REPAIR TO JOINERY, FLOORING, CEILING, ROOFING, TILING, WINDOW, GLASS PANE, DRAIN, SECURITY WALL, SEWAGE LINE, SEWAGE CLEANING ETC AND PERIODICAL SERVICES AT DIGIANA, RAMGARH AND BD BARI MIL STN UNDER GE KALUCHAK

Amount

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified & directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.

Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each, complete all as specified & directed.

Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each and refixing in the same opening after carrying out necessary repair, complete all as specified & directed.

Pressed steel frames of size 125mmx60mm made of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate., complete all as specified & directed. Note : PCC for filling of hollow portion shall be measured and paid for separately.

PCC 1:3:6, nominal mix, type C1, using 20mm graded crushed stone aggregate as in back fill of chowkats and bed plate of holdfast and similar items, complete all as specified and as directed.

35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified & directed.

35mm thick 2nd class hard wood (Sal/Hollock), glazed and skeleton shutters (factory made), open rebated and prepared to receive glass or gauge etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I, complete all as specified & directed.

Solid PVC door/cup board frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified & directed.

Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet 5mm thick to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete as specified & directed.

Mild steel galvanised wire cloth 0.63mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or 2nd class soft wood beading etc, complete all as specified & directed.

Mild steel galvanised wire cloth 0.63mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or 2nd class soft wood beading etc, fixed in repairs, complete all as specified & directed.

Butt hinges, medium weight, cold rolled, mild steel 100mm long, complete all as specified & directed.

Aluminium handle, cast type, anodised, 150mm long, complete all as specified & directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, 300mm long, complete all as specified & directed.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long, complete all as specified & directed.

Steel locking bolts with mild steel electrogalvanized plate and bright bolt not less than 10mm dia, 100mm size, complete all as specifed & directed.

300mm ordinary rat tail rod pattern door spring including roller and roller plate of mild steel and fixed to pressed steel frame / MS frame/ wooden chowkhats including necessary welding work etc where-ever required, complete all as specified & directed.

18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber framed work as in cup board shutters, shelves etc., fixed in repairs, complete all as specified & directed.

18/19mm thick block board, grade 2 quaility, interior grade, commercial type, fixed with screws to timber frame work as in cupboard, fixed in repairs, complete all as specified & directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 40mm, complete all as specified & directed.

40mm dia, copboard knobs fixed with nut, screw and washer of mild steel, brass polished, complete all as specified & directed.

100mm size Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frame or stone, concrete or brick surrounds, glazed with putty or fixed with beads, n exc 1.5 sqm, complete all as specified & directed.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads or glazing pins in metal frame in squares not exc. 0.5 Sqm in each pane, complete all as specified & directed.

3mm thick figured glass, pin headed type and glazing with oil putty or wooden beads or glazing pins in squares not exc. 0.5 Sqm in each pane, complete all as specified & directed.

Factory made box type steel windows comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube with double side shutters (Wire Gauged shutter and Glazed Shutter), side hung shutters with MS handles and MS stays dovetailed or welded including 02 nos MS Tower Bolt 150mm long for each leaf, 8 mm square guard bars at spacing as shown in drawings, MS flat iron frame work, MS hinges, tarred hold fast, PCC 1:2:4 type B1 as in bed of hold fast, 01 No. per leaf of stopper of 100mm size, one coat of red oxide zinc chrome primer etc, complete all as specified and shown as drawing No. CEPZ/CTD-31/2013 sheet 1/2, 2/2 and CEPZ/CTD-32/2013 sheet 1/2, 2/2. Note : a). Wire cloth & sheet glass shall be measured and paid seprately under respective items. b). Rate of both type of shutters and grills/guard bars is inclusive in the quoted rate.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete including one shop coat of red oxide zinc crome primer including taking down old unserviceable ventilator, complete all as specified & directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified & directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified & directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6 but except brick i.e. using serviceable bricks obtained from Srl item No. 29 here-in-before, complete all as specified & directed.

Demolition of cement concrete (un-reinforced) of any description in any position not otherwise specifically provided for, complete all as specified & directed.

75mm thick PCC 1:3:6, nominal mix, type C1, using 20mm graded crushed stone aggregate as in plinth protection, surface finished even and smooth without using extra cement, complete all as specified & directed.

25mm thick PCC 1:2:4 nominal mix, type B-1, using 20mm graded stone aggregate as in floors, finished even and fair to receive floor finishes, complete all as specified & directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed.

Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:4, complete all as specified and directed.

Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm on vertical surfaces such as skirting/dado etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 10mm thick screed layer in cement mortar 1:4, complete all as specified and directed.

Glazed ceramic coloured tiles of size 300mmx450mm thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

Granite (black), 20mm thick as in floor, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting, polishing & half rounding of exposed edge of stone over & including 15mm thick screed bed in cement mortar 1:4, complete all as specified & directed.

100mm thick PCC 1:4:8 (nominal mix), type D-2 using 40mm graded crushed stone aggregate as in sub base of floor, complete all as specified & directed.

Precast designer coloured heavy duty full body paving tiles (factory made) of size 300mmx300mm x 10mm, top layer glazed made in any type of cement and pigment, in required patterns as approved by GE in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:4, complete all as specified & directed.

Taking down existing switch board of any description and refixing the same after repair of tiling/ plastering work etc, complete all as specified & directed.

Taking down cement plaster on brick or stone surfaces of wall/ceiling, chajjas, roof projections etc upto triple storey etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified & directed.

15mm thick rendering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified & directed.

15mm thick rendering in cement mortar 1:6 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified & directed.

10mm thick rendering in cement mortar 1:4 on concrete surfaces of chajjas, upward fascias, ceiling and similar items, surface finished even and smooth without using extra cement, complete all as specified & directed.

Dismantling water tanks of capacity of 1000 litres, complete all as specified & directed.

Dismantling water tanks of capacity of 500 litres, complete all as specified & directed.

Rotationally moulded polyethylene water storage tank (cylindrical vertical with closed top) triple layered, hoisted & fixed in position of capacity 1000 ltrs including making necessary arrangements for fixing of inlet, outlet, over flow pipe, wash out pipe etc, complete all as specified & directed.

Rotationally moulded polyethylene water storage tank (cylindrical vertical with closed top) triple layered, hoisted & fixed in position of capacity 500 ltrs including making necessary arrangements for fixing of inlet, outlet, over flow pipe, wash out pipe etc, complete all as specified & directed.

Cleaning and removing all scale and dirt, etc, from tanks of capacity 500 ltrs and from mouths of circulating pipes, etc., complete all as specified & directed.

Cleaning and removing all scale and dirt, etc, from tanks of capacity 1000 ltrs and from mouths of circulating pipes, etc., complete all as specified & directed.

20mm bore, ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210gms), fixed in repairs, complete all as specified & directed.

Taking up or down steel tubing and connections 20mm bore, complete all as specifed & directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specifed & directed.

Galvanized iron water tubing, medium grade, 20mm bore with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Galvanized iron water tubing, medium grade, 15mm bore with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., fixed complete to walls and ceilings or laid in floors , complete all as specified and directed.

Refixing old steel tubing and connections of 20mm bore in new or old position (Walls, ceiling, floors etc.) including cleaning for refixing, complete all as specified and as directed .

Refixing old steel tubing and connections of 15mm bore in new or old position (Walls, ceiling, floors etc.) including cleaning for refixing, complete all as specified and as directed .

Stop valves, cast copper alloy, 20mm bore, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., fixed in repairs, complete all as specifed & directed.

Bib tap, 15mm bore, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified & directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered `Hot’ or `Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, fixed in repairs, complete all as specified & directed.

Stop valves, 15mm bore, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure, both ends screwed for iron pipe or for union etc., fixed in repairs, complete all as specifed & directed.

Angle valves, 15mm bore, fancy type, chromium plated, cast copper alloy with capstan head, screwed down, high pressure, both ends screwed for iron pipe or for union etc., fixed in repairs, complete all as specifed & directed.

Brass chromium plated WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore of pipe, fixed in repairs, complete all as specified & directed.

Brass chromium plated shower rose of 125mm size with or without swivel joints, fixed in repairs, complete all as specified & directed.

PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified & directed.

Vitreous china wash down water closet (Pedestal pattern), white with ‘P’ or ‘S’ trap, fixed with screws of suitable size including making connections to trap and to flush pipe, fixing flushing cistern etc. and making good to floors, fixed in repairs, complete all as specified & directed.

Vitreous chinaware squatting pan, 'Orissa Pattern' size 580mm x 440mm with integral foot rests, white, with ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, fixed in repairs, complete all as specified & directed.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, fixed in repairs, complete all as specified & directed.

Vitreous china, wash hand basin, flat back, white of size 580mmx450mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, chain and plug, porcelain stopper including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs, complete all as specified & directed.

32mm dia waste pipe of polyethylene for wash hand basin, complete all as specified & directed.

Jet spray CP with 1 mtr long tube for 15mm bore pipe and mild steel chromium plated hinging device for pedestal type WC, fixed in repairs, complete all as specified & directed.

Towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs, complete all as specified & directed.

PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, complete all as specified & directed.

Dismantling of cast iron or reinfored concrete drain pipes, jointed in cement mortar and taking out of trenches or fixed with walls, if required, internal dia of pipe 75mm / 100mm, complete all as specified & directed.

PVC (SWR) pipes, 110mm bore, single socketed, in any length with rubber ring joints, fixed to walls with clamps, complete all as specified & directed.

110mm bore PVC (SWR) bends any radius, complete all as specified & directed.

PVC (SWR) branch piece, single (single Y) equal or unequal, 110mm bore, complete all as specified.

PVC (SWR) junction single (Single T) equal or unequal, 110mm bore, complete all as specified & directed.

PVC (SWR) vent cowl of size 110mm bore, complete all as specified & directed.

PVC (SWR) pipes, 75mm bore, single socketed, in any length with rubber ring joints, fixed to walls with clamps, complete all as specified & directed.

75mm bore PVC (SWR) bends any radius, complete all as specified & directed.

PVC (SWR) branch piece, single (single Y) equal or unequal, 75mm bore, complete all as specified.

PVC (SWR) junction single (Single T) equal or unequal, 75mm bore, complete all as specified & directed.

Complete removal of the existing sunken treatment including roughening and preparation old surfaces of concrete floor by picking, scurubbing down with steel brushes, sweeping clean and washing down with water to remove dust etc and applying the following treatment :- (a) 15 thick rendering on fair faces of brick work or cement surfaces in cement mortar 1:4 with using integral water proofing compound as per manufacturer instructions by weight of cement to sunken portion including wall of sunken portion with proper slope towards outside and finishing cement concrete or brick work surface even and smooth using extra cement, finishing concrete including walls of sunken portion with proper slope. (b) Applying 2nd course of bitumenous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the screed bed. (c) Applying 3rd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm.

(d) Applying 4th course of APP (Atactic Polypropylene) modified polymeric membrane 3mm thick weight not less than 3.6 Kilogram/Square Metre with 160 Grams/Square Metre non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kilogram/Square Metre. Note : Ponding shall be done in sunken portion area by filling water which shall be kept there for 48 Hours. In case a slightest indication of seepage/leakage is noticed, the same shall be rectifird by grounting the effected area at no extra cost. Thereafter, ponding shall be repeated till there is no indication of seepage/leakage. The arrangements of ponding to be included in quoted rates and nothing shall be admissible on this account.

Stainless steel sink with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union etc., overall size 915x460mm with bowl size 410x330x160mm, 40mm dia PVC waste pipe of adequate length, fixed in repairs, complete all as specified & directed.

20mm dia PVC coated drapery rods in one length per door/window, fancy type (engraved rods), designed & colour as approved by GE, provided with one no. funnel and bracket on each end, complete all as specified & directed.

Preparation of new plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of chalk whitening, complete all as specified.

Preparation of new plastered or concrete surfaces of walls and applying two coats of cement base paint over a coat of cement primer, complete all as specified & directed.

Preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified & directed.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified & directed.

Preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified & directed.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying one coat of oil emulsion distemper, complete all as specified & directed.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying one coat of cement base paint, complete all as specified & directed.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying one coat of white wash, complete all as specified & directed.

Preparation of old decorated plastered or unplastered surfaces of ceiling by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying one coat of white wash, complete all as specified & directed.

Preparation of old painted wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified & directed.

Preparation of old decorated steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified & directed.

Aluminium anodised frame (for window) of size 124.60mm x 44.45mm made out of 1.60mm thick aluminium section, powder coated (minimum thickness 50 micron), fixed to floor/wall with 03 Nos 'U' channels all around for sliding of 03 Nos window channels, fixed to cill/wall with plugs & screws, complete all as specified & directed.

Aluminium anodised frame (for window) of size 124.60mm x 44.45mm made out of 1.60mm thick aluminium section, powder coated (minimum thickness 50 micron), fixed to floor/wall with plugs and screws, complete all as specified & directed.

Aluminium anodised powder coated (minimum thickness 50 micron) window/ventilator shutter, section of size 44.45 x 44.45mm made out of 1.6mm thick aluminium sheet/section including necessary jointing cleats, glazing clips, rubber packing, suitable handle 1 No in each shutter, tower bolt, hinges 110mm long, anodised aluminium snap beading screws, complete all as specified and directed. Note : Sheet glass will be measured and paid separately under respective item.

5.50mm thick tinted glass as in aluminium door/ window/ ventilator with aluminium hollow beading/ glazing clip size 19mm x 17mm made out of 0.70mm thick hollow section weighing not less than 0.97 Kgs/RM including rubber gasket, complete all as specified & directed.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, complete all as specified & directed.

Pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in as in ridges, hips, valley gutters, drip and straight flashings, fixed with self tapping screws, complete all as specified & directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering, complete all as specified & directed.

Corrugated galvanized iron sheets 0.63mm thick, grade ‘O’, with 120gm square metre zinc coating fixed with `L’ & `J’ hooks and washers as in roof covering with two corrugation side lap (Horizontal distance of side and end lap shall not be less than 145mm and 150mm respectively and depth of corrugation shall be 12.5mm), complete all as specified.

Plain, galvanized iron sheets 0.63mm thick with 120gm square metre zinc coating in stepped flashings (measured as the minimum rectangle from which the pieces can be cut), complete all as specified & directed.

Suspended false ceiling system using 4mm thick high pressure steam cured fibre cement pre-primed textured varient board (classic), ISI marked, conforming to IS:14982-2000 over and including GI snap grid frame work for false ceiling, grid size 605 x 605 mm with GI angle of size 24x24mm, main runner ‘T’ of size 24x38mm, secondary runner ‘T’ of size 24x28mm with 6mm GI wire with butterfly clips for leveling, fastners, supports, plugs to walls/joists etc all as per manufacturer’s Instructions, including making holes, cutting chasis and making good existing walls in cement mortar 1:3 or PCC 1:2:4 type B1, complete all as specified and directed. Note : All steel members shall be hot dipped galvanised with zinc coating not less than 120 gm/sqm.

PCC 1:2:4, nominal mix, type B-0, using 12.5mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified & directed.

Steel peg stay as per existing pattern suitable for steel windows with side hung shutters, fixed in repairs, complete all as specified & directed.

20mm thick Granite (of any shade/type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting, polishing & half rounding of exposed edge of stone over & including 15mm thick screed bed in cement mortar 1:6, complete all as specified & directed.

Cutting/ removing of vegetation/ tree grown on wall/roof of buildings from routes and clean the surface as to the entire satasfication of Eng-in-charge, complete all as specified & directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified & directed.

Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition), complete all as specified & directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified & directed.

Dismantling of old rusted galvanised barbed wire/plain GI wire of any size & type in any position, complete all as specified & directed.

Dismantling posts or structs (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground, posts embedded in concrete, brickwork, masonry etc., complete all as specified & directed.

Excavation n exc 1.50m deep and getting out from existing drains, removing excavated material, loose earth accumulated, debris, vegitation to a distance as directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

Excavation over areas not exc. 1.5m deep in any type of soil and getting out, complete all as specified & directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed & directed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

PCC 1:4:8 nominal mix, type D-2 using 40mm graded crushed stone aggregate as in foundations, filling & mass concrete, complete all as specified & directed.

75mm thick PCC 1:3:6, nominal mix, type C2, using 40mm graded crushed stone aggregate as in sub base of floor, hard standing, path, pavings etc, surface finished even and smooth without using extra cement, laid in alternate bays, complete all as specified & directed.

Precast designer coloured paver tiles (factory made rectified) of size 300mmx300mm x 20mm, top layer glazed made in any type of cement and pigment, in required patterns (compressive strength not less than 250 Kg per Sqcm) as approved by GE in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified & directed.

60mm thick factory made chamfered edge cement concrete paver block of M-35 grade confirming to IS-15658-2006 of approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified & directed.

100mm thick PCC 1:2:4, nominal mix, type B2, using 40mm graded crushed stone aggregate as in pavement, hard standing, path etc, surface finished even and fair, laid in alternate bays including form work, complete all as specified & directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan to any radius, half brick thick walls built in cement mortar 1:4, complete all as specified & directed.

Barbed razor tape concertina coil SG hot galvanised spring tensile wire as approved by GE, dia of coil when stretched 1000mm having minimum number of circles 12 RM to 13 RM, minimum number of clips 15/RM & minimum weight of coil 0.96 Kg/RM hot dip galvanised, complete all as specified & directed.

Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete all as specified & directed.

Mild steel framed work as in grills, gratings, etc. with ends of bars shouldered and or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified & directed.

Mild steel work in swan neck angles embeded in RCC columns, posts & struts in fencing including cutting tops to shape as directed including drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc), necessary drilling, bolting or riveting, conforming to Fe-290 grade E-165, complete all as specified & directed. Note : Unit rate shall deemed to include locking holes after fixing of barbed wire and welding to bent up portion as directed.

RCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified & directed.

BLANK

TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified & directed.

TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified & directed.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc., complete all as specified & directed.

PCC 1:2:4, nominal mix, type B-2, using 40mm graded crushed stone aggregate as in surface channel and drains including necessary form work, complete all as specified & directed.

Excavation in post holes (or similar holes) each not exc. 0.50 cum, in any type of soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc. 25cm, watering and removal of excavated materials to a distance n. exc. 50m and making good surfaces, complete all as specified & directed.

PCC 1:3:6 nominal mix, type C-2 using 40mm graded crushed stone aggregate as in foundations, filling & mass concrete, complete all as specified & directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan in any type of soil and getting out, complete all as specified & directed.

All as per Srl item No.145 above but depth exc 1.5m and not exc. 3.0m deep in any type of soil.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, internal dia of pipe 200mm, complete all as specifed & directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, internal dia of pipe 150mm, complete all as specifed & directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, internal dia of pipe 100mm, complete all as specifed & directed.

Concrete bed to 200mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:4:8 (Nominal mix) type D-2 using 40mm graded stone aggregate, and tested, complete all as specified & directed.

Concrete bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:4:8 (Nominal mix) type D-2 using 40mm graded stone aggregate, and tested, complete all as specified & directed.

Concrete bed to 100mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:4:8 (Nominal mix) type D-2 using 40mm graded stone aggregate, and tested, complete all as specified & directed.

Salt-glazed stoneware drain pipe, grade ‘A’ internal dia of pipe 200mm, laid in trenches and jointed, complete all as specified & directed.

Salt-glazed stoneware drain pipe, grade ‘A’ internal dia of pipe 150mm, laid in trenches and jointed, complete all as specified & directed.

Salt-glazed stoneware drain pipe, grade ‘A’ internal dia of pipe 100mm, laid in trenches and jointed, complete all as specified & directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching, internal dia of pipe 100/150/200mm, complete all as specified & directed.

PCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in benching, water troughs and the like including necessary form work, complete all as specified & directed.

Precast cement concrete 1:2:4 (nominal mix), type B-1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for manhole etc.), and similar articals with plain faces, set in cement mortar 1:4 including necessary form work, complete all as specified & directed.

Cleaning/ clearing of sewage line (including manholes) of 100mm to 200mm bore of any description, underground at any depth, removing any type of blockage including desilting, descaling & dechocking of drains as well as manholes with combined high pressure water jetting cum suction (vacuum) type machine mounted on LCV/ HCV and having facilities of high pressure vacuum and provision of hydraulic application through high pressure thermo plastic fibre based water jetting hose and conical round shape nozzle pipe and flushing after cleaning including removing the same in the tank to a place outside cantonment at the place meant for the purpose by local municipality, complete all as specified & directed.

All as per Srl item No.159 above but cleaning down manually by labour. Note for Srl item No. 159 & 160 The contractor shall keep the sewage line functional throughout the contract period. The unit rate quoted by contractor shall deemed to be inclusive of this aspect.

Desludging / dewatering of septic tanks/ soakage wells including inlet / outlet chambers, removing out all scum, silt, residual sludge (both organic & inorganic in nature) after plugging the incoming sewage lines through combined high pressure water jetting cum suction (Vacuum) type machine mounted on LCV/HCV facility of high pressure vacuum and removing the same in the tank to a place outside cantonment at the place meant for the purpose by local municipality, complete all as specified & directed.

All as per Srl item No.161 above but cleaning down manually by labour.

Cleaning of blocked WC, bathroom & kitchen floor trap including and upto first manhole manually and well flushing with clear water, making the seat functional including depositing the sludge in a pit (including digging of pit) not less than 100 meter away from site of cleaning and covering the deposited sludge with minimum 25cm thick layer of earth and spreading unslacked lime on the pit, complete all as specified & directed.

KAMAL CONSTRUCTION