Special Repair for upgradation of Sub Health Centre (SHC) into HWC at Village Tharwa (Under Majri P.H.C.) in Ambala District

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (HSR 8.5) (b) In cement (HSR 8.5) (b))

Dismantling Concrete (HSR 8.6) reinforced cement concrete with cleaning and straightening and cutting of bars if required. (HSR 8.6) (e))

Removing door and windows (wood and steel) with chowkats by making Recesses in walls when the wall is not to be dismantled:- (HSR 8.18) (a) Doors (HSR 8.18) (a)

(b) Windows (HSR 8.18) (b)

Scraping White wash and colour wash (HSR 8.32 (a))

Scraping Cement plaster. (HSR 8.32 (c))

Cement Concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth. (HSR 10.41).

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. (HSR 11.7)

Terracing consisting of tiles 22.86 cm x 11.43 Cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13) a) Using Old Tiles

a) Using New Tiles

Precast chequered tiles of 20 mm thickness In ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings. (Note:- Reputed make Tile Only ISI marked will be used as approved by Engineer-in-charge). (HSR 14.45+Note). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like:RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL (Double charged tiles shall be used as approved by Engineer in charge. (NS). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & fixing vitrified tiles of size 600mm x 600mm of approved make in skirting/dados laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL (Double charged tiles shall be used as approved by Engineer in charge. (NS). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.92(b)). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

12 mm thick cement plaster 1:4 (HSR 15.5)

Painting two coats with synthetic enamel Paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.5)

Preparation of plastered surfaces for Distempering including sand papering the surface, applying filling with approved quality filler, consisting of plaster of paris and chalk mitti including finishing the surface to the required finish complete. (HSR 16.51).

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work.(Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.60).

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on new work, two coats to give an even shade. (HSR 16.61)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.79 (a)). 2nd Quality

Steel work in hip and jack rafters, common rafters, purlins, etc., with angle iron cleats and other connecting plates welded including cost of cutting & welding rods. (HSR 18.6)

Wire gauze of 140 G or 120 G designation fixed on steel windows of standard rolled steel section, with 3 mm thick flat iron cover moulding of 12/5 mm width, fixed with machine, screws welded complete in all respects. (HSR 18.32)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, or approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- (HSR 18.34) (c) door and window frame size 127 mm X 50 mm with 40 mm wide double rebate (HSR 18.34) (c)

Providing and fixing M S angle and T-iron Frames for door, window and ventilator including iron hold fast, butt hinges of I.S.I mark fixed in positon with machine screws and duly welded including all other suitable locking arrangements provided and welded with the frame and making holes and fixing glazing clips in the frame filing the welds and finished with a coat of red lead non sotting primer complete in all respects. (HSR 18.35)

PROVIDING AND FIXING IN POSITOIN BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for Sinking into floor, with raised foot treads COMPLETE WITH 100 MM H.C.I, ‘P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above (HSR 30.2) (b) Size 630 mm (i) White

Providing & Fixing in position best Indian make (ordinary) lavatory suites consisting of:- (v) Size 560 mm x 450 mm with one no. tap. (HSR 30.41(v)).

Providing and fixing in position best quality Stainless Steel Sinks with Complete fittings as fully described in item No. 30.51. (a) 600 mm x 450 mm x 200 mm. (HSR 30.53 (a)).

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge) (HSR 30.75). (a) Bib cock long body (HSR 30.75) (a))

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. (HSR 30.76 (a) (ii)).

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. (HSR 30.119). 1000 Ltrs. Capacity Water Tank

Providing & fixing Acrylic Fibre Sheet shed with 2mm thick sheet with iron frame complete in all respects to the satisfaction to the Engineer-in-Charge. . (NS)

Supply and Fixing of G.I. Pipe complete in all respects to the satisfaction to the Engineer-in-Charge. . (NS) ½” Pipe

NOTE:- 1. IN CASE OF ANY DIFFERENCE IN THE UNIT & NOMENCLATURE OF ANY OF THE HSR ITEMS OF CIVIL, P.H. WORK DEPICTED IN THIS DNIT AND THAT GIVEN IN HSR, THE UNIT AND NOMENCLATURE GIVEN IN HSR SHALL BE APPLICABLE. 2. ONLY REPUTED MAKE MATERIAL WILL BE USED (MAKE/BRAND EXHIBITED IN HSR AND EXHIBITED IN APPROVED STANDARD DOCUMENT) AS APPROVED BY ENGINEER-IN-CHARGE, WHILE EXECUTING VARIOUS ITEMS/WORKS AT SITE.

HARISH CHANDER