Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹5.1 LAccepted-AOC | L1 | Accepted-AOC lowest bidder | |
| 2 | L2₹5.3 L+₹21,125.14 (4.17%)Rejected-AOC | L2 | Rejected-AOC First lowest bidder |
| Sl No | Description | Qty | Unit | A M YOOSAF L1 | FAHAD A Y L2 |
|---|---|---|---|---|---|
| 1.00building maintanance | |||||
| 1.00 | 10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes | 724.52 | kg | 194.27 ₹1,40,752.5 Lowest | 210 ₹1,52,149.2 |
| 1.00 | OD367378/2025-2026:Providing and fixing on Eave face UPVC Half cut Rain water gutter pipes (150mm 4kg/cm2) with all necessary fittings with clamps at 1 M intervel (12.41.2 modified) | 65.8 | metre | 508.76 ₹33,476.41 Lowest | 550 ₹36,190 |
| 1.00 | OD367383/2025-2026: Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) 0.35 mm (+0.05%), total coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side. of the sheet and polyester top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratchesduring transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws ofsize (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trusses and including cutting tosize and shape wherever required. | 221.26 | sqm | 621 ₹1,37,402.46 Lowest | 630 ₹1,39,393.8 |
| 1.00 | OD368809/2025-2026:Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of 6mm aggregate , filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. Modified data of 16.68 | 95 | sqm | 1,177.47 ₹1,11,859.65 Lowest | 1,200 ₹1,14,000 |
| 1.00 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | 1.36 | cum | 9,235.97 ₹12,579.39 Lowest | 9,360 ₹12,748.32 |
| 1.01 | 21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):
For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) | 1.94 | kg | 584.72 ₹1,132.02 | 550 ₹1,064.8 Lowest |
| 1.01 | 21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | 4.02 | sqm | 1,278.82 ₹5,138.3 Lowest | 1,350 ₹5,424.3 |
| 1.01 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil | 4.39 | cum | 359.72 ₹1,579.89 Lowest | 380 ₹1,668.96 |
| 1.01 | OD368931/2025-2026:DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good
quality blasted rubble including packing to compactness to lines and levels cost and conveyance
of all materials labour charges etc. complete as per direction of Departmental officers at site | 4.39 | cum | 3,993.46 ₹17,539.28 Lowest | 4,200 ₹18,446.4 |
Tender Value
₹5.1 L
EMD Value
₹12,654
Closing Date
4 Nov 2025, 6:00 pmClosed
ASSISTANT ENGINEER LID EW
ASSISTANT ENGINEER LID EW
anganwadi aintnance
2025_LSGD_816216_1
26/AE/LIDEW/EMPTY/2025-26
Open Tender
Civil Works - Buildings
Item Rate
180 days
ERUMAPETTY
Please refer Tender documents.
5 documents required · 5 mandatory
₹1,120
Yes
₹12,654
Yes
25 Nov 2025
28 Oct 2025
5 Nov 2025
28 Oct 2025
4 Nov 2025
28 Oct 2025
stage.html
html • 0.04 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_1366983.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.04 MB
BOQ_1366983.xls
BOQ • 0.31 MB
viewsbdthrikk.pdf
Tender Documents • 1.83 MB
epayment.pdf
Tender Documents • 0.11 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .