any description, not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified.

S&F in repairs door closer hydraulically regulated, designation No. 2 universal type with aluminium (Die cast) body, suitable for door shutters of weight up to 60 kg and fixed all as specified. [Make: Everite/ Kelwyn/ Universal]

Removing mild steel grills from existing windows and refixing the same after carrying out repairs to external side of windows all as directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc. complete (minimum thickness of powder coating 50 micron) all as specified.

M&L for powder coated aluminium door shutters, with aluminium sections of minimum 3mm thick and weight not less than 2.05kg/m for side rails, 2.646kg/m for top & bottom rails and 3.116kg/m for lock rail, including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screw etc. complete all as specified and directed by Engineer-in-charge (minimum thickness of powder coating 50 micron). Note: Panel/ glass inserts shall be measured and paid separately

M&L for 12 mm thick veneered decorative plywood grade 1 (with BWR resin) with decorative veneers on both faces as in shutters and kitchen cupboards shutters complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick in CM 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing surfaces finished even and smooth without using extra cement

B SRINIVAS

ANJALI CONSTRUCTIONS

Sai Srija Constructions

SRI SRK ENGINEERS