385 DDRC Palanji Mukku Punnootharamukku Road in Div9(RKI)

Amount

Bituminous re surfacing

od1052290/2020_2021 : Preparation of Foundation for Embankment<br><br>Scarifying Existing Bituminous Surface to a Depth of 50 mm by Mechanical Means<br><br>Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m by mechanical means

4.9 : Wet Mix Macadam <br> Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. <br> By Mechanical Means with 1 km lead

75.5.1.1pb : Prime Coat - Low porosity - With Packed Bitumen Rates <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

75.5.2.3pb : Tack Coat - With Packed Bitumen Rates <br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.9.2.2.Pa : Plastic Roads - Bitumen S-65 <br> 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder <br> Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 (with 7% of bitumen replaced by shredded waste plastic) <br> Case - I By Manual Means <br> (II) Bitumen (S-65) (VG - 30)

75.5.12.A.3.2pb : Seal Coat - Manual Means - Type C - Bitumen S-65 - Packed Bitumen Rates <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> A. By Manual Means <br> Case III : Type C <br> (II) Bitumen (S-65)

drain construction

11.1.1.1 : Excavation for StructuresEarthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I.Ordinary soil(i)Upto 3 m depth

od1046694/2020_2021 : od47238/2019_2020 :Providing concrete for plain/reinforced concrete in open foundations complete as per&lt;br&gt;drawings and technical specifications Clause 802, 803, 1202 &amp; 1203&lt;br&gt;I.P.C.C grade M 10Excluding formwork(Modified item 11.4.1.1)&lt;br&gt;(i)Nominal mix 1:3:6

11.4.2.1 : Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 II.P.C.C grade M 15(i)Nominal mix (1:2.5:5)

od1046957/2020_2021 : od49068/2019_2020 :Providing concrete for plain/reinforced concrete in open foundations complete as per&lt;br&gt;drawings and technical specifications Clause 802, 803, 1202 &amp; 1203&lt;br&gt;IV.P.C.C grade M 20 (Excluding form work) modified 11.4.4

11.4.4 : Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203IV.R.C.C grade M 20

11.8 : Supplying, fitting and placingTMT bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

ROAD CONCRETING

od1052677/2020_2021 : Surface dressing of the ground in all kinds of soil including&lt;br&gt;removing vegitation and inequalities&lt;br&gt;not exceeding 15cm deep and disposal of rubbish, lead up to 50m and lift up to 1.5m

od1052684/2020_2021 : Plain cement concrete pavement ,thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M 20 (grade),coarse and fine aggregates conforming to IS 383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork(steel channel, wedges,steel plates including levelling the formwork as per drawing),spreading the concrete with shovels,rakes,compacted using needle vibrator and finished in continuous operation including provision of contraction and expansion ,construction joints curing of concrete slabs for 14 days, water finishing to lines and grade as&lt;br&gt;per drawing and Technical&quot;&lt;br&gt;Specifications clause 1501 (Form work included)

BERM CONCRETING

od1047026/2020_2021 : construction of plain cement concrete pavement thickness of asper design over prepared subgrade/sub b ase with 43 grade cement or any other typeas per clause 1501.2.2M 20grade, caorse agregate conforming ti IS 383 maximum size of coarse aggrgatenot exeeding 25mm muxed inconcrete mixer fo not less trhan.2cum capacity and appropriate weigh bather using approved mix design laid in approved fixed side form work (steel channel wedges steelplates including vibrtor andfinished in continous operation includuing provision of constuction expansion jionts curing of concrete slab for14 days with water finished to lines and grade as per drawingTEChnicalspecificationclause1501.

10.4.A.1 : Direction and Place Identification signs with size more than 0.9 sqm size board <br> A. Retro-reflectorised Traffic Signs <br> 1 Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

ANIL AHAMMAD HABEEB

Bidder Name

KDLCCSQ1182

ANIL AHAMMAD HABEEB