8222 REPAIR TO HANGER, HELIPAD RUNWAY, TAXI TRACK, HARD STANDING, PATH, DRAIN AND ATC BLOCK AT 23(I) R AND O UNDER GE(E) BAREILLY.

Amount

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc. complete all as specified and directed.

Demolition cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Demolition concrete of any description and in any position not otherwise specifically provided cement concrete complete all as specified and directed.

Dismantling structural steel work including doors , gates but excluding framed truss etc. complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as spd as directed

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished without using extra cement complete all as specified and directed.

M& L for rendering 15mm thick in cement mortar (1:4),finished even and smooth using extra cement to on brick masonary wall surfaces or on fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed.

M & L 40 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over including cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to get mirror finish incl screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and as directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to get mirror polish complete including rendering, 10mm thick CM 1:4 on vertical surface complete all as specified as directed.

M&L 18 mm thick granite of black colour (table rubbed and polished) as in windows cill, in steps, jambs, pillars, cooking platforms and like in cement mortar (1:4) including form work, pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as specified as directed.

M&L for 75mm thick PCC 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base floor / pavings complete all as specified and directed

M&L in repairs for machine pressed pre-cast concrete interlocking coloured paver block, Glossy finish and shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment laid dry over and including 50 mm thick stone dust or sand base and compacted using vibrator complete all as specified and directed.

M&L in repairs for machine pressed pre-cast concrete interlocking coloured paver block, Glossy finish and shape and size conforming to IS-15658-2006 of 80 mm thickness M-40 grade with grey cement and pigment laid dry over and including 50 mm thick stone dust or sand base and compacted using vibrator complete all as specified and directed.

M&L in repairs for machine pressesd pre-cast cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregate) kerb stone including weathering, slightly rounded or chemferred angles and throating complete all as specified.

M&L in repairs for machine pressesd coloured glazed chequered cement concrete 20cm x 20cm x 25cm thick Glossy finish with mixture of grey and white cement in equal proportions and no pigment set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including screed bed or bedding layer of mortar 20 mm thick, in cement mortar 1:6, complete all as specified and directed.

M&L Removal of Existing Waterproofing Treatment and clean the surface. (a) Bonding Coat: Cleaning the surface with wire brush, water jet etc to remove dust, dirt etc. On clean surface applying a bonding coat of Asian paints Smartcare Multi Purpose Polymer mixed with cement (1:1.5) to reduce the existing surface porosity and as a bond coat for the new surface sceed on the top of the same. (b) Resurfacing : Applying and Laying a avg 15 mm thick layer of cementitious polymer modified mortar on the top of the bond coat as per manufacturer's instructions in existing gradient/ slope. Polymer will be added @ 8% to the weight of cement. Solid content of the polymer not less than 54%. The newly constructed surface to be cured with clean water at least for 10 days before applying WP membrane. (c) Surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of screed shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar, Making of Coves/ vata at the junction / corners in using MPP polymer mixed with cement : sand as per manufacturer's instruction for mortar & water curing the same. after curing period of 72 hours proceed with application of Polyurethane coating. (d) Liquid Applied WP Membrane: Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethene with the existing concrete surface. 33 % water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3(Resin:Hardner). Epoxy primer will be done at consumption of 0.2Kg per sqmt.

after above treatment, applying waterproofing treatment to terrace area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving an avg. thickness of 1mm. The coating shall have a dual combination of 280% elongation. The Material will be applied @ coverage 1.2kg /sq.mt. A 10 Years Company Back warranty to be provided after complition of the work. The applicator must show the company authorization.

supply Integral water proofing Liquid of Dr fixit/sika/Fosroc

S & F in repair 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as spd as directed

S&F for 40 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed by Engineer-in-Charge. (Note :- S & F wire mess shall be measured and paid for separately)

S&F 150 mm long floor door stopper of brass body and tongue with hard drawn steel spring complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing

S&F 30 mm thick Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 all as specified and directed.

S&F of Steel windows with pressed steel frame ( size 95x 45x 1.25mm) side hung shutter including box type hinges with steel handle, and steel peg steel complete with glazed openable shutter with glazing bar (open out side) and wire gauged openable shutter without glazing bar (open in side) dovetailed or welded complete all as specified and directed and all as per Drg No TD/088 dt 07 jan 2002 Note:- (i) Two shutter ie wire gauged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit. (ii) Rate for filling of PCC in frame deemed to be included in quoted rate. (ii) MS grill shall be measured and paid seperatly under relevant item of schedule

S&F for steel ventilators fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed. (Note :- Glass shall be measured and paid for separately).

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane (upto 3 story building (MAP area) including Hacking out old, broken glass (any thickness,) size quality or description) from metal frames including punching or drilling out old glazing pins/spring clips complete all specified and as directed.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples in m s window / wooden shutter complete all as specified and directed

S&F 12 mm thick toughned glass door with powder coated aluminium frame including neccessary locking, handle etc with double action floor spring in each shutter complete as requirement of site with suitable height and any type of eaching designed on tougned glass, off cuts complete with finishing wall in CM 1:4, designed approved by Engr-in Charge

S&F 12 mm thick toughned glass partion wall with or without powder coated aluminium frame with any type of eaching designed on tougned glass, off cuts complete as requirement of site with arrangement for suitable height with off cuts complete all as specified and directed.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing or composite panel LDPE core PET coating (both side decorative type) fixed with and including 5.50mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 63x38x1.48mm thick with rawl plug (b) Middle and lock rail : 85x44x1.48mm thick (c) Bottom rail : 114x44x1.48mm thick (d) Top rail/style : 114x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver aluminium stopper, cleat double action floor spring hydraulically regulated made of n.less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part of steel heavy duty (Make Sandhu ISI marked or its equivalent approved make) (g) Making good of wall surface to match with existing surface complete.

S&F Powder coated aluminium sliding windows and frame with movable shutter (sliding on minimum two PVC roller of best quality on two tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire messs fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below:- (i) Window frame : 63x35mm X 1.48 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 19x38x1.48mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) Aluminium fittings such as aluminium suitable fittings for auto interlocking closing (v) Making good of wall surfaces to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium sliding windows and frame with movable shutter (sliding on minimum two PVC roller of best quality on two tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire messs fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below:- (i) Window frame :63x35mm X 1.15 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 19x38x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (v) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

M & L powder coated aluminum window/ doors grills fixing along with frame of following specification, grills with opening 69.4mm X 78.2mm grills thickness shall be of 6.4mm X 5.8mm having weight not less than 2.306 Kg/per sqm shape as ordered with frame channel of 34 X 11mm X1.7mm thick fixed with screw inside of the window all as directed by Engr-in-Charge and all as specified and as directed.

S&F partition wall of powder coated aluminium hollow sections members of size 63.50 mm x38mmx 1.48 mm thick with distance of vertical hollow section, 1.2mtr to 1.8 mtr height of wall having top rails, bottom rails and middle rail of size 63.50 mm x 38mm x 1.48 mm and upto middle rail wall panels shall be covered by 5 mm thick aluminium composite panel LDPE core PETcoating (both side decorative type) with aluminium clip height of middle rail shall be 1 meter from floor and remaining portion above middle rail shall be provided with 5 mm thick glass including eaching approved designed with aluminium stiprs/beadings with rubber gasket as per existing or as provided complete all as specified and directed.

S&F in repairs Aluminium Composite (ALCO) panel exc 3 mm thick ,jointed with screw , cutting , edging, and grooves finished using epoxy silicon composite Resin compound of any colour, fixed on flat or curved surface incl taking down of existing ALCO panel complete all specified and as directed by Engineer in charge.

Material & Labour providing and fixing in repair stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F in repair Venetian blind coloured strip 75 mm top 5 mm thick powder coated aluminium rod rod ends at brackets are moulded type etc complete all as directed.

S& F in repair door closer hydraulically regulated Aluminium (extruded section body), designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

M & L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy dut fixed complete all as specified and directed.

M&L for repairing to existing aluminium doors of any size by straightening of frame / shutter, replacing the detoriated member with new, replacing the broken / non funcional hinges with new, replacing decayed rubber gasket with new, replacing the broken glass pane of any size with new 5.00mm thick tinted glass, replacing unserviceable handle, tower bolt, lock, floor spring, foundation box with governing pivot, top pivot, peg stay etc with new and including taking down and at same place after making the door / window smooth functional complete all as specified and directed.

M&L for E-board/ PVC false ceiling consisting of powder coated GI wall angle, main T and cross T of 25mmX 25 mm X 1.40 mm thick grid frame work, joist, angle/ Tee as directed and mild steel wire hook not less than 6 mm dia with arrangement for adjusting height of ceiling and including provn of 4 mm thick E- Classic board in pannelof size 600X600mm with necessary off cut including dismantling of existing false ceiling and taking down and refixing of Electric fitting carefully complete all as specified and directed.

Providing & fixing 10mm thick plaster of paris false ceiling bending as required shape with two coats of plastic emulsion paint over a coat of primer on decorated surfaces of ceiling including 26 gauge galvanished iron sheet 'C' shaped main member @750 mm C/C cross member 'U' shaped @450 mm c/c and perimeter of 'C' shaped GI wire mesh having aperture 6.5 mm with 26 gauge wire GI wire 6mm dia or more or FI 40x4mm thick for hanging arrangement with MS suspension.fastner spaced @ 450mm c/c in both direction the 'C' member shall be made out of not less than 90mm wide GI sheet strip and side tray as required of approximate size 3.5 Mtr height as required at site complete all as specified and directed.

S&F in repair PVC hollow interlocking wall paneling of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cbm density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement.

S & F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges medium weight stailess steel colled rolled complete all as specified and directed by Engineer-in-Charge.

S&F in repair 300mm, ordinary rat tail rod patttern springs includding roller and roller platewith fixed to wooden/pressed steel frame chowkats with flat iron 40x3mm size 75 cm long with necessary bolts, etc. completed all as specified and directed.

S&F 300 mm long mild steel sliding door bolts plate type stone enamelled black with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

S & F in repair 300 mm long brass sliding door bolts without locking arrangement with screws in internal shutter of bldgs complete all as spd as directed

S&F rotational moulded polethylene water tank of 1000 ltrs capacity, ISI Marked (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 1000 ltr complete all as specified and directed.

S&F rotational moulded polethylene water tank of 500 ltrs capacity, ISI Marked (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 500 ltr complete all as specified and directed.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F GI tube 15 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 15 mm dia & connections complete all as specified and directed.

S&F GI tube 20 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 20 mm dia & connections complete all as specified and directed.

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed

S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia pillar tap , 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including Stainless steel brackets all s directed.

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 55X45X82cm complete including fancy CP pillar tap, CP Waste coupling, waste pipe, complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed.

S&F in Vitreous China counter top oval type coloured wash basin suitable size including swan neck pillar taps with bottle trap ,but including waste pipe fixing on counter with stainless steel brackets complete all as specified.

S & F in repair fancy type 150mm size square brass CP shower rose all as specified.

S&F in repairs 15 mm dia pillar tap fancy type chromium plated complete all as specified as directed.

S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed.

S&F fancy type chromium plated brass two way bib cock with wall flange suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair fancy type brass chromium plated toilet paper holder, complete all as specified. Make hindware or equivalent

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm, complete all as specified. Make Jaguar or equivalent

S&F in repair stainless steel of AE - SI 316 grade tubular towel ring including apair of CP brass bracket complete all as specified.

S & Fin repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified.

S&F in repair 15 mm dia fancy type stop cock, chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed complete all as spd as directed

S & F in repairs Rimless Single piece-WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, Size: 360x675x750 mm, S trap- 300 mm make Jaguar or equivalent including making good to floor complete all as specified and directed.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified.

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified. Make Hindware / parryware or equivalent

S&F in repair vitreous China coloured European type WC with "P" or "S" trap white, including connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed .Model:Sleek fresh dual flush of Hindware Model No Pastel size 47.6x15.5x32 , Parryware Cat No 8177*, Cera Cat No B1810110 snow white"

S & F Brass CP health faucet with 8mm Dia 1.0 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body all as specified and directed. Model :ALD 573 of Jaquar ,Hindware Model No F160002, Parryware Model No T9961A1"

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed by Engr-in-charge.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F Framed work as in tower post stair case,railing and doors of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing FE 290 Gde E-165 (height upto 25 Mtrs high) complete all as specified and directed.

S&F in repairs steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 complete all as specified and directed.

S&F in repair Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

S&F for 0.71mm thick Aluminium plain sheeting Alloy 31000 H4, STUCCO Embossed finish with fixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart incl dismantled also all as spd as directed

S&F in repairs Concertina coil fencing with required dia of 750mm, upto 2.1 mtr high wall with existing Y Shape angle iron placed 2. Mtrs to 3.2 Mtr apart and with 5+5 No (Y Shape) barbed wire with and including necessary fixing GI Stapple and GI Cps for securing coil to retained horizontal complete all as specified and directed with following specification: (i) Dia of coil (Unstreached)-750mm (ii) Number of circles - 50 turn per coil. (iii) Weight of each coil with hessian pack-10.00 to 10.50 Kgs. (iv) Coverage per coil- 6 Rm (v) Central core wire :- made from 2.5mm + dia high tensile wire,galvanised as per IS :-2629.Zinc coating 200 to 230 vsm. (v)Thickness of the tape punched Tape- 0.5 mm+ Note :- Barbed wire measured and paid separetly.

S&F in repairs Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rail straining bolts including securing or tying at crossings with and provisons of galvanised mild steel wire, staples or steel pins etc as directed (each line wire to be measured) complete all as specified and directed.

Material and labour 20-25 mm wide expansion joints upto full depth of concrete slab (250mm) filled with preformed compressible filler board (Silfex supremen base) precut of specified depth provision of closed cell polythene back up rod 25 mm dia (minimum depth over back up rod shall be 14 - 15mm) 02 coats of priming the vertical side of joints and sealing the joints (Top 12mm with and using cold applied polyurethane sealent confirming to requrement of BS - 5212 type FB and applying masking tape on edge at joints to prevent accidental spillage of sealant and removing the masking tape after sealent is applied Sealent should have MAF minimum -+ 30% and manufacturers warrenty for 10 (ten) years complete all as per manufacturer instructions and rate incl for whichever PQC repair upto 0.05 Sqm and depth upto 100mm or along expension joints with epoxy+hardner complete all as specified and directed. Note :- Rate included for taking out all existing filling material including cleaning preparation surfaces for filling new sealing material.

Material and labour 8 to 15mm wide 22-25 mm deep construction joints 02 coats of priming and providing a back up rod 10mm dia and sealent with using cold applied polyurethane sealent (Top 10 mm leaving 2-3 mm recess) confirming to requrement of BS 5212 type FB and applying masking tape on edge at joints to prevent accidental spillage of sealant and removing the masking tape after sealent is applied Sealant should have MAF minimum + 30% and manufacturers warrenty for 10 (ten) years complete all as per manufacturer instructions and rate incl for whichever PQC repair upto 0.05 Sqm and depth upto 100mm or along expension joints with epoxy+hardner complete all as specified and directed by Engineer-in-Charge. Note :- (Rate included for taking out all existing filling material including cleaning preparation surfaces for filling new sealing material.)

M&L Road marking paint for painting lines, dashes, arrows,letters etc on roads, pavements and like etc with thermoplastic paint 2.0mm thick, white or golden yellow after cleaning surfaces complete all as specified and directed. Note :- Rate included for taking out all existing painting including cleaning preparation surfaces for new painting.

M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50mm x 50mm (10 mm gauge welded mesh) & tack, securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and recron 3 S as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of Dr fixit /pidilite new coat ezee at interval of 8 hours cure for the surfaces complete all as spd as directed

M& L for preparation of newly plastered wall surfaces and applying three coats of texture (Domasc ) finished painting with the following process the surfaces should be completely dry and free from loose particles including preparing the surface with emry paper 180 nos and wipring clean and applying one coat of primer and allow drying for 6 to 8 hours then smoothen the surface by filling dints with thin coat of acrylie wall putty after drying for 4 to 6 hours and preparing the surface with emry paper and clean and applying another coat of primer and allow drying for 6 to 8 hours and then emulsion 1 Ltr with 500 ml water and applying with brush follwed by rolling with sponge roller or filter roller, applying three coat with brush and roller with and interval of 3 to 4 hours between successive coat all as per manufactures instruction complete all as specified and directed

M& L for preparation of newly plastered wall surfaces and appltying three coats of texture (Rustic) finished painting with the following process the surfaces should be completely dry and free from loose particles including preparing the surface with emry paper 180 Nos and wipring clean and applying one coat of primer and allow drying for 6 to 8 hours then smoothen the surface by filling dints with thin coat of acrylie wall putty after drying for 4 to 6 hours and preparing the surface with emry paper and clean and applying another coat of primer and allow drying for 6 to 8 hours and then emulsion 1.0 Ltr with 500 ml water and applying with brush follwed by rolling with sponge roller or filter roller, applying three coat with brush and roller with and interval of 3 to 4 hours between successive coat all as per manufactures instruction complete all as specified and directed

M&L for preparation of newly plasted wall surfaces and appltying three coats of texture (Super fine) finished painting with the following process the surfaces should be completely dry and free from loose particles including preparing the surface with emry paper 180 nos and wipring clean and applying one coat of primer and allow drying for 6 to 8 hours then smoothen the surface by filling dints with thin coat of acrylie wall putty after drying for 4 to 6 hours and preparing the surface with emry paper and clean and applying another coat of primer and allow drying for 6 to 8 hours and then emulsion 1 Ltr with 500 ml water and applying with brush follwed by rolling with sponge roller or filter roller, applying three coat with brush and roller with and interval of 3 to 4 hours between successive coat all as per manufactures instruction complete all as specified and directed

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide / zinc chrome primer complete all as specified and directed.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed.

M&L for complete removal of existing treatment on walls etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of oil bound distemper over 1mm thick cement based in double layer wall care putty complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distemper over 1mm thick wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling, etc including cleaning of any mortar drops, fungus efflorescent salts etc. and preparation of old plastered surfaces and applying two coats of oil bound distemper over and including one coat of 1mm thick double coat (JK/Birla) wall care putty complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling, etc including cleaning of any mortar drops, fungus efflorescent salts etc. and preparation of old plastered surfaces and applying two coats of white wash complete all as specified and directed.

M/S ABHISHEK ENTERPRISES

M/S R S Constructions