16/2022-23(EDCR) Increasing load capacity of overloaded transformer by Separate transformer and replacement of Jarjar wire under EDD-Milak, Rampur

Amount

Carriage of the following material from Store Centre, Rampur to work site including loading & unloading.

8.5 Mtr long PCC Pole.

ACSR Weasal Conductor

Scrap GI Wire and Scrap ACSR Weasal Conductor( Site to store) and other line material etc.

AB Cable 3x50+1x35+1x16

Cartage of Healty Transformer from store to site, dismantling of HT & LT connection & replace of follwoing capacity T/F from substation double poles/plinth by Healthy transformer(including connection) and loading and unloading with associated work at both ends within 70 kms.

Increasing load capacity of overloaded by Separate 10 KVA trasnformer

Increasing load capacity of overloaded by Separate 63 KVA trasnformer

a) Single support Excavation of foundation Pit in size of 75x45cm having depth of 1/6th of the full length of the support(pole), providing and laying of stone pad (300x300x75 mm) in the Bottom of the pit. Erection of support(pole) complete with fixing of 11 KV V-type cross-Arms and other accessories by providing clamps made of MS flat of size 65x65xc6 mm with Nuts & Bolts, as per RESPO Norms.

8.5 Mtr long PCC Pole

b) Double pole structure Excavation of foundation pit in size of 75x45cm having depth of 1/6th of the full length of the support(pole)Erection of support(pole) complete with providing and fixing of all clamps made of MS flat of size 75x8 mm. an other accessories . The work includes fabrication work and fixing of cross bracing sets 3.5 Mtr from MS Angle 65x65x6 mm/50x50x6 mm. The work includes cutting holes and providing MS Bolts of 16x40 mm size in the middle of the cross bracing with 1 No. sparing washer of proper size.

8.5 Mtr long PCC Pole

Grouting of support in CC 1:4:8(cement, sand & 40 mm. brick ballast) Grouting will be done in the block of size 45x45cmx1/6th of full length of the support upto ground level, 30 cm plinth above the ground level with CC 1:3:6 (cement, course sand and stone grit) with muffing. The work includes back filling and proper ramming etc. a) Single support

8.5 Mtr long PCC Pole

b) Double pole structure

8.5 Mtr long PCC Pole

Grouting of Stay Rods(20x1800)mm including all work of excavation, cement concrete in size of (0.60x0.60x0.30)M in the ratio of 1:4:8(cement, sand, 40mm brick ballast) including back filling of soil and proper ramming etc.

Fixing, tightening and nozelling of stay wire with stay rod with the pole of required tension by providing stay clamps.

Earthing of support with MS Earth Rod of (20x2500)mm long including excavation of pit and driving MS Rod 3.0 M apart from support and 0.5 M below the ground level and connecting below the earth electrodes with the help of GI wire No. 8SWG and earthing lugs

Replacement/fixing of 11 KV Pin Insulator with Pin

Laying ,stringing and binding of ACSR Weasal Conductor as per RESPO Norms and as per direction of Supervising Engineer.

Dismentling of G I wire and ACSR weasal Conductor of existing 11 KV Line

Spreading ,stringing and binding of AB Cable 3x50+1x35+1x16 as per RESPO Norms and as per direction of Supervising Engineer.

Cartage and Installing of Distribution LT Box with fitting by providing of bolt and nuts as per RESPO Norms and as per direction of Supervising Engineer.

Providing F Brakets with nut and bolts

Providing nuts and bolts with clamp

Providing Barbed wire

Providing and fixing Stone pad

Providing and fixing suspension clamp with nuts

Providing Holding clamps for X-Arm

Providing and fixing Danger board with barbed wire including jumper

M/s I K ELECTRICAL