CERTAIN REPAIRS TO PLUMBING, SANITARY FITTING AND MISC B/R WORK UNDER AGE B/R-II AT AF STN JODHPUR

Amount

S&F in repairs CP Bib taps fancy type 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back. Size 550 x 400 mm excluding taps, waste chain & plug & porcelain stopper but including brackets complete all as specified and as directed by Engr-in-Charge.

S&F in repair for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers & waste; including bedding in CM to dwarf wall or including fixing cantilever brackets & connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair for sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 litr capacity, low level, white, with intel, ball valve, float & handle including brackets complete all as specified and directed.

S&F in repair for mirror of 5 to 6 mm thick glass with double coat of protection and longevity grounded edges for safety and silver plating on the back for better reflection including with stainless steel decorative fastener/studs complete all as specified and directed.

S&F in repair Stop valves/angle valve 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) white including necessay fitting etc complete all as specified and as directed.

S&F in repairs Vitreous China squatting pan of orissa pattern size 580mm 440 mm white with `p' or `S' trap, front or back inlet & integrated foot rests, including provision of cement concrete bedding complete all as specified and as directed.

S&F in repair Vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement, with grating and union for discharge pipe and PVC waste pipe, including making all connections to existing connections, fixed complete all as specified and as directed.

S&F in repair for brass chromium plated urinal spreader fancy type of approved quality fixing with 15 mm dia pipe complete all as specified and directed.

S&F in repair for 15 mm bore Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight15mm-110gms) complete all as specified and directed.

S&F in repair for Angle valve /stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed.

S&F in repair for 15 mm bore Bib tap standard of PTMT any colour fancy typehigh pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm 125gm) complete all as specified and directed.

S&F 20 mm dia bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe including taking down old ball valve complete all as specified and as directed [Minimum weight for 20 mm – 210 gms].

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm, including taking down old PVC connection all as specified and as directed.

S&F in repair for health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 meter lomg flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified and directed by Engr-in-Charge.

S&F in repair CP grating of size 100 mm dia with/without waste hole complete all as specified.

Supplying and fixing of CPVC pipes 20 mm dia (outer dia) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down old u/s pipe complete all as specified and directed.

Supplying and fixing of CPVC pipes 25 mm dia (outer dia) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down old u/s pipe complete all as specified and directed.

S&F in repairs 32mm dia, 800mm long flexible PVC waste pipe complete all as specified and as directed.

S&F in repairs for 38/40 mm dia, low density polyethylene pipe up to 1.00 Metre long suitable for flushing cistern, etc with necessary fittings complete all as specified and as directed.

S&F 110 mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down old pipes all as specified and as directed.

S&F in repair for 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair for 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repairs PVC (SWR) bends any radius 75 mm dia all as specified and as directed.

S&F PVC (SWR) bends any radius 110 mm dia of bore, including taking down old bends all as specified and as directed.

S&F in repair for 15 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair for One piece EWC with seat cover and Twin flush fittings of size 640 mm x 350 mm x 725 mm of snow white colour incl 220 mm S trap complete all as specified and directed. Make - Cera Catpart No. S1013208VS(Cattler)/Jaquar Cat part No. FSS-WHT-29853S300UFSM(Fusion)/Johnson Cat part No. G3907P0103 (VIGO) as approved by GE.

S&F in repair for counter top wash hand basin of size 520 mm x 450 mm x 200 mm of snow white colour incl all necessay fittings etc complete all as specified and directed (Make Cera Cat part no. S2030101 (Clair) / Johnson Cat part No. P6212PW0401 (Grande) /Jaquar cat part No. ARS-WHT-39601(ARIA) as approved by GE.

S&F in repair for 15 mm bore CP wall mixer (3-in-1 ) for mixing hot and cold water with arrangement for both telephonic hand shower and overhead shower with long bend pipe complete all as specified and directed. Make - Cera cat part No. F1005413 (Ruby))/Johnson Cat part No. T3223C (Fusion)/Jaquar Cat part No. FUS-29281(Fusion) as approved by GE.

Demolition of cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) and disposing of debries outside MD land complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar complete all as specified and directed by Engr-in- Charge.

Dismantling of wall & ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including hangers etc complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework complete all as specified and directed.

Dismantling of old unserviceable, rusted, broken (corrugated/semi corrugated, etc.) asbestos cement/any type of sheets in ridge and roof coverings complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter (without taking off shutters from the frame) not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frame) exceeding 1.5 Sqm not exc.4 sqm each complete all as specified and as directed.

M&L for precast cement concrete 1:3:6 type C1 (Using 20 mm graded stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 including demolition of old u/s blocks complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate in cills, steps, bands, copings, bed plates, blocks for inserting hold fasts etc. and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by Engr-in-Charge.

M&L for squared rubble walling, Jodhpur type, brought up to courses, well bonded, bedded and solidly hearted, built in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L for 15 mm thick rendering in cement mortar 1:4 or fair faces of brick, stone or concrete surfaces finished even and smooth without using extra cement complete all as specifed and as directed.

M&L for 35 to 40 mm thick precast RCC Jallies of pattern as approved including frame, balusters, bressumers, kneelers, string courses fixing in any position with CM 1:4 including demolition of old jallies and thrown outside MD land complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coat of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of new surface and finishing walls with two coat of acrylic smooth exterior paint with required shade over a coat of primer complete all as specified and directed.

M&L for preparation of old surfaces of wall, by applying 2 to 3 mm thick white cement base putty in patches as required and applying two coat of oil bound distemper complete all as specified and directed.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 including dismanting of old u/s existing MS work complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise discribed, and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

Supply and fix in repairs 20 mm dia with 1 mm wall thickness curtain rod in any length, high strength stainless steel pipe including required bracket/finials complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors complete all as specified and as directed by the Engr-in - Charge.

M&L for vitrified light shade coloured tiles 9 to 10 mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in cement mortor 1:6 complete all as specifed and directed.

S&F coloured non skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for vitrified light shade coloured tiles 9 to 10 mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 1.00 sqm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plastering in CM 1:4 as in backing coat of tiles complete all as specifed and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/ 450 x 300 x 7mm/ 300x600x 7 mm thick over and including 10 mm thick rendering in cement mortar 1:4 as in backing coat for tiles on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specifed and directed.

M&L granite of 18 to 20mm thick, work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including screed layer of 15 mm thick in CM 1:4 all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregates as in sub base complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated trapezoidal shape steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F in repairs 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

S&F for 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule including taking down old one all as specified and as directed.complete all as specifed and directed.

S&F for rotational moulded polyethylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule including taking down old one all as specified and as directed.complete all as specifed and directed.

S&F for anodised aluminium frame/shutter section for doors, windows, ventilators,partition etc with one or more rebates including joining cleat for fixing complete all as specified and directed.

Add extra for powder coating on above item No 66 (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F for 4.8 mm thick sheet glass ordinary quality in square exc 0.50 Sqm each in each pane including necessary rubber beading etc complete all as specified and as directed by Engr-in-Charge.

S&F for 12 mm thick Prelaminated particle board, interior grade prelaminated both side of approved colour lamination, fixed with screws to any type of frame work complete all as specified and directed by Engr-in-Charge.

S&F for butt hinges medium weight cold rolled mild steel of size 100 mm complete all as specified and directed.

S&F for Aluminium anodised barrel tower bolt, of extuded section and fixed of 150 mm long complete all as specified and directed.

S&F for 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F extruded aluminium alloy handles fabricated type, anodised 150 mm long all as specified and directed.

S&F in repair for 12 mm thick WPC (wood polymer composite) board with CNC approved pattern/design cutting of approved colour with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position incl all necessary fittings, adhesive, sealent etc complete all as specified and directed.

S&F in repair for 3 to 4 mm thick coloured ACP sheet cladding over MS frame work or any other surfaces including making necessary arrangement for light, vertical, horizontal offset of any size/any pattern complete all as specified and directed.

S&F in repair for powder coated GI grid frame work of size 605 mm x 605 mm for false ceiling fixed with screw suspended with 6mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleates made out of GI flat 40 x 3 mm size 60mm long complete all as specified and as directed by Engr-in-Charge.

S&F for 5 to 6 mm thick PVC ceiling board fixed in flat surfaces on snap grid frame work including complete all as specified and directed.

S&F for solid PVC wall lining consisting of 5mm thick single side prelaminated PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

S&F in repair for Venetian blinds, vertical/horizontal type, 100 mm wide with polyester fabric of approved colour and pattern with aluminum fittings, and top rail and nylon buttons / loops etc., fixed cuttings and alteration if necessary wherever AC / coolers exists including dismantling of old unserviceable venetian blinds, complete all as specified and as directed.

M&L for factory made Vitrified heavy Duty parking tiles coloured, matt finish,unglazed and unpolished of size 300x300x10mm thick including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed by Engr-in-Charge.

S&F in repair for fancy type overhead shower of size 200 x 200 mm with necessary fittings complete all as specified and directed. Make- Cera Cat part No. F7010503AB/Jaquar cat part No. OHS-35497/Johnson cat part No. S0006C as approved by GE.

Om Trading Corporation (BID ID -3314063)

AAI NATH ENTERPRISES (BID ID -3313512)

VIKAS CONSTRUCTION CO. (BID ID -3313920)

Keystone Constructionare (BID ID -3321127)

Savitri Enterprises (BID ID -3321336)