Construction of Community Sanitary Complex at Mahathma Jyotiba Phule AP Backward Classes Welfeare Residential Educational Society Grils Vonipenta of Mydukur Mandal in YSR Kadapa District

Earth Work excavation and depositing on bank with an initial lead of 10 m and 2 m lift in loamy clayey soils including all labour charges.

Sand filling in basement with watering and tamping including cost and conveyance of all materials and all labour charges etc complete.

CC(1:4:8) mix using 40mm HBG metal including cost and conveyance of all materials and all labour charges etc complete.

Construction of Randam rubble stone masonry in CM(1:6) 2nd sort including cost and conveyance of all materials and labour charges ,seigniorage charges etc complete.

Vibrated Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges. For Square footing

Vibrated Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.Columns Above & below GL

Vibrated Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.For plinth beam

Vibrated Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.For slab beams

Vibrated Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.Roof slab for 115mm thick

Vibrated Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.Septic tank bottom slab

Brick Masonary for superstructure with CM(1:6) prop:)cement:sand)using fly ash lime solid blcks of size 290mm x 225mm x 140mm for Super Structure.

Cost, supply of steel FE 415 including fabrication charges and labour charges etc. complete.

Cost ,supply of iron ventilator grills including fabrication charges and labour charges etc. complete.

Plastering in CM(1;5) mix12mm thick including c/c of all materials and all labour charges etc complete.

Flooring with ceramic tiles 8 to 10mm thick 1st quality non skid floor tiles of scratch free of nano finish of size 600x600mm of IS: 13711,13712,13630 of any colour set over a base coat of CM (1:8) 12mm thick over already laid cement concrete bed including neat cement slurry at 3.30 kgs per sqm and jointing neatly with white cement paste to full depth of slabs laid on already laid cement concrete bed set over base coat of CM (1:8) 12mm thick including neat cement slurry spread at 3.30 kgs per sqm and jointing to full depth of ceramic tiles including cost and conveyance of all materials and labour charges, filling joints neatly, dressing of flooring stones, etc., (IC 7-6)

Providing dadooing to walls with Nano polished /stain free soluble salt porcelain vitrified tiles screen printed of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over base coat of CM(1:5) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete including seigniorage charges etc., complete for finished item of work.

Painting to new walls with two coats of acrylic interior emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade over a base coat of appropriate primer of approved brand, making three coats in all to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete., for finished item of work as per SS 911 for Internal walls (APSS No: 912)

Provision for leach pits ( RCC rings of 1mt dia )

Cost and supply of 1000 mm dia RCC cover slabs

Supplying and Fixing European Water Closet of 1st qualityconformingtoIS:2556-Part-2-1973ofwhiteglazedwith'P'trap including labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS2548-1996 including labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying & Fixing low down porcelain flushing tank 10Lit Capacity with internal componentsincluding labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying&FixingIndianmakeFlatBackWashHandBasin1stqualityconformingtoIS:2556-Part-4:1972withwastefittingslikerubberplug,chain,32mmnominalsize C.P.FittingwithparallelpipethreadconformingtoIS:2963-

Supplying & Fixing white glazed flat back half stall urinals 1st quality conforming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm conforming to IS:2556-Part6, Sec-6-1974 fixed with screws complete Indian make : 410 x 265 x 305 mm

Supplying & Fixing Indian pattern white glazed W.C 1st quality ISI marked conforming to IS:2556Part-3-1981 with"P" or "S" trap: 580 mm Long

Door Frame section of 45x75 MM . Thetwo Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full threadscrews to be used with reverse forward speed control handdrilling machine .Theready/assembled doorframeisfixed to the wall using hold fast or boltfasteners.A minimumof4No.sof screw s to be provided for each verticalmember & minimum 2no.s for horizontalmember.

Providing and fixing 28 -30 MM thicksolidWood Polymer Composite(WPC )single extruded door shutter with 3MMtop and bottom rigid layer with an overalldensity of 750kg/Cum. It will be fixed tothe frame using 3 inch /4 inch hinges. Alluminium of 4 hinges will be required forfixingthe doorwith the frame.

Providing and fixing 28 -30 MM thicksolidWood Polymer Composite(WPC )single extruded door shutter with 3MMtop and bottom rigid layer with an overalldensity of 750kg/Cum. It will be fixed tothe frame using 3 inch /4 inch hinges. Alluminium of 4 hinges will be required forfixingthe doorwith the frame.

Supply, Delivery & Fixing of 20Mm Dia PVC Taps including cost and conveyance fo all the materilas and labour charges etc complete.,

Providing & Placing on Terrace(at all floor levels)polyethylene water storage tank with Double layer approvedbrand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tank labour charges including

Foloowing materials are utilized while fixing the pumpset in;lcude all labour charges etc completed

PVC 110 mm dia 6kg/cm2 pipe

PVC 110 mm dia Bends

Supply and fixing of 1HP Monoblock pumpset includuing cost and conveyance of all charges etc completed

Supply and fixing of 3 core 2.5 sqmm cable wire

UPVC 20 mm dia pipe connections

UPVC20 mm dia gate valves

UPVC20 mm dia couplings

UPVC 20 mm dia FTA

UPVC 20 mm dia ELBOWS

Supply and Fixing of SS Hand Railing

Earth Work excavation and depositing on bank with an initial lead of 10 m and 2 m lift in loamy clayey soils including all labour charges.

Sand filling in basement with watering and tamping including cost and conveyance of all materials and all labour charges etc complete.

CC(1:4:8) mix using 40mm HBG metal including cost and conveyance of all materials and all labour charges etc complete.

Construction of Randam rubble stone masonry in CM(1:6) 2nd sort including cost and conveyance of all materials and labour charges ,seigniorage charges etc complete.

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges. For Square footing

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.Columns Above & below GL

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.For plinth beam

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges. For slab beams

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.Roof slab for 115mm thick

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges. Septic tank bottom slab

Brick Masonry in CM (1:6) with second class non modular or traditional size 23x11x7 cms including cost and conveyance of all materials and labour charges etc., complete for Superstructure

Cost of steel and its fabrication charges incl., bending, cost of binding wire etc., complete as per standard specification

Plastering in CM(1;5) mix12mm thick including c/c of all materials and all labour charges etc complete.

Flooring with ceramic tiles 8 to 10mm thick 1st quality non skid floor tiles of scratch free of nano finish of size 600x600mm of IS: 13711,13712,13630 of any colour set over a base coat of CM (1:8) 12mm thick over already laid cement concrete bed including neat cement slurry at 3.30 kgs per sqm and jointing neatly with white cement paste to full depth of slabs laid on already laid cement concrete bed set over base coat of CM (1:8) 12mm thick including neat cement slurry spread at 3.30 kgs per sqm and jointing to full depth of ceramic tiles including cost and conveyance of all materials and labour charges, filling joints neatly, dressing of flooring stones, etc., (IC 7-6)

Providing dadooing to walls with Nano polished /stain free soluble salt porcelain vitrified tiles screen printed of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over base coat of CM(1:5) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete including seigniorage charges etc., complete for finished item of work.

Painting to new walls with two coats of acrylic interior emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade over a base coat of appropriate primer of approved brand, making three coats in all to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete., for finished item of work as per SS 911 for Internal walls (APSS No: 912)

Supplying and Fixing European Water Closet of 1st quality conforming to IS:2556-Part-2-197 3of whiteglazed with'P' trap including labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS2548-1996 including labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying & Fixing low down porcelain flushing tank 10Lit Capacity with internal componentsincluding labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying & Fixing Indian make Flat Back Wash Hand Basin 1st quality conforming to IS:2556-Part-4:1972 with waste fittings liker ubber plug,chain,32mm nominalsize C.P.Fitting with parallel pipe thread conforming toI S:2963-

Supplying & Fixing Indian pattern white glazed W.C 1st quality ISI marked conforming to IS:2556Part-3-1981 with"P" or "S" trap: 580 mm Long

Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine .Theready/assembled doorframeisfixed to the wall using hold fast or boltfasteners.A minimumof4No.sof screw s to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC )single extruded door shutter with 3MMtop and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed tothe frame using 3 inch /4 inch hinges. Alluminium of 4 hinges will be required for fixing the doorwith the frame.

Supplying and fixing of 90 mm SWR/ PVC pipes (as per ISI standards) 6 Kg/Sq.cm. Prince/sudhakar or any ISI brand and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges etc.complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326)

Supply Delivery & Fixing of S&F 12.7mm N.P bib tap Indian make 3heavy duty sort body including cost and conveyance of all the materilas and labour charges etc complete.,

Providing & Placing on Terrace(at all floor levels)polyethylene water storage tank with Double layer approvedbrand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tank labour charges including ( MAT-01889 BMW-G.01 & LAB-00258 BMW-G.02 )

Stainless Steel Tubes, sections, plates, sheets & pipes of all sizes & diameters for - 304 Grade-For Hand railing

Supply and Transportation of 1.0HP (25x25mm) Single phase Mono block CI body motor pumpset confirms to IS 9079:2002 Makes: As per list of recommended brands as category I

Supply and fixing of 3 core 2.5 sqmm cable wire

Supply and fixing of 16sq.mm WPSC Aluminium service wire

Supply and fixing of 110 mm dia 6kg/cm2 PVC pipe

Supply and fixing of 32 mm dia 10kg/cm2 uPVC pipe

Supply and fixing of cPVC Gum solution ( 250ml )

SINKING OF FILTER POINT :-

Sinking of filter point of 225mm dia with hand driven auger equipment to suitable PVC Casing pipe including cost and conveyence of all materials and labour charges etc., complete

Cost, Supply and Fixing of 225 mm dia PVC 6Kg/Cm2 casing pipe including cost and conveyence of all materials and labour charges etc., complete

Cost, Supply and Transportation of 10.00 HP- 5-10 Stages 5star rated submersible pumpset, confirming to IS 8034 and motor confirming to IS 9283 with water proof winding,Pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415V ± 10% , Three Phase 50 Hz AC supply,etc complete for 6" Bore well.

Cost, Supply and Fixing of 50 mm dia Nominal Bore GI B-Class Pipes medium grade properties & weight as per 1239 ISI mark with GI Fittings including the cost of pipe and its fittings including cost and conveyence of all materials and labour charges etc., complete

Cost, Supply and Run of 3 Core 4.00 Sqmm Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990 including laying charges as per standard specifications .

Fabrication ,transportation and and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. Voltmeter ; 0-500 V 96x96mm size. Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab - 1No 0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size). Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab- 1No Single phase preventor of suitable range Makes: L&T / Minilec / Powertec. - 1No. 32 A TP, 10KA MCB. Makes: Legrand / Schneider / - 1No Indication lamps (R-Y-B) with switch control - 1set Voltmeter & Ammeter selector switch - 2 Nos Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/Havells From 10.00 HP with Automatic Star Delta Starter of Make C&S/Crompton / L&T / Siemens/BCH.

Cost, Supply and Fixing of 225 mm dia PVC Bore Cover including cost and conveyence of all materials and excluding labour charges

Cost, Supply and Fixing of 50 mm dia P.N. 1.60 Heavy duty Non Return Valve including cost and conveyence of all materials and all labour charges etc., complete

Installation and commissioning of 10.00 HP SP Set with all its accessories including transportation of chain block and other necessary equipment and all labour charges etc., complete for finished item of work

PROVIDING PUMPING MAIN

Construction of pipe line for water supply with as per IS:4985/1988, with its amendments and revisions these on including supply of pipes, specials as per requirements, lowering laying and jointing of pipe line with cement solvent true to alignment and gradient, trench excavation for pipe lines in all soils except rock requring blasting, and refilling trenches with excavated earth (other than rocky & and boulders) soils with watering and ramming and removing surplus earth from the pipe line and filling pipe line with required water pressure and testing etc., complete. The rates are including the cost of pipes and cost of specials at 1.20% and excluding the cost of CED. and including cost and conveyance of all materials and labour charges etc., complete

For 110 mm dia P.N.6 PE 100 grade HDPE pipes with trench excavation of size 0.70x1.00 mts including laying and jointing charges

For 100 mm dia DI K7 pipes

Cost, Supply, Delivery and fixing of (P.N.1.60) Tamper Proof DI Flanged Single Chamber Air Release Valves with body & cover made of Ductile Iron Grade GGG-40/SG-400/15 or GGG-50/SG- 500/7 or Equivalent as per IS1865, IS:3896- 2 with Food Grade Epoxy Powder Coating(EP-P) (Min:250 Micron) inside and Outside of Color Blue RAL 5005. All internal parts such as Float, shell, Cove Bolts etc. made of Austenitic alloy steel of SS AISI 304/316 and DN 50 float of and other components with ABS/PTFE/EPDM/NBR and generally conforming to DIN/BIS/AWWA standards (or) combination Flange drilling as per IS - 1538 and exclusive of all taxes and including Transportation, CI air tee of 250x250x80 mm dia, 250 mm CI D/F Pipe 0.60 mts long 2 No.s, 80mm dia CI Pipes 2.00 Mts Long, MTA, MS thereaded flanges, jointing meterials such as bolts nuts and, rubber washers including meterials cost for main line and air valves fixing, labour charges for fixing of CI Pipes and tees and fixing of vlaves, etc., completed.

40 mm dia DI Air Valve P.N.1.60 on 63 mm dia HDPE Pipe line including RCC Valve Chamber

40 mm dia DI Air Valve P.N.1.60 on 100 mm dia HDPE Pipe line including RCC Valve Chamber

Cost, Supply, delivery and Fixing "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG- 400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN- 3202F4/BS:5163 Type A Flange drilling as per IS - 1538 excluding all taxes, duties and transportation including DI Flanged sockets, jointing meterials such as bolts nuts and rubber washers including meterials cost for main line labour charges for Flanged Joints and Lowering of valves, etc., completed.

100mm dia DI Sluice Valves P.N.1.60 on 110 mm dia HDPE Pipe lines

CONSTRUCTION OF VALVE CHAMBER

Earthwork excavation and depositing on bank with initial lead and lift in all soils including cost and conveyence of all materials and all labour charges etc., complete

Plain Cement Concrete (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete

Reinforced Cement Concrete (1:1.5:3) using 10mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete

For side walls alround

For precast top slab 100 mm dia

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 415 grade as per IS 1786-1985) of 8mm to 40mm diameters, cutting, bending, to required sizes and shapes placing in position with cover blocks of approved size and binding wire of 20SWG, forming grills for reinforcement work as per approved designs and drawings including cost and conveyance of bars from approved sources to site of work, including cost and conveyance of binding wire, cover blocks, chairs, overlaps, spacers, dowels, wastage etc., and all operational, incidental, and labour charges such as cutting, bending, placing in position, tying etc., and sales & other taxes,on cost of all materials complete for finished item of work.

Construction of Sump

Earthwork excavation in all soils with initial lead and lift including cost and conveyence of all materials and all labour charges etc., complete 1st Mattu

Earthwork excavation in all soils with initial lead and lift including cost and conveyence of all materials and all labour charges etc., complete 2nd Mattu

Plain Cement Concrete (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete

Supply and filling of Local Sand including cost and convenyance of all material and all labour charges etc. complete as per standard specifications. Clause 305.3.9 MORD & 304 MORTH

M30 Grade Concrete using 20 mm HBG Metal including cost and conveyence of alll materials and labour charges etc,,complete for Bottom Raft

M30 Grade Concrete using 20 mm HBG Metal including cost and conveyence of alll materials and labour charges etc,,complete for Side Walls

M30 Grade Concrete using 20 mm HBG Metal including cost and conveyence of alll materials and labour charges etc,,complete for Top Slab 0.15 mm thickness

Accoproof Plastering with CM /(1:3) 12 mm thick including cost and conveyence of alll materials and labour charges etc,,complete

Cement Plastering with CM /(1:3) 12 mm thick including cost and conveyence of alll materials and labour charges etc,,complete

Snowcem Painting including cost and conveyence of alll materials and labour charges etc,,complete

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 415 grade as per IS 1786-1985) of 8mm to 40mm diameters, cutting, bending, to required sizes and shapes placing in position with cover blocks of approved size and binding wire of 20SWG, forming grills for reinforcement work as per approved designs and drawings including cost and conveyance of bars from approved sources to site of work, including cost and conveyance of binding wire, cover blocks, chairs, overlaps, spacers, dowels, wastage etc., and all operational, incidental, and labour charges such as cutting, bending, placing in position, tying etc., and sales & other taxes,on cost of all materials complete for finished item of work.

Supply of Manhole Covers including cost and conveyence of alll materials and labour charges etc,,complete

DRILLING OF BOREWELL:-

Drilling of 165 mm dia Bore well with power rig including flushing to the clear in all starta ,hard rock loose soil, inserting 175 mm dia MS casing pipe etc. complete Up to 90.00 Mts

Cost, Supply and Fixing of 225 mm dia PVC 6Kg/Cm2 extra casing pipe for borewells for potable water supply conforming to IS: 4985/2000 and amendments from time to time including transportation etc., complete

Geologist Charges for Borewell

Cost, Supply and Transportation of 7.50 HP- 5 Stages 5star rated submersible pumpset, confirming to IS 8034 and motor confirming to IS 9283 with water proof winding,Pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415V ± 10% , Three Phase 50 Hz AC supply,etc complete for 6" Bore well.

Fabrication ,transportation and and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. Voltmeter ; 0-500 V 96x96mm size. Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab - 1No 0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size). Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab- 1No Single phase preventor of suitable range Makes: L&T / Minilec / Powertec. - 1No. 32 A TP, 10KA MCB. Makes: Legrand / Schneider / - 1No Indication lamps (R-Y-B) with switch control - 1set Voltmeter & Ammeter selector switch - 2 Nos Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/Havells From 7.50 HP with Automatic Star Delta Starter of Make C&S/Crompton / L&T / Siemens/BCH.

Cost, Supply and Fixing of 50 mm dia GI 'B' Class Pipes including cost of specials and conveyence of all materials etc., complete

Cost, Supply and Fixing of 65 mm dia GI 'B' Class Pipeline including cost of specials and conveyence of all materials and labour charges etc., complete

Cost, Supply and Run of 3 Core 4.00 Sqmm Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990 including laying charges as per standard specifications .

Cost, Supply and Fixing of Gun Metal Non Return Valve including cost and conveyenc eof all materials and all labour charges etc., complete

Earth Work excavation of trench size 0.70x1.00 Mts in O.G.Soils ture to alignment and gradient for 90 mm dia at 6Kg/Cm2 PVC Pipeline and refilling the trench with excavated earth including cost and conveyance of all labour charges etc., complete with 2/3rd Machinary and 1/3rd Manual Etc., complete

Earth Work excavation of trench size 0.70x1.00 Mts in O.G.Soils ture to alignment and gradient for 110 mm dia at 6Kg/Cm2 PVC Pipeline and refilling the trench with excavated earth including cost and conveyance of all labour charges etc., complete with Manual Etc., complete

Earth Work excavation of trench size 0.70x1.00 Mts in O.G.Soils ture to alignment and gradient for 90 mm dia at 6Kg/Cm2 PVC Pipeline and refilling the trench with excavated earth including cost and conveyance of all labour charges etc., complete with Manual Etc., complete

Cost, Supply and Fixing of 65 mm dia GI 'B' Class Pipes including cost of specials and conveyence of all materials and labour charges etc., complete

Cutting open C.C.road surface with concrete saw cutter and removal with breaker including stacking of excavated materials for pipeline trench work including labour charges, all leads, lifts and conveyance of all materials etc., complete as directed by the deparmental officers.

Supply, delivery, laying and Jointing of Single Chamber DI Air Valve ( PN 1.60) with Body and cover in Ductile Iron of grade SG 400/12 or equivalent grade as per I.S.3896-part2-1985 and subsequent revisions. All internal parts such as float, shell etc., all cover bolts, of stainless steel, and Gaskets and seals of EPDM food grade quality Epoxy powder coating (EP-P) inside and outside colour blue. Drilled as per IS:1538 on pipe line including supply of Air valve ,CI Specials to suit the pressure class of pipe etc.complete as specified in Technical specifications in (PartB - Volume I) drawing in (Part C - Volume 1). The rates are inclusive of cost and conveyance of all materials & specials and construction of RCC valve chambers as per requirement with RCC slab and RCC manhole cover with locking arrangements etc.complete for finished item of work , but excluding GST . 80 mm dia PN 1.6 Air Valves on 250 mm dia Pipeline

Supply, delivery, laying and Jointing of Single Chamber DI Air Valve ( PN 1.60) with Body and cover in Ductile Iron of grade SG 400/12 or equivalent grade as per I.S.3896-part2-1985 and subsequent revisions. All internal parts such as float, shell etc., all cover bolts, of stainless steel, and Gaskets and seals of EPDM food grade quality Epoxy powder coating (EP-P) inside and outside colour blue. Drilled as per IS:1538 on pipe line including supply of Air valve ,CI Specials to suit the pressure class of pipe etc.complete as specified in Technical specifications in (PartB - Volume I) drawing in (Part C - Volume 1). The rates are inclusive of cost and conveyance of all materials & specials and construction of RCC valve chambers as per requirement with RCC slab and RCC manhole cover with locking arrangements etc.complete for finished item of work , but excluding GST . 50 mm dia PN 1.6 Air Valves on 200 mm dia Pipeline

Supply, delivery, laying and Jointing of Single Chamber DI Air Valve ( PN 1.60) with Body and cover in Ductile Iron of grade SG 400/12 or equivalent grade as per I.S.3896-part2-1985 and subsequent revisions. All internal parts such as float, shell etc., all cover bolts, of stainless steel, and Gaskets and seals of EPDM food grade quality Epoxy powder coating (EP-P) inside and outside colour blue. Drilled as per IS:1538 on pipe line including supply of Air valve ,CI Specials to suit the pressure class of pipe etc.complete as specified in Technical specifications in (PartB - Volume I) drawing in (Part C - Volume 1). The rates are inclusive of cost and conveyance of all materials & specials and construction of RCC valve chambers as per requirement with RCC slab and RCC manhole cover with locking arrangements etc.complete for finished item of work , but excluding GST . 100 mm dia PN 1.6 Air Valves on 110 mm dia Pipeline

Supply, delivery, laying and Jointing of Single Chamber DI Air Valve ( PN 1.60) with Body and cover in Ductile Iron of grade SG 400/12 or equivalent grade as per I.S.3896-part2-1985 and subsequent revisions. All internal parts such as float, shell etc., all cover bolts, of stainless steel, and Gaskets and seals of EPDM food grade quality Epoxy powder coating (EP-P) inside and outside colour blue. Drilled as per IS:1538 on pipe line including supply of Air valve ,CI Specials to suit the pressure class of pipe etc.complete as specified in Technical specifications in (PartB - Volume I) drawing in (Part C - Volume 1). The rates are inclusive of cost and conveyance of all materials & specials and construction of RCC valve chambers as per requirement with RCC slab and RCC manhole cover with locking arrangements etc.complete for finished item of work , but excluding GST . 40 mm dia PN 1.6 Air Valves on 90 mm dia Pipeline

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves PN 1.6 (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 including all taxes, duties , complete and lowering, laying and fixing the valve in the pipeline including necessary specials, jointing materials, etc., including construction of RCC valve chamber of departmental approved size as per the design and drawings, etc.complete for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges and all taxes, duties and levies for finished item of work, but excluding GST for Pumping mains. 200 mm dia Sluice valves on 200 mm dia DI Pipeline

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves PN 1.6 (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 including all taxes, duties , complete and lowering, laying and fixing the valve in the pipeline including necessary specials, jointing materials, etc., including construction of RCC valve chamber of departmental approved size as per the design and drawings, etc.complete for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges and all taxes, duties and levies for finished item of work, but excluding GST for Pumping mains. 100 mm dia Sluice valves on 110 mm dia PVC Pipeline

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves PN 1.6 (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 including all taxes, duties , complete and lowering, laying and fixing the valve in the pipeline including necessary specials, jointing materials, etc., including construction of RCC valve chamber of departmental approved size as per the design and drawings, etc.complete for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges and all taxes, duties and levies for finished item of work, but excluding GST for Pumping mains. 80 mm dia Sluice valves on 90 mm dia PVC Pipeline

Cost, Supply and Fixing of CI 200 mm dia Class-B Pipes including cost of specials and conveyence of all materials etc., complete

Cost, Supply and Fixing of CI 80 mm dia Class-B Pipes including cost of specials and conveyence of all materials etc., complete

Cost, Supply and Fixing of Bolts & Nuts including cost and conveyence of all materials etc., complete

Cost, Supply and Fixing of Rubber Packing including cost and conveyence of all materials etc., complete

Providing Ornamental Grill including Structural Steel and Welding charges including cost and conveyence of all materials and labour charges etc., complete

White washing in two coats with white cement to give and even shade after throughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance all materials and all labour charges etc complete., and Painting with snowcem are other equal and approved water proof cement paint two coats over priming coat including cost and conveyance of all materials and all labour charges etc., complete.

Providing Fencing For Transformer and CT-PT meter, Earthing for Pump House and Internal Lighting in Head Works Dozer (D 50) for clearing the site in head works including all labour charges etc., complete

Earth Work excavation and depositing on bank with an initial lead of 10 m and 2 m lift in loamy clayey soils including all labour charges.

Brick Masonry in superstructure with CM (1:6) prop: using Flyash bricks of size (290x225x140) from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, including seigniorage charges, & other taxes on all materials, all operational, incidental and labour charges such as mixing cement mortar, constructing masonry, scaffolding charges, lift charges, curing, etc., complete for finished item of work.

Cement Plastering 12mm thick in CM (1:5) dubara sponge finish including cost and conveyance of all materials like cement, sand, water etc., to site, seigniorage charges, sales & other taxes on all materials,all operational, incidental and labour charges such as mixing mortar, scaffolding charges, lift charges, including cutting of Grooves wherever necessary as directed by Engineer - in - charge, finishing, curing, etc., complete for Even Surfaces of Wall for finished item of work. (APSS 901,903 & 904) inside & outside

Cement Concrete ( 1:2:4) using 20 mm HBG crushed metal including cost and conveyance of all materials and all labour charges etc complete.

Spreading of 40 mm HBG metal of including cost and conveyance of all materials and all labour charges etc complete.

Providing Independent earthing for important equipment with 100 mm dia Heavy guage C.I. (Cast Iron) pipe with flange 2.5m long enclosed in CC Brick masonry chamber of 450X450X400 mm with RCC Slab cover duly providing staggered holes filling with salt and charcoal from the bttom of the pipe giving earth connection from electrode through G.I. strip of 40X6X200 mm length will all accessories and labour charges etc., complete

Supply and Fixing of MS Structural Steel like plates including welding charges, including cost and conveyance of all materials and all labour charges etc complete.

Supply and transportation of 150 W LED Street light Luminaire made of pressure diecast alluminium body with powder coated, having protective toughned glass, Supply Input voltage 120 - 270 V AC, P.F > 0.90, high power LED's having System efficacy > 95 lm/W and junction temprature < 70°C, with Ingrees protection IP65, Luminaire performance complies to IS 10322 (Part 5 / Sec-3), Driver surge protection 4KV, external Surge protection ≥ 5KV with optics distribution etc., complete

Supply and transportation of 2C X 1.50 sqmm XLPE/PVC insulated & PVC sheathed armoured cables of 1.1 KV grade with copper conductor as per IS:7098 Part-I-1988 with all accessories including labour charges etc., complete

Earth Work excavation and depositing on bank with an initial lead of 10 m and 2 m lift in loamy clayey soils including all labour charges.

Cement Concrete ( 1:2:4) using 20 mm HBG crushed metal including cost and conveyance of all materials and all labour charges etc complete.

Lifting of existing Shud and transporting to other location by using crane of capacity of 3 tonnes including cost and conveyance of all materials and all labour charges etc complete.

Cutting open C.C.road surface with concrete saw cutter and removal with breaker including stacking of excavated materials for pipeline trench work including labour charges, all leads, lifts and conveyance of all materials etc., complete as directed by the deparmental officers.

Supply and Fixing of MS Structural Steel like plates including welding charges, including cost and conveyance of all materials and all labour charges etc complete.

Supply of 1200 mm (48") sweep 230V, A.C 50 Hz.Ceiling Fan with 3 Blades and double ball bearings with all standard accessories.etc., complete

Supply of 36/40 W Box tipe tube light luminaire powder coated CRCA Sheet stell housing with electranic ballast chokes and all standard accessories etc., complete asper standard specifications

Providing and placing on terrace (at all floor levels) polyetheylene water storage tank with double layer approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet and outlets and over flow pipes but without fittings and base support for tanks including cost and conveyance of all materials and labour charges etc.,complete

Supply and fixing of Pedastal for wash hand basin etc., complete asper standard specifications

Cost of Labour charges of Pedastal for wash hand basin etc., complete asper standard specifications

Earth Work excavation and depositing on bank with an initial lead of 10 m and 2 m lift in loamy clayey soils including all labour charges.

Cement Concrete ( 1:2:4) using 20 mm HBG crushed metal including cost and conveyance of all materials and all labour charges etc complete.

Providing , laying, testing Commissioning of following classes MS pipesconforming to IS 3589 and 1239 including fittings like elbows, tees,flanges, tapers, nuts, bolts, gaskets etc., complete. Makes : As per list of recommended brands. For 250mm dia MS pipe

Providing Ornamental Grill including Structural Steel and Welding charges including cost and conveyence of all materials and labour charges etc., complete

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves PN 1.6 (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 including all taxes, duties , complete and lowering, laying and fixing the valve in the pipeline including necessary specials, jointing materials, etc., including construction of RCC valve chamber of departmental approved size as per the design and drawings, etc.complete for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges and all taxes, duties and levies for finished item of work, but excluding GST for Pumping mains. 80 mm dia Sluice valves on 80 mm dia DI Pipeline

Earth Work excavation and depositing on bank with an initial lead of 10 m and 2 m lift in loamy clayey soils including all labour charges.

Sand filling in basement with watering and tamping including cost and conveyance of all materials and all labour charges etc complete.

CC(1:4:8) mix using 40mm HBG metal including cost and conveyance of all materials and all labour charges etc complete.

Construction of Randam rubble stone masonry in CM(1:6) 2nd sort including cost and conveyance of all materials and labour charges ,seigniorage charges etc complete.

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges. For Square footing

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.Columns Above & below GL

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.For plinth beam

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges. For slab beams

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges.Roof slab for 115mm thick

Reinforced Cement concrete (1:2:4) M 20 grade using 20 mm HBG chips including cost and conveyance of all materials and all labour charges etc.but excluding cost of steel and its fabrication charges. Septic tank bottom slab

Brick Masonry in CM (1:6) with second class non modular or traditional size 23x11x7 cms including cost and conveyance of all materials and labour charges etc., complete for Superstructure

Cost of steel and its fabrication charges incl., bending, cost of binding wire etc., complete as per standard specification

Plastering in CM(1;5) mix12mm thick including c/c of all materials and all labour charges etc complete.

Flooring with ceramic tiles 8 to 10mm thick 1st quality non skid floor tiles of scratch free of nano finish of size 600x600mm of IS: 13711,13712,13630 of any colour set over a base coat of CM (1:8) 12mm thick over already laid cement concrete bed including neat cement slurry at 3.30 kgs per sqm and jointing neatly with white cement paste to full depth of slabs laid on already laid cement concrete bed set over base coat of CM (1:8) 12mm thick including neat cement slurry spread at 3.30 kgs per sqm and jointing to full depth of ceramic tiles including cost and conveyance of all materials and labour charges, filling joints neatly, dressing of flooring stones, etc., (IC 7-6)

Providing dadooing to walls with Nano polished /stain free soluble salt porcelain vitrified tiles screen printed of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over base coat of CM(1:5) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete including seigniorage charges etc., complete for finished item of work.

Painting to new walls with two coats of acrylic interior emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade over a base coat of appropriate primer of approved brand, making three coats in all to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete., for finished item of work as per SS 911 for Internal walls (APSS No: 912)

Supplying and Fixing European Water Closet of 1st quality conforming to IS:2556-Part-2-197 3of whiteglazed with'P' trap including labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS2548-1996 including labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying & Fixing low down porcelain flushing tank 10Lit Capacity with internal componentsincluding labour charges only for fixing European Water Closet with'P'or 'S' trap as per standard practice

Supplying & Fixing Indian make Flat Back Wash Hand Basin 1st quality conforming to IS:2556-Part-4:1972 with waste fittings liker ubber plug,chain,32mm nominalsize C.P.Fitting with parallel pipe thread conforming toI S:2963-

Supplying & Fixing Indian pattern white glazed W.C 1st quality ISI marked conforming to IS:2556Part-3-1981 with"P" or "S" trap: 580 mm Long

Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine .Theready/assembled doorframeisfixed to the wall using hold fast or boltfasteners.A minimumof4No.sof screw s to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC )single extruded door shutter with 3MMtop and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed tothe frame using 3 inch /4 inch hinges. Alluminium of 4 hinges will be required for fixing the doorwith the frame.

Supplying and fixing of 90 mm SWR/ PVC pipes (as per ISI standards) 6 Kg/Sq.cm. Prince/sudhakar or any ISI brand and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges etc.complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326)

Supply Delivery & Fixing of S&F 12.7mm N.P bib tap Indian make 3heavy duty sort body including cost and conveyance of all the materilas and labour charges etc complete.,

Providing & Placing on Terrace(at all floor levels)polyethylene water storage tank with Double layer approvedbrand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tank labour charges including ( MAT-01889 BMW-G.01 & LAB-00258 BMW-G.02 )

Stainless Steel Tubes, sections, plates, sheets & pipes of all sizes & diameters for - 304 Grade-For Hand railing

Supply and Transportation of 1.0HP (25x25mm) Single phase Mono block CI body motor pumpset confirms to IS 9079:2002 Makes: As per list of recommended brands as category I

Supply and fixing of 3 core 2.5 sqmm cable wire

Supply and fixing of 16sq.mm WPSC Aluminium service wire

Supply and fixing of 110 mm dia 6kg/cm2 PVC pipe

Supply and fixing of 32 mm dia 10kg/cm2 uPVC pipe

Supply and fixing of cPVC Gum solution ( 250ml )