SPECIAL REPAIR BLDG NO T-07 (OLD CAMP BK) AT 217 TRANSIT CAMP UNDER AGE (I) R AND D MANALI

Amount

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and as directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engineer-in-Charge.

S&F mild steel in Joist, channel, angle, or tee sections, Hollow or round steel tubes, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated), Fe 410 -W (GdeE- 250) quality-A, complete all as specified and as directed by Engineer-in-Charge.

S & F mild steel Windows Chajja / wind ties for roof covering including screwing bolts, etc complete all as specified and as directed by Engineer-in-Charge.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed by Engineer-in-Charge.

Dismantling of wall/ceilng boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness including cover fillets, complete all as specified and as directed by Engineer-in-Charge.

S&F Pre- painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and incl 20mm thick screed bed or bedding layer of cement mortar 1:4, complete all as specified and as directed by Engineer-in-Charge.

S&F 12mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face; fixed in with screws to timber frame work as in wall paneling, complete all as specified and as directed by Engineer-in-Charge.

S&F 12mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face; fixed with screws to metal frame work as in ceiling, complete all as specified and as directed by Engineer-in-Charge.

M&L Plain fillets,square,rectangular or triangular in section, clean sawn, secured with nails or brads of size exc 3sq cm and n. exc 6 sq cm of second class softwood complete all as specified and as directed by Engineer-in-Charge.

M&L for second class hardwood timber framed and fixed, clean sawn in scantling, complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs 4.0mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc. 0.5sq.m in each pane including hacking out from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed by Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed by Engineer-in-Charge.

M&L for Pre-cast cement concrete block 1:3:6 type C1 (using 20mm graded aggregate) masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed by Engineer-in-Charge.

M&L rendering 15mm thick on brickwork or concrete surfaces or surface other than fair face of brickwork in CM (1:4) finished even & smooth (without using extra cement) complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint, white or tinted complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm and n. exc 4 Sqm each complete all as specified and as directed by Engineer-in-Charge.

S&F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 125 x 60mm complete all as specified and as directed by Engineer-in-Charge.

S&F flush shutters, 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides as per SSR Part-I, complete all as specified and as directed by Engineer-in-Charge.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed by Engineer-in-Charge.

S & F Extruded aluminium alloy handles, fabricated type, 150mm size complete all as specified and as directed by Engineer-in-Charge.

S & F Aluminium anodised, barrel tower bolts of extruded section and fixed length of bolt 150mm long, complete all as specified and as directed by Engineer-in-Charge.

S & F mild steel sliding door, bolts, plate type, stove enamelled black with bright bolt not less than 12mm bore, length of bolt 250mm complete all as specified and as directed by Engineer-in-Charge.

M&L preparing new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

M&L preparing new/old surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

S&F reinforced multipurpose boards/ fibre cement flat sheets (contains no Asbestos), sample as per site and as approved by Engineer in Charge as in wall cladding complete all as specified and as directed by Engineer-in-Charge.

M&L galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-in-Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody (for refixing the same) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Point wiring for one light point or one fan point or for one three pin socket point on independent board controlled by one switch with 1100V grade PVC insulated and unsheathed 1.5 Sqmm standard copper conductor in & incl FRLS wire incl casing & caping surface wiring with cutting, chasing and plastering and surface on ceiling with fixing arrng and continuous run 2.5 Sqmm copper earth wire incl cutting changing sunk in MS boxes 1.6mm thick duly painted with two coats of anti corrosive paint outside & aluminum inside covered with 3mm thick hylam brand sheet complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 32.00 above but for one 3 pin socket outlet 5 Amps on same boards.

All as per item No. 32.00 above but 2.5 sqmm PVC insulated unsheathed stranded copper conductor 1100 V grade with continuous 1.5 sqmm copper earth wire for one 3 pin socket outlet 15Amps on independent boards.

Supply and fix in replacement batten holder flush type complete all as specified and as directed by Engineer-in-Charge.

M&Lswitch piano flush button type 5 amps single pole one way complete all as specified and as directed by Engineer-in-Charge.

M&L switch socket outlet combination piano type multipurpose 3 pin 5 Amps flush type single pole complete all as specified and as directed by Engineer-in-Charge.

M&L switch socket outlet combination piano type multipurpose 3 pin 5 Amps & 3 pin 15 Amps flush type single pole complete all as specified and as directed by Engineer-in-Charge.

Taking down of existing UNSV FTL/LED fitting any size complete all as specified and as directed by Engineer-in-Charge.

M&L ceiling rose surface bakelite ISI mark two to three terminals complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing 18 Watt E-Lite LED gREEN Decorative ultra slim round profile LED lighting fixture with co extruded polycarbonate body, environmental friendly, energy efficient size of 60.6 cm complete all as specified and as directed by Engineer-in-Charge. MAKE HAVELLS as per cat No LHEXBLP7UN1W018

Taking down of existing DBs any size complete all as specified and as directed by Engineer-in-Charge.

S&F for LED bulb/lamp of 7/9 Watts B22 Pin Type Cool Daylight complete all as specified and as directed by Engineer-in-Charge. Make Havells Cat No: LHLDAGUEML8X007

M&L MCB DB TPN 16 WAY ccomplete all as specified and as directed by Engineer-in-Charge. Make : Indoasian.

M&L MCB TPN 25 Amp 415 Volts complete all as specified and as directed by Engineer-in-Charge. Make : Indoasian.

M&L MCB SP 06-16 Amps complete all as specified and as directed by Engineer-in-Charge. Make : Indoasian.

Material and laying cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 4 core complete all as specified and as directed by Engineer-in-Charge.

M&L for white cover plate with frame 6 module complete all as specified and as directed by Engineer-in-Charge.

M&L for white cover plate with frame 8 module complete all as specified and as directed by Engineer-in-Charge.

Kalap Engineers and Builders

M/S VIJAY TRADERS