Loading
Loading…
Loading…
Tender Value
₹2.3 Cr
EMD Value
₹4.6 L
Closing Date
2 Sept 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
MAINTENANC
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V = Advertised value of the tender in crores of Rupees N = Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer shall possess a valid Electrical Contractor License, issued by any State Government or Union Territory Administration, authorizing execution of electrical works up to 650 V. The contractor shall have in his employment or shall engage a person holding a valid certificate of competency issued by any State Government or Union Territory Administration for supervision of electrical works up to 650 V. Offers not accompanied by a valid Electrical Contractor License and requisite Supervisor competency for works up to 650 V shall be summarily rejected.
Similar Nature of Work: Supply, installation, testing and commissioning (with or without supply) of motor driven pump of any type or capacity in railways/airport/Defence/CPWD/PWD/Govt PSU/Govt department.
49 conditions · 8 needing a document upload
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society /Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. and corresponding documents shall be submitted by the tenderer as per the composition of the Firm.
The Bid Security shall be deposited either in cash through e payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India or as mentioned in tender documents. The Bank Guarantee bond shall be as per Annexure- VIA of GCC and shall be valid for a period of 90 days beyond the bid validity period. Non-submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non- submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document within 5 working days of deadline of submission of bids.
Eligibility criteria :- Eligibility criteria shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document.
Tender Form (First sheet, Second sheet) of The GCC April 2022.
Certificate format (Affidavit) which available as Annexure - V in Mandatory documents. A facility has already created for online submission of Annexure V of GCC in IREPS module, uploading of physically signed Annexure V by tenderer has been discontinued.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society /Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.
The corresponding documents shall be submitted by the tenderer as per the composition of the Firm: Sole Proprietorship Firm: (i) All documents in terms of Para 10 of the Tender Form (Second Sheet) above. HUF: (i) A copy of a notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above. Partnership Firm: (i) All documents as mentioned in para18 of the Tender Form (Second Sheet). Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) above. LLP (Limited Liability Partnership): (i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet). Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents andcreate liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.
The tenderer shall be required to submit the Bid Security with the tender for the due performance with the stipulation to keep the offer open till such date as per Clause No.5 of PART -1 of The GCC, April 2022.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
GTL Div: Provision of Star Rated Energy Efficient Pumps in Place of Old and Over Aged Conventional Pumps at AD, DMM, DHNE, GY, HX, NRE, PAK, RC and RU Sections
GTL-EM-28-2026-27~SCOR
GTL-EM-28-2026-27
Open
Works - General
6 Months
Anantapur, Andhra Pradesh
₹0
₹4.6 L
10 Aug 2026
10 Aug 2026
19 Aug 2026
61 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 2,31,76,069.54 | ||
| — | Item Breakup | for details. | — | ||
| Supply Installation, testing and commissioning of ISI marked 5.0 HP vertical submersible pump set, 15 stages,Vertical submersible pump set,Three Phase, 415 Volts, copper winding, Stainless Steel PumpShell, Stainless Steel MotorBody & Shaft, suitable for 150mm dia bore well pump set,Pump size : 50 mm, Head: 124Mtr , LPM 60, similar to TAROpump Model TRS 3015 RF + TS037 R or its equivalent | — | — | — | 34,90,308.36 | |
| — | Item Breakup | for details. | — | ||
| S u p p l y Installation, testing and commissioning of ISI marked 1.0 HP, 18 stages,Vertical submersible pump set,Single phase, 220/240 Volts,copper winding, Built-in NRV,Stainless Steel Pump Shell,Stainless Steel Motor Body &Shaft, suitable for 100 mm dia(4") bore well, Pump size: 30mm, Head: 104 Mtrs, LPM: 13,similar to TARO pump Model TRF418 HS + SF 007 or itsequivalent | — | — | — | 13,68,997.2 | |
| — | Item Breakup | for details. | — | ||
| S u p p l y Installation, testing and commissioning of ISI Marked 3.0 HP, 18 stages,Vertical submersible pump set,Single phase, 220/240 Volts,copper winding, Built-in NRV,Stainless Steel Pump Shell,Stainless Steel Motor Body &Shaft, suitable for 100 mm dia(4") bore well, Pump size: 32mm, Head: 28-259 Mtrs, LPM: 0-66 ,similar to Kirloskar pump Model KS4BN - 3035 or itsequivalent | — | — | — | 35,636 | |
| — | Item Breakup | for details. | — | ||
| Supply, installation, testing and commissing of ISI marked 15 HP MONO BLOCK PUMP SET of Model No.KDS 1555+ of Suction Size : 80mm and Delivery Size : 65 mm, 3ph motor, 415 V, 50 HZ, with discharge of 19.9-12.2 LPS & head of 22m-52m with all necessary connections and all other accessories | — | — | — | 3,50,460 | |
| — | Item Breakup | for details. | — | ||
| Supply Installation, testing and commissioning of of ISI marked 10.0 HP Horizontal open well fountainsubmersible pump set, ThreePhase, 415 Volts, AC Supply, 50Hz, copper winding, in operatingin a wide voltage dynamicallybalanced rotor and impellerensure vibration freeperformance and enhanced life,Pump size: 65 x 65 mm, Head:50 Mtrs, LPM: 804, similar toTARO pump Model TSM 14 HF orits equivalent Note: Head /Discharge depending upon sitecondition to be ascertainedbefore supply of Pump" | — | — | — | 7,37,762.76 | |
| — | Item Breakup | for details. | — | ||
| S u p p l y Installation, testing and commissioning of ISI marked of 3.0 HP, 25 stages,Vertical submersible pump set,Three Phase, 415 Volts, copperwinding, Built-in NRV, StainlessSteel Pump Shell, StainlessSteel Motor Body & Shaft,suitable for 100 mm dia borewell pump set, Pump size : 40mm, Head: 115 Mtr , LPM :78,similar to TARO pump Model TRF1525 + TF 022 or its equivalentNote: Head / Dischargedepending upon site condition tobe ascertained before supply ofPump" | — | — | — | 2,51,981.1 | |
| — | Item Breakup | for details. | — | ||
| Supply , installation , testing and commissioning of ISI marked monoblock type, energy efficient EE4 3 HP pump, suitable to deliver water to 8-20 Mtr. head, at the rate of 4.5-13.4 LPS approx., 3ph motor, complete as per IS 9079:2002 with suction of 65mm and delivery of 50 mm with all connected accessories equivalent to model no: KDI-318 EE4 of kirloskar make | — | — | — | 1,08,060 | |
| — | Item Breakup | for details. | — | ||
| Supply , installation , testing and commissioning of ISI marked 7.5 HP, 18 stages,Vertical submersible pump set,Three Phase, 415 Volts, copperwinding, Stainless Steel PumpShell, Stainless Steel MotorBody & Shaft, suitable for 150mm dia bore well pump set,Pump size : 50 mm, Head: 151Mtr , LPM : 120, similar to TAROpump Model TRS 3518 R + TS056R or its equivalent Note:Head / Discharge dependingupon site condition to beascertained before supply ofPump" | — | — | — | 22,41,815.4 | |
| — | Item Breakup | for details. | — | ||
| Supply , installation , testing and commissioning of ISI marked monoblock type, energy efficient EE4 5 HP pump, suitable to deliver water to 20-36 Mtr. head, at the rate of 6-8.45 LPS approx., 3ph motor, complete as per IS 9079:2002 with all connected accessories equivalent to model no: KDI-538 EE4 of kirloskar make | — | — | — | 1,07,970 | |
| — | Item Breakup | for details. | — | ||
| Supply , installation , testing and commissioning of ISI marked monoblock type, energy efficient EE4 10HP pump, suitable to deliver water to 12-30 Mtr. head, at the rate of 31.5- 1 3 . 5 L P S approx., 3ph motor, complete as per IS 9079:2002 with all connected accessories equivalent to model no: KDI-1030 EE4 of kirloskar make | — | — | — | 5,91,250 | |
| — | Item Breakup | for details. | — | ||
| Supply , installation , testing and commissioning of ISI marked 10 HP energy efficient ,Vertical submersible pump set,Three Phase, 415 Volts, copperwinding, Stainless Steel PumpShell, Stainless Steel MotorBody & Shaft, suitable for 150mm dia bore well pump set,Pump size : 50 mm, Head: 1123-194Mtr , LPM : 20-300, similar to Kirloskar pump Model 60HHN-1016 or its equivalent Note:Head / Discharge dependingupon site condition to beascertained before supply ofPump" | — | — | — | 19,81,039.2 | |
| — | Item Breakup | for details. | — | ||
| Supply and Transportation of 15HP, Three phase open well ISI submersible motor pumpset confirms to IS 14220 : 1994 or latest , of model no:OWS15.2 of CG make or equavalent pump of Kirloskar / Crompton / Texmo / CRI / KSB/Lub with equavalent design parameters capable of delivering (2400-1250) LPM at (18-36) mtr head with integral non return valve to operate 3 phase,50 Hz,440V AC supply complete with all necessary accessories including adaptor where ever necessary complete( suction and delivey pipe size 100*100mm). | — | — | — | 3,24,600 | |
| — | Item Breakup | for details. | — | ||
| Supply, Fabrication and fixing and commissioning of pump panel suitable for 5 Hp pum p made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side louvres with weld mesh inside etc., complete consisting comprising of motor protection circut breaker, DOL starter, electronic timer, ammeter, voltmetre, pilot lamps and capacitor complete with Under Voltage Protection, Over Voltage Protection, Dry Run Protection (with adjustable current setting and adjustable reset time), Voltage Single phasing Protection including wiring and all other connected accessories | — | — | — | 10,20,700 | |
| — | Item Breakup | for details. | — | ||
| Supply, Fabrication and fixing and commissioning of wall/pole mounted 7.5 HP pump control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side louvres with weld mesh inside etc., complete consisting of DOL starter, single phase preventer with ON & OFF with dry run Protection ,pilot lamps, selector switch, Voltmeter, Ammeter with all internal wiring using copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. | — | — | — | 11,15,400 | |
| — | Item Breakup | for details. | — | ||
| Supply, Fabrication and fixing and commissioning of wall/pole mounted 7.5 HP pump control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side louvres with weld mesh inside etc., complete consisting of DOL starter, single phase preventer with ON & OFF with dry run Protection ,pilot lamps, selector switch, Voltmeter, Ammeter with all internal wiring using copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. | — | — | — | 3,60,540 | |
| — | Item Breakup | for details. | — | ||
| "Fabrication , transportation and supply of suitable size panel board for single phase submersible motor up to 1.5 HP consisting of relay, Contactor, starting and running capacitors, Voltmeter, Ammeter, indicator lamps, MCB , on/off switch including supply and fixing of DOL starter of complete.," | — | — | — | 2,89,129.5 | |
| — | Item Breakup | for details. | — | ||
| "Fabrication , transportation and supply of suitable size panel board for single phase submersible motor 2 to 3HP consisting of relay, Contactor, starting and running capacitors, Voltmeter, Ammeter, indicator lamps, MCB , on/off switch including supply and fixing of DOL starter of complete.,." | — | — | — | 8,566.8 | |
| — | Item Breakup | for details. | — | ||
| Supply, Fabrication and fixing and commissioning of wall/pole mounted 3 HP pump control panel board made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side louvres with weld mesh inside etc., complete consisting of DOL starter, single phase preventer with ON & OFF with dry run Protection ,pilot lamps, selector switch, Voltmeter, Ammeter with all internal wiring using copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. | — | — | — | 94,815 | |
| — | Item Breakup | for details. | — | ||
| Supply, Fabrication and fixing and commissioning of wall/pole mounted 10 HP pump control panel board made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side louvres with weld mesh inside etc., complete consisting of Automatic Star Delta Starter, single phase preventer with ON & OFF with dry run Protection, under voltage protection, over current protection, ,pilot lamps, selector switch, Voltmeter, Ammeter with all internal wiring using copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. | — | — | — | 18,63,550 | |
| — | Item Breakup | for details. | — | ||
| Supply, running and connecting of 3core 6sq.mm. 1100V submersible flat cable conforming to IS:694. | — | — | — | 2,34,000 | |
| — | Item Breakup | for details. | — | ||
| Supply and running of 3core 4sq.mm. 1100V submersible flat cable conforming to IS:694. | — | — | — | 26,400 | |
| — | Item Breakup | for details. | — | ||
| Supply and running of 3core 2.5sq.mm. 1100V submersible flat cable of make conforming to IS:694. | — | — | — | 52,000 | |
| — | Item Breakup | for details. | — | ||
| Supply and running of 3core 1.5sq.mm. 1100V submersible flat cable of make conforming to IS:694. | — | — | — | 1,01,000 | |
| — | Item Breakup | for details. | — | ||
| Supply and erection of 32 mm dia GI Pipe 'B' class with threaded at both ends up to 75mm length with coupling/flanges complete confirming to IS: 1239(Part-I)2004 | — | — | — | 12,07,040 | |
| — | Item Breakup | for details. | — | ||
| Supply and erection of 40 mm dia GI Pipe 'B' class with threaded at both ends up to 75mm length with coupling/flanges complete confirming to IS: 1239(Part-I)2004 | — | — | — | 1,95,328 | |
| — | Item Breakup | for details. | — | ||
| Supply and erection of 50mm dia GI Pipe 'B' class with threaded at both ends up to 75mm length with coupling/flanges complete confirming to IS: 1239(Part-I)2004. | — | — | — | 34,77,000 | |
| — | Item Breakup | for details. | — | ||
| Supply and erection of 65 mm dia GI Pipe (Medium ) 'B' class with threaded at both ends up to 75mm length with coupling/flanges complete confirming to IS: 1239(Part-I)2004 including Joints, bends couplings and all necessary accessories complete. | — | — | — | 3,60,000 | |
| — | Item Breakup | for details. | — | ||
| Supply and erection of 80mm dia GI Pipe 'B' class with threaded at both ends up to 75mm length with coupling/flanges complete confirming to IS: 1239(Part-I)2004 including Joints, bends couplings and all necessary accessories complete. | — | — | — | 47,200 | |
| — | Item Breakup | for details. | — | ||
| Supply and erection of 100mm dia GI Pipe (Medium ) 'B' class with threaded at both ends up to 75mm length with coupling/flanges complete, confirming to IS: 1239(Part-I) 2004, including Joints, bends, couplings, and all necessary accessories complete. | — | — | — | 3,54,475 | |
| — | Item Breakup | for details. | — | ||
| Lifting of Submersible Pumps from existing boreof various capacities up to 600 feet depth, including transportation of pumps from site to depot, including labour works like engagementof labourforce, Tripod arrangement, tools etc at Contractor'scost | — | — | — | 7,79,045.22 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
LocDetailsGTL-EM-28-2026-27.pdf
ATTACHMENT
NITIREPSWorks.pdf
ATTACHMENT
CEGE Technical Circular
ATTACHMENT
ListofLikelySuppliers.pdf
ATTACHMENT
CEGETechnicalCircular07-04-2022_compressed.pdf
ATTACHMENT
GCC_April-2022WithCorrectionSlips._compressed.pdf
ATTACHMENT
RITESInspection.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].