PROVN OF CONFERENCE CUM OPS ROOM, RECEIPT AND SECURITY STAFF ROOM WITH ATT TOILET AND CERTAIN REV WORKS AT NAA UNDER GE (NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Excavation in trenches, n.exc. 1.5 m wide and n.exc. 1.5 m in depth for foundation, shafts, manholes,laying of cable etc. n.exc. 10 sq m on plan and getting out in soft/loose soil complete all as specified and directed.

Spreading and levelling to under flooring, in layers n. exc. 25 cm thick and well ramming including watering as required for excavated loose soil, as retreived against respective excavation item complete all as specified and directed.

Removing of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm in foundation using excavated soil as retreived against respective excavation item complete all as specified and directed.

M&L for hardcore of gauge n. exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for sand filling under floor or below paver blocks incl. watering and consolidation complete all as specified and directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area using anti termite treatment Chloropyrophos 20% EC chemical complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface using anti termite treatment Chloropyrophos 20% EC chemical complete complete all as specified and directed.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) using anti termite treatment Chloropyrophos 20% EC chemical complete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area using anti termite treatment Chloropyrophos 20% EC chemical complete all as specified and directed.

M & L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall using anti termite treatment Chloropyrophos 20% EC chemical complete all as specified and directed.

M&L for cement concrete in foundations, filling and mass concrete type D-2, 1:4:8 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

M&L for reinforced cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate ) in foundations,including rafts, footings, foundation beams plinth beam bases for columns etc complete all as specified and directed.

M&L for reinforced cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) in columns, posts, struts etc complete all as specified and directed.

M&L for reinforced cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) in beams, lintels etc complete all as specified and directed.

M&L for reinforced cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) in chajjas etc complete all as specified and directed.

M&L for reinforced cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) and finished even and fair in sub -base floor concrete complete all as specified and directed.

M&L for 75mm thick cement concrete using type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) and finished even and smooth without using extra cement in plinth protection complete all as specified and directed.

M&L for 15mm screed bed in cement sand mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for cement concrete in coping, hold fasts using type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) or of similar work, etc. including necessary form work complete all as specified and directed.

M&L for concrete bed to 100mm dia bore drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested; in concrete using type D-2, 1:4:8 bed to drain pipe complete all as specified and directed.

M&L for pre cast reinforced cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) set in cement mortar (1:4) as in man hole covers or similar work, etc. including necessary form work and loading/unloading of the same and fixed in position complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L for brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L for brick work with old size sub- class ‘B’ bricks of CD 75, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick work with old size sub- class ‘B’ bricks of CD 75,straight or curved on plan to any radius, built in cement mortar 1:4 complete all as specified and directed.

M&L for 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork using type B-0, 1:2:4 concrete (using 12.5mm graded crushed stone aggregate) mixed with water proofing compound the weight of cement in proportional shall be as per manufacturer's instruction complete all as specified and directed. Note- (Water proofing compound shall be measured & paid separately under supply only item)

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter in rough finished flat surface of concrete complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished flat surface of concrete complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. in rough finished flat surface of concrete complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc. 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work in rough finished flat surface of concrete complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick(Horizontal or sloping) finished flat complete all as specified and directed.

M&L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F mild steel iron frame for door , window using joist, channel, angle, tee, tubes, flat sections, fixed independently, without connecting plates, etc. conforming to Fe. 290., Gde-E-165 complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using FE-410W (Grade E-250 quality "A") complete all as specified and directed.

S&F wind tie of mild steel sections using tee, angle, tubular/hollow section, channel or flat sections) including necessary holes for screws/nut bolt etc complete all as specified and directed.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; and similar work conforming to Fe. 290, Gde-E-165 complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc. 5cm & n. exc. 10cm long and 5mm to 10mm dia of neck complete in all respect as specified and directed.

S&F coloured vitrified ceramic tiles 9-10 mm thick (square/ rectangular) glossy finish, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour complete all as specified and directed.

S&F coloured vitrified ceramic tiles 9-10 mm thick (square/ rectangular) glossy finish, area of each tilesnot exceeding 0.36 sqm in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour complete all as specified and directed.

S&F Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour complete all as specified and directed.

S&F Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour complete all as specified and directed.

M&L for pre polished granite (of any type) stone of 17-19mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone in flooring including necessary holes, cutting for wash hand basins or of similar type complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab flooring of size not less than 500X500mm over 20mm thick cement mortar (1:6) cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for 18-20mm thick machine cut kota stone slab of size not less than 500X500mm in riser of steps, skirting , dado and pillar over 15mm thick cement mortar (1:4) cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down cement plaster on brick/stone/concrete surface of ceiling/walls, etc. of any thickness including raking out joints, hacking for key, scrubbing down with water, etc of any description complete all as specified and directed.

M&L for 15mm thick plastering on brick/stone/concrete surafces of wall in cement sand mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick plastering on brick/stone/concrete surafces of wall in cement sand mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L 10mm thick plastering on brick/stone/concrete surafces of wall in CM (1:4) finished fair and even complete all as specified and directed.

M&L 10mm thick plastering on brick/stone/concrete surafces of ceiling in cement mortar (1:3) finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering/plastering over RCC roof in CM 1:3 fair faces of slab and finished even and smooth without using extra cement mixed with WPC @ 3% of the total weight of cement or as per manufacturer's instruction complete all as specified and directed. Note- WPC shall be measured and paid saperately under the relevant item.

Supply only water proofing compound cocomplete all as specified and directed. Make: (i) Dr. Fixit Pidilite Industries Ltd (ii) The Structural Water Proofing Co Pvt Ltd.

Taking down of shutter of any description exc 1 Sqm and n. exc 2 sqm and refixing in the same opening after necessary adjustments etc complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, fixed in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 35mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. Note-The measurement shall be carried out as in plain.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws complete all as specified and directed. Note-The measurement shall be carried out as in plain.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in eves covering or of similar type, fixed with self tapping screws including necessary mild steel flats and screws for fixing with framed structure complete all as specified and directed.

S&F in repair exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 605x605mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with 4mm dia GI wire as suspender and including 4mm thick decorative pre -painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type complete all as specified and directed. Make-Eternit, Everest or its equivalent)

Supply and laying APP based polymeric membrane minimum weighing 3Kg per Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on bitumen primed surface by burning torch application complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc to opening by screw and PVC sleeves complete all as specified and directed.

S&F anodised aluminium window and ventilator shutters,side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as aluminium peg stays 150mm long (1 no.). aluminium hinges (2 nos.) , aluminium handle (1 no.) complete all as specified and directed.

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,Aluminium handles 2 Nos in each door, aluminium hinges(100mm-3Nos),anodised aluminum snap beading screws etc complete all as specified and directed.

S&F 5.5mm sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 4mm sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of Exterior weather coat over 3mm thick wall care putty over a coat of exterior primer complete all as specified and directed.

M&L for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper finished with spunge roller over a coat of alkali resistant priming paint over 3mm thick (in two layers), wall care putty complete all as specified and directed.

M&L for preparation of new undecorated painted steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for Preparation of undecorated plastered or unplastered surface of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for Preparation of undecorated plastered or unplastered surface of wall and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new undecorated painted wooden surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for writing letters or figures (block roman, Italic or Indian) through synthetic enamel paint n exc. 30 cm high onto 12m height building over square or round base painting including necessary scaffolding arrangement complete all as specified and directed.

M&L for preparation of new undecorated wall surfaces and applying two coats of cement base paint over a coat of cement primer on external walls complete all as specified and directed.

M&L for preperation of new APP surface of any description not otherwise described, over 10cm width or girth and applying two coats of aluminium paint over it complete all as specified and directed.

M&L for applying evenly a tack coat of industrial bitumen of grade 85/25 at the rate of 1.2 Kg per Sqm including cleaning the surface complete all as specified and directed.

S &F aluminium anodised sliding door bolts with hasp and staple (bolt type) 12mm dia bolt 250mm long, with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F mortice lock in shutter, vertical type 100mm size 4 levers brass body of two keys complete all as specified and directed.

S&F 75mm size butt hinges medium weight, cold rolled mild steel (ISI marked) complete all as specified and directed.

Supply only 100mm size of butt hinges medium weight, cold rolled mild steel (ISI marked) complete all as specified and directed.

S&F Brass handle cast type polished bright 150 mm size (ISI marked) complete all as specified and directed.

S&F Aluminium handle cast type anodised 150 mm size (ISI marked) complete all as specified and directed.

S&F 20mm dia tubular towel rail 600mm long of cast copper alloy, chromium plated with end brackets complete in all respect as specified and directed.

S&F door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed to shutter (ISI marked) complete all as specified and directed.

S&F aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed (ISI marked) complete all as specified and directed.

S&F 20mm outer dia CPVC pipes SDR 11 & plain and brass threaded CPVC SDR 11 fittings on walls/ceiling or laying in floors with all necessary fittings of brass threaded and fixing chemical including necessary cutting chauging complete concealed in wall nature complete all as specified and directed.

S&F 20mm dia of gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron/CPVC pipe/fittings and fixed complete all as specified and directed.

S&F 15mm bore dia CP finish , bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/CPVC pipe/fittings or for brass ferrule including cup washer/flange complete all as specified and directed.

S & F 15mm bore dia CP finish,angle valve, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron/CPVC pipe/fittings or for brass ferrule including cup washer/flange complete all as specified and directed.

S & F vitreous china wash down water closet Pan (pedestal pattern) white including plastic water closet seat cover, white, closed pattern with flat bottom, and mild steel chromium plated hinging device (exclusive flushing cistern and flush pipe) complete all as specified and directed.

S & F PVC valveless, syphonic action type, low level, dual flush cistern, white, with inlet ball valve, float and handle including brackets & flush pipe of polyethylene complete all as specified and directed.

S & F wash hand basins, vitreous china of size 550 x400mm(flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron/CPVC pipe/fittings complete all as specified and directed.

S & F PVC (SWR) branch piece with access door in wall, single (single Tee) equal or unequal 110mm bore pipe jointed with rubber packing and fixing chemicals and necessary mild steel pipe clamps complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length jointed with rubber packing and fixing chemicals laid in trenches 110mm bore complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length jointed with rubber packing and fixing chemicals and necessary mild steel pipe clamps fixed to walls 110mm bore complete all as specified and directed.

S & F PVC (SWR) bends any radius 110mm bore with access door jointed with rubber packing and fixing chemicals complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laying in trenches 75mm bore complete all as specified and directed.

S & F PVC (SWR) bends any radius 75mm bore with access door complete all as specified and directed.

S & F PVC (SWR) branch piece with access door , single (single Tee) equal or unequal 75mm bore pipe complete all as specified and directed.

S & F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement floor trap complete all as specified and directed.

S & F PVC (SWR) 75mm bore vent cowl complete all as specified and directed.

S & F PVC (SWR)110mm bore vent cowl complete all as specified and directed.

S & F Rotational moulded polyethylene water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including two tank nipples one at inlet and other at one outlet of 20mm dia complete all as specified and directed.

S & F PTMT ball valve high pressure 20mm bore with epoxy coated aluminium rod & high density plastic ball screwed for iron/CPVC pipe/fittings complete all as specified and directed.

S&F chrome finished toilet paper holder of cast copper alloy complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixing with beads complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section and fixed 200mm size (ISI marked) complete all as specified and directed.

S&F 15mm bore dia CP finished concealed stop valve of long body , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron/CPVC pipe/fittings or for unions and fixed complete all as specified and directed.

S&F 15mm dia bore cast copper alloy, chromium plated shower roses with swivel joints including fixing to steel/CPVC pipe/fittings or of union complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F plastic seat cover for padestal water closet, white, closed pattern with flat bottom, and cover and mild steel chromium plated hinging device complete all as specified and directed.

S&F 15mm bore of tubes medium grade galvanised with all fittings fixed complete to walls and ceiling or laid in floors including necessary cutting, chasing etc complete all as specified and directed.

S&F 20mm bore of tubes medium grade galvanised with all fittings fixed complete to walls and ceiling or laid in floors including necessary cutting, chasing etc complete all as specified and directed.

M&L RCC Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC Type A-1 1:1.5:3 Mix Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc complete with effective depth of 1.5 meter and overall depth of 3 meter for 10 users capacity. Drg No TD/SZ/603 sheet No 1/1 to 1/10 complete all as specified and directed.

M&L Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in Type A-1 1:1.5:3 cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2m dia and 3.0m depth complete all as specified and directed.

S&F top hung steel ventilators with glazing bars, with box type hinges, steel handle, and steel peg stay dovetailed or welded complete all as specified and directed.

S&F Vitreous China urinals, full stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed.

E/M PORTION

M&L for river sand,granular sized, washed and screened dried completely free from harmful and organic matters for cushioning to under ground cable in tenches below and around under ground cable including spreading and levelling complete all as specified and directed.. Note:-Only punned thickness after specified compaction shall be considered for measurement and payment.

M&L for sub class 'B' bricks laid flat in trenches for the protection of under ground cable complete all as specified and in SSR Part-1

Supply, laying, jointing and testing LT cable in trenches or on poles / walls, XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core for laying in trenches and poles /walls complete all as specified and directed.

S&F GI Pipe light grade 40 mm dia, ISI marked, of required length for protection of cables in wall /pole /under road complete including necessary MS clamps, nuts, bolts and washers etc; all as specified.

S&F GI Pipe Medium grade 25 mm dia, ISI marked, complete with all fittings fixed complete to walls , ceilings ,floors laid in trenches complete all as specified and directed.

S&F Gun metal Gate Valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25mm ISI Marked,complete with all fitting accessories complete as specified and directed.

Cutting and insertion of Tee/ ferrule for taking branch connection complete all as specified and directed.

S&F 25mm bore brass valves,high pressure with polythene float and flynut screwed for iron pipes or brass ferrule complete all as specified and directed.

Taking down carefully aluminium / copper point wiring for one light , fan, socket power point or buzzer controlled by one switch complete including fitting / fixtures such as switches, ceiling roses, holder, socket, light fitting etc; and making good disturbed surfaces of walls, ceilings etc complete all as specified and directed.

M/S Barua Enterprise

M/S Inder SINGH SABARWALL