Construction work of New Control Building at Deo Dam, TaHalol, Dist: Panchamahal

Construction work of New Control Building at Deo Dam, Ta-Halol, Dist: Panchamahal

BILL OF QUANTITIES

Percentage Rate Tender

Item Description of Item Quantity Unit Rate In Amount

1 Excavation for foundation upto 1.5 m depth including sorting out and 124.19 Cu.m. 264.82

stacking of useful materials and disposing off the excavated stuff upto

50 Meter lead.Soft rock not requiring Blasting

2 Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse 44.55 Cu.m. 2980.90

sand : 6- hand broken stone aggregates 40 mmnominal size) and

curing complete excluding cost of formwork in (A) Foundation and

3 Providing and laying controlled cement concrete M.250 and curing 17.52 Cu.m. 4743.97

complete including the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in (A) Foundations,

footings, Base of columns and Mass concrete. (upto 10 ton)

4 Providing and laying controlled cement concrete M.250 and curing 8.67 Cu.m. 8522.38

complete including the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in (D) Columns, Pillars

posts and struts, upto floor two level. (upto 10 ton)

5 Filling available excavated earth (excluding rock) in 26.73 Cu.m. 130.39

trenches. plinth, sides of foundations etc. in layers not exceeding

cm. in depth consolidating each disposited layer by ramming

6 Providing and laying controlled cement concrete M.250 and curing 24.25 Cu.m. 7284.12

complete including the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in (C)

Slabs,landing,shelves,Balconies, Lintels, Beams, Girders and

Cantilever upto floor two level. (upto 10 ton)

7 Brick work using common burnt clay building bricks having crushing 28.67 Cu.m. 4021.02

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto

8 Filling in foundation and plinth with murrum or selected soil in layers 60.85 Cu.m. 273.96

of 20cm. thickness including watering, ramming and consolidating

etc. complete. (upto 10 ton)

9 Brick work using common burnt clay building bricks having crushing 62.61 Cu.m. 4289.33

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto

10 ton) Extra for brick work in superstructure above plinth level upto

floor two level (B) Conventional

10 (i) Half brick masonry in common brunt clay building bricks having 8.50 Sq.m. 651.67

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional

Extra for half brick masonry in superstructure above plinth level upto

floor two level. (B) Conventional

11 Providing and laying controlled cement concrete M.250 and curing 19.22 Cu.m. 6128.68

complete including the cost of formwork and reinforcement for

reinforced concrete work in (C) Slabs,landing,shelves,Balconies,

Lintels, Beams, Girders and Cantilever upto floor two level. (upto

10 ton) For Ground Floor

12 Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2- 0.94 Cu.m. 10219.39

coarse sand : 4- graded stone aggregates 20 mm nominal size) for

R.C.C lintel including finishing smooth with,curing etc. complete

including the cost of formwork but excluding the cost of

reinforcement.Ground Floor

13 Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse 0.38 Cu.m. 6437.85

sand : 4- graded stone aggregates 20 mm nominal size) for reinforced

concrete Chhajjas not exceeding 10cm. thickness upto floor two level

including finishing the exposed surfaces with cement mortar 1:3 (1-

cement, 3 Fine sand) to give a smooth and even surface centering and

formwork and curing complete excluding cost of

reinforcement.Ground Floor

14 Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse 3.47 Cu.m. 3925.77

sand : 6- crushed stone aggregates 20 mm nominal size) and curing

complete including cost of formwork in (A)Wall Caps / Coping

15 Providing and laying controlled cement concrete M.200 and curing 1.90 Cu.m. 6843.76

complete including the cost of formwork and reinforcement for

reinforced concrete work in GF Staircase

16 Providing TMT Bar FE 500D reinforcement for R.C.C. work 8104.58 Kg. 76.21

including bending, binding and placing in position complete upto

floor two level.Ground Floor & First Floor

17 20mm thick sand faced cement plaster on walls upto height 10 metres 341.49 Sq.m. 329.29

above ground level consisting of 12mm thick backing coat of C.M.

1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-

cement : 1-sand) etc. complete.

18 Providing 15mm thick cement plaster in single coat on Rough 352.03 Sq.m. 167.03

(Similar)side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (ii) Cement mortar

1:4 (1-cement :4-sand)

19 Providing 15mm thick cement plaster in single coat on Rough 141.60 Sq.m. 167.24

(Similar)side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (ii) Cement mortar

1:4 (1-cement :4-sand) For Ground Floor Ceiling

20 Applying 2 coat of Primer Coat of approved brands on exterior 341.49 Sq.m. 50.50

surface with proper cleaning etc. Item to be approved by engineer

incharge or consulting engineer

21 Finishing wall with weather proof exterior emulsion paint on wall 341.49 Sq.m. 114.53

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains of

loose powdered materials.etc complete

22 Applying two coats of putty & two coats of primer of approved brand 352.03 Sq.m. 40.59

and manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and other

foreign matter and sand papered smooth.

23 Wall painting (two coats) with plastic emulsion paint of approved 352.03 Sq.m. 78.90

brand and manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from mortar

droppings and other foreign matter and sand papered smooth.

24 Providing and laying Machine cut free edges machine polished 51.70 Sq.m. 3193.62

telephone black madras Granite stone slab 18mm (Average ) thick (

Single Piece not more than 150cm) for stair steps and risers &

Door/window frame as per design including full moulded round front

steps & 1cm nosing & necessary groove on trads of steps ;laid on

20mm thick cement mortar 1:6 ( 1 cement : 6 coarse sand ) jointed

with gray cement sluury including rubbing and polsihing etc.

25 Providing and Fixing flush door both side laminated & I.T.W. beading 13.76 Sq.m. 2847.84

all around by using I.T.W. frame 120 mmX 80 mm shutter fabricated

from 35 mm thick solid core malemine faced three layered pre

laminated flat pressed wood based exterior grade bonded BWP/BWR

synthetic resin having stamped IS 12823 grade I type II including

three coats of lacquer polishing to exposed wooden surface &

stainless steel decorative type designs fixtures/ fastening etc including

I.T.W trinagular batten patti of size 30mm X 30mm etc as per

architectural detailed drawing & as directed by engineer incharge.

26 Providing and Fixing 30mm thick factory made solid panel PVC door 1.58 Sq.m. 2605.15

shutter consisting of frame made out of M.S. tubes of 19 gauge

thickness and size of 19mm x 19mm for stiles and 15mm x 15 mm for

top and bottom rails. M.S. frame shall have a coat of steel primers of

approved make and manufacture, M.S. frame shall be covered with

mm thick heat moulded PVC ‘C’ channel of size 30 x 50 mm forming

stiles, and 5mm thick 75mm wide PVC sheets for top rail, lock rail

and bottom rail on either side, and 10mm (5mm x 2) thick, 20mm

wide cross PVC sheet as gap insert for top rail and bottom rail,

Panelling of 5 stiles and rails with 30mm wide x 5mm thick PVC

sheet beading on eighter side, and joined together with solvent cement

adhesive,. An additional 5mm thick PVC strip of 20mm width is to be

stculk on the interior side of the ‘c’ channel using PVC solvent

cement adhesive etc. complete as per direction of Engineer in charge,

manufacture’s specification and drawing.

27 Providing and fixing window having extruded aluminum Colour 14.40 Sq.m. 1583.95

anodized section frame main outer size 95mm x 24mm x 1.17mm (of

Jindal Section no:2459 @ wt.of 0.738 Kg/mt), horizontal Three track

member size 92mm x 31.75mm x 1.30mm (of Jindal Section

no:8688,@ Wt.1.07 Kg/mt), vertical member of size 92mm x

31.75mm x 1.50mm (of Jindal Section no:8933,@ Wt. 1.06 Kg/mt)

with sliding shutters of horizontal member size 40 mmx18mm

x1.29mm (of Jindal Section no:8947@ wt.of 0.456 Kg/mt), vertical

member of size 40mm x 18mm x 1.29 mm (of Jindal Section no:8949

@ wt.of 0.456Kg/mt/ with 5 mm thick transparent bronze colour

tinted float glass with powder coated aluminum fittings and fixtures

and transparent silicon sealant glass fixing to frame as per details etc

28 Providing and fixing standared extruded of alluminium section of size 0.72 Sq.m. 1175.56

63mm x 38.10mm x 1.2mm (Jindal Section :2434, @ Wt.

Kg/mt) with colour anodized alluminium frame for ventilation with

mm thick frosted glass as details etc complete for Ventilation

29 Providing and fixing M.S. grills of required pattern to wooden frames 453.60 Kg. 102.62

of windows etc. with M.S. flats at required spacings and frame

alround, square or round bars with round headed bolts and nuts or by

screws (A) Plain Grill. (upto 10 ton)

30 Painting two coats (excluding priming coat) on new steel and other 15.12 Sq.m. 95.95

metal surface with enamel paint, brushing, interior to give an even

shade including cleaning the surface an even shade including cleanicn

the surface of all dirt, dust and other foreign matter.

31 Providing and fixing 90 cm high Stainless steel railing made from 33.10 Rmt. 3346.13

anticorrocive S S pipe of 50 mm dia (16Gauge) as hand rail with S S

38 mm dia (16Gauge) as a vertical support fixed in RCC slab at 1.2m

c/c including three horizontal S S pipes of 16 mm dia (16Gauge) at

eqal distance fixed by 18.75 mm dia (16Gauge) S S pipe including

accessories as per detailed drawing as directed etc. complete.

32 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm 237.61 Sq.m. 1334.64

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface

etc.complete for light shade

33 Providing and laying coloured glazed tiles of the size 300 mm x 200 30.30 Sq.m. 1417.36

mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps

and dedo on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse

sand) & jointed with white cement slurry.

34 Providing and laying broken chine mosaic flooring over avg 40 143.49 Sq.m. 1030.44

mm C.C 1:2:4 bedding for maintaning slope for plain and curve

surface & 12 mm to 20 mm broken pieces of glazed tiles to be laid

over cement mortar 1:3 to plain or slope and to be tempered to

bring mortar creme out upto surface using white cement including

rounding off junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed. Providing

and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand :

4-graded stone aggregate 20mm nominal size) laid in one layer and

finished with a floating coat of neat cement. (A) 40mm thick. (upto

35 Providing 0.75mt wide plinth protection including excavation in hard 58.71 Rmt. 987.64

or dence soil and Laying C.C 1:3:6 (1 cement : 3 coarse sand:

brickbats/stone aggregates) in foundation and on top including

Curring fnishng etc. complete.

36 Providing cement vata (10cm. x 10 cm. size) quarter round in cement 80.66 Rmt. 23.68

mortar 1:1 including neat cement finishing, watering etc. complete.

37 Providing and fixing wsh down water closet wall hung matte finish 1.00 Each 10100.00

outside and glossy inside (European type, W.C. Pan) make

cera/hindware/Kohler/Jaquar etc or similar with integral P or S trap

including jointing the trap with soil pipe in Cement Mortar 1:1 (1-

Cement : 1-fine sand) with Seal and cover of size 510X365X380 mm.

Item to be approved by engineer incharge or consulting engineer

38 Providing erecting and fixing double coated Syntex PVC. (ISI) water 1000.00 Ltr. 3.95

tank of required capacity each with all necessary fittings and

connection etc. complete on terrace.

39 Providing and fixing thin rim table top washbasin with single hole for 1.00 Each 9257.64

pillar tap with C.I. or M.S. brackets painted white including sutting

holes and making good the same but excluding fittings.(A) Vitreous

China:(ii) Flat Back washbasin 550 mm x 380mm size x 110 mm. (i)

In white colour.a)Providing and fixing C.P. brass waste for washbasin

or sink. (A) 32mmdia. b)Providing and fixing M.I. fisher union for

washbasin or sink. (A) 32mm dia. c)Providing and fixing pillar tap,

capstan head, screw down high pressure with screws, shanks and

back nuts. (i) 15mm dia.d)Providing and fixing brass screw down

stop tap.(A) 15mm dia.e)Providing and fixing Rubber plug for sink or

40 Providing and fixing washbasin with single hole for pillar tap with 1.00 Each 2060.73

C.I. or M.S. brackets painted white including sutting holes and

making good the same but excluding fittings.(A) Vitreous China:(ii)

Flat Back washbasin 550 mm x v 400mm size. (i) In white

colour.a)Providing and fixing C.P. brass waste for washbasin or sink.

(A) 32mmdia. b)Providing and fixing M.I. fisher union for washbasin

or sink. (A) 32mm dia. c)Providing and fixing pillar tap, capstan

head, screw down high pressure with screws, shanks and back nuts.

(i) 15mm dia.d)Providing and fixing brass screw down stop tap.(A)

15mm dia.e)Providing and fixing Rubber plug for sink or wash basin.

41 Providing and fixing 600mm x 450mm bevelled edge mirrror of 2.00 Nos. 833.73

superior glass mounted on 6mm thick A.C. sheet or plywood sheet

and fixing to wooden pluge with C.P. brass screws and washers.

42 Providing and fixing C.P. brass towel rail comlete with C.P. brass 2.00 Nos. 616.42

brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x

43 Providing and fixing C.P. brass shower rose with 15mm or 20mm 1.00 Nos. 282.16

inlet.(A) 100mm dia. Each

44 Providing and fixing soap dish holder 2.00 Each 707.00

45 Providing and fixing soap dispenser with glass bottle 2.00 Each 1464.50

46 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 4.00 Each 558.36

mm diameter with jali of the following nominal diameter of self

cleansing design with C.I scread down or hinged grating including the

cost of cutting and making good the walls.

47 Providing and fixing screw down bib taps of following size.(A) Brass 4.00 Each 186.83

screw down bib tap polished bright. (ii) 15mm dia.

48 Providing and fixing pillar tap, capstan head, screw down high 2.00 Each 308.73

pressure with screws, shanks and back nuts. (ii) 15mm dia.

49 Providing and fixing chromium plated brass half trun flush cock of 2.00 Each 254.78

approved quality including fixing in pipe line etc. complete.(i) 20mm

50 Providing and fixing 100mm size P or S trap for water closet squatting 2.00 Each 329.29

pan including jointing the trap with the pan and soil pipe in cement

Mortar 1:1 (1 Cement : 1-Fine sand)(A) Vitreous China.

51 Providing and fixing water closet squatting Pan (Indian type W.C. 1.00 Each 948.09

Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be

measured and paid for separately) (A) Vitreous China.(I) Long pattern

52 Providing and fixing in position cowel went to pipes.(B) 75mm dia. 2.00 Nos. 389.74

53 Providing laying and jointing in true line and level 15mm dia. 20.00 Rmt. 72.65

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make

PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be fixed on the wall with

the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent, including cost of all

54 Providing laying and jointing in true line and level 25mm dia. 25.00 Rmt. 91.84

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make

PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be fixed on the wall with

the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent, including cost of all

55 Providing laying and jointing in true line and level 40mm dia. 30.00 Rmt. 148.12

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make

PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be fixed on the wall with

the help of clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent, including cost of all

56 Providing and fixing concealed center point to wall ceiling & floor 5.00 Rmt. 166.86

CPVC (SDR 13.5) PIPE having National Sanitation Foundation

(NSF) seal for potable water of following dia. nominal bore tube

fittings and clamps including making good the wall, ceiling and floor

etc. complete.[A] 15 mm.

57 Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working 15.00 Rmt. 213.11

pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor 75 mm Dia

58 Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working 34.20 Rmt. 334.31

pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor 110 mm Dia

59 Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working 5.00 Rmt. 707.00

pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor 160 mm Dia

60 Providing Sandwitch Type Kitchen Platform Using 25mm thick 3.55 Rmt. 3764.27

Single Polished kotah stone 75 cm Width at Top Width 16 to 18 mm

Thick Premium Black Grenite Stone at Top with 75 mm Width and

Face Patta Maximum 3.0 Mtr Long In Single Piece using Cement

Mortar 1:4 ( 1 cement : 4 coarse sand ) laid by 75 cm width & 75 cm

High Resting On 25 mm Thick One Side Polished kotah stone fixed in

wallc Cement Mortar 1:4 ( 1 cement : 4 sand ) at Bottom Polished

Kotah stone flooring including fixing grenite stone & cutting the stone

for Fixing Kitchen Sink with Polished & Including Providing

Premium Black Polished Grenite Stone 16 to 18 mm Thick with round

Border the edge,cost of S.S Kitchen sink. S S Grating Jali for nahni

Trap, Brass Waste Coupline ,PVC Waste Pipe, Manking Grove in

Tile & Wall for Flooring Kotah Stone & Granite ....etc.Complete as

per Drawing & Directed by Engineer in charge or consulting engineer

61 Providing and fixing Kitchen sink make cera/hindware/Kohler/Jaquar 1.00 Nos. 2958.63

etc or similar with C.I. or M.S. brackets, painted white including

cutting holes in walls and making good the same . (C) Vitreous China

Sink.(i) 600mm x 450mm x 150mm size.with fittings(ii) Flat Back

washbasin 550 mm x v 400mm size. (i) In white colour.a)Providing

and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

b)Providing and fixing M.I. fisher union for washbasin or sink. (A)

32mm dia. c)Providing and fixing pillar tap, capstan head, screw

down high pressure with screws, shanks and back nuts. (i) 15mm

dia.d)Providing and fixing brass screw down stop tap.(A) 15mm

dia.e)Providing and fixing Rubber plug for sink or wash basin.

62 Providing and fixing rolling shutters of approved make made of 80mm 15.23 Sqm 4495.02

wide M.S.laths inter-locked together through their entire length and

jointed together at the ends by end locks mounted on specially

designed pipe shaft with bracket plates, guide channels and

arrangements for inside and outside locking with push-pull operation

complete but including the cost of hood cover and spring.(B) Shutters

having width 3.5 M. and above

63 Pointing on brickwork with cement mortar 1:3 (1-cement : 3- coarse 23.34 Sq.m. 99.11

sand) (B) Ruled pointing

64 Providing Hydraulic Excavator 1 cum bucket capacity @ 60 cum per 36.00 Hour 718.98

65 Structural steel work ( Confirming to IS 4923-1997) riveted, bolted or 62.10 Kg. 127.95

welded in builtup for all type sections, in framed work, including

cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer all complete as per the structural designs and

directions of Engineer in charge.Column ( 122 x 61 x 3.6mm )

66 Providing and fixing PVC Printed pain colour false ceiling with grid 66.76 Sq.m. 773.66

type with alluminium frame consisting of 600mm x 600mm 3mm

thick plain PVC sheet used as panel insert in a frame work made using

anodized alluminium T section of size 1 x 1 (235 x 25mm, 19 gauge

or 1 mm thick) in square pattern of grid sizes of 2 x 2 (600 x 600mm)

The alluminium frame work is supported from the cceiling with the

help of G.I. hook and G.I. wire/6mm M.S. rods of required sizes to

maintain proper level etc. The aluminium frame work is supported on

side wall with the use of alluminium L section of size 1 x 1 (25 x

25mm) angles etc. complete as per direction of Engineer in charge.

Manufactures specification and drawing.

67 Providing and fixing Jet spray heavy duty with S.S. Braided hose 60 1.00 Nos. 308.99

68 Providing and fixing Chromium platted bottle trap 3.00 Nos. 253.40

69 SITC 6 KG ABC TYPE FIRE EXTINGUISHER 3.00 Nos. 3282.50

70 SITC 4.5 KG CO2 TYPE FIRE EXTINGUISHER 3.00 Nos. 5908.50

71 Providing & Installation of Kitchen furniture size made of 19mm ply 2.84 Sq.m. 19813.62

,(BWP Playwood -IS ;710USED) with outer most Ply having 0.9 mm

Acrylic laminate confirming IS 2046:1995 and inner Ply having

regular 1.0 mm thick laminate confirming IS 2046:1995 having

required numbers of sets of SS Trollies and 550 mm depth with

required numbers & size of Handles made etc. at any position in

furniture made up on site as per architects drawing finished without

laminets/veneer ,as per architect's instruction .Rate includes all joints

of ply have to be fixed with S.S screws ,S.S nails , anti termite

treatment ,synthetic resin Adesives ,sticking tapes etc.complete. Items

to be approved by engineer incharge

72 Anti-Termite System:Providing and laying of permanent piping 191.88 Sq.m. 134.33

technology anti-termite treatment before flooring work by installing

LLDP (Low linear density polyethylene) tube of 8 mm O.D. &

mm 1.D. with inbuilt pressure compensation chip every 30 cm interval

in the tube, having working pressure of 2 Kg/cm2 and release rate of

1.9 Itr/hour fixed by P-clips and nails. The LLDP pipe shall be

installed at the entire periphery of the building and at internal network

of building at a depth of 20 to 200 mm under floor at every 2 to 3 mtr.

c/c distance (adjusted as per building layout ) & Ends of loop pass

through a PVC elbow of minimum 32 mm ID at junction box of wall

and floor level, entering into a steel reinforced grooved flexible pipe

of minimum 22 mm ID leading into junction box and the loops shall

terminate in junction boxes & test every junction during injecting

chemicals for termite control treatment. The anti termite chemical

Imidacloprid 30.5% SC mix as per IS-6313 (part III) shall be injected

by the pressure pump diluted with water @ 10.5 ml/5 ltr of water at

the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit

approved line plan for piping system and junction boxes dully

approved by Engineer-in-Charge with bond of 5 year warranty.(i)Anti

Termite chemical injected area (Chemical injecting incl. labour cost)

73 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 20.00 Pt. 449.45

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below type

of pipe erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed. (a) with medium class Rigid PVC pipe

and accessories erected flushed on wall/ceiling complete Cat. III

74 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 5.00 Pt. 638.32

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with earth

continuity of following type erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed.(a) with

medium class Rigid PVC pipe and accessories erected flushed on

wall/ceiling complete Cat. III

75 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm 5.00 Pt. 711.04

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected with

following type of accessories. [II] For 16A Plug and 16 amp switch

with 2-2.5 sq.mm Cu. Wire from mcb db board. (a) with medium class

Rigid PVC pipe and accessories erected flushed on wall/ceiling

complete Cat.III

76 Point wiring for on board Looped Plug with 6A Modular type switch 10.00 Pt. 257.55

& 5 pin socket erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front

plate modules erected on / in wall / ceiling with following type

accessories Cat III

77 Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm 5.00 Pt. 567.62

& earth wire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires erected in below

type of pipe with 6A Modular type switches and following type of

accessories erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected. with necessary

batten/angle holder or ceiling rose or H.D.Connector as directed. (a)

with medium class Rigid PVC pipe and accessories erected flushed on

wall/ceiling complete Cat III

78 Providing following type of Modular Type Accessories mounted with 5.00 Each 398.95

PVC / metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In

charge. (5) Electronic hum Free steps EME Fan regulator Cat.III

79 (7) Blank Plate Single Cat III 8.00 Each 25.25

80 (22) 16/20/25 Amp. Modular Starter for Motor / A.C. Unit Complete 2.00 Each 497.93

81 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated 185.00 Mtr. 82.82

ISI marked stranded Copper conductor wire in following type of pipe

to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour

for earth continuity of following size (A) With medium class Rigid

PVC pipe and accessories (b) 2 wire 2.5 sq. mm

82 Supplying and erecting led lamps with following wattage capacity of 18.00 Each 188.87

220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-

surge protection,Polycarbonate diffuser, mounting suitable for E14 /

E27 / B22 lamp holders, pf >= 0.5 (iii) 10 to 15 watts Cat-III

83 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 19.00 Each 589.84

Watt to 0.5 Watt assembled on single MCPCB, with housing used as

a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V.

& corrosion resistance with diffuser housed in aluminium casted

body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Square/ Circular shaped

Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20 (iii) 16-20 watts, Surge-2 KV Cat-III

84 Supply, Installation, Testing and Commissioning of suitable sweep, 5.00 Each 2885.57

BEE 5 Star rated, Ceiling fan with Brush Less Direct Current (BLDC)

permanent ferrite magnet Motor, class of insulation: B, Rust free

nos.Aluminium blades, 2 nos. canopies, shackle kit with earthing

provision, copper winding, Power factor not < 0.9, Service Value

(CMM/W) minimum 6.85, Air delivery minimum 215 CMM,

RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with remote

unit for Speed Control and all remaining accessories including safety

pin, nut bolts, washers, temperature rise = 75 degree C (Max.),

suitable for 140 to 285 Voltage and rectifier circuit with surge, over

current and overload protection , 50 Hz, Single phase AC Supply,

earthing etc. Complete as required.[ Make shall be approved by

Engineer in Charge] (B) 1200 mm Sweep (48")

85 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. 2.50 Mtr. 108.07

Pipe down rod erected duly painted for fan complete with proper

insulation without leakage and earthing.

86 Supplying & erecting fan hook box of 10 mm M.S. round bar 5.00 Each 108.07

bounded to the RCC bars up to 50mm length each side and pierced

through a 16 Gauge M.S. box / Heavy Duty PVC box complete

erected concealed in Ceiling with necessary finishing.

87 Supplying & erecting approved make low noise decorative exhaust fan 2.00 Each 1703.87

having square frame ABS body with inbuilt lowers & square frame.

200mm with 1350RPM Cat.II

88 Supplying & erecting earth pit of minimum bore dia.150mm size 1.00 Each 4591.46

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the

value of earthing resistane mentioned in test Certificate) & having

back filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back

fill Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted by

Agency. (a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

89 Providing and erecting Sheet Steel powder coated MCB distribution 1.00 Each 1492.78

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be

used of same company of MCB to be used) suitable for (A) single

phase incoming and horizontal single phase outgoing (b) sheet steel

double door (IP-43) (iv)12 way

90 providing and erecting Miniature circuit breaker single pole 6A to 8.00 Each 112.11

25A suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat III

91 providing and erecting Approved make RCCBs conforming to IS: 1.00 Each 2235.13

12640 and having sensitivity of 30 mA and Short Circuit withstand

capacity of 10 KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic component. for

following Max. rating erected as directed (ii) 40Amps. DP Cat.III

92 Providing and erecting Inverter based approved make split air- 2.00 Each 48257.80

conditioning unit consisting of condensing unit with variable speed

fan motor, inverter type hermetically sealed rotary compressor with

accessories etc. duly connected separately erected evaporating unit

and blower motor with its accessories by means of extra supplied

proper insulated copper tubing,drain PVC pipes suitable for ( cost

includes Eco Friendly green gas charging and 15A plug top & Remote

Control & MS Stand) with necessary core cutting. (1)For ISEER

Range (KWH/KWH)(3.1 to 3.99) (B) for 1.5 ton capacity - Premium

(GST Will be paid Separately)

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and words)

of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

Dy Accountant Executive Engineer

Vadodara Irr. Div. Vadodara Irr. Div.

Vadodara Vadodara