Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1st₹3.7 LAccepted-AOC | 1st | Accepted-AOC 1st | |
| 2 | 2nd₹3.8 L+₹3,954.14 (1.06%)Rejected-AOC | 2nd | Rejected-AOC 2nd | |
| 3 | 3rd₹4.4 L+₹69,910.10 (18.7%)Rejected-AOC | 3rd | Rejected-AOC 3rd |
| Sl No | Description | Qty | Unit | SIJON NELLIPPILLY L2 | JIJUVP L3 | JOHN BOSCO S L1 |
|---|---|---|---|---|---|---|
| 1.00Roofing sheet laying | ||||||
| 1.00 | 50.6.1.5:Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete | 6.33 | cum | 7,279.04 ₹46,076.32 | 9,279.04 ₹58,736.32 | 7,133.46 ₹45,154.8 Lowest |
| 1.00 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | 31.65 | sqm | 369.77 ₹11,703.22 Lowest | 369.77 ₹11,703.22 Lowest | 369.77 ₹11,703.22 Lowest |
| 1.00 | 10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes | 624.96 | kg | 194.27 ₹1,21,410.98 | 194.27 ₹1,21,410.98 | 189.41 ₹1,18,373.67 Lowest |
| 1.00 | OD504909/2025-2026:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch
ofcorrugation as approved by Engineer-in-charge) 0.35 mm (+0.05%), total
coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel
grade, 5-7 microns epoxy primer on both side. of the sheet and polyester top coat 15-
18 microns.Sheet should have protective guard film of 25 microns minimum to avoid
scratchesduring transportation and should be supplied in single length upto 12 metre or
as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self
tapping screws ofsize (5.5x55mm) with EPDM seal, complete upto any pitch in
horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trusses
and including cutting tosize and shape wherever required
EST No. :LSGD/CELSGD/EST/16327/2022_5_1_1/RE 1 (Edit Id : 1)
(Dsor year : 2018,Cost Index (Place : Trichur,Value : 135.59),GST : 18%
Printed On | 44.64 | sqm | 619 ₹27,632.16 | 619 ₹27,632.16 | 520 ₹23,212.8 Lowest |
| 1.00 | OD504910/2025-2026:Supplying and fixing Pressed Steel Door of standard pattern with frames as per profile of IS:4351 of section 105*60mm using 18G (1.2mm thick CRCA) sheet and shutters made of section 75*30mm of outer styles and horizontal members and then inserted with enclosed and stiffened sheet 26CR as per the specification with zinc chromate primer including all charges of fittings, conveyance etc, complete. | 1.89 | 1 sqm | 5,500 ₹10,395 Lowest | 5,500 ₹10,395 Lowest | 7,899.4 ₹14,929.87 |
| 1.01 | 10.25.2:Item Shifted to Sub head 14 as item 14.73
Item Shifted to head 14 as item 14.74
Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | 300 | kg | 175 ₹52,500 Lowest | 175 ₹52,500 Lowest | 178.43 ₹53,529 |
| 1.01 | 21.1.1.1:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):
For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) | 4.4 | kg | 544.21 ₹2,394.52 Lowest | 544.21 ₹2,394.52 Lowest | 544.21 ₹2,394.52 Lowest |
| 1.01 | 21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):
For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) | 13.2 | kg | 584.71 ₹7,718.17 Lowest | 584.71 ₹7,718.17 Lowest | 584.71 ₹7,718.17 Lowest |
| 1.01 | 21.3.3:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) | 12 | sqm | 1,876.17 ₹22,514.04 | 3,500 ₹42,000 | 1,829.27 ₹21,951.24 Lowest |
Tender Value
₹3.8 L
EMD Value
₹9,511
Closing Date
18 Mar 2026, 6:00 pmClosed
Assistant Engineer
Assistant Engineer Lsgd Section Irinjalakuda Sub Division
Irinjalakuda BP 2025-26 Pro no.137/26 Extension of Parekkattukara women fitness centre ward 4 Muriyad Grama Panchayath-Sheet roofing-General Civil Work-Extension works.-General Civil Work
2026_LSGD_846098_1
ET6/AE/LSGD/ILK/2025-26 fitness
Open Tender
Civil Works - Others
Item Rate
180 days
Irinjalakkuda BP
Please refer Tender documents.
8 documents required · 8 mandatory
₹840
₹9,511
16 Jul 2026
11 Mar 2026
21 Mar 2026
11 Mar 2026
18 Mar 2026
11 Mar 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1Roofing sheet laying | |||||
| 1.001 | 50.6.1.5:Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete | - | cum | - | - |
| 1.002 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | 1 | sqm | - | - |
| 1.003 | 10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes | - | kg | - | - |
| 1.004 | OD504909/2025-2026:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch
ofcorrugation as approved by Engineer-in-charge) 0.35 mm (+0.05%), total
coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel
grade, 5-7 microns epoxy primer on both side. of the sheet and polyester top coat 15-
18 microns.Sheet should have protective guard film of 25 microns minimum to avoid
scratchesduring transportation and should be supplied in single length upto 12 metre or
as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self
tapping screws ofsize (5.5x55mm) with EPDM seal, complete upto any pitch in
horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trusses
and including cutting tosize and shape wherever required
EST No. :LSGD/CELSGD/EST/16327/2022_5_1_1/RE 1 (Edit Id : 1)
(Dsor year : 2018,Cost Index (Place : Trichur,Value : 135.59),GST : 18%
Printed On | - | sqm | - | - |
| 1.005 | OD504910/2025-2026:Supplying and fixing Pressed Steel Door of standard pattern with frames as per profile of IS:4351 of section 105*60mm using 18G (1.2mm thick CRCA) sheet and shutters made of section 75*30mm of outer styles and horizontal members and then inserted with enclosed and stiffened sheet 26CR as per the specification with zinc chromate primer including all charges of fittings, conveyance etc, complete. | 1 | 1 sqm | - | - |
| 1.006 | 10.25.2:Item Shifted to Sub head 14 as item 14.73
Item Shifted to head 14 as item 14.74
Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | - | kg | - | - |
| 1.007 | 21.1.1.1:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):
For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) | - | kg | - | - |
| 1.008 | 21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):
For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) | 1 | kg | - | - |
| 1.009 | 21.3.3:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) | - | sqm | - | - |
stage.html
html • 0.04 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_1429226.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Tendernotice_1.pdf
PDF • 0.28 MB
pa.pdf
Tender Documents • 0.26 MB
form.pdf
Tender Documents • 0.26 MB
in.pdf
Tender Documents • 0.23 MB
affa.pdf
Tender Documents • 0.24 MB
ep.pdf
Tender Documents • 0.23 MB
BOQ_1429226.xls
BOQ • 0.31 MB
viewnit.pdf
Tender Documents • 0.03 MB
viewsbd.pdf
Tender Documents • 1.72 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .