Devlopment of cattle shed at khaswadi, North zone for vadodara Municipal Coporation.

Name of Work: NEW CONSTRUCTION WORK OF CATTEL SHEAD AT KHASWADI FOR VADODARA MUNICIPAL CORPORATION

No. Description Quantity Unit Rate Amount

Demolition of Brick work and stone masonry including stacking of serviceable materilas

1 and disposal of unserviceable materials with all lead and lift.(ii) In Cement Mortar. 3.1 Cumt. 564.16 ₹

Dismentaling of sheet roofing including ridges, Hips, Valleys, Gutters etc. stacking of

serviceable materilas and disposal of unserviceable materials with all lead and lift.(i)

2 G.I.sheet roofing. 14.62 Cumt. 48.91 ₹

Dismentling wood work, wrought framed and fixed in frames trusses including stacking the

3 materials with all lead and lift. 3.71 Cumt. 1803.36 ₹

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful

4 materials and disposing off the excavated stuff upto 3.00 km. lead. (B) Dense or Hard soil 640.435 Cum 153.41 ₹

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking

of useful materials and disposing off the excavated stuff upto 3.00 km. lead. (B) Dense or

5 Hard soil 364.3 Cum 166.44 ₹

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- hand broken

stone aggregates 40 mmnominal size) and curing complete excluding cost of formwork in

6 (A) Foundation and Plinth 201.69098 Cu.m 3080.9 ₹

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

7 as per latest IS 456 shall bemaintained) (Cement level 450 kg ) (A) Foundations. 193.9618175 Cu.m 4896.32 ₹

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of

8 Columns etc. and Mass concrete. 294.006 Sqmt 179.36 ₹

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (B) Flat surfaces such as soffits of

suspended floor roof slabs Landings and the like. (2) Floors etc. above 200mm in

9 thickness.( grade slab) 17.758 Sqmt 282.08 ₹

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (G) Columns PillarsPosts and struts. (1)

10 Square Rectangular Polygonal in plan. 155.08 Sqmt 313.06 ₹

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (H) (1) Sides and soffits of Beams Beam

Haunchings cantilevers Girders Bressumers and Lintels not exceeding 1 M. in Depth.

11 (Ground Beam) 166.5632 Sqmt 202.18 ₹

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (M) Staircase with sloping or stepped

12 soffits including risers and stringers excluding landing 80.0392 Sqmt 254.36 ₹

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (H) (1) Sides and soffits of Beams Beam

Haunchings cantilevers Girders Bressumers and Lintels not exceeding 1 M. in Depth. ( Lintel

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ

reinforced concrete and plain concrete work in. (B) Flat surfaces such as soffits of

suspended floor roof slabs Landings and the like. (2) Floors etc. above 200mm in thickness.

Brick work using common burnt clay building bricks having crushing strength not less than

35 kg./Sq.Cm. in foundation and plinth in CementMortar 1:5. (1- Cement : 5 -fine sand) (B)

15 Conventional 154.375862 Cu.m 4153.07 ₹

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations

etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by

16 ramming and watering. 743.057258 Cu.m 133.65 ₹

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone

aggregates 20 mm nominal size) and curing complete excluding cost of formwork in (A)

17 Foundation and Plinth 12.05 Cu.m 3656.13 ₹

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

as per latest IS 456 shall bemaintained) (Cement level 450 kg) C) Grid Slab upto floor two

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

as per latest IS 456 shall bemaintained) (Cement level 450 kg) D) Column upto floor two

Structural steel work ( Confirming to IS 4923-1997) riveted, bolted or welded in builtup for

all type sections, in framed work, including cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer all complete as per the structural designs and

20 directions of Engineer in charge.Column ( 122 x 61 x 3.6mm 3643.2 Kg 131.15 ₹

Steel work, riveted in built up sections framed work including cutting, hoisting, fixing in

position and applying a priming coat of red lead paint. (A) In beams and joists, channels

angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip

21 and jack rafters, purlins conneted to common rafters and the like. 128.21 Q 5889.5 ₹

Providing corrugated G.I. sheet of class-3 roofing fixed with

glavanished iron J or L Hooks, Bolts and nuts 8mm diameter with bitumen and G.I. limpet

washer or G.I. limpet washer. filled with white lead complete excluding the cost of purlins,

22 Rafters and Trusses.(1) 0.80 mm thick sheet. 411.6 Sqmt. 727.13 ₹

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and

23 placing in position complete upto floor two level 47941.15305 Kg 77.29 ₹

20mm thick Sandfaced cement plaster on walls consisting of 12mm thk backing coat of

C.M.1:3 (1 cement :3 sand) & 8mm thk finishing coat of CM(1:1)1 cement :1 sand at all

24 levels etc complete as directed by EIC. 2178.7184 Sqmt. 337.52 ₹

Providing & Fixing the G.I. welded wiremesh - 27 guage(Crimp Jali) of approved size

applying between the RCC and masonry junction in proper line, level and plumb with all

material, labour, tools, tackles and equipment. Including providing and fixing the jali with

25 nails, etc complete as directed by the site-in-charge. 1416.4 Sqmt. 184.02 ₹

Finishing wall with weather proof exterior emulsion paint (with 7yrs. warranty period) on

plastered surface (two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt and remains of loose powdered materiels etc

26 complete at all floors and all levels as directed by EIC. 2191.752 Sqmt. 117.4 ₹

Applying two coats of Birla or Asian acrylic lappy (putty) and two coats of primer of

approved brand and manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and other foreign matter and

27 sand prepared smooth etc complete at all floors and all levels as directed by EIC. 1754.706 Sqmt. 40.59 ₹

Wall painting (3 coats) with plastic emulsion paint of approved brand and manufacture on

undecorated wall surface to give an even shade including throughly brushing the surface

free from mortar dropping and other foreign matter and sand papered smooth etc

28 complete at all floors and all levels as directed by EIC. . 1754.706 Sqmt. 115.43 ₹

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

as per latest IS 456 shall bemaintained) (Cement level 450 kg) C) Ground Beam / Plinth

29 Beam upto floor two level. 25.093668 Cumt. 4896.32 ₹

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

30 as per latest IS 456 shall bemaintained) (Cement level 450 kg) C.) Lintel 2.568226 Cmt. 4896.32 ₹

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

31 as per latest IS 456 shall bemaintained) (Cement level 450 kg) C) Slab upto floor two level. 148.05464 Cumt. 4896.32 ₹

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

as per latest IS 456 shall bemaintained) (Cement level 450 kg) C.) Beam upto floor two

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering upto floor two level and

33 finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand) 622.954 Sqmt. 192.41 ₹

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of

cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse

sand) laid over and jointed with grey cement slurry mixed with pigment to match the

34 shade of slab including rubbing and polishing etc. complete. (A) 25mm thick 219.53 Cmt. 1001.14 ₹

Provoding and fixing flush door shutters, solid core construction with frame of first class

hardwood with cross band and face veneer or plywood face panels,laminate,Batten patti

including anodised alluminium butt hinges eith necessary screws. (B) Non-decorative type

and block board core anodised alluminium butt hinges in flush door shutters. (2) 35 mm

Providing and fixing window having extruded aluminum colour Powder coated section

frame main outer size 63.50 x 38.10x 1.95mm (of Jindal section no. 4605@ Wt.

Kg/Rmt), horizontal two track member size 61.85mm x 31.75mm x 1.20mm (of Jindal

section no. 8687, @ Wt. 0.695 Kg/mt),vertical member of size 61.85mm x31.75mm x

1.30mm (of Jindal section no. 8758 @ Wt. 0.659 Kg/mt) with sliding shutters of horizontal

member size 40mm x 18mm x 1.29mm (of Jindal Section No. 8949 @ Wt. of 0.456 Kg/mt),

vertical member of size 40mm x 18mm x 1.29 mm (of Jindal section no: 8947 @ Wt. of

0.456 kg / mt / section 8948, @ Wt. 0.457 kg/mt) with 5 mm th transparent bronze colour

tinted float glass with powder coated aluminum fittings and fixtures and transparent

36 silicon sealant glass fixing to frame as per details etc. 4.75 Sqmt. 1713.7 ₹

Providing and laying Ceramic tiles 6mm thick in skrting risers of steps and dedo on 10mm

37 thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry 15.48 Sq.Mt 1022.34 ₹

Providing and fixing FRP frame size 100x50 mm and 28mm thick FRP depress panel shutter

having extra reinforcement on sides & edges in Gel coat finish. The core of the shutter &

frame is to be filed up withinjected fire retardant grade polyurethene foam done in situ

alongwith embedded wooden pieces for stiffening & also taking hinges & fintures.The

whole FRP frame & shutter is to be water proof weather proof, termite proof & resistance

to mild acid/alkali. Rates are to be inclusiveof S.S hinges with necessary screws &

38 alluminium fixtures & fastenings& fastener sleeve. 2.31 Sq.Mt 2377.76 ₹

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden

39 plugs with C.P. brass scews.(B) 600mm x 20mm size. 2 Each 616.42 ₹

Supplying and fixing heavy quality fittings with best quality with necessary brass screws,

nails etc. complete as directed and as approved by Architect & Engineer-in¬charge. The

40 fixture & fastenings shall be provided as under : 1) Bevelled edge mirror 600mm x 450mm 1 Each 233.67 ₹

Providing and fixing wash down water closet (European type, W.C. Pan) with integral P or S

trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine

sand) (Seal and cover to be measured and paid for separately) (A) vitreous China Pattern

41 :(i) in white colour 3 Each 1303.71 ₹

Providing and fixing Urinal or approved quality including connecting the Urinal with waste

pipe , tap etc. complete.(A) White earthenware flat back or corner type size 430mm x

Providing and fixing washbasin with single hole for pillar tap with M.S. brackets painted

white including setting holes and making good the same and including all fittings.(A)

Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

including providing and fixing C.P. brass waste for washbasin. (B) 40mm dia., including

43 providing and fixing M.I. fisher union for washbasin. (B) 40mm dia. etc. complete 5 Each 1597.03 ₹

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jail of

the following nominal diameter of self cleansing design with C.I screed down or hinged

44 grating including the cost of cutting and making good the walls. 5 Each 585.37 ₹

Providing and fixing pillar tap, capstan head, screw down high pressure with screws,

45 shanks and back nuts. (i) 15mm dia. 7 Each 308.73 ₹

46 Providing and fixing brass screw down stop tap. (A) 15mm dia. 4 Each 205.83 ₹

Providing and fixing chromium plated brass half trun flush cock of approved quality

47 including fixing in pipe line etc. complete. (ii) 25mm dia. 5 Each 263.77 ₹

Providing and fixing screw down bib taps of following size. (A) Brass screw down bib

48 tap polished bright. (i) 15mm dia. 3 Each 186.83 ₹

Providing and fixing cast iron (Spun) Nahni trap of the following nominal diameter of self

cleaning design with C.I. screaed down or higned grating including cost of cutting and

49 making good the walls and floor 100mm inlet and 50mm outlet. (C) 100mm dia. 6 Each 632.64 ₹

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight

C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square

50 mouth traps. (A) 100mm x 100mm size P type. (upto 10 ton) 6 Each 1292.19 ₹

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc.

51 complete.[A] 40 mm. 600 Rmt 447.72 ₹

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc.

52 complete.[C] 25 mm. 350 Rmt 253.82 ₹

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc.

53 complete. [A] 15 mm. 500 Rmt 170.36 ₹

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B)

conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring,

& fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line,

pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using

of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every

mm center to center or shall be concealed in walls as directed including necessary fittings

such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive

54 solvent cement including cost of all materials. 300 Rmt 856.03 ₹

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded

stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse

sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-

Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels

in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal

size) finished smooth complete including curing and festing (i) Inside size 900mm x

1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight

of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame

Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not

less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type depth

55 0.90 Metre for 150mm diameter sewer. 5 Each 11042.74 ₹

Providing erecting and fixing double coated Syntex PVC. (ISI) water tank of required

56 capacity each with all necessary fittings and connection etc. complete on terrace. 30000 Litre 3.95 ₹

Supplying and fixing reinforced concrete heavy duty non-pressurepipes with collars for

culverts carrying heavy traffic as per IS 458-1991specifications including setting the pipes in

C.M. 1:2 watering andlaying (to level or slopes) of class NP3 of following

57 internaldaimeters.(i) 300mm dia. 50 Rmt 659.99 ₹

Providing, laying and jointing in true line and level 110 diametreU.P.V.C (Type B)

conforming to IS 13592-1992 with one end plainand other end socketed with rubber ring,

& fittings conforming to ISI14735-1999 of approved make for drainage system pipe line,

pipeshall be jointed with each other with rubber lubricant, pipe shall befixed on wall using

of PVC clamp of the size 110 mm diametre x 149mm length x 145 mm heigh at every

mm center to center or shallbe concealed in walls as directed including necessary fittings

such asbends, shoes etc. including testing of pipes and joints and jointed withadhesive

58 solvent cement including cost of all materials. 200 Rmt 856.03 ₹

59 Providing and fixing Slotted cowl (terminal guard ) 75 mm dia 4 Each 217.15 ₹

Preparing structural design of RCC Under Ground / Partially underground / above high

ground level Reservoir of required capacity as per relevant I.S. standards and constructing

the same, including excavation in all types of soil strata (including rock) including shoring

strutting if required, for loose soil / to protect from collapse, casting 100 mm thick P.C.C.

levelling course in M-15, Refilling the pit with proper soil and disposing of the surplus stuff

at all lead. Including cement plaster in CM 1:2 with approved water proofing compound to

all over inside container (i.e. walls, base, top slab/dome bottom etc. all). Including all types

of labour and material charges of lowering, laying, erecting / hosting and jointing of pipe

assembly to inlet, outlet overflow, washout and bye pass arrangement as per hydraulic

design. Providing and fixing accessories, CI Manhole frame and cover, water level

indicator, adequate cowl type ventilators or lantern type ventilator with stainless steel jail.

RCC chambers for valves. Providing and applying three coats of cement paint / snowcem to

the out side face of structure. It also includes satisfactory water tightness test as per

relevant I.S. code and painting name of scheme and capacity on the tank as per direction

of engineer in charge.List of Indian Standards for Design of GSR / SUMP: -The structural

design of GSR shall be in accordance with provisions relevant I.S standards.(1) I.S.

part I & II 2009 or Its latest revision(1.1) I.S. 3370 part III & IV 1965 or Its latest revision(2)

I.S. 456 – 2000 or Its latest revision.(3) I.S. 1893 – 2000 – 1984 or Its latest revision.(4) I.S.

875, Part – 1 to 3, 1987 or Its latest revision.General Specifications: -(1) Water depth in

container shall be adopted as per data of tender. Capacity shall be calculated excluding

free board of the reservoir. If water depth is not specified, the suitable water depth /

acceptable to field engineer in accordance with hydraulic requirement.(2) Shape of

container (in plan) specified by in data shall be adopted in absence circular shape shall be

adopted.(3) Size shall be fixed as per availability of space (land area) at site / acceptable

engineer in charge.(4) Effect of overlapping of pressure bulbs on soil due nearby structure

and proposed sump should be considered.(5) Care shall be taken that no damage should

occur to nearby existing structure. Compensation shall be paid for the same by agency.(6)

60 The minimum concrete grade for RCC shall be M-30.(7) HYSD Fe 415 / 500 grade 20000 Litre 5.49 ₹

Box cutting the road surface to proper slope and camber for making a base for road work

including removing the excavated stuff and depositing on the road side slope as directed

61 upto 50Mt.lead. 52.35 Cumt 106.81 ₹

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

62 as per latest IS 456 shall bemaintained) (Cement level 450 kg ) 49.14 Cumt 5093.12 ₹

63 Supplying and filling premolded bituminous joint filler. 12 mm Thick. 0.28 Cumt 553.79 ₹

Providing, laying and fixing of 80mm thick(M 45 grade) RUBBER MOULDED interlocking

coloured paver block as per design given by Engineer Incharge with 75mm thick sand bed

layer, watering, compacting, paving. with compact by mechanical compacter etc. complete

64 as per specification 195.78 cu.m 788.81 ₹

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block

30cm length,30cm height and 15cm thick of M250 grade concret as per approved design

and including excavation for fixing in proper line and level,filling the joint with C:M 1:3

65 (1cement:3fine sand) etc complete. 132 cu.m 370.68 ₹

Drilling of 300 / 315 mm dia. bore in over burden strata including lowering of 204 mm dia

UPVC / 225 / 250 mm dia. PVC / MS ERW casing pipes up to required depth and further

drilling of 200 mm dia. bore hole in all types of Rocky Strata, soft rock & hard rock strata

formation by DTH rig including flushing of bore hole by air compressor and measuring of

66 yield of bore by V notch and fixing of borecap etc.complete. (Oer burden up to 12 mtr.) 285 Metre 549.44 ₹

67 Providing & fitting bore cap / plug suitable to 250 mm Ø pipe. 1 Each 1161.62 ₹

Geohydrological ground water investigation

68 including vehicle charges. 1 Job 14428.86 ₹

69 Chemical analysis charges of water sample. 1 Job 606 ₹

Supply of three phase submersible pump set as per rate contract specifications of GWSSB.

70 Category 7, Discharge 510 LPM @ 52 meters head with 12.50 HP. 1 Set 28029.52 ₹

71 Providing and laying 75 mm HDPE pipe 10 kg/Sqcm 300 Meter 179.78 ₹

72 MS clamps suitable for 75 mm Ø HDPE pipe. 1 Pair 574.79 ₹

Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and getting out the soil and

disposal of the surplus excavated soil as directed within a lead of 50 Meter for following

73 diameter of pipes.(iii) 300 mm 66.66666667 Each 1561.19 ₹

Precast concrete block masonry (including quoin blocks jamb blocks closer etc.) with solid

concrete blocks of approved size made of cement concrete 1:3:6 mix (1- Cement : 3 coarse

sand: 6- graded stone aggregates of 20 mm and down grade) in foundation and plinth

74 cement morter 1:6 96.144 Cumt. 3726.43 ₹

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in

position and applying a priming coat of red lead paint. (A)In beams and joists, channels

angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip

75 and jack rafters, purlins conneted to common rafters and the like 3.15 Q 9108.48 ₹

Painting two coats (excluding priming coat) on new steel and other metal surface with

synthetic enamel paint, brushing to give an even shade including cleaning the surface of all

76 dirt, dust and other foreign matter. 18 Sqmt. 66.94 ₹

Prime Coat : Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and other foreign

matter and scoured with brushes fine steel wood, scrapers and sand paper with ready

77 mixed priming paint brushing red lead. (SOR P.160 It No.1/19001/19.2) =21.80/- 18 Sqmt. 35.88 ₹

Carrying out plinth treatment to post construction / existing structure by spraying chemical

solution for termite control treatment including labour and material consistent with I.S.I

78 specification. (Plinth Area will be measured for payment purpose) 720.36 Sqmt. 96.4 ₹

Providing and laying controlled cement concrete M.200 and curing complete excluding the

cost of formwork and reinforcement for reinforced concrete work in (E) Staircases

79 excluding landing upto floor two level 6.95694 Sqmt. 5453.2 ₹

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement

conctere work , using cement content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in transit mixer for a lead up to

10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying and the cost of centering shuttering finishing excluding reinforcement

including cost ofadmixtures in recommended proportions as per IS: 9103 to

accelerate/retard setting of concrete, improve workability without impairingstrength and

durability as per direction of the Engineer - in - charge.Without Fly Ash (Min cement level

as per latest IS 456 shall bemaintained) (Cement level 450 kg) C.) Beam upto floor two

Half brick masonry in common brunt clay building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement : 4 -coarse sand ) in foundation and

81 plinth (A) Modular 24.295 Sqmt. 605.29 ₹

Providing and laying Ceramic tiles 6mm thick in skrting risers of steps and dedo on 10mm

82 thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry 8.1516 Sqmt. 970.17 ₹

Providing and laying Vitrified tiles 8 to 10 mm thick , in skrting risers of steps and dedo on

10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement

Providing and laying broken chine mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed tiles to belaid over cement mortar

1:3 to plain or slope and to be tempered tobring mortar creme out upto surface using

white cementincluding rounding off junctions and extending them upto 15 cm along the

84 wall,clearing with water and oxalic acid etc. as directed. 96.4217 Sqmt. 765.97 ₹

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior

plastering upto floor two level and finished even and smooth in (iii) Cement mortar 1:6 (1-

cement:6-sand)Extra over items 58 to 71 for plastering on ceilings and sofits of stairs upto

85 floor two level instead of plastering on walls. 49.757104 Sqmt. 145.12 ₹

Clearing and grubbing road land including uprooting rank

vegetation grass bushes,shrubs,sapling and trees girth up to

300 mm removal of stumps of trees cut earlier and disposal of

unserviceable materials(A) By manual means in area of light

86 jungle 0.1197239 Hectare 84495.12 ₹

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length , in below type of pipe erected with 6A Modular type switch /

bell push & accessories and earth continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

1 textured/metallic/white front plate modules erected on / in wall / ceiling as per 100 nos

pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete. cat III.

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires, in below type of pipe to be erected complete with earth continuity

and necessary connection with primary light with accessories erected on Metal /

PVC / wooden box covered with 3 mm thick PC(Polycarbonate) / Acrylic sheet for

2 open / concealed wiring. with necessary Lamp holder / ceiling rose / 18 nos

H.D.Connector as directed.

Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for

Secondary Point.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete.

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are

of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in

below type of pipe erected with 6A Modular type switch and hum free EME four

or more step type electronic fan regulator with separately mounted and accessories

3 with earth continuity of following type erected on PVC / Metallic/Wooden box, 40 nos

single mounting base frame covered with textured/metallic front plate modules

erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete. cat III.

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules erected on / in wall /

ceiling with following type accessories. cat III. 241.39 ₹

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete with Modular type switch &

pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe erected with following type

of accessories. [I] For 6A Plug with 2-1.5 sq.mm Cu. Wire.(f) with medium class

Rigid PVC pipe and accessories erected concealed in wall/ceiling complete. cat

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in below

type of pipe erected complete with Modular type switch & 5 pin Plug erected on

6 PVC / Metallic/Wooden box covered with appropriate front plate modules erected 6 nos

on / in wall / ceiling as per pipe erected with following type of accessories. [II] For

16A Plug with 2-2.5 sq.mm Cu. Wire. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete. cat III.

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in below

type of pipe erected complete with Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with appropriate front plate modules erected

on / in wall / ceiling as per pipe erected with following type of accessories. [III]

For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green)

earthing wire from mcb d b board.. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete. cat III.

Providing & erecting Switch board for Computer or electric apparatus consisting

of following modular type accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with necessary connections

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug . For Modular Type Accessories. Cat III.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

9 Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, 200 mtrs.

in approved manner as directed.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

10 Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, 50 mtrs.

in approved manner as directed.

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of

coupling, PVC bushes, Check-nuts etc. complete of following sizes. (2) 25 mm.

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of

coupling, PVC bushes, Check-nuts etc. complete of following sizes. (3) 32 mm.

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on

13 wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire 400 mtrs.

of green colour for earth continuity of following size (a) with medium class Rigid

PVC pipe and accessories (a) 2 wire 1.5 sq. mm.

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on

14 wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire 300 mtrs.

of green colour for earth continuity of following size (a) with medium class Rigid

PVC pipe and accessories (b) 2 wire 2.5 sq. mm.

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with

15 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for 100 mtrs.

earth continuity of following size (A) with medium class Rigid PVC pipe and

accessories (a) 2 wire 4 sq. mm.

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with

16 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for 250 mtrs.

earth continuity of following size. (a) with medium class Rigid PVC pipe and

accessories. (h) 4 wire 6 sq. mm. (Main Panel to LDB , PDB.)

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star

rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite magnet

Motor, class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos. canopies,

shackle kit with earthing provision, copper winding, Power factor not < 0.9,

Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM,

17 RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with remote unit for Speed 45 nos.

Control and all remaining accessories including safety pin, nut bolts, washers,

temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage and rectifier

circuit with surge, over current and overload protection , 50 Hz, Single phase AC

Supply, earthing etc. Complete as required. [ Make shall be approved by Engineer

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down

18 rod erected duly painted for fan complete with proper insulation without leckage 45 mtrs.

and earthing. 108.07 ₹

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC

bars up to 50mm length each side and pierced through a 16 Gauge M.S. box /

Heavy Duty PVC box complete erected concealed in Ceiling with necessary

finishing. 108.07 ₹

Supplying & erecting approved make low noise decorative exhaust fan having

20 square frame ABS body with inbuilt lowers & square frame. 200mm with 1350RPM 15 nos.

21 Decorative call bell Ting-tong box type 250 volts complete erected. 1 nos. 68.68 ₹

Providing & erecting 240 V MCB double pole switch for motor & inductive load

(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

having following capacity. - use for AC control.

(A) 6 to 32 Amp. cat III. 299.97 ₹

Sheets steel powder coated enclosure suitable for incorporating One/Two nos.

MCB. - use for AC control. 176.75 ₹

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve)

having 10KA breaking capacity & confirms to IS :8828 in existing box having

following capacity - use for 3 phase machines.

(a) 6 to 32 Amp. cat III. 595.9 ₹

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to

25 operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in 40 nos.

existing box. confirming to IS 8828/1996 with ISI Mark cat III.

Providing & erecting 240 V MCB double pole switch for motor & inductive load

(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

having following capacity

(A) 6 to 32 Amp. cat III. 299.97 ₹

Providing & erecting 240 V MCB double pole switch for motor & inductive load

27 (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box 3 nos.

having following capacity. (B) 40 Amp. cat III. 330.27 ₹

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on

single phase 240 V. having characteristic of quick action & tripping with all advance

feature & do not incorporate any electronic component. for following Max. rating

erected as directed.

(i) 25 Amps.DP. cat III. 1969.5 ₹

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on

single phase 240 V. having characteristic of quick action & tripping with all advance

feature & do not incorporate any electronic component. for following Max. rating

erected as directed.

(ii) 40Amps. DP . cat III. 2235.13 ₹

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on

30 single phase 240 V. having characteristic of quick action & tripping with all advance 1 nos.

feature & do not incorporate any electronic component. for following Max. rating

erected as directed. (iii) 63 Amps. DP. cat III.

Providing and erecting Approved make RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for

31 operation on 3 phase and neutral 415V,50Hz. having characteristic of quick action 3 nos.

& tripping with all advance feature & do not incorporate any electronic component

for following Max. rating erected as directed. (ii) 40Amps. FP. cat III.

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve)

having 10KA breaking capacity & confirms to IS :8828 in existing box having

32 following capacity 1 nos.

(a) 6 to 32 Amp

Cat.III . 578.73 ₹

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve)

33 having 10KA breaking capacity & confirms to IS :8828 in existing box having 1 nos.

following capacity (c)63 Amp. cat III. 737.3 ₹

34 Half / One Module Blanking Plate of Standerd Size. 30 nos. 9.09 ₹

Providing and erecting Sheet Steel powder coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms

to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase outgoing. (b) sheet steel

double door (IP-43) (iii) 8 way.

Providing and erecting Sheet Steel powder coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms

to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase outgoing. (b) sheet steel

double door (IP-43) . (iv) 12 way .

Providing and erecting Sheet Steel powder coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms

to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to be used) suitable for

(B) three phase incoming and single phase horizontal type outgoing Per phase

isolation type (PPI). (b) sheet steel double door. (ii)6 way.

Providing & erecting weather proof, dust & vermin proof, floor mounted front

operated indoor type cubical panel board having necessary IP-42 protection &

above as per requirements made from 14 SWG thick CRC M.S. sheet for outer body

& doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary

supporting angles, flats including cutting, bending, drilling, welding, riveting with

internal partitions & cable alley as per requirements & instruction of engineer-in-

charge with erection of supplied switch gears, BUSBARS, with suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib,

bakelite control fuses for measuring instruments, earth bus & earth bolts,

38 foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with 2 mtrs.

locking arrangement and rubber gasket, heavy duty end terminal connections

complete. The Panel shall be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding

base beams) The panel shall be supplied with following approved manufacturers

with following size.

(B) The standard companies switch gear shall be used and only manufacturers at

CPRI approved factory

(i) with 350 mm depth .

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required.

(b) One wire 1.50 sq. mm. 16.16 ₹

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (d) One wire

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (e) One wire 6.00 sq.

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (f) One wire

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (g) One wire 16.00 sq.

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (h) One wire

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

45 existing pipe of following size (Specifically for control panel, relays, power 12 mtrs.

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (i) One wire 35.00 sq. mm .

Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

46 existing pipe of following size (Specifically for control panel, relays, power 6 mtrs.

switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required. (j) One wire 50.00 sq. mm.

Approved make Earth fault Relay suitable to mount with inter connection to

moulded case circuit breaker having CT ratio & MCCB rating as following along

47 with shunt trip 220V AC. with all internal connections & complete erected in 2 nos.

existing M.S.housing.

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper

Busbars with four equal Nos. of electrolyte bus having current density not more

than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with

48 colour insulating tape for phase sequence of following current carrying capacity, 4 mtrs.

erected with necessary bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary connections.

(B) Suitable for 200 Amp. capacity .

Supplying and erecting approved make panel mounting type Digital Voltmeter

49 having 3 digits LED display, 0 to 750 AC Volts range erected on existing panel 3 nos.

board with all connection, wiring etc .with manufacturers calibration certificate.

Supplying and erecting approved make panel mounting type Digital Ammeter

having 3 digits LED display, external CT operated, calibrated for 0 to 1000 Amps

suitable to operate on 500 Volt AC , erected on existing panel board with all

connection, wiring etc .with manufacturers calibration certificate.

Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC

Supply 500 V on existing panel board with necessary connections. 317.14 ₹

Supplying and erecting approved make suitable panel indicator LED type lamp,

lens cover, complete erected with necessary connections. 43.43 ₹

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up

53 to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C. 4 nos.

supply 50 c/s. with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA. at 415 V. having normal current rating

54 125A. with Fixed thermal & magnetic release suitable to work on A.C.supply 50 1 nos.

c/s. with all internal connections, spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only Cat III

providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and

55 having breaking capacity 10 KA to be erected in existing box. confirming to IS 30 nos.

8828/1996 with ISI Mark CAT-III 270.68 ₹

Providing & Erecting Chemical Earthing with 3mtr. Long earth electrode for the

switching box as per the technical specification given in the tender document.

57 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 50 kg. 794.87 ₹

Providing and erecting required size HOT deep Galvanised iron strip for earthing

of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.

Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/

Transformer, LT panel board, Motors etc. using copper clamp.

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables. (D) 3 1/2 core 70 Sq. mm ( 35 Sq.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing

trench / pipe at road crossing or floor of following size of cables. (C) 4 core 6 Sq.

mm Cu. Conductor YWY cable. (Main feeder Panel to PDB / LIFT.).

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid

Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of following size of cables. (A)

core 2.5 Sq. mm . (Main feeder Panel to Streetlight fixtures .).

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV

grade to be erected as directed of following size. (J) 4 core 2.5 Sq. mm.

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade

ISI marked copper wires of following size to be erected as directed. (e) 1.50 Sq.mm

core round PVC sheathed. - streetlight pole box to fixture & from DB MCB to

bollard lights. 44.44 ₹

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for

PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables. (C) 3 & 1/2 core 70 Sq. mm . (Main cable from

transformer to meter panel. ). 103.02 ₹

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for

66 PVC insulated armoured cable complete with out going tails, insulating tape etc for 12 nos.

following size of cables. (B) 2 to 4 core 6 Sq. mm. (Main feeder Panel to LDB, PDB.).

Solder less crimping type Copper lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (A)

1.5/2.5 to 6 Sq.mm. (Main feeder Panel to LDB, PDB.).

Solderless crimping type Copper lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (B)

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (E)

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of

70 same material at required depth for laying of cable. below ground /road surface for 600 mtrs.

enclosing cable and back filling the same to make ground as per original.(A)50 mm

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD

71 < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 30 nos.

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage capacity between the

ranges shown.). (B) Flood Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection. (iii) Above 60 to

watts. Cat-lll.

Providing street light pole bracket consisting of Light Class MS.pipe of 4.2 cms.

outside dia. complete with suitable M.S. sleeve tubing of approximate 45 cms. and

length suitable for 76.5 mm / 80mm. / require size pole top having sufficient

fastners for fixing the brackets and having spread of 1 mtr. length with suitable rise

as per site condition & suitable welded stiffener reducer and nipple with check nut

complete painted with one coat of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

[A] Single Arm bracket 1 Mtr.

Supplying and erecting approved make Octagonal pole made from HR sheet steel.

The pole should be made as per IS. and shall be coated with hot dip galvanizing as

per IS 2629/2633/4759, suitable suspend local wind speed with integral Junction

box consist of terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement

for cable termination to be erected With Suitable foundation (Included) as per

details given by manufacturer considering site requirement.

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm long J-Bolt.Approx

Pole weight 59 kg.

Supplying and erecting B class Galvanized iron pipe having smooth finished bore

of the pipe on both ends erected nuts and bolts along the pole / wall shaping the

pipe as per site requirement. Pipe dia as following.

Supplying & erecting approved make IP 55 grade Company fabricated Timer Panel

of following capacity for switch On-Off street lights on time scheduling basis made

from 16G CRCA sheet duly epoxy power painted inside and outside with hinged

75 doors and locking arrangement consisting of suitable size of 4 Pole MCB and 4 pole 2 nos.

contactor (cat-III)with analog time switch, auto manual switch of same make and

suitable input and output Bakelite terminals and with door earthing approved by

Engineer in charge. (A) 32 Amp .

Supplying & erecting approved make SMC press moulded composite FRP. loop-

in, loop-out approx. 2mm thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps& earth bolt of following size of box.

(C)150mm x 125mm x 100mm [deep].

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

Watt assembled on single MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast powder

coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)(iv) 22-24 Watts, Surge - 2KV,IP-

20, conventional 4 feet CAT-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

Watt assembled on single MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast powder

coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.(i) 5-10 Watts, Surge-2 KV, IP-20,

conventional 1 to 2 feetCAT-III

Making trench in soft soil of suitable width of 90 cm deep for laying cable or

79 locating the fault all over the run and back filling the same and making the surface 500 mtrs.

as normal ground. 46.46 ₹

Supplying stand first AID box with antiseptic cream, medicine for use on wounds

due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-

aid) adhesive tape for medicinal user, Scissors, anti-septic solution (Savlon or

similar) etc. (All above contents shall be of standard makes)

Supplying and erecting floor mounting stand for keeping four nos. of FIRE buckets

comprising 1500 mm in length, 900 mm height frame made out of 30mm X30 mm X

4 mm angle iron with cross supports for legs, welded with 4 hooks and duly

painted with one coat of red lead and two coats of approved enamelled silver paint.

Providing and fixing printed instruction chart both in English and Gujarati and

82 duly framed with front glasses, for treatment of person suffering from Electric 6 nos.

shock with minimum 50" diagonally size. 130.29 ₹

Providing & erecting open well type horizontal mono block pump set with

stainless steel body having following specification (A) 0.5 H.P. single phase open

well motor pump set having discharge of 115 LPM @ 15 mtr. head suitable for

mm dia. delivery pipe with control panel CAT-II

Supplying & erecting approved make LAN cable of following size in existing pipe

as per direction. [C] CAT - 6. for cctv points. 45.45 ₹

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar

Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy

Frame With Twin Wall Profile, Front Cover : High Transmission Low-Iron

Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax:

0/+5, Module Efficiency should be approx. 18%-21%, Normal operating

temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and

Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free

Modules, Thep. temp. co-efficient of the PV module shall equal or better than -

0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit

Production:- 4 to 5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product

warranty and 25 year Linear Power Warranty.,

Solar Inverter: MPPT Range: 80-1000 V, Max efficiency: 97.5% - 98.9%, O/p

Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power Factor: ~1, O/P

THDi: <3%, Operating Tempreture Range: -25~60°C, Anti-islanding Protection:

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor

Detection Integrated, Residual Current Monitoring Unit Integrated, Output Over

Current Protection Integrated, Output Short Circuit Protection Integrated, Output

Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD &

APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting Structure:

Seamless Box Pipe / 'C' Channel of suitable size for rooftop solar installations with

good stability agaist wind & weight load., Hot Dipped Galvanized steel coils.

suitable arrangement for base plate for foundation , solar panel mounting, the

structure should be suitable for carry the load of solar panel,wiring, sprinkler

system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc.

the nut bolt used for installtion of stucture should be (SS 304) quality. and Balane of

System with necessary Swithgears (Suitabel size and protection of ACDB & DCDB),

inter connecting wiring, earthing system, lightining arrester system, all liasoning

work with various gov. dipartment like state nodal agency,DISCOM & CEIG is

included in agency scope . (Excluding GEDA Application fees, Solar connectivity

Charges, Meter connectivity Charges, Meter testing Charges.) .

(D) Grid Tied Solar Power System: 26 - 50 kW (3 - phase). 3 KW 42156.39 ₹

Tender Value In Words

I/We am/are willing to carry out the work at…% above/below per cent (Should be writen in figures and words) of the

estimated rate mentioned above. Amount of my /our tender works out as

Estimated amount put to tender

Estimated amount put to

Deduct………% below Deduct………% below

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

1 Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done

3 GST and Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017

Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in

R.C.C. items where there is a change as per actual mix design the cost of difference of cement consumption have been

deducted from the rate of original item at the rate of input rate mentioned

4 in all the tender