Providing security room at West entrance gate in S V Balamandiram, Tirupati

Demolishing and disposal of unserviceable materials within 100 metres lead - Unreinforced cement concrete up to 15cm thickness

Conveyance of excavated surplus earth/debris to a distance 3kms from the site of work at the place specified by the Engineer-in-Charge including loading and unloading etc., complete as directed during execution.

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental, labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work including Ordinary soil-Manual means upto 3m depth.

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Cement Concrete (1:4:8) using 40 mm (0.54 Cum), 20mm (0.27 Cum) and 12 mm (0.09 Cum)nominal size hard broken granite crushed metal from any source conforming to the relevent ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing,machine mixing, cost and conveyance of all materials etc., complete.

Cement Concrete (1:2.5:5) using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing, machine mixing, cost and conveyance of all materials etc., complete.Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Construction of Brick Masonry in CM (1:6) using well burnt Bricks 2nd class or ground moulded (Non modular or traditional size) (230 x 110 x 70 mm) including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick partition walls in C.M.(1:4) using well burnt bricks 2nd class or ground moulded (Non modular or traditional size) bricks (230X110X70 mm) including curing, cost and conveyance of all materials etc,. complete

Plastering using best river sand including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

.do. In CM(1:5) 12 mm thick

.do. In CM(1:5) 20 mm thick

.do. In CM(1:3) 12 mm thick

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kg),. 10 mm HBG crushed metal, 0.362 cu.m (471 kg) , sand 0.407 cu.m (616 kg.) and cement 380 kg with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC) etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department but including cost of centering, shuttering charges and excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402).

Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kg/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + or - T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

For plinth beam

For lintel beam

-do- For Roof slab (Excluding cost of Centering Charges)

Hire charges for centering & scaffolding - using steel scaffolding pipes, Jack props, wallers, foot plates, brackets, steel centering plates etc., for the following structures, including retaining of water for curing and removing of centering etc., complete as directed during execution complete. (Proper slopes to drain off wash /rain water shall be provided as directed). Roof slab up to 150 mm thick

Supply and placing of the M20 Design Mix using of 10 mm HBG crushed metal 0.480 cu.m, 6 mm HBG Crushed metal 0.320 cu.m, sand 0.400 cu.m and cement 350 kg with water cement ratio of 0.53 (185.50 ltrs/cu.m of CC) etc., from any source conforming to the relevant ISI standard including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing including centering charges, shuttering charges etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of steel and its fabrication charges, for finished item of work

-do- 50mm thick precast slabs using 10 mm graded aggregate of HBG crushed metal from any approved quarry with necessary reinforcement excluding cost of steel and tying of grills, centering charges but including cost of necessary form work and cost and conveyance of all materials curing as directed by the department.

RCC M20 Design mix precast slabs 80 mm thick using 20 mm size graded HBG crushed metal

RCC M- 20 Design mix using 20mm HBG crushed metal 0.480 cu.m , 10mm HBG crushed metal 0.320 cu.m , sand 0.400 cu.m and cement 350 kg with water cement ratio of 0.53 (185.5 Lit per cu.m of CC ) etc. horizontal plain sunshades or lofts projecting from the face of the wall 65mm average thickness,80mm thick at the face of the wall and 50mm thick at the free end and cast monolithically with the lintels or tailed to the full thickness of the wall where there are no lintels using 20mm size graded machine crushed hard granite metal (coarse aggregate) from any source conforming to the relevant ISI standards including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing , etc.,complete, but excluding cost of centering charges and excluding cost of steel and its fabrication charges for finished item of work. - do - 0.60 m width

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars of below 36 mm Fe-500/ Fe-500D (as per IS 1786 - 2008) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire,2 nos of 20G binding wire in tandem are to be strictly adhered). Note: Unless otherwise fabrication and placement of steel, no pre-pament shall be made against the supply of steel reinforcement

Finishing the sides of walls with I st quality glazed red or white full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8 mm conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M.(1:3), 12 mm thick & Cement slurry of 33 Kg/10sq.m shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls). (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply). -

Flooring with Double charged (with double layer pigment) / multi charged stain free full body porcelain vitrified tiles of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs.1st quality of following varieties of series and shades set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & joints with spacer joints with 3 mm wide jointed neatly with filer material of cement/epoxy grout/white cement paste to full depth mixed with pigment of matching shade as directed during execution, including cost and conveyance of all materials, etc., complete - for finished item of work.

Supplying and fixing in position Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 35 mmthick conforming to IS:2202 of standard make with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, Single leaf using Best Indian Teak wood frames of size 75mm x 100mm without threshold plate, including cost of M.S "Z" Hold fasts of 230 x 50 x 6mm, M.S Powder coated Butt hinges of 125 x 65 x 2.12mm, screws, nails, etc., complete, (excluding cost of other fixtures which will be paid separately but including labour charges for fixing the fixtures).

Supply and fixing of cupboard shutter using teakwood scantling of size 50mm X50mm teakwood as outer frame and 50mm X 30 mm of size teakwood for shutter frames , 8mm thick Bison Lam as panel to each shutter consist of 2 Nos 75mm long tower bolt – 2 nos 75 mm big handle the and other shutter will have 1 no of cupboard lack , 1 No of 75 mm long handle and 75mm10mmX1mm thick SS hinges- 2 Nos for each shutter. The above frame will be fixed to the wall with screws, the rate inclusive of screws, handle, etc., complete at site of work.

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint Gr-I over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply of Anodized Alluminium Aldrops sliding door bolts 16 mm X 300 mm (3T- pieces)

Supply of Anodised Alluminium tower bolts 12 mm dia with ISI Mark IS 204 - 12 mm x 250 mm long

Anodized Aluminium Door Handles (IS:208) of 150 mm long

Providing and fixing factory-made uPVC any colour sliding glazed window up powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealant . Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. to 1.50 m in height ensioncomprising of uPVC multi chambered frame with in built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket/TPV, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealant . Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

-do- Three track three panels sliding window with fly proof SS wire mesh(Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing factory made UPVC white colour fixed glazed Windows / Ventilators comprising of UPVC multichambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),uPVC extruded glazing beads of appropriate dimension, EPDM gasket,G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plasticpackers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (ifrequired) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof siliconsealant over backer rod of required size and of approved quality,

all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes and silicon sealant. Note: For uPVC frame, sash and mullion extruded profiles minus 5%tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Fixed windows / Ventilators made of (small series) frame 47 x 50mm & mullion 47 x 68 mm both having wall thickness of 1.9 ±0.2 mm and single glazing bead of appropriate dimension

Providing Unplasticized PVC SWR Rain water downfall pipes for the following dia with ISI:13592 Type -A mark with necessary shoes, bends, collars etc., including making holes in walls, RCC slabs, beams, columns, including fixing with necessary wooden plugs (where it is required pipe clear of wall, wooden blocks of size equal to that of ears of the pipe shall be used), screws, iron clamps of 18 G and making good the same including cost and conveyance of all materials and incidental charges etc., complete as directed during execution. - do - 110 mm dia PVC pipe with wooden block of size 150mmx50mmx50mm

Supplying & Fixing Indian make Flat Back Wash Hand Basin of size 550 x 400 mm - single C.P. Pillar cock.1st quality conforming to IS:2556-Part-4:1972 with ISI mark or equivalent approved by the department, with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams complete with standard CI brackets including wooden block

Supplying and fixing towel rod (CP) of 24'' long and 3/4'' dia

Supply and Fixing 12.7mm NP two way Angle cock Indian make heavy duty

S&F 12.7 mm dia NP pillar cock heavy duty Ist quality Indian make

Supplying and fixing of BITW coat hanger of size 0.60 x 0.076 x 0.025 m including finishing smooth the teak wood reapers and polishing with two coats of French Polish over Bee waxing of approved quality and fixing the specified (CP or aluminium ) coat hooks of different sizes of required numbers at equal spacing as directed during execution and fixing the coat hangers to the walls including cost and conveyance of all materials like screws, nails etc( excluding cost of hooks and fixing charges).

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from identical CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007).

28.60 mm OD pipe SDR - 13.50

22.20 mm OD pipe SDR - 13.50

Supply of 25mm PPR Ball Valve conforming to DIN Standards 8077/8092

Painting two coats for internal walls new plastered surface with Acrylic Emulsion paint over a primary coat (total three coats) interior grade having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and shade, after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site, cost of brushes to have smooth finish, and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for internal walls.

Painting two coats for new external walls with Acrylic Emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and shade, over a priming coat with ready mixed cement primer (water thinnable) for exterior Grade-2 for new work (totally three (3) coats), after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including brushes to have smooth finish, cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for new external walls.

Painting Two coats for New Wood Work with Ready mixed Synthetic Enamel paint in all shades Grade-I over a primer coat (Total three coats) having VOC (Volatile Organic Compound) content less than 50 grams/liter approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

Rupees Nine Lakh(s) Ninety Three Thousand Five Hundred Forty Four And Paise Forty Four Only