Special repairs to bldg. No II/16AF at 122 Inf Bn (TA), west hill, Calicut under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

M&L for structural steel work in tubular trusses including special shaped washer, two coats of synthetic enamel paint over a coat of primer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 all as specified and directed.

S&F for structural steel work with rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conform to Fe 410-W (Gde-E- 250 quality-A ) all as specified and directed

M&L for plates (plain or chequered) channels, square cut or notched (ordinary or counter sunk) forming holes, without any attachment complete all as specified.

Providing, cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

M&L for preparation of new steel surfaces of any description, not otherwise described exc 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

Dismantling ceiling boarding of any description fixed in any position with screws including covering fillets complete all as specified and directed.

S & F for anodized aluminium snap grid frame work as in clause No. 10.38 of MES Schedule Part I for false ceiling of size 605 mm x 605mm with supporting hanger comprising of 6 mm MS rod / GI flat 40x3mm, ‘J’ bolt with necessary washers, bolts and nuts for securing frame work to ceiling and to the snap grid complete all as specified and directed

M & L for 4mm thick High Pressure Steam Cured ( HPSC ) non asbestos fibre cement building boards fixed or laid/inserted to aluminium snap grid frame work with screws all as specified and directed.

M&L for preparation of new non AC ceiling board surfaces with two coats of Birla white putty finished the surface even and smooth and applying two coats of oil bound distemper over a coat of primer all as specified and directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles, 10mm to 12mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed ceramic tiles 350x250x7mm or 450x350x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Taking down chowkats with shutters exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

Taking down wooden door shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and refixing in same opening complete all as directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L Preparing and treating surfaces of steel and iron work, small articles such as stop, covers, gully gratings, holdfasts, etc., area n exc 0.1 sq. m each each treated with tar or coal tar black paint all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast, coping, bed block etc including necessary form works all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

M&L for second class hardwood, panelled shutter 30mm thick (two panel) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F second class hard wood glazed and skeleton shutters, 30mm thick open rebated, etc; with sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, divided into squares all as specified in clause No. 8.24 (a), section 8 of MES Schedule Part I, and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with first class hard wood beading in squares not exc 0.50 Sqm in each pane all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F for second class hard wood, plain fillets, square, rectangular or triangular in section, clean sawn, sectional area exc.6 & n. exc. 13 sqcm secured with nails or brads all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L for preparation of new surfaces of walls by applying a coat of Birla white putty and sanding the surfaces even and smooth. Applying one coat of wall primer (water thinable / solvent thinable) and applying two coats of tractor emulsion oil emulsion distemper all as specified and as approved all as specified and as directed.

M&L for Preparing newly plastered surfaces on external walls and applying one coat of exterior wall putty for smoothness, one coat of exterior wall primer and two coats of exterior emulsion anti-algal weather proof paint of Make : Asian Paints Apex Ultima or equivalent of Berger or Dulux all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treating back of chowkats,area tarred exc. 0.1 sqm but n.exc 0.5 sqm with tar or coal tar black paint each all as specified and directed.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F stainless steel butt hinges medium weight; 75mm size all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

S&F 150mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F harrison rails 25mm dia, mild steel chromium plated with fixing brackets etc complete all as directed.

S&F Floor door stopper Overall length of cover plate 140mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor etc complete all as directed.

NARAYANA CONSTRUCTIONS