Construction of Chief Office Building of JSV Department Dharamshala in Tehsil Dharamshala Distt. Kangra H.P

Amount

Providing detailed architectural drawings including 3-d view & structural design with 6 No. sets of working drawings based on relevant code of practice of buildings in India for construction of proposed conference hall in consultation with Engineer-in-Charge. The contruction shall engage an architect & civil/ structural Engineer with consultation if Engineer-in-Charge (Executive Engineer) I&P.H Division D/Shala. The structural design/ drawing will have to be velted as proof check from Govt. Institution before submission to H.P I&P.H Deptt. Any change required in structural design during construction stage as per site requirement will have to be done by contractor/ consultant without any extra cost. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Excavation in foundation trenches etc.( for pipes and pits)up to all depths in all kind of soil such , as pick work, jumper work saturated soil including bailing or pumping out water, blasting soft/hard rock or chiselling soft /hard rock where blasting is prohibited in all leads & lifts including triming & dressing of sides levelling of beds to correct grade including shorting struttering planking timbering and dewatering where ever required stacking usable/unusable material / soil separately and after laying jointing and testing of pipes returning the usable soil in trenches in 15cm layers including consolidating of such deposited layer by ramming & watering & then disposing of all surplus excavated earth as directed with in all leads & lifts including restoration of unmetalled surfaces to its original condition & including cost of a diversion for traffic night signals,fixing caution boards crossing over trenches for access to houses fencing etc. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Excavation in drains channels etc in earth work including dressing of side and level earth upto a lead 20 mtrs and lift upto 1.50 mtrs disposed earth to be levelled and neatly dressed in pick and jumper work.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying cement concrete 1:4:8(1:cement :4 sand:8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in:-Foundation and plinth i/c carriage of material Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying cement concrete work 1:1.5:3(1cement:1.5sand:3graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:- Foundations, footings, bases of columns and the like and mass concrete. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Column, pillars, posts and struts upto floor two level

Stair cases etc.

Providing and laying cement concrete work 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:- (a) Suspended floor roofslanding & shelves & their supports balconies, beams, bressumers & cantilevers upto floor two level.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying cement concrete work 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in foundation and plinth. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing mild/tor steel reinforcement for RCC work i/c bending binding and placing in position complete up to all floor level Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing form work with steel plates 3.15 mm thick welded with angles iron in frame 30 x 30 x 5 mm so as to give a fair finish including centering shuttering struting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor two ceiling not exceeding 4 meters and removal of the same for in-situ- reinforced concrete and plain concrete in: Vertical surface such as wall (any thickness) partition and the like i/c attached pillasters, butresses plinth and string course Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

In Column, pillars, posts and struts : Square, rectangular or polygonal in plan.

In Sides & soffils of beams, beam haunchings. Cantilevers, bressumers and lintels not exceeding 1mtr. In depth inall heights from floor

In flat Surfaces such as soffits of suspended floor, roofs, landings etc.

Edges of slab and breaks in floors and walls under 20 cm wide. complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Brick work using common burunt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1 cement : 6 sand) (Ist class brick)Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

6mm cement plaster to ceiling in CM 1:3 ( 1 Cement : 3 Sand) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:5 (1 cement: 5 sand) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

20 mm thick cement plaster in single coaton rough side / of brick/ stone mansonary for interior plastering upto floor two level including arrieson, internal rounding angles, chamfers etc. and smooth with cement mortor 1:6 Sand ( 1 cement :6 sand ) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Stone soling under floor Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying vetrified double charge tiles 600x1200x10mm in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortor 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry flush pointing in white cement mixed with pigment of required shade to match the shade of tiles Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Coloured glazed tiles 6 mm thick (300x450 mm) in skirting risers of steps and dedo12 mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with cement slurry Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortor 1:3 (1cement : 3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete. 20 mm thick Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Kota slab 55 mm thick in risers of steps, skirting dado and pillars laid on 12mm (average) cement mortar 1:3 and jointed with gray cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing 8 mm th. Laminated wooden tuscon ( vitro floor) made in Germay high pressure laminate panels fixed on wall and floor with all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providng and fixing wooden wall panel size 2440*133*16 mm fixing with aluminium centre clips including aluminium edges with aluminium edges with aluminium keels Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

HPL Ceilling :- Providing and fixing of HPL (High Pressure Laminates) of branded company front ACE terminate and water proof material and 6 mm thick putting on Galvanised Gypsum section heavy weight fram structure with all accessoriesComplete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868 (Minimum anodic coating of grade AC 15) fixed with rawplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rustfree , straight, mitred and jointed mechanicaliy where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P brass/stainiess steel screws. For doors, windows and ventilatiors and glazed partitions frames (Powder coated coioured aluminium frame No. 2443x137x137x4510x1.755mm of Jindal make aluminium).Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providng and fixing shutters for windows and ventilators consisting of Al. style No. 453 47.62*44.45*3.00mm for style of Jindal Al. extrusion or equivalent i/c full panel of A.C.P with Al. channel No. 3055 for rebate of Al. Jindal Al. extrusion complete as per approved drwing and design. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providng and fixing shutters for windows and ventilators consisting of Al. style No. 453 47.62*44.45*3.00mm for style of Jindal Al. extrusion or equivalent i/c full panel of 4mm thick glass with aluminium channel No. 3055 for rebate of Al. Jindal Al. extrusion Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providng and fixing shutters for windows and ventilators consisting of Al. style No. 453 47.62*44.45*3.00mm for style of Jindal Al. extrusion or equivalent i/c full panel of wire guage with aluminium channel No. 3055 for rebate of Al. Jindal Al. extrusion complete as per approved drawing and design. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Wall painting (one coats) with plastic emulsion paint of approved brand and manufacturer on undecorated wall surfaces to give an even shade i/c throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Extra over item No. 1718100 for painting with plastic emulsuon paint of approved brand and manufacturer on undecorated wall surfaces to give an even shade i/c throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth i/c applying of putty for making the surface.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Painting with apex Excel paint (two coats) excluding coat superior done finish harmoney on undecorated wall surfaces to give an even shade after throughly cleaning the surface i/c water proof treatment.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing Aluminium grill Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & fixing 250 x 16mm anodized aluminium sliding door bolts bright finished black enamelled with nuts and bolts smooth Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & fixing bright finished aluminum Tower bolts (barrel type) with screws 250x10mm etc. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & fixing Aluminium finished handles with necessary screws complete 125mm. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & fixing Aluminium finished Door closer with necessary screws complete 100mm. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & fixing Stainess steel railing Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & laying in trenches galvanised mild steel tubes (Light grade) tube fitting (Earth work in trenches to be measured and paid for seperately .25mm dia . Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing GI Union 25mm of following dia ISI marked Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing GI Socket 25mm of following dia ISI marked Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing GI Elbow 25mm of following dia ISI marked Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing GI Nipple 6" Long 25mm of following dia ISI marked Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing GI Tee 25mm of following dia ISI marked Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and Fixing viterious china padestral for wash basin complete recessed at the basic for reception of pipe and fittings Cera sanitary work (carnet) white (Viterious China in White Colour) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing Vitreous china Wash, down water closet (European type W.C pan) with integral "P" or "S" inccluding jointing the trap with soil pipe in cement mortar 1:1 (1cement :sand)seat cover to be measured and paid for sperately---Anglo Indian (Universal Closet) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing Vitreous china Wash, down water closet ( Anglo Indian) with integral Por S trap i/c jointing the trap with soil pipe in C.M 1:1 PVC Cistern etc. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing urinal pot Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P Pillar cock 15 mm dia i/c all accessories. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providng and fixing C.P long body tap i/c all accessories. (Superior & heavyone not less than 300 gms.) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P Short body tap i/c all accessories. (Superior & heavyone not less than 300 gms.)Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P angle valve 15 mm dia without nuts and pipe (Superior & heavyone) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P concealed of heavy class & superior one i/c all process of fixing with existing system,Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P Union connection pipe with 15mm dia i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing PVC floor trap 100m dia of Finolex/ Diplast mak i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing PVC S- trap 100mm dia of Finolex/ Diplast make i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P grating 100mm dia i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing PVC Pipe 100mm dia of Finolex/ Diplast mak i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing PVC Pipe 75mm dia of Finolex/ Diplast mak i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying PVC Bend of Finolex/ Diplast make100mm dia i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying PVC Door Bend of Finolex/ Diplast make100mm dia i/c all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

75 mm dia

Providing and fixing PVC Socket of Finolex/ Diplast make100 mm dia Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

75 mm dia

Providing and fixing 600x450mm bevelled edge mirror of superior glass and ornamental type, mounted on 6mm thick AC sheet or plywood sheet and fixed to wooden plugs with CP brass screws & washers. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P soap tray complete with C.P Brackets fixed to wooden plugs with C.P brass screws. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing PVC Corner complete fixed to wooden plugs with C.P brass screws. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing PVC waste pipe for wash basin or sing i/c all accessories. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing C.P soap Dish complete with C.P Brackets fixed to wooden plugs with C.P brass screws. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing Steel work welded in built up sections trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paint in gratings, framed, Guard bars,ladders, railing and (similar work) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing &fixing of Zebra Blinds of SSG BLINDS with powder coated channel & cap Dori set, brackets with imported Fabric including installation Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. ( Group C ) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit, with 2-way modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. ( Group C) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

2x1.5 Sq. mm.

2x2.5 Sq. mm.

2x4.0 Sq. mm.

2x6.0 Sq. mm.

2x10 Sq. mm.

2x16 Sq. mm.

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and drawing LAN cable CAT 5E, solid copper conductor protected with PVC sheath in the existing surface / recessed, steel / PVC conduit 2 Pair Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required:- Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

20 mm. dia

25 mm. dia

32 mm. dia

40 mm. dia

50 mm. dia

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

2 modules (78mmx78mmx50mm)

4 modules(140mmx78mmx50mm)

6 modules(205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

12 modules (205mmx135mmx60mm)

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

S.P. 5/ 6 Amps one way Modular switch.

S.P. 5/ 6 Amps two way Modular switch.

Bell push, Modular.

S.P. 15/ 16 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

6 pin,15/16 Amps Modular socket outlet.

Telephone socket outlet, Modular.

TV. Socket outlet, modular.

Supplying & fixing following size modular base and cover plate on the existing modular metal boxes as required:-Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Modular base and cover plate, 2 module

Modular base and cover plate, 4 module

Modular base and cover plate, 6 module

Modular base and cover plate, 8 module

Modular base and cover plate, 12 module

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing metal box of 100mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps, piano type switch, connections, painting etc. as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps, piano type switch, connections, painting etc. as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps, piano type switch, connections, painting etc. as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required:- Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and erection of following depth sheet metal cubical pedestal of suitable dimensions with plus-minus 5 cm variation, made from 1.6 mm thick M.S. sheet duly fabricated in a segregated manner for housing of switch fuse units, by welding each compartment on five sides & front side hinged, complete with locking arrangement, with sufficient No. vertical and horizontal intermediate switchgear housing compartments. The cubical pedestal shall have cable entry box at one or two sides, with epoxy powder coated approved paint and bonding to the existing earth etc. The same shall be erected in the 1:2:4 cement concrete plat-form of suitable dimensions 15 cm high from ground level and 45 cm thick. The cubical pedestal shall be 15 cm from the top of cement concrete plat-form:-600 mm deep (nominal)Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing sheet metal bus-bar chamber suitable for 800 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 2000mm & cross-sectional area (50.80mmx9.50mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (2080mmx700mmx380mm) nominal with all accessories including connections, earthing the body etc. as required:-Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing copper strip bus-bars suitable for 63 Amp. 415 volts capacity 4 No. each of cross-sectional area (16mmx3.17mm),in the existing enclosure with all accessories including connections etc. as required:-Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing following rating double pole switch disconnector fuse unit cubical type, 415/500 volts, with 2 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

32 Amp. Category-A

63 Amp. Category-A

Providing and fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required.as per direction of Engineer-in-Charge with in all leads and lifts.

32 Amp. Category-A

63 Amp. Category-A

Providing and fixing following rating, three pole, manually operated, draw-out type, air circuit breaker, microprocessor based release;SR18G, open execution, in the cubicle panel, making connections, etc. as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

630/800 Amp. -50 KA; C-Power

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:-Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Single pole. Cat-A.

Single pole & neutral. Cat-A.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amps. Cat-A.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. Double door-16 way as required:-Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing 25mm x 5mm copper strip in 40 mm dia. G.I. pipe from earth electrode etc. as required.Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the required size:-as Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Armoured cable 16 sq. mm (four core)

Armoured cable 25 sq. mm (3.5 core)

Providing and laying of aluminium conductor, PVC insulated and PVC sheathed, unarmoured/XLPE power cable, working voltage 1100 volts grade direct in ground in the same trench, in one tier horizontal formation to be laid 1 meter below the ground level including excavation and refilling the trench etc.as required, but excluding sand cushioning and protective covering etc. of required size:-Unarmoured cable 10 sq. mm (twin core) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required:- 10 Liter capacity water heater (Cat-A) ( Havell/ Bajaj make ) as per direction of Engineer-in-Charge with in all leads and lifts.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. Ceiling Fan 1400 mm sweep, Category-A ( Havell/ Bajaj make ) as required:- Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:- Exhaust Fan, Heavy duty, 100 mm sweep ( Havell/ Bajaj make ) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing shock proof slim decorative extruded fixture with domestic electronic ballast, suitable for 36 watt FTL (T8), complete with all accessories (excluding the T-8 Tube), connections, testing and commissioning etc. as required.1 x36 watt-FTL(T8) (Category-A) Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing trim clip on LED Panel 24 W 3000 k Unique recess cum surface panel with no additional attachemnt needed for surface installation ultra slim surface design at 14 mm variable cutout size with minimum 60 mm cut out i/c testing and commissioning etc. as required. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing and fixing trim clip on Square LED Panel 24 W 3000 k Unique recess cum surface panel with no additional attachemnt needed for surface installation ultra slim surface design at 14 mm variable cutout size with minimum 60 mm cut out i/c testing and commissioning etc. as required. Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & fixing Air conditioner 1.50 Tonne with inbuilt Air purifier ( AL Dual invertor) , WiFi Split A.C ( Copper ) Super convertible Six in One Cooling P.M 1.0 Sensor & Display , four way swingMakes :- L.G / Havells /Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Providing & fixing water purifier with complete accessories of LG/ Eureka forbes make i/c Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

Prov & fixing Ceasefire ABC Powder MAP90 fire extinguisher ( 4 Kg) of approved make with all accessories Complete in all respect i/c all leads and lifts. as per the direction and satisfection of the Engineer-in-Charge

RAKESH RANA

Ujjawal Singh