SPECIAL REPAIR TO GOVT MD ACCN BLOCK NO P-42 (QTR 1 TO 6) AT SNOW VIEW LINE AT PALAMPUR MIL STN

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified.

Taking down chowkhats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) all as specified & directed.

Taking down chowkhats or frames exc 1.50 sqm but n.exc 4.00 sqm with shutters (without taking off shutters from the frames) all as specified & directed.

Taking down shutters of any description exc. 1 Sqm but not exc. 2 Sqm each, all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

75 mm thick plain cement concrete M-7.5 (Nominal mix), type D-2 (using 40mm graded brick aggregate) as in foundations/ sub base or in mass filling all as specified and directed.

Plain cement concrete M-15 nominal mix, type B-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains all as specified.

Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters (two panels) with lock rail and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides. The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, all as specified.

Factory made 2nd class soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pined at joint complete all as specified .

Factory made 35mm thick second class hard wood (Sal) glazed and skelton door shutters open rebated and prepared to receive glass gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers with edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass or gauge etc., as in windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b) of part-I, fitted to chowkats, complete all as specified.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each including preparation of articles and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II

Aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 300 mm long, all as specified and directed.

Mild Steel cold rolled medium weught butt hinges 100 mm, complete all as specified.

Continuous (piano) hinges, mild steel, bright finish or electro galvanised width of flap 30mm, complete all as specified.

Extruded aluminum alloy handle, fabricated type anodised of size 150 mm complete all as specified and directed.

Aluminium anodised, barrel tower bolts of size 150mm extruded section and fixed all as specified & directed.

Mild steel, 300mm, ordinary rat tail, rod pattern springs including roller and roller plate complete fixed to chowkhats, all as specified.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks of galvanised wire staple fixed with stainless steel wire staples all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry as in flooring and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding and polishing complete laid over and including 15 mm thick screed bed in cement mortor (1:6) (1 cement : 6 coarse sand) laid and jointed with gray cement slurry mixed with pigment, complete all specified.

Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 20mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC subbase complete, all as specified. Note:- PCC sub base if provided, shall be measured and paid under respective Items of BOQ.

Machine cut kota stone slab 15-20 mm thick as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab as in in skirting, dados, risers to steps etc, laid over and including 10 mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Mat finish, premium quality, non skid, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic, premium quality, coloured/ printed tiles 300mm x 200mm X 7 to 8 mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed.

25mm thick cement concrete M-15 (Nominal mix) type B-0 (using 12.5mm graded crushed stone agg ) as in flooring, finished even & fair complete all as specified and directed.

Coloured chequered cement concrete tiles machine pressed of size 25cmx 25cmx 25mm thick with grey cement, set jointed & pointed in neat cement slurry mixed with pigment to match the shade of the slab in floors laid over and including 15mm thick screed bed in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Rendering cement plaster 15 mm thick on fair faces of brick/ concrete surface in cement mortar 1:6 (1 cement : 6 coarse sand) and finished even and smooth without using extra cement complete all as specified.

Rendering cement plaster 10 mm thick on fair faces of brick/ concrete surface in cement mortar 1:4 (1 cement : 4 coarse sand) and finished even and smooth without using extra cement complete all as specified.

Rendering cement plaster 15 mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer), on other than fair faces of brick wall or on stone masonry surfaces, trowelled to even and smooth finish without using extra cement complete all as specified.

4mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden beads in square pane not exc 0.50 Sqm each pane in wooden/ Steel windows complete all as specified and directed.

Prepration of old plasters / unplasterd ceiling surface including brooming down or steel wire brushing, scarping down smoke soot, moulds, moss and effloresent salts and trading oil and greasy spots etc and applying one coat of white washing , complete all as specified and directed.

Prepration of old plasters / unplasterd ceiling surface including brooming down or steel wire brushing, scarping down smoke soot, moulds, moss and effloresent salts and trading oil and greasy spots etc and applying one coat of distemper oil emulsion , complete all as specified and directed.

Prepration of old wall surface by removing existing treatment by scarping, brushing etc including making surface clean , dry and free from any loose paint film, dirt, chalk, grease, fungus and algae and filling holes, dents, cracks with mixture of white cement and mortar for applying two coats of acrylic , antifungal plastic emulsion exterior weather proof paint upto 15 mt height , complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Painting two coats with synthetic enamelled paint on new steel or iron surfaces of any description exceeding 10cm width/ girth including preparation of surfaces over a coat of red oxide primer all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Mild steel work as in hold fast or similar small articles fabricated out of flat iron 25mm X 3 mm conforming to grade Fe-290 grade E-165, all as specified.

PCC M-15, nominal mix, type B-1, using 20mm graded mechanically crushed stone aggregate as in hold fasts / bed blocks / coping etc, all as specified.

4 mm thick Figured glass, pin headed type, 3mm thick and glazing with oil putty in squares not exc. 0.5 Sqm in each pane, complete all as specified.

Hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws of size 75 mm, all as specified.

Taking down water tank exc 250 ltr but not exc 500 ltr capacity and removing to store, complete all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including taking down of old tank, all as specified.

Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule for bore of pipe 20mm, complete all as specified.

Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests,( excluding flushing cistern and flushing pipe) white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, complete all as specified.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long including PVC connection 15mm dia 450mm long with brass CP nuts and washers at both ends, complete all as specified.

Wash hand basins, Vitreous China (oval type, coloured) size 550mmx400mm, excluding tap etc including brackets with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, PVC connections 15mm size with CP brass coupling nuts of length 450mm, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, chain and plug, PVC 32mm dia flush pipe and all accessories fixed in repair complete as all specified and directed. Make: Cat Part No. 1008 of Cera or equivalent makes mentioned in Appx 'C'

PVC waste water pipe 32 mm or 40 mm dia 750 mm long for wash hand basin / sink , complete all as specified.

PVC (SWR) pipes, 75mm dia, single socketed, in any length with rubber ring joints, fixed to walls in repair, complete all as specified & directed.

PVC (SWR) pipes, 75mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors as in repair, complete all as specified & directed.

75 mm bore PVC (SWR) junction single (Single T ) equal or unequal, complete all as specified.

PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, fixed in repair dia of outlet 75mm, complete all as specified.

75 mm bore PVC (SWR) bends any radius, complete all as specified.

110 mm bore PVC (SWR) junction single (Single T ) equal or unequal, complete all as specified.

PVC (SWR) pipes, 110 mm dia, single socketed, in any length with rubber ring joints, fixed to wall , celling, floors etc (fixed in repair) , complete all as specified & directed.

110 mm bore PVC (SWR) bends any radius( fixed in repair) , complete all as specified.

PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, fixed in repair dia of outlet 110 mm, complete all as specified.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered `Hot’ or `Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm dia, complete all as specified.

Bib cock CP for 15 mm bore fancy type , cast copper alloy, screwed down scrwed for iron pipe or brass ferrule and fixed in repairs, complete all as specified.

Stop cock CP for 15 mm bore fancy type , cast copper alloy, screwed down high pressure scrwed both ends for iron pipe or for unions and fixed in repairs, complete all as specified.

PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified.

Waste coupling 32 mm or 40 mm Cpfor glazed ware sinks, basins, etc each with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, complete all as specified.

Cast iron floor trap with CI grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), dia of outlet 75mm, complete all as specified.

Soap dish, brass chromium plated any type fixed to plugs with chromium plated brass screw, complete all as specified and directed.

Towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and and wooden/plastic cleats (minimum weight 170 gms) fixed on walls, complete all as specified.

Taking up or down steel tubing 15mm dia and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20mm dia and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Mild steel galvanised iron tubings (ISI Marked) 15mm dia medium grade with all fittings & fixtures complete to walls/ ceilings or laid in floors all as specified and directed.

All as per item no 72 above above but except GI tubing , complete all as specified.

Mild steel galvanised iron tubings (ISI Marked) 20mm dia medium grade with all fittings & fixtures complete to walls/ ceilings or laid in floors all as specified and directed.

All as per item no 74 above but except GI tubing , complete all as specified.

Drapery rails, mild steel, chromium plated with fixing brackets, stop roller etc , complete all as specified.

Stainless steel sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union etc. and overall size 915x460mm with bowl size 410x330x160mm, complete all as specified & directed.

Aluminium anodised powder coated frame for door s, windows with one or more rebates including joining cleat for fixing etc, complete all as specified & directed.

Aluminium anodised powder coated double sliding shutter windows and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/mt including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc, complete all as specified & directed.

5.5 mm thick tinted glass, complete all as specified & directed.

Mild steel square bar for framed work such as grills with ends of bar shouldered and riveted, or forged into spikes, framed guard bars conforming to Fe-290 gde E-165, complete all as specified & directed.

Demolition of existing concrete/ PCC tiles on roof slab. Taking down cement plaster including existing tarfelt from roof , of old roof surfaces by brushing with wire brushes from removing caked etc sweeping with brooms and finally fanning the cleaned surface to remove all loose dit etc on roof and applying the followings:- FIRST COURSE- One coat of bitumen primer conforming to IS- 3384@ 0.40 kg/sqm SECOND COURSE- One coat of bonding material using blown type bitumen conforming to IS- 702 grade 85/25 @ 1.20 kg/sqm THIRD COURSE- A layer of APP modified polymeric membrane, centre core of 100 mm micron HMHDPE, outer film 20 micron each, thickness 3 mm , having weight 2.25 kg/sqm , complete all as specified & directed. FORTH COURSE- One coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 2 1.20 kg/sqm.

Cement Concrete (1:2:4) type B1 using 20 mm graded aggregate as in roof kerbs, mud stoppers rounded or chamfered on edegs, padding concrete etc and cutting grooves 10mm wide and 25 mm deep filled with bitumen of grade 85/25 , complete all as specified & directed.

Taking down cement plaster from roof edegs of any description , complete all as specified & directed.

Taking down cement plaster from roof edegs of any description , complete all as specified & directed.

Taking down carefully unservicable Aluminium / Copper point wiring complete ( light , fan , socket, bell or power) with fitting such as switches, ceiling rose lamp holder regulators sockets, light fittings etc and keeping in safe custody for credit . And making good disturbed surface of wall, floor etc , complete all as specified & directed.

Taking down carefully unservicable sub main wiring of any size including batten conduit earth wire etc And making good disturbed surface to match the existing surface , complete all as specified & directed.

Taking down carefully unservicable TPN DB with MCBs of any make/ capacity , complete all as specified & directed.

Taking down carefully unservicable MCB DB with MCBs of any make/ capacity , complete all as specified & directed.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC casing and caping of approved size, medium grade, ISI marked with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly and including pressed steel terminal boxes made out of 1.20 mm thick mild steel sheet duly painted with one coat of red oxide primer for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point or one bell point, controlled by one way switch/ push button complete including making good disturbed surfaces to match with existing all as specified and directed.

All as per srl item no 90 above but for one fan point / exhaust fan controlled by one one way switch and regulator complete all as specified.

All as per srl item no 90 above but for one bell point controlled by one one way bell push complete all as specified.

All as per srl item no 90 above but for 3 pin socket outlet 5 amp independent board complete all as specified.

All as per srl item no 90 above but for 3 pin socket outlet 5 amp same board complete all as specified.

All as per srl item no 90 above but for one light point controlled by two way switches complete all as specified.

All as per srl item no 90 above but for 3 pin socket outlet 15 amp independent board with cable of size 2.5 sqmmin point wiring and 1.5 sqmm in continious earth wire complete all as specified.

Switch piano flush type, single pole, one way, 6 Amps, all as specified.

Switch piano flush type, single pole, two way, 6 Amps, all as specified.

Switch socket outlet 3 pin, 5 amps flush type, all as specified.

Switch piano flush type, single pole, one way, 15 Amps, all as specified.

Switch socket combination two in one, 3 Pin 5 amps and 15 amps, flush type, all as specified.

Bell push piano flush type single phase one way 5 amp 240 volts for electric bell complete all as specified.

Musical door bell 230 volts AC single phase complete all as specified.

Flush type, step fan speed controller suitable for 1200/ 1400 mm sweep ceiling fan complete all as specified and directed.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 4 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 4 Sqmm, shall be measured as one RM).

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 12 way, double door, 240 volts with 200 Amp rated bus bar, all as specified. Make : Havells Cat Part No. DHDPSHODPW12 or equivalent in makes mentioned in Appx 'C'.

MCB TPN 63 amp 230 volts "C" series complete all as specified.

MCB SPN 40 amp 10 KA 230 volts "C" series complete all as specified.

MCB SP 40 amp 10 KA 230 volts "C" series complete all as specified.

MCB SP 6 to 32 amp 10 KA 230 volts "C" series complete all as specified.

Blanking plate for MCB complete all as specified.

LED tube light fitting box type sutable for 1X20W 4FT complete with led tube rod fixed complete to wall / ceiling and PVC round / square block (02nos) of suitable size etc provied complete including from ceiling rose to connector with flexible pipe of suitable size of all complete all as specified. Make- crompton cat part no DMLN1LT8 16 with tube cat part No. LT8-20-865-2 or equivalent in makes mentioned in Appx 'C'.

Integral steek extruded polycarbonate LED channel 5 watt 1FT complete with white acrylic cover batton integrated connection from ceiling rose connector complete all as specified. Make- Bajaj cat part No. 112406BCLSB 05 NW or equivalent in makes mentioned in Appx 'C'.

Batten holder with 10 watt LED complete all as specified.

Pressure die cast housing with epoxy power coated dark graphite grey colour finish prismatic polycarbonate cover with individual LED lenses with 30 watt LEDs as light source complete all as specified. Make- Polycab cat part No PUB0501037 or equivalent in makes mentioned in Appx 'C'.

Street light bracket made out of 32 mm dia GI light grade tubing not less than 1.5 mtr long bend to shape including pole clamps made out of 50 mm X 6 mm iron strip and nut bolts and washers complete all as specified.

Taking down old unserviceable light fittings / bulkhead fittings of any type and model complete and making good the disturbed surface complete all as specified.

Distribution board iron clad DB double door with IP-43 protection 415 volts 3 phase 50 Hz 4 way complete with appropriate size of copper busbar and neutral link complete and including cutting chasing to wall for fixing DB and making good disturbed wall to match with existing surface complete all as specified. Make- Indo Asian cat part No. 811840 or equivalent in makes mentioned in Appx 'C'.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick cover of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Disconnecting / Takingdown and refixing in sevicible condition of electric water heater any type / any capacity removing and cleaning the dust properly, painting with same colour good quality synthethic enemelled paint after preparing surface for painting including refixing and making the conection and testing complete all as specified.

Disconnecting / Takingdown exhaust fan of any size / any type removing and cleaning the dust properly, painting with same colour good quality synthethic enemelled paint after preparing surface for painting oiling and greasing of bearing including refixing and making the conection and testing complete all as specified.

Disconnecting / Takingdown ceiling fan of size 1200 mm / 1400 mm sweep removing and cleaning the dust properly, painting with same colour good quality synthethic enemelled paint after preparing surface for painting oiling and greasing of bearing including refixing and making the conection and testing complete all as specified.

BHARDWAJ BUILDERS