Construction of Combined office Building at Balichowki in Distt. Mandi SH C/o Building portion WS and SI Rain water harvesting system and Septic tank

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to all floor level and removal of same for insitu reinforced concrete and plain concrete work as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . Foundation footings and bases of columns etc. and mass concrete .

Flat surface such as soffits of suspends floors, roofs, landing and the like floor etc. upto any thickness.

Columns, pillar, post and struts. Square, rectangular or polygonal in plan.

Beams, cantilevers, girder and lintel, sides and soffits of beams, beam haunching, cantilever, brsssumers and lintels not exceeding one metre in depth in all heights from floor.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Edges of slab and breaks in floor and walls any width

Stair case with slopping or steped soffits excluding landing.

Providing and laying cement concrete 1:6:12 (one cement: six sand: twelve graded stone aggregate 40mm nominal size) mechanically mixed and curing complete excluding cost of centering , shuttering in foundation and plinth.including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 25mm (Twenty five millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (fourty millimetre) nominal size) excluding cost of centring and shuttering in foundations and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying Reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforsed cement concrete work. The mix shall be designed as per requirement of I.S. code and PWD specification. The design mix will be got approved from the Engineer-in-Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix asper IS code upto floor all floor level including carriage of materials with in all leads, lifts and other incidentals. Foundation footings bases of columns and the like and mass concrete.

Suspended floors, roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever .

Columns, pillar, post and struts :

Wall (any thickness but not less than 0.10 m thickness) attached pilasters, buttresses, plinth and string courses etc.

Stair case with slopping or steped excluding landing but includind preparing of the surface and finishing of nosing .

Providing and laying Reinforced cement concrete design mix M-20 (twenty ) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforsed cement concrete work. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer-in-Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix asper IS code in moulding as in cornices windows sills etc. upto any girth upto floor all floor level including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying reinforced cement concrete design mix M-20 (twenty ) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reincofcement for reinforced cement concrete work. The mix shall be designedas per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer-in-Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per IS code upto floor all floor level including carriage of materials with in all leads, lifts and other incidentals. Suspended floors, roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever .

Wall (any thickness but not less than 0.10 m thickness) attached pilasters, buttresses, plinth and string courses etc.

Providing and laying cement concrete 1:2:4 (one cement: two Sand: four graded stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work in Foundation and plinth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing tor/mild steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete up to floor any level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Brick work using common burnt clay building brick in super structure in cement mortar 1:6 (One cement : Six sand ) with 2nd class bricks up to floor all level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Half brick masonry in common burnt clay building bricks in super structure in cement mortar 1:3 (One cement : three sand ) 2nd class bricks up to floor any level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Extra Brick masonary for forming cavity 5cm. to 7.5cm. (five centimetre to 7 point five centimetre) wide in cavity walls with necessary weep and vant holes including use of cores and cost of providing and fixing bitumastic coated M.S. Ties of 25mm x 3mm ( twenty five millimeter into three millimetre) section at not less then 3 (three) ties per square metre as per approved design including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge ..

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in Cement Mortar 1:6 (one cement : six sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in Cement Mortar 1:3 (one cement : three sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement : six sand : twelve graded stone aggregate 20mm (twenty millinetre) nominal size) at plinth level in Cement mortar 1:6 (one cement : six sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Backfilling behind abutment, wing wall, R/walls and B/walls complete as per drawings and technical specifications clause 1204.3.8 including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing & fixing factory made uPVC of approved color casement/casement cum fixed glazed windows comprising of uPVC multi chambered frame, sash & mullion(where ever required) extruded profile.Including tower bolts, handle, hooks & eyes etc, in ncessary panels. Frame should be duly reinforced with 1mm G.I. section and Sash/Mullion with 1.5 to 2mm thick G.I. section based on wind load calculation, (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, Co-extruded TPV Gasket having separate dranage system, stainless steel (SS 304 grade) friction hinges, zinc alloy(white powder coated) casement handles, whereever necessay fly wire mesh should be included in frame, G.I. Fasteners 100x8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of Frame & Sash shall be metered cut and fusion welded at all corner, Mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware & drainage of water etc. After fixing frame, the gap between frame and adjacent wall shall be filled with PU Foam / backer rod of required size & approved quality. After that sealed with weather proof silicon sealant at both the side(inside & outside), all complete as per approved drawing specification & direction of Engineer-in- Charge Casement window single panel with friction hinges 300x19x1.9 mm (three hundred into nineteen into one point nine millimetre) made of frame 60x55 mm (sixty into fifty five millimetre) & sash 60x75 mm (sixty into seventy five millimetre) both having wall thickness of 2.2+-0.2 mm and double glass pane glazing bead 34x20 mm ( thirty four into twenty millimetre) or appropriate dimension. Windows shall be provided with 6mm (six millimetre) thoughned glass (outside + 12 mm air gap + 5mm (inide clear toughned glass. (Area up to 0.75 sqm) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Casement window double panel with top fixed with SS friction hinges 350x19x1.9 mm (three hundred fifty into nineteen into one point nine millimetre) made of frame 60x55 mm (sixty into fifty five millimetre) , sash 60x75 mm (sixty into seventy five millimetre) & mullion 60x74 mm (sixty into seventy four millimetre), all having wall thickness of 2.2+-0.2 mm and single glazing bead 34x20 mm (thirty four into twenty millimetre) or appropriate dimensiom. ) Windows shall be provided with 6mm (six millimetre) thoughned glass (outside + 12 mm air gap + 5mm (inide clear toughned glass. (Area above 0.75 sqm & up to 2.50 sqm) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Casement window double panel with top fixed with SS friction hinges (350x19x1.9 mm) (three hundred fifty into nineteen into one point nine millimetre) made of frame 60x55 mm (sixty into fifty five millimetre), sash 60x75 mm(sixty into seventy five millimetre) & mullion 60x74 mm (sixty into seventy four millimetre) , all having wall thickness of 2.2+-0.2 mm and single glazing bead 34x20 mm (thirty four into twenty millimetre) or appropriate dimensiom. ) Windows shall be provided with 6mm thoughned glass (outside + 12 mm air gap + 5mm (inide clear toughned glass. (Area above 2.50 sqm & up to 5.00 sqm) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing & fixing factory made uPVC approved color casement/ casement cum fixed glazed door comprising of uPVC multi chambered extruded frame, sash & mullion(where ever required), profile. Including sliding door, door stoper, tower bolts, handle tc. complete in ncessary panels Frame should be duly reinforced with 1mm G.I. section and Sash/Mullion with 1.5 to 2mm (one point two into two) thick G.I. section based on wind load calculation, (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, TPV Gasket having separate dranage system zinc alloy (white powder coated) 3D hinges and one handle on each side of the panel along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. Fasteners 100x8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of Frame & Sash shall be metered cut and fusion welded at all corner, Mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware & drainage of water etc. After fixing frame, the gap between frame and adjacent wall shall be filled with PU Foam / backer rod of required size and the approved quality. After that sealed with weather proof silicon sealant at both the side(inside & outside), all complete as per approved drawing specification & direction of Engineer-in- Charge. Providing & fixing Casement door with 3D hinges made of frame 60x55 mm (sixty into fifty five millimetre) & sash 60 x 102mm (sixty into one hundred two millimetre) both having wall thickness 2.2+- 0.2 mm and single/double glazing bead 34x20 mm (thirty four into twenty millimetre) /20x21 mm (twenty into twenty two millimetre) or appropriate dimension. Doors shall be provided with 6mm plain float glass. (Area up to 3.00 sqm) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing & fixing Casement door with top hung ventilator at the top, with 3D and SS Friction hinges 400x19.1.9 mm (four hundred into nineteen into one point nine millimetre) made of 60x55 mm (sixty into fifty five) , sash 60x102 mm (sixty into one hundred two millimetre) and mullion 60x74 mm (sixty into seventy four millimetre) all having wall thickness of 2.2+-0.2 mm and single/double glazing bead 34x20 mm (thirty four into twenty millimetre) /20x21 mm (twenty into twenty two millimetre) size or appropriate dimension. Doors shall be provided with 5mm plain float glass (Area above to 2.5 sqm and upto 5.00sqm) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing & fixing Casement door with top hung ventilator at the top and fixed glazing at both side of door with 3D and SS Friction hinges 400x19.1.9 mm (four hundred into nineteen into one point nine millimetre) made of 60x55 mm (sixty into fifty five millimetre), sash 60x102 mm (sixty into one hundred two millimetre) and mullion 60x74 mm (sixty into seventy four millimetre) all having wall thickness of 2.2+-0.2 mm and single/double glazing bead 34x20 mm/20x21 mm size or appropriate dimension. Doors shall be provided with 5mm plain float glass (Area above 5.00 sqm upto 8.00 sqm.)

Providing & fixing Casement door with top hung ventilator at the top and fixed glazing at both side, two openable door in frame with 3D and SS Friction hinges (400x19.1.9 mm) made of 60x55 mm, sash 60x102 mm and mullion 60x74 mm all having wall thickness of 2.2+-0.2 mm and single/double glazing bead 34x20 mm/20x21 mm size or appropriate dimension. Doors shall be provided with 5mm plain float glass (Area above 8.00 sqm.) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 1st class indian teak wood 75mm x 62.50mm (seventy five into sixty two point five millimetre) moulded hand rails in straight length complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge..

Providing and fixing 1st class indian teak wood machine curved baluster of 50 mm (fifty millimetre) dia. out of 60mm (sixty millimetre) dia. with ends housed (square or splay) to hand rails and treads or strings complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 19mm (nineteen millimetre) thick MDF for cup boards i/c fixing (with nickel plated piano hinges with screws etc. complete) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing wood work in first class kail wood frames work in panelling partitions etc. sawn and put-up in position including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 12 mm (twelve millimetre) thick marine ply I.S.I. marked for panelling of approve quality with jointing and nails (Frame work and cover fillets to be measured for separately) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge..

Providing and fixing 4 mm (four millimetre) thick veneered decorative plywood lining with decorative surface on one face with butt jointing and nails (frame work and cover fillets to be measured and paid forseparately) veneers laminate (teak ply) including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 1.00 mm (one millimetre) thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 1st class indian teak wood 75 mm x 60mm (seventy five into sixty millimetre) decorative cornice in straight length complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 1st class indian teak wood square edges cover fillets (beading) 19mmx6mm (nineteen into six millimetre) section i/c mitring at junctions with wood screws and nails complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 8mm (eight millimetre) thick MDF board shutterfor cupboad etc. with necessary screw, hinges etc. complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing magnetic catcher with screws etc. complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing 125 mm (one hundred twenty five millimetre) stainless steel decorative handles in cupboard with necessary screws etc. complete. including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge.

Providing and fixing G.R.C. (Unistone) 12mm.(twelve millimetre) cladding on R.C.C.surface side as on faces of Arch masonry walls etc.on 12mm. thick cement plaster 1:3(one cement: three sand) jointed with the range of chemical adhesive plaster and i/c scaffolding etc. complete including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and laying Cobble stone 10cm (ten centimetre) thick in flooring 10cmx 10cm (ten into ten centimetre) in flooring on a bed of 20mm. (twenty millimetre) thick cement mortar 1:3 (one cement: three sand) finished with flush pointing in white cement up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and laying spartic ceremic tiles 5.5mm.thick (five point five millimetre) in flooring 300 x300mm. (three hundred into three hundred millimetre) size treads of steps laid on a bed of 12mm. (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) finished with flush pointing in white cement up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty exterior grade vetrified tiles Nitco or equivalant 450 mm x 450 mm x 10 mm ( four hundred fifty into four hundred fifty into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600 mm x 600 mm x 10 mm (six hundred into six hundred into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

25 mm cement concrete flooring 1:2.5:3.5 (one cement : two point five sand : three point five graded stone aggregate of size 12.5 mm (twelve point five millimetre) and below by volume) laid over set and hardened face of structural slab or base concrete and finished with a floating coat of neat cement (using cement slurry for bond at the rate of 2.75 kg (two point seventy five kilograme) of cement per square metre of floor) up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and fixing WI-parquet/ Action TESA or equivalent (Clip -in-prelaminated ) wooden flooring (HDF) over CC base with polythene sheet and theromo sheet cushion below etc. complete up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco/AGL oe eqyivalent in matt finish in 600mm x 600 mm x 10 mm (six hundred into six hundred into ten millimetre) or 300mm x 300 mm x 10 mm (three hundred three into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty full body vetrified tiles Nitco or equivalant 3000 mm x 150 mm x 10 mm (three thousand into one hundred fifty into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and laying granite stone in flooring 20mm ( twenty millimetre) (average) thickness base of cement mortar 1:3 (one cement: three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm (twenty millimetre) thick up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and laying digital ceremic glazed tiles 8mm (eight millimetre) thick in flooring 300 x 600 mm (three hundred into six hundred millimetre) size treads of steps 1.50m (one point fifty metre). high tiles in dado. laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement: three sand) finished with flush pointing in white cement up to any floor two level including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty exterior grade vetrified tiles Nitco or equivalant 450 mm x 450 mm x 10 mm (four hundred fifty into four hundred fifty into ten millimetre) manufactured of approved shade and colourin skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete up to any floor two level including carriage of material within all leads and lifts and other incidentals.as per direction of Engineer-in-charge .

Providing and laying Duro stone vetrified tiles 300x300mmx8mm (three hundred into three hundred into eight millimetre) in grey/coloured of required shade in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete up to any floor two level including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 10mm (ten millimetre ) thick anti skid water proof stain and impect resistent heavy duty full body vetrified tiles Nitco or equivalant 3000 mm x 150 mm x 10 mm (three thousand into one hundred fifty into ten millimetre) manufactured of approved shade and colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete up to any floor two level including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and laying granite stone 20mm (twenty millimetre) (average) thicknessand colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete. 20 mm (twenty millimetre) thick up to any floor two level including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing sandwich puff roofing with top and bottom skin of 0.60mm (Zero point six zero milimetre) and overall thickness of pufft 40mm (forty milimetre) and weight of puff 35-37 cum thick prepainterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts other incidentals.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (ziro point sixty millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty ) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with screws prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.

Providing and fixing valley 90 cm (ninety centimetre) overall 0.60mm (ziro point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with screns prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 100 mm (hundred millimetre) dia pipe on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 15 cm. (fifteen centimetre) wide 45 cm. (fourty five centimetre) overall semicircular 0.60mm (ziro point sixty millimetre) thick Steel sheet pre painted sheetgutter with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of material within all leads and lifts and other incidentals

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge PVC Plain bend 100mm dia (hundred millimetre)

PVC corner type bend 100mm dia (hundred millimetre)

PVC shoe 100mm dia (hundred millimetre)

Providing and fixing Calcium silicate tile ceiling of size 600x600mm (six hundred into six hundred millimetre) of everest, dexune etc. over rady masde power costed metal heet section frame work complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Aluminuim metal ceiling of Monard of size 600x 600mm (six hundred into six hundred millimetre) and 0.70 mm (ziro point seventy millimetre) thickness profile of approved quality etc. complete up to any floor to level including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Chromiun plated Grab bar with necessary fittings etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing M.S. BP Sheet 1.66mm (one point sixty six milllimeter) to 2mm (two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separtely) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 8mm (eight millimetre) thick Fiber board sofitof roof portion complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing M.S. BP Sheet 1.66mm (one point sixty six milllimeter) to 2mm (two millimetre) thick in decorative facia fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separtely) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint including carriage of material within all leads and lifts and other incidentals In beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

In gratings framed guard bars,ladders, railling, brackets and similar works

Providing and fixing three layer polycarbonae tranparent sheet 1.20mm (one point twenty millimetre) thickness of each layer in roofing with galvanised J or L hooks bolts and nuts with G.I. Limpet and bitumen rubber washer complete with all accessories as required including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely.) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Chromium plated steel string for holding canopy & other things with necessary screws, holder etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Painting two costs (excluding priming coat) on new steel and other metal surfaces eith enamel paint brushin to give an even shadeincluding cleaning the surface of all dirt,dust and other foregin matters with Enamel paint other than white including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with Ready mixed paint brushing wood primer pink including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Painting two coats (excluding priming coat) on new wood and wood based surfaces,with readymixed paint, brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping With enamel paint other than white including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade in ceiling/roof surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer. for distempering with oil bound distemper on ceiling and/or sloping roofs including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and laying 6mm (six millimeter) Cement plaster to ceiling in Cement mortar 1:3 (one Cement: three Sand) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and laying 15mm (fifty millimetre) cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth.In Cement mortar 1:3 (one Cement: three Sand) Upto floor two level including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and laying 20mm (twenty millimetre) Cement plaster in two coats,backing coat 15mm and finishing coat 5mm (five millimetre) thick on rough side of brick/stone masonry walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing plinth protection 50mm (fifty millimetre) thick in cement concrete 1:3:6 (one Cement : three Sand :six Graded stone aggregated 20mm (twenty millimetre) nominal size) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (fourty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (one Cement : six Sand) and inside plastring with cement plaster 1:3 (one Cement: three Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (one Cement : five Sand : ten graded stone aggregate) of 40 mm (fourty millimetre) nominal size) and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and laying water proofing treatment , by applying cement slurry mixed with water proofing cement compound of Dr. Fixit Pidfin or equivalent consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 ( one cement : three sand) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Suppliying cast iron cover without frame for manholes For frame of internal dimension 455mmx610mm rectangular C.I. cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg. including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 110 mm (one hundred ten) dia. high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing PVC cowl IS marked including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 110 mm (one hundred ten) dia. PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Cascade NXT C0207 wall hung closet 540 x 365 x 395 (five hundred fourty into three hundred sixty five into three hundred ninty five) in white shade of Perryware/Jaquar/Hindware with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(one cement : one sand) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(one cement : one sand) (Seat and over to be measured and paid for separately) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . Angle Indian Universal closet

Providing and fixing G.I. Inlet connection for flush pipe with W.C.Pan including carriage of material within all leads and lifts and other incidentals

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Flat back type of size 430mm x 260mm x 350mm (four hundred thirty into two hundred sixty into three hundred fifty millimetre) vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (waste pipe to be measured and paid for separately) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) :- Vitreous China 5 litres capacity including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clanmps etc. (all in C.P. Brass) including cutting holes and makng good the same 15mm (fifteen millimetre) nominal bore including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Flat back 550mm x 400mm (five hundred fifty into four hundred millimetre) vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing rubber plug for sink / wash basin 32mm (thirty two millimetre) dia including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing C.P. Brass waste for wash basin or sink 32mm (thirty two millimetre) dia including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing M.I. Union for wash basin or sink 32mm (thirty two millimetre) dia including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 600mm x 450 mm (six hundred into four hundred fifty millimetre) bevelled edge miror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing C.P. Brass Towell ring coplete with C.P. Brass brackets fixed to wooden pluges with C.P. Brass screws including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing toilet paper holder No 1533 of Jaguar/ESS-Ess or its equivalent in C P Brass including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing charomium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Division Plate for Urinals 600mm x 300.mm (six hundred x three hundred millimetre) Vitreous China including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass bib tap with Capstan head of Jaguarincluding carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass pillar tap with Capstan head 15 mm dia of Jaguar including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing C.P. brass angle valve 15mm (fifteen millimetre) without nuts and pipe including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing C.P. stop cocks 15 mm (fifteen milliemetre) dia including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing P.V.C. connection pipe 300/450mm (three hundred/four hundred fifty millimetre) length 15 mm (fifteen millimetre) nominal bore with brass unions including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing brass full way valve with wheel 15mm (fifteen millimetre) nominal bore including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-AL-PE) composite pressure pipe U.V. stablized with carbon black confirming to IS-15450-2004 water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 1216 (16mm O.D. pipe (sixteen millimetre)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . Equal Tees. (i) 1216

Female branch TEE. (i) 1216 x 1216 x 15mm thread.

Female elbows:- 1216 x 15mm thread.

Male thread connector:-1216 x 15mm thread.

Female thread connector:- 1216 x 15mm thread.

Couplers:- (i) 1216

Providing and fixing PVC water storage tank 1000 litres (one thousand litres)net capacity of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing UPVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm X 90 mm. (one hundred ten into ninty millimetre)

110 mm X 75 mm (one hundred ten into seventy five millimetre)

Providing and fixing high pressure UPVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm dia. (one hundred ten millimetre)

75 mm dia. ( seventy five millimetre)

Providing and fixing UPVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm dia. (one hundred ten millimetre)

75 mm dia. ( seventy five millimetre)

Providing and fixing UPVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm dia. (one hundred ten millimetre)

75 mm dia. ( seventy five millimetre)

Providing and fixing UPVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm dia. (one hundred ten millimetre)

75 mm dia. ( seventy five millimetre)

Providing and fixing UPVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm dia. (one hundred ten millimetre)

75 mm dia. ( seventy five millimetre)

Providing and fixing UPVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm dia. (one hundred ten millimetre)

75 mm dia. ( seventy five millimetre)

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . 110 mm dia. (one hundred ten millimetre)

75 mm dia. ( seventy five millimetre)

Providing and fixing stainless steel kitchen sink 610 x460 mm (six hundred ten into four hundred sixty millimetre) with boul depth 200 mm. (two hundred millimetre) of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing PTMT Coloured / white high density polythelene / poly propylene 10 litres (ten litres) capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovr flow pipe, 40mm (fourty millimetre dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge .

Providing and fixing PTMT waste coupling of approved quality and colour 32 mm (thirty two millimetre) nominal bore including carriage of material within all leads and lifts and other incidentals

Providing and fixing PTMT urinal waste coupling of approved quality and colour including carriage of material within all leads and lifts and other incidentals

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube including carriage of material within all leads and lifts and other incidentals

Providing and fixing 100 mm (hundred millimetre) dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of material within all leads and lifts and other incidentals

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 ( one cement : five sand)and water tight C. I . cover with frame of 300mmx300mm (three hundred into three hundred millimetre) size (inside) the weight of cover to be not less than 4.53kg (four point fifty three kilograme) and frame to be not less than 2.72kg. (two point seventy two kilograme) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . Round Mouth Traps:100mm x 100mm (one hundred into one hundred millimetre) size P or S type

Constructing manhole with R.C.C top slab in 1:2:4 ( one cement : two sand : four graded stone aggregate twenty millimetre nominal size ) foundation concrete1:4:8 (one cement : four sand : eight graded stone aggregate 40mm (fourty millimetre) nominal size) inside plastering 15mm (fifty milllimetre) thick with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) finished smooth complete including curing and testing including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge . Inside size 800mm x 800mm (eight hundred into eight hundred millimetre) and 500mm (five hundred millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm (four hundred fifty five into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg (thirty eight kilograme) . (weight of cover 23 kg (twenty three kilograme) and weight of frane 15 kg.( fifteen kilograme) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge With 300mm ( three hundred millimetre) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand). With 300mm ( three hundred millimetre) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand).

Inside size 800 mm x 800 mm (eight hundred into eight hundred millimetre) and 1000 mm (one thousand millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455mmx610mm (four hundred fifty five into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg (thirty eight kilograme) (weight of cover 23 kg (twenty three kilograme) and weight of frane 15 kg.( fifteen kilograme) including carriage of material within all leads and lifts and other incidentals as per direction of Engineer-in-charge With 300mm ( three hundred millimetre) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand).

YOG RAJ SHARMA

Tenzin Construction Co. Pvt. Ltd.

JEET KUMAR GUPTA