Special repair to building No MH 13 (Class IV accn) at Mily Station Kannur under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing with ceiling tiles all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size including tilting fillets all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

All as per item No 4 here in before but except timber all as specified and directed. Note : Serviceable tmber scantling obtained from item No 3 shall be re used.

M&L for mild steel structural work in tubular trusses including special shaped washer, etc, complete using ERW or induction butt welded tubes etc Fe 410W (Gde E-250) quality B all as specified and directed.

M&L for MS Rolled sections as Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) using Fe 410-w (Gde E -250) quality A all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge/valley gutter/roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F PVC (SWR) pipe 180mm bore as in half round gutters including suitable drop ends/stop end and fixing with MS/PVC clamps suitable for steel sheet roof all as specified and directed.

S&F PVC (SWR) pipe 75mm bore as in down take pipe single socketed with solvent joints fixed to wall with suitable clamps all as specified and directed.

M&L for preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

All as per item No 12 here in before but one coat of creosote oil on old treated surfaces all as specified and directed.

M&L for preparation of new or old untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

All as per item No 16 here in before but except stone all as specified and directed. Note : Serviceable laterite stone obtained from item No 15 shall be re used.

Taking down chowkats with shutters any description n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters any description exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

Taking down door shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm all as directed.

Taking down door shutters of any description not exceeding 1 Sqm all as directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L Cutting openings through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises old masonry built in cement mortar all as specified and directed.

Providing, cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in hold fast, roof kerbs or mud stops, rounded or chamfered on edges including necessary form work all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 25 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

M&L for second class hardwood, panelled shutter 35mm thick (any number of panels) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated, edges of framing plain, chamfered or rounded, fitted with cut and mitred and rebated sash bars, divided into squares, for securing glass gauze, etc; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(b) all as specified and directed.

S&F 4mm thick frosted sheet glass, ordinary quality and glazing with beads fixed with metal panel pins in squares not exc 0.50 Sqm in each pane all as specified and directed.

S&F mild steel framed work such as grills gratings, etc, with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 75mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size fixed with stainless steel screws all as specified.

S&F 150mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L preparing old treated wooden surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel painting all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treating back of chowkats,area tarred exc. 0.1 sqm but n.exc 0.5 sqm with tar or coal tar black paint each all as specified and directed.

M&L Preparing surfaces of wood and wood based materials, steel and iron work, small articles such as stop, covers, gully gratings, holdfasts, etc., area n exc 0.1 sq. m each each treated with tar or coal tar black paint each all as specified and directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

Demolition of reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (reinforcement cut as required to facilitate demolition) and removing debris outside MD land all as directed.

M&L for reinforced cement concrtet 1:2:4 (nominal mix), type B1 using 20mm graded stone aggregate as in lintels not exc 1.50m span, cills, steps, seismic and other similar bands including necessary form works complete all as specified and directed. Note : Reinforcement shall be measured and paid seperately.

M&L for RCC (1:2:4) type B1 using 20mm graded stone aggregate as in slabs supported on walls all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs and similar work, not exceeding 200 mm thick (horizontal or sloping ), rough finished surface of concrete flat all as specified and directed.

M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings openings in concrete walls, floor and roofs n exc 20 cm wide rough finished surface of concrete all as specified and directed.

Material & Labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

All as per Sl item No 49 above, but 6mm dia and over upto and including 10mm dia as in stirrups, spacers and binders all as specified and directed.

Material & Labour for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

M & L for plain cement concrete (1:4:8), type D2 using 40mm graded trap stone aggregate as in foundation , filling, mass concrete etc all as specified and directed

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even all as specified and directed.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. all as specified and directed.

M&L for coloured joint free non skid ceramic tiles, 7 to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles 300x200x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:4) on concrete surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M & L for 75 mm thick plain cement concrete 1:3:6, type C1 using 20mm graded aggregate as in plinth protection etc including necessary form work complete all as specified and directed

M&L for hard core of guage n.exc 63mm broken stone or boulders, deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface all as specified and directed

S&F 1000 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 25 mm bore dia all as specified and directed.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes upto 20mm bore all as directed.

S&F for 15mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings or in floors etc. all as specified and directed.

S&F for 20mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

Cutting chases on wall n exc 10cm girth for concealing water tubing 15/20mm dia and making good the surface with plastering in cement mortar 1:4 and finish to match the existing surface complete all as directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

M&L PVC (SWR) pipe type 'B' 110mm bore single socketed with solvent cement joints fixed to wall using suitable clamps all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints fixed to wall using suitable clamps all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

S&F 75 mm bore, PVC (SWR) bends with access door all as specified and directed

S&F 75 mm bore, PVC (SWR) bends all as specified and directed

S&F grating square 150mm size of PTMT complete all as specified and as directed.

Excavations in trenches not exceeding 1.50m wide and not exceeding 1.50m is depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes etc not exceeding 10 sqm on plan and not exceeding 1.50m in depth and getting out hard / dense soil all as specified and directed .

Returning and filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soil obtained from excavation all as directed

Removing surplus excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

S&F in repairs Vitreous China squatting pan “Orissa” pattern, of size 580 x 440 mm white, with integral foot rests, (excluding flushing cistern and flush pipe), including provision of lime concrete bedding, connection to trap and to flushing pipe, anti-syphonage pipe, etc and joint between flushing pipe and socket of WC pan, complete and making good to the floor all as specified and directed.

S&F in repairs PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density PVC flush pipe all as specified and directed.

S&F Stainless steel sinks 1mm thick with plugs, washers and waste; including bedding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm, bowl size 410 x 330 x 160mm etc complete all as specified and directed.

S&F in repair Vitreous China Wash basin, white, flat back, size 580 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F 15mm pillar taps, cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

Supply and fix PVC connecton 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F bib tap 15mm dia, chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S&F stop cock 15mm bore cast copper alloy, chromium plated, fancy type screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F stop cock 15mm bore cast copper alloy, chromium plated, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F stop cock 20mm bore cast copper alloy, chromium plated, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F tubular towel rail brass, chromium plated, D type, 60cm long between flanges fixed to wall with wooden plugs with chromium plated brass screws all as specified and directed.

Taking out and cleaning of existing roof treatment of any description by wire brushing and cleaning top surface with water and remove the rubbish to outside MD land etc. M& L for water proofing treatment to RCC roof with APP modified prefabricated five layer membrane of 4mm thick and weight not less than 4.00 Kg per Sqm reinforced with non woven polyster matt reinforcement 160g/sqm (weighing not less than 160gms/sqm) having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 800N/Sqcm tearing strength of 180Nm by torch application over a solvent based bitumen primer, Shalitex primer @ 0.20 Kg per Sqm of same manufacturere conf to IS 3384-1986. Membrane shall be laid including minimum 7.5cm side overlap and 10cm end lap. All cracks in roof shall be filled with cement putty using suitable bonding agent (Shalocrete 42) before laying cement plaster all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying 1mm thick acrylic wall care putty and making the surface smooth and even including sanding each layer to receive next new layer, one coat of wall primer and applying two coats of oil emulsion distemper and all as specified and as directed.

M&L for preparation of new wall surfaces and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, alkali and fungal resistance , dirt resistance exterior paint of approved shade with silicon additives @ 1.43 litre per 10 sqm over a coat of exterior primer @ 0.90 litre per 10sqm all as specified and directed.

M & L for complete removal of existing treatment and preparation of newly plastered surfaces of wall and applying 1mm thick acrylic wall care putty and making the surface smooth and even including sanding each layer to receive next new layer, one coat of wall primer and applying two coats of oil emulsion distemper and all as specified and as directed.

M & L for complete removal of existing treatment preparation of new wall surfaces and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, alkali and fungal resistance , dirt resistance exterior paint of approved shade with silicon additives @ 1.43 litre per 10 sqm over a coat of exterior primer @ 0.90 litre per 10sqm all as specified and directed.

S & F in repairs brass chromium plated shower rose 125 mm dia suitable to 15mm bore pipe complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power socket complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc. all as directed

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLSH cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit concealed to wall and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc with fixing material including terminal box made out of 1.22mm thick MS sheet concealed in wall covered with laminated sheet top cover of 3mm thick cadmium plated screws with cup washer including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLSH cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch. Note for itm No 99 to 102 : (a) wiring shall be done by using colour code ie. Red, Yellow, Blue and earth wire shall be green colour.

All as per item No 99 here in before but for One 3 Pin, 5 Amps socket on same board with other switches all as specified and directed.

All as per item No 99 here in before but for One 3 Pin, 5 Amps switch socket combination on independent board all as specified and directed.

All as per item No. 99 on here in before but for one 3 pin 15 amp switch socket combination on independent board with 2.5Sqmm unsheathed PVC insulated copper conductor FRLSH cable including 2.5 Sqmm PVC insulated copper cable for earth continuity conductor complete all as specified.

S & F switch piano flush type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose round shape, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S & F switch socket combination, 5pin 5/6 Amps, multipurpose, flush type, non-interlocking type, including connecting up electrically complete all as specified and directed.

S & F switch socket combination, 2 in 1, 5 &15 Amps, multipurpose, flush type, non-interlocking type, including connecting up electrically complete all as specified and directed.

S & F socket 5pin 5/6 Amps, multipurpose, flush type, non-interlocking type, including connecting up electrically complete all as specified and directed.

S & F switch bell push, flush type, 240 Volts, single pole, 5 Amps including connecting up electrically all as specified and directed.

S& F calling bell electric AC 240V, single pole, ding dong type and connecting up electrically all as specified and directed.

S & F sheet metal enclosure factory made for MCB DB, SPN 8 way with 200 Amps bus bar, 240 Volt, double door type, fixed/flushed on wall including electrically connecting up and taking down old unserviceable DB complete all as specified and directed.

S & F MCB SPN, 240 Volt, 40Amps including electrically connecting up using wiring lugs all as specified and directed.

S & F MCB SP, 240 Volt, 6 to 32Amps including electrically connecting up using wiring lugs all as specified and directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim square profile linear LED light fittings with extruded polycarbonate, heat sink, environmental friendly, energy efficient ready to use pack of 4 feet 20 W LED 6000K, model LHEXBLP7PN1W020 of Havells or equivalent in Syska or Crompton Greaves with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

S & F LED light fittings mirror type with high output diffuser 2 feet, 10watt, 220 V, AC decorative type with driver holder and LED lamp 6000K, model LHEXBTP7UN1W009 of Havells or of Wipro or of Bajaj with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

S&F stepped type electronic fan regulator, flush type, 200W, SP, 230V connecting up electricallyall as specified and directed.

S&F in repalacement lamp holder, PVC/poly carbonate type with back plate suitable for batten fitting all as directed.

S&F in repalacement LED ball type lamp 10watt all as directed.

Taking down carefully ceiling fan 1200/1400mm sweep with rod from ceiling / roof and refixing the same after repairs including rewinding, replacement of gun metal bushes, capacitor etc , plastic canopy , ceiling fan down rod of suitable length, clamps, nuts, washers, rubber bushes, safety pin etc complete including connecting up with 2 core twisted flexible copper conductor 23/0.0076 from ceiling rose to fan, testing and commissioning all as specified and directed. Note : Rewinding and ball bearing shall be measured and paid seperately.

Rewinding of ceiling fan 1200/1400 mm sweep any type and make, cutting and removing burnt winding wire without damaging stator, removing old insulation of polyester paper, re-winding fan motor with super enameled copper winding wire of same gauge/dia with correct number of turns for auxiliary and main winding, varnishing, baking, soldering new lead of twin core multi-stranded copper conductor cable of size 23/0.0076, assembling and re-fixing, testing and commissioning complete all as specified and directed.

M&L for clamps made out of flat iron (duly painted with enamel paint over red oxide primer) of 40 mm x 4 mm duly bolted with double nuts and washer on existing wooden beams of approx size 300 x 200 mm with and inclusive of fan down rod of 0.5 to 1.5 metre length duly fitted on MS clamps with bolts,nuts with safety pin and twin core twisted multistranded copper flexible wire of size 23/0.0076 from ceiling rose to fan complete all as specified and directed

S&F in replacement sheet metal enclosures distribution boards, VTPN double door 4 way three phase 415 volts MCCB, ISOLATOR & MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete including taking down unserviceable DB all as specified and directed and comprising of the following:- (a) MCCB 4 Pole 160 AMPS AC 415 V 10 KA=01 No as incoming & outgoing MCB SP-12 No 32/40 AMP (Note :- (i)The DB shall be VTPN series of Make: V guard CAT PART No DBVTPN 12W 160A V DD MCCB IC INVIDIA or equivalent of schnider/ABB/Legrand/Havells. (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii) Connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly.

M & L for earthing complete with galvanized steel earth plate electrode 60cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron connected to earthing test point, main DB, panel board, continuous earth lead protected by 15mm bore GI pipe light grade, 20mm bore GI light grade pipe for watering, necessary excavation and earth work in any type of soil, PCC pit, RCC chamber cover with suitable reinforcement complete all as shown on electrical plate No 3 of SSR part-I of 2009 all as specified and directed. Note :- Rate quoted shall deem to include for GI earth and GI pipe lead upto 7.5m length.

M&L for sub main wiring with two runs of single core 6 Sq mm copper conductor FRLSH cable, PVC insulated, unsheathed multistanded, 1100 V grade drawn through and including non metallic rigid PVC all accessories such as bend,elbow,socket,tee saddles etc fixed concealed to wall / fixed to ceiling etc including 4 Sq mm single core copper conductor FRLSH cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly complete all as specified and directed. Note :- 2 runs of 6 Sq mm and one run of 4sqmm copper cable and one run of PVC conduit will be measured as one length.

S & F in replacement PVC moulded, transperant shutter with hinge, meter box of suitable size of make Sintex/National to accomodate single phase electric meter fixed on wall including refixing old meter in the box and electrically connecting up all as directed.

RS ENTERPRISES

T.P.SUNIL KUMAR

M/S AARJAY ASSOCIATES