Pdg. HVAC System in the Block-D, Civil Hospital, Sec.-6, Panchkula.

Amount

[23.23.6..2]MISCELLANEOUS 6..2. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 200 X 50 X 2 mm [Through Rate]

[23.23.6.3]MISCELLANEOUS 6.3. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 375 X 50 X 2 mm [Through Rate]

[23.23.6.4]MISCELLANEOUS 6.4. Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. MS perforated cable tray painted with powder coating 600 X 50 X 2 mm [Through Rate]

[23.23.7.2]MISCELLANEOUS 7.2. Supply and erection of cable tray cover made of 1.25 mm thick GI sheet as required including erection of the same on existing cable tray with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. GI cable tray Cover , suitable for cable tray of 200 X 50 X 2 mm [Through Rate]

[23.23.7.3]MISCELLANEOUS 7.3. Supply and erection of cable tray cover made of 1.25 mm thick GI sheet as required including erection of the same on existing cable tray with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. GI cable tray Cover , suitable for cable tray of 375 X 50 X 2 mm metre [Through Rate]

[23.23.7.4]MISCELLANEOUS 7.4. Supply and erection of cable tray cover made of 1.25 mm thick GI sheet as required including erection of the same on existing cable tray with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. GI cable tray Cover , suitable for cable tray of 600 X 50 X 2 mm [Through Rate]

[24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.1.12]EARTHING AND LIGHTENING ARRESTOR 12. Supplying and laying 6 S.W.G G.I. wire at 0.50 m below ground level from earth electrode including thimbles, soldering etc. as required. [Through Rate]

[24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required. [Through Rate]

[24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode. [Through Rate]

[24.1.9]EARTHING AND LIGHTENING ARRESTOR 9. Providing and fixing 25 mm x5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required. [Through Rate]

[24.13.12]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 12. 6 Sq mm 4 core (Arm.) [Through Rate]

[24.13.18]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 18. 10 Sq mm 4 core (Arm.) [Through Rate]

[24.13.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 24. 16 Sq mm 4 core (Arm.) [Through Rate]

[24.13.30]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 30. 25 Sq mm 3.5 core (Arm.) [Through Rate]

[24.13.6]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 6. 4 Sq mm 4core (Arm.) [Through Rate]

[24.13.88]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 88. 240 Sq mm 3.5 core (Arm.) [Through Rate]

[25.1.1]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 1. 300mm dia. [Through Rate]

[25.1.10]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 10. 40mm dia. [Through Rate]

[25.1.2]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 2. 250 mm dia [Through Rate]

[25.1.3]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 3. 200mm dia. [Through Rate]

[25.1.4]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 4. 150mm dia. [Through Rate]

[25.1.5]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 5. 125mm dia. [Through Rate]

[25.1.6]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 6. 100mm dia. [Through Rate]

[25.1.7]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 7. 80mm dia. [Through Rate]

[25.1.8]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 8. 65mm dia. [Through Rate]

[25.1.9]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 9. 50mm dia. [Through Rate]

[25.3.3]Supplying, fixing, testing and commissioning of Butterfly valves PN 16 rated without insulation for water circulation as per specifications. 3. 200mm dia. [Through Rate]

[25.3.4]Supplying, fixing, testing and commissioning of Butterfly valves PN 16 rated without insulation for water circulation as per specifications. 4. 150mm dia. [Through Rate]

[25.3.6]Supplying, fixing, testing and commissioning of Butterfly valves PN 16 rated without insulation for water circulation as per specifications. 6. 100mm dia. [Through Rate]

[25.3.7]Supplying, fixing, testing and commissioning of Butterfly valves PN 16 rated without insulation for water circulation as per specifications. 7. 80mm dia. [Through Rate]

[25.3.8]Supplying, fixing, testing and commissioning of Butterfly valves PN 16 rated without insulation for water circulation as per specifications. 8. 65mm dia. [Through Rate]

[25.4.1]Supplying, fixing, testing and commissioning o NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end and PN 16 pressure rating as specified. 1. 200mm dia. [Through Rate]

[25.4.4]Supplying, fixing, testing and commissioning o NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end and PN 16 pressure rating as specified. 4. 100mm dia. [Through Rate]

[25.5.1]Supplying, fixing, testing and commissioning o BALANCING VALVE flanged end and PN 16 pressure rating as specified. 1. 200mm dia. [Through Rate]

[25.5.2]Supplying, fixing, testing and commissioning o BALANCING VALVE flanged end and PN 16 pressure rating as specified. 2. 150mm dia. [Through Rate]

[25.6.1]Supplying, fixing, testing and commissioning o STRAINER flanged end and PN 16 pressure rating as specified. 1. 200mm dia. [Through Rate]

[25.6.4]Supplying, fixing, testing and commissioning o STRAINER flanged end and PN 16 pressure rating as specified. 4. 100mm dia. [Through Rate]

[25.7.1]Supply, installation, and commissioning of factory/site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 1. Thickness 0.63 mm sheet [Through Rate]

[25.7.2]Supply, installation, and commissioning of factory/site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 2. Thickness 0.80 mm sheet [Through Rate]

[25.7.3]Supply, installation, and commissioning of factory/site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 3. Thickness 1.00 mm sheet [Through Rate]

[25.7.4]Supply, installation, and commissioning of factory/site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 4. Thickness 1.25 mm sheet [Through Rate]

[9.42.1]Providing and fixing flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately): 1. 12 mm thick [Through Rate]

[9.46.3]Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts and bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer`s specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 3. 12.5 mm thick tapered edge gypsum moisture resistant board [Through Rate]

Supply, installation, testing and commissioning of End Suction Back pull out type centrifugal condenser water pumping set complete with motor, base frame. The pump motor shall be suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. Pumps shall be complete as per specifications and shall have operating parameters as given below including foundation / related Civil work with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Pumping set with bronze impeller (1 W plus 1 S) Cap 1300 USGPM HEAD 22-25 Meter Make :- Xylem/Grundfoss/Armstrong/Lubi

Supply, installation, testing and commissioning of End Suction Back pull out type centrifugal chilled water pumping set with VFD etc. complete with motor, base frame. The pump motor shall be suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. Pumps shall be complete as per specifications and shall have operating parameters as given below including foundation / related Civil work with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work:- Pumping set with bronze impeller (1 W plus 1 S) Cap 780 USGPM HEAD 32 meter Make :- Xylem/Grundfoss/Armstrong/Lubi

Supply, installation, testing and commissioning hot water generator in steps of capacity 350 KW including foundation / related Civil work with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make :- Rapid Cool / KEPL / Emerald

Supply, installation, testing and commissioning of induced draft cooling towers of cap 400 TR. Each tower shall be complete with distribution system, fillings, louvers, Hot dipped galvanized ladder, axial flow fan and motor. Motor (IP:55) shall be suitable for 415 ± 10% volts, 50 cycles, 3 phase power supply including foundation / related Civil work with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work Capacity: To Cool 1600 USGPM of water at parameters indicated above Make :- Advance / Delta / Mihir / Bell

Supply, installation, testing and commissioning of factory fabricated Double Skin Chilled Water Air- handling unit (Floor Mounted / Ceiling Suspended) of capacity 7500 CFM, Static Pressure of WC 65mm, Cooling Coil Deep 6 Row, Filteration Level 10 Micron, horizontal type fabricated out of extruded aluminium section consisting with 0.63 mm pre-plasticized/pre-coated Galvanized steel sheet outside and 0.63 mm plain aluminium sheet inside with blower, blower section and Blower shall be DIDW forward / Backward Curved blade from and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, Multi Row deep cooling coil made of Aluminium finned Copper tube with coil section, pre - filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% , stainless steel drain pan made out of 18 G sheet duly insulated complete with motor and belt drive package etc. The AHU panels shall be insulated with 48 plus 2 mm thick and 38 Kg/m³ density PU foam. The motor and blower assembly shall be mounted on Aluminium extruded section with thermal break profile including digital pressure guage and digital temperature indication (IN and OUT), attenuator to maintain low noise level as required with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Zeco / Edgetech / Citizen

Supply, installation, testing and commissioning of factory fabricated Double Skin Chilled Water Air- handling unit (Floor Mounted / Ceiling Suspended) of capacity 6000 CFM, Static Pressure of WC 65mm, Cooling Coil Deep 6 Row, Filteration Level 10 Micron, horizontal type fabricated out of extruded aluminium section consisting with 0.63 mm pre-plasticized/pre-coated Galvanized steel sheet outside and 0.63 mm plain aluminium sheet inside with blower, blower section and Blower shall be DIDW forward / Backward Curved blade from and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, Multi Row deep cooling coil made of Aluminium finned Copper tube with coil section, pre - filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% , stainless steel drain pan made out of 18 G sheet duly insulated complete with motor and belt drive package etc. The AHU panels shall be insulated with 48 plus 2 mm thick and 38 Kg/m³ density PU foam. The motor and blower assembly shall be mounted on Aluminium extruded section with thermal break profile including digital pressure guage and digital temperature indication (IN and OUT), attenuator to maintain low noise level as required with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Zeco / Edgetech / Citizen

Supply, installation, testing and commissioning of factory fabricated Double Skin Chilled Water Air- handling unit (Floor Mounted / Ceiling Suspended) of capacity 5000 CFM, Static Pressure of WC 65mm, Cooling Coil Deep 6 Row, Filteration Level 10 Micron, horizontal type fabricated out of extruded aluminium section consisting with 0.63 mm pre-plasticized/pre-coated Galvanized steel sheet outside and 0.63 mm plain aluminium sheet inside with blower, blower section and Blower shall be DIDW forward / Backward Curved blade from and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, Multi Row deep cooling coil made of Aluminium finned Copper tube with coil section, pre - filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% , stainless steel drain pan made out of 18 G sheet duly insulated complete with motor and belt drive package etc. The AHU panels shall be insulated with 48 plus 2 mm thick and 38 Kg/m³ density PU foam. The motor and blower assembly shall be mounted on Aluminium extruded section with thermal break profile including digital pressure guage and digital temperature indication (IN and OUT), attenuator to maintain low noise level as required with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Zeco / Edgetech / Citizen

Supply, installation, testing and commissioning of factory fabricated Double Skin Chilled Water Air- handling unit (Floor Mounted / Ceiling Suspended) of capacity 4000 CFM, Static Pressure of WC 65mm, Cooling Coil Deep 6 Row, Filteration Level 10 Micron, horizontal type fabricated out of extruded aluminium section consisting with 0.63 mm pre-plasticized/pre-coated Galvanized steel sheet outside and 0.63 mm plain aluminium sheet inside with blower, blower section and Blower shall be DIDW forward / Backward Curved blade from and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, Multi Row deep cooling coil made of Aluminium finned Copper tube with coil section, pre - filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% , stainless steel drain pan made out of 18 G sheet duly insulated complete with motor and belt drive package etc. The AHU panels shall be insulated with 48 plus 2 mm thick and 38 Kg/m³ density PU foam. The motor and blower assembly shall be mounted on Aluminium extruded section with thermal break profile including digital pressure guage and digital temperature indication (IN and OUT), attenuator to maintain low noise level as required with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Zeco / Edgetech / Citizen

Supply, installation, testing and commissioning of factory fabricated Double Skin Chilled Water Air- handling unit (Floor Mounted / Ceiling Suspended) of capacity 3500 CFM, Static Pressure of WC 65mm, Cooling Coil Deep 6 Row, Filteration Level 10 Micron, horizontal type fabricated out of extruded aluminium section consisting with 0.63 mm pre-plasticized/pre-coated Galvanized steel sheet outside and 0.63 mm plain aluminium sheet inside with blower, blower section and Blower shall be DIDW forward / Backward Curved blade from and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, Multi Row deep cooling coil made of Aluminium finned Copper tube with coil section, pre - filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% , stainless steel drain pan made out of 18 G sheet duly insulated complete with motor and belt drive package etc. The AHU panels shall be insulated with 48 plus 2 mm thick and 38 Kg/m³ density PU foam. The motor and blower assembly shall be mounted on Aluminium extruded section with thermal break profile including digital pressure guage and digital temperature indication (IN and OUT), attenuator to maintain low noise level as required with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Zeco / Edgetech / Citizen

Supply, installation, testing and commissioning of factory fabricated Double Skin Chilled Water Air- handling unit (Floor Mounted / Ceiling Suspended) of capacity 3000 CFM, Static Pressure of WC 65mm, Cooling Coil Deep 6 Row, Filteration Level 10 Micron, horizontal type fabricated out of extruded aluminium section consisting with 0.63 mm pre-plasticized/pre-coated Galvanized steel sheet outside and 0.63 mm plain aluminium sheet inside with blower, blower section and Blower shall be DIDW forward / Backward Curved blade from and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, Multi Row deep cooling coil made of Aluminium finned Copper tube with coil section, pre - filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% , stainless steel drain pan made out of 18 G sheet duly insulated complete with motor and belt drive package etc. The AHU panels shall be insulated with 48 plus 2 mm thick and 38 Kg/m³ density PU foam. The motor and blower assembly shall be mounted on Aluminium extruded section with thermal break profile including digital pressure guage and digital temperature indication (IN and OUT), attenuator to maintain low noise level as required with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Zeco / Edgetech / Citizen

Supply, installation, testing and commissioning of 48000 BTU/HR (4 Tr.) factory fabricated four way hydronic type cassette units complete with valve package and cordless remote with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Carryair / Bathuria/ Universal / Carrier

Supply,Installation , testing and commissioning of fan coil unit of 1.0 TR nominal capacity suitable for both heating and cooling (400 CFM) and air flow as per the specifications, complete with auxillary drain pan. Fan coil unit shall be supplied with approved make of factory fitted adequately sized insulated (with nitrile foam), two way modulating valves, insulated brass ball valves-one with Y strainer, and the other without Y strainer installations complete with room thermostat for fan speed control, Remote Control associated conduiting and wiring between the thermostate etc. The cost of Copper pipe connection between chilled water pipes and units along with all accessories upto 1 meter are included in the cost of each unit and same shall be born by the tenderer (if required). Cost of fan coil unit shall be inclusive of approved make room thermostat (heating and cooling, with fan speed control), Two Way Valves along with all accessories and associated MS conduiting and wiring etc.between the thermostat and two way valve , TF Canvass Connection double layer, for a standard length of approximately 5-7 M per fan coil unit. Providing and fixing in position the following Fan Coil units complete with all valves and accessories as described above including all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make: Edgetech / ZECO / System Air / Flaktswood

Supply,Installation , testing and commissioning of fan coil unit of 1.5 TR nominal capacity suitable for both heating and cooling (600 CFM) and air flow as per the specifications, complete with auxillary drain pan. Fan coil unit shall be supplied with approved make of factory fitted adequately sized insulated (with nitrile foam), two way modulating valves, insulated brass ball valves-one with Y strainer, and the other without Y strainer installations complete with room thermostat for fan speed control, Remote Control associated conduiting and wiring between the thermostate etc. The cost of Copper pipe connection between chilled water pipes and units along with all accessories upto 1 meter are included in the cost of each unit and same shall be born by the tenderer (if required). Cost of fan coil unit shall be inclusive of approved make room thermostat (heating and cooling, with fan speed control), Two Way Valves along with all accessories and associated MS conduiting and wiring etc.between the thermostat and two way valve , TF Canvass Connection double layer, for a standard length of approximately 5-7 M per fan coil unit. Providing and fixing in position the following Fan Coil units complete with all valves and accessories as described above including all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make: Edgetech / ZECO / System Air / Flaktswood

Supply,Installation , testing and commissioning of fan coil unit of 2.0 TR nominal capacity suitable for both heating and cooling (800 CFM) and air flow as per the specifications, complete with auxillary drain pan. Fan coil unit shall be supplied with approved make of factory fitted adequately sized insulated (with nitrile foam), two way modulating valves, insulated brass ball valves-one with Y strainer, and the other without Y strainer installations complete with room thermostat for fan speed control, Remote Control associated conduiting and wiring between the thermostate etc. The cost of Copper pipe connection between chilled water pipes and units along with all accessories upto 1 meter are included in the cost of each unit and same shall be born by the tenderer (if required). Cost of fan coil unit shall be inclusive of approved make room thermostat (heating and cooling, with fan speed control), Two Way Valves along with all accessories and associated MS conduiting and wiring etc.between the thermostat and two way valve , TF Canvass Connection double layer, for a standard length of approximately 5-7 M per fan coil unit. Providing and fixing in position the following Fan Coil units complete with all valves and accessories as described above including all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make: Edgetech / ZECO / System Air / Flaktswood

Supply,Installation , testing and commissioning of fan coil unit of 3.5 TR nominal capacity suitable for both heating and cooling (1400 CFM) and air flow as per the specifications, complete with auxillary drain pan. Fan coil unit shall be supplied with approved make of factory fitted adequately sized insulated (with nitrile foam), two way modulating valves, insulated brass ball valves-one with Y strainer, and the other without Y strainer installations complete with room thermostat for fan speed control, Remote Control associated conduiting and wiring between the thermostate etc. The cost of Copper pipe connection between chilled water pipes and units along with all accessories upto 1 meter are included in the cost of each unit and same shall be born by the tenderer (if required). Cost of fan coil unit shall be inclusive of approved make room thermostat (heating and cooling, with fan speed control), Two Way Valves along with all accessories and associated MS conduiting and wiring etc.between the thermostat and two way valve , TF Canvass Connection double layer, for a standard length of approximately 5-7 M per fan coil unit. Providing and fixing in position the following Fan Coil units complete with all valves and accessories as described above including all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make: Edgetech / ZECO / System Air / Flaktswood

Providing and fixing in position MS `C` class pipe 25 MM dia (With Insulation), cut to required length and installed with welded joints, providing and fixing all necessary fittings such as bends, elbows, tees, reducers, flanges, sockets etc. Chilled water piping shall be insulated with 50 mm thick EPS Pipe Section (TF Quality) covered with 2 layers of sand cement plaster each layer of 8 mm for exposed piping or 26 SWG Aluminium cladding over piping for indoor installation with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of wor. Make : Jindal / TATA / Parkash Surya

Providing and fixing in position MS `C` class pipe 32 MM dia (With Insulation), cut to required length and installed with welded joints, providing and fixing all necessary fittings such as bends, elbows, tees, reducers, flanges, sockets etc. Chilled water piping shall be insulated with 50 mm thick EPS Pipe Section (TF Quality) covered with 2 layers of sand cement plaster each layer of 8 mm for exposed piping or 26 SWG Aluminium cladding over piping for indoor installation with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of wor. Make : Jindal / TATA / Parkash Surya

Providing and fixing in position the 80mm dia Three Way Valve with Actuator, Heating / Cooling Thermostate for Air Handling units with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Honeywell / Rapid Cool

Providing and fixing in position the 65mm dia Three Way Valve with Actuator, Heating / Cooling Thermostate for Air Handling units with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Honeywell / Rapid Cool

Providing and fixing in position the 50mm dia Three Way Valve with Actuator, Heating / Cooling Thermostate for Air Handling units with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Honeywell / Rapid Cool

Supply and Erection of Digital Temperature indicator K type with sensor with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make :- Fiebig / H Guru.

Providing and fixing in position industrial type Digital SS pressure gauges having dial size 100 mm complete with SS syphon and cock with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make :- Fiebig / H Guru.

Supply and Erection of closed Pressurized Expansion Tank capacity 500 Ltrs. with highest pressure of tank is should be designed to withstand, typically around 10 bar (150 PSI) and pre-charge pressure is 1.9 bar (28 PSI) and insulated with 50mm thick EPS (Expanded Polystyrene) slab covered with Vapour Barrier, Chicken Wire Mesh and Finished with Sand Cement Plaster with overflow valve, float valve with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make :- Sintex / Ploycon / ANERGY

Supply and Erection of 25 mm dia water flow switch including all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Rapid Cool / Anergy.

Supply , installation , testing and commissioning of condensate 40mm dia drain water piping of GI `Medium` class complete with Medium Class fittings like elbows, tees, reducers bends, MS flanges, supports, welding, painting 25 mm thick EPS insulation etc. as required conforming to standard specifications with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Jindal / TATA / Parkash Surya..

Supply and Erection of 25 mm dia automatic purging valves (Air Vent) including all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Rapid Cool / Anergy

Supply , installation , testing and commissioning of Axial Flow Fan - 5900 CFM SP 25 mmwg, with suitable motor and drive assembly, with all accessories and fire rated flexible connections, mounting frame hangers etc. Motor shall be suitable for 415 V plus /- 10%, 3 phase, 4 wire, 50 plus /- 3% Hzs, electric supply with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Air Flow/ Humidin / Greenheck.

Supplying and fixing of powder coated extruded aluminium Supply Air Grills / diffusers with aluminium volume control dampers as per specifications with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make- Swirl Air/ Systemair/Carryair

Supplying and fixing of powder coated extruded aluminium return Air Grills / diffusers without volume control dampers as per specifications with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make- Swirl Air/ Systemair/Carryair

Supplying and fixing of Eye Ball Jet Nozzle double skin power coated of size 465 CMH, 8.0 Pa, less than 20 dB (A), throw 20 meter for long distance air throw applications with low noise. The outlet direction can be regulated manually. The ball can be rotated / moved in angle of 30 degrees from the center line in any directionwith all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Swirl Air/ Systemair/Carryair

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make - Swirl Air/ Systemair/Carryair

Supply and erection of Actuators Motor for Fire Dampers with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Belimo/ Siemens/ Falcon.

Supplying and fixing of Fresh air intake louvers with bird screen and dampers (Aluminium extruded only) with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make:- Swirl Air/ Systemaire/Carryair

Supplying and fixing of 9 mm thick closed cell Nitrile rubber (indoor application) duct insulation with insulation `A` class anti microbiol density 50 Kg/m³. Applied by Adhesive, conforming to standard specification with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Armacell/K-Flex/Arma Flex

Supplying and fixing of 19 mm thick closed cell Nitrile rubber (indoor application) duct insulation with insulation `A` class anti microbiol density 50 Kg/m³. Applied by Adhesive, conforming to standard specification with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Armacell/K-Flex/Arma Flex

Supplying and fixing of 19 mm thick closed cell Nitrile rubber and covered with fibre cloth and Glucobond coating (outdoor application) duct insulation with insulation `A` class anti microbiol density 50 Kg/m³. Applied by Adhesive, conforming to standard specification with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Armacell/K-Flex/Arma Flex

Supplying and fixing of Acousting Insulation of Duct from inside with covered 10 mm open cell insulation, duct insulation with insulation `A` class anti microbiol density 50 Kg/m³. Applied by Adhesive, conforming to standard specification with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work. Make : Armacell/K-Flex/Arma Flex

Supply and Erection of PVC insulated and PVC Round Sheathed Copper Cable 1.5 Sqmm x 2 Core, Multicore Annealed Bare Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 to complete the job in all respect up to the entire satisfaction of Engineer in Charge of work. Make as per approved List

Supply and Erection of PVC insulated and PVC Round Sheathed Copper Cable 1.5 Sqmm x 3 Core, Multicore Annealed Bare Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 to complete the job in all respect up to the entire satisfaction of Engineer in Charge of work. Make as per approved List

Supply and Erection of PVC insulated and PVC Round Sheathed Copper Cable 2.5 Sqmm x 2 Core, Multicore Annealed Bare Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 to complete the job in all respect up to the entire satisfaction of Engineer in Charge of work. Make as per approved List

Supply and Erection of PVC insulated and PVC Round Sheathed Copper Cable 2.5 Sqmm x 4 Core, Multicore Annealed Bare Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 to complete the job in all respect up to the entire satisfaction of Engineer in Charge of work. Make as per approved List

Pdg. Minor Civil work i.e foundation of Chiller, Pump Set, Cooling tower, Hot water generator, making holes in brick work for ducting, piping including repair with mixture of sand and cement with all labour and petty material required to complete the job of central air conditioning in the building with repair work in all respect upto the entire satisfaction of Engineer-in-Charge of work..

Weather proof isolator for cooling tower SITC of Outdoor weather proof switch box of continuous welded construction, fabricated out of 2 mm thick GI sheet complete with water tight gasket with front openable and lockable door including earthing, painting glands, danger boards etc. Suitable for mounting on MS angle frame consisting of revelant specification and drawings. Make as per approved list. -2nos x 63 Amp 4 POLE isolators (Siemens/Schnieder/ABB/LandT) for cooling tower near cooling tower

Control Console Panel SITC of floor mounted desk type Control Consiole in A/c plant room containing various indications and controls for the A.C. system comprising of 2 Nos. chilling machine, 2 Nos. pumps, 2 Nos. cooling tower, 94 Nos AHU/CSU with test push buttons facility. The panel shall be fabricated from minimum 1.6 thick M.S. Powder coated sheet of approved design. The A.C. module of the Central Control shall have the following accessories: -Status indication (ON, OFF) for each compressor for each chilling machine and all pumps. -Push Buttons and Indication lamps for remote start and stop and status indication for each of the AHUs. -Push Buttons and Indication lamps for remote start and stop and status indication(ON, OFF) for each of the 2 Nos. Cooling Tower motors and low level indication for each of 2Nos. cooling tower. -Hooter and Flashing lamps to indicate operation of any safety/shut down with necessary contractors, accept, reset and test push buttons complete as per specifications. Make as per approved list

Insulation on 250mm dia Butterfly Valves by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 150mm dia Butterfly Valves by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 80mm dia Butterfly Valves by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 65mm dia Butterfly Valves by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 200mm dia Non Return Valve by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 125mm dia Non Return Valve by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 200mm dia Balancing Valve by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 150mm dia Balancing Valve by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 200mm dia Y-Stainer Valve by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Insulation on 100mm dia Y-Stainer Valve by providing expanded polystrene moulded TF Quality/moulded PUF sections of density 20Kg/m3 or using nitrile rubber 20 mm thick etc as required, complete : Make : Beardsell, Lloyed

Supplying and fixing of insulation on 300 MM Pipe DIA 75 mm Thick pipe with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500 g polythene faced hessain and then applying 0.6 mm aluminium sheet cladding complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 250MM Pipe DIA 75 mm Thick pipe with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500 g polythene faced hessain and then applying 0.6 mm aluminium sheet cladding complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 200 MM Pipe DIA 75 mm Thick pipe with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500 g polythene faced hessain and then applying 0.6 mm aluminium sheet cladding complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 150 MM Pipe DIA 75 mm Thick Insulation with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with water barrier and covered with 7 mil. glass cloth duly painted with UV paint as per site requirement to complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 125MM Pipe DIA 50 mm Thick Insulation with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with water barrier and covered with 7 mil. glass cloth duly painted with UV paint as per site requirement to complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 100MM Pipe DIA 50 mm Thick Insulation with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with water barrier and covered with 7 mil. glass cloth duly painted with UV paint as per site requirement to complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 80MM Pipe DIA 50 mm Thick Insulation with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with water barrier and covered with 7 mil. glass cloth duly painted with UV paint as per site requirement to complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 65MM Pipe DIA 50 mm Thick Insulation with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with water barrier and covered with 7 mil. glass cloth duly painted with UV paint as per site requirement to complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 50MM Pipe DIA 50 mm Thick Insulation with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with water barrier and covered with 7 mil. glass cloth duly painted with UV paint as per site requirement to complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Supplying and fixing of insulation on 40MM Pipe DIA 50 mm Thick Insulation with FR quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with water barrier and covered with 7 mil. glass cloth duly painted with UV paint as per site requirement to complete with feltstrip at joints repairing etc. as per specifications and as required complete in all respect. Make : Beardsell, lloyed

Less buyback old dismantled scrap (pipe and ducting etc.)

Water Cooled Chilling Unit:- Supply, Installation, testing and commissioning of AHRI Certified Water Cooled Screw type chilling unit of 325 ± 3% TR actual capacity with company fitted VFD at the parameters indicated below complete with Semihermitic/ hermetic compressor. Helical Rotary Mono / twin Screw with Single / two number independent refrigerant circuit with single/multiple compressor (chiller compressor sourced from third party manufacturer under labelling program is not acceptable.) with 25% to 100% capacity control range with one point testing at factory bed, TERC squirrel cage motor, factory insulated cooler, Water cooled condenser, vibration, isolators, integral refrigerant piping and wiring, flow switches at chiller and condensor outlets, first charge of refrigerant and lubricant, microprocessor based control panel, accessoreies as required. Motor shall be suitable for 415 plus - 10% V, 50 Hz, 3 ph AC supply as per specifications with foundation / related Civil work all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer in Chagre of work. Cooler:- Chilled Water in: 12° C (54° F) Chilled water out 7.2° C (44° F) Chilled water flow rate: 840 USGPM Fouling Factor:- 0.0005 FPS Condenser :- Condenser water in :- 32.22° C Condenser water out : 36.44°C Condenser water flow rate: 1400 USGPM Fouling Factor :-0.001 FPS COP at AHRI conditions shall as per ECBC Plus / BEE 4 star labelling. Make :- Climavenata / Daikin / Danhum Bush / Carrier / Trane.

Hemcool Engineers (BID ID -1326171)

modern cooling solution (BID ID -1326057)