REPAIR AND PAINTING INCLUDING MAINT OF STEEL FURNITURE AT OTM MD BUILDINGS UNDER GE ROORKEE

Amount

Almirah large steel FD-1031 and similar pattern: Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

Shelf

Cleat for shelf

Hinge

Shutter Left/right sheet of MS sheet to match the existing Almirah

Handle

Lock cover

Lock plate

Lock of Godrej/Harison

Locking vertical rod complete assembly

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for Tightening all loose parts, Preparation, cleaning of existing decorated surface/ rubbing by emery paper, removing all spot, filling with putty, painting for repaired and existing good furniture as directed at site, at furniture yard, Md, OTM buildings under AOR of GE.

Chair Verandah steel FD-359 and similar pattern: Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

Leg tube conduit complete without shoe

Seat/back short tube conduit

Seat/back long tube conduit

Horizontal rod below seat

Arm rest

Rubber shoe

Plastic white cane canning of seat

Plastic white cane canning of back

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparing old painted / new steel surfaces of chair verandah FD-359 including removing dents/spots (if any), tightening the loose joints, filling the gaps with putty, cleaning the surfaces, rubbing by emery paper and applying one coat of synthetic enamel paint on old painted surfaces and two coats on new / welded surfaces over a coat of red oxide primer as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Bed Hard steel MAP Drg No. FD/E6/MAP/08 (R) /similar pattern: Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

Plywood Top for sleeping

Stiffener

Head Leg without shoe

Foot Leg without shoe

Long rail

Short rail

Head rest particle Bd with MS frame complete

Foot rest particle Bd with MS frame complete

M&L for preparing old painted / new steel surfaces of bed steel MAP including removing dents/spots (if any), tightening the loose joints, filling the gaps with putty, cleaning the surfaces, rubbing by emery paper and applying one coat of synthetic enamel paint on old painted surfaces and two coats on new / welded surfaces over a coat of red oxide primer as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Charpoy GI Pipe Drg No. FD220 /similar pattern: Removing the existing unserviceable parts carefully without damaging / disturbing other parts and S&F following similar new parts including tightening of all loose parts etc complete all as specified and as directed by Engr-in-Charge:-

Long rail of GI pipe

Short rail converted from unserviceable long rail

Leg converted from unserviceable short rail

Elbows ISI marked

Checknuts ISI marked

MS Stiffner made of Flat Iron 25mm x 5mm and 900mm long including all fixing arrangements

Removing existing unserviceable ply top from frame of GI Charpoy, tightening / refixing the serviceable loose parts of frames and S&F new 12mm thick BWP grade Ply of size 900mm x 1980mm single piece, fixed with flush/counter sunk bolts 10 Nos of 5mm dia & 80mm long with two cup washers and nut. The hole in ply wood and GI pipe to be made of appropriate dia with drilling machine properly for fixing the ply with frame of charpoy complete all as specified and as directed.

Table bedside steel MAP Drg No. FD/E6/MAP/15R or similar pattern: Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

Rubber shoe

Drawer with handle

Channel (steel)

Door with handle

Hard top complete

Bottom sheet

Back sheet

Side sheet

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparing old painted / new steel surfaces of table bed side including removing dents/spots (if any), tightening the loose joints, filling the gaps with putty, cleaning the surfaces, rubbing by emery paper and applying one coat of synthetic enamel paint on old painted surfaces and two coats on new / welded surfaces over a coat of red oxide primer as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Charpoy MS folding steel Drg No. FD/388 (R) /similar pattern: Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

12mm Thick BWR grade Plywood Top for sleeping

Nut and bolt for Ply fixing

Gusset plate with fixing accessories

Flat iron strip with fixing accessories of size 25mm x 5mm thick as shown on drawing

Leg without shoe

Rubber shoe

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparing old painted / new steel surfaces of bed steel MAP including removing dents/spots (if any), tightening the loose joints, filling the gaps with putty, cleaning the surfaces, rubbing by emery paper and applying one coat of synthetic enamel paint on old painted surfaces and two coats on new / welded surfaces over a coat of red oxide primer as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Teapoy verandah steel FD-208, similar pattern: Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

Hard top complete

Leg frame complete without shoe

Rubber shoe .

Flat iron top frame complete

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparing old painted / new steel surfaces of teapoy verandah steel including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint on old painted surfaces and two coats on new /welded surfaces over a coat of red oxide primer as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Table 3'x2' steel FD-1008, 1007 and similar pattern:- Removing the existing unserviceable part and S&F following similar new part as per Drg and as directed by engr-in-charge.

Table top made of prelaminated particle board ext grade 18 mm thick

Rubber shoe

Top/Bottom long Stiffener

Top/Bottom short Stiffener

Drawer without lock

Lock for Drawer, make- Godrej, Harison (for FD-1008 only )

M&L for spot welding/run welding (not exc one inch in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparatiny old decorated / new steel surfaces of the table including removing dents/spots (if any), cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying two coats of synthetic enamel paint to give glossy finish including priming the new /welded surfaces as required complete all as specified and directed at furniture yard, Md / OTM accns under AOR of GE as directed by Engr-in-charge.

Table 3'x3' steel FD-1009 and similar pattern:- Removing the existing unserviceable part and S&F following similar new part as per Drg and as directed by engr-in-charge.

Table top made of prelaminated particle board ext grade 18 mm thick

Rubber shoe

Stiffener

M&L for spot welding/run welding (not exc one inch in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparatiny old decorated / new steel surfaces of the table including removing dents/spots (if any), cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying two coats of synthetic enamel paint to give glossy finish including priming the new /welded surfaces as required complete all as specified and directed at furniture yard, Md / OTM accns under AOR of GE as directed by Engr-in-charge.

Side Board ( Drg No- FD- 1112 /similar pattern. S&F following similar new part as per Drg and as directed by Engr-in-charge for day to day maintenance after removing the existing similar unserviceable part .

Shutter

Top complete

Left/right side ply complete

Drawer

Back ply complete

Knob as per sample.

Bottom frame with four leg made of 1st class well seasoned Teak wood

S&F, M&L for tightening all loose parts where ever possible. Preparation / cleaning of existing decorated surface/ rubbing by emery paper, removing all spots, filling with putty, polishing for repaired and existing good furniture.

Table office clerk steel FD-1004and similar pattern:- Removing the existing unserviceable part and S&F following similar new part as per Drg and as directed by engr-in-charge.

Table top made of prelaminated particle board ext grade 18 mm thick

Drawer without lock

Lock for Drawer, make- Godrej, Harison

Top/Bottom long Stiffener

Top/Bottom short Stiffener

Rubber shoe

M&L for spot welding/run welding (not exc one inch in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparatiny old decorated / new steel surfaces of the table including removing dents/spots (if any), cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying two coats of synthetic enamel paint to give glossy finish including priming the new /welded surfaces as required complete all as specified and directed at furniture yard, Md / OTM accns under AOR of GE as directed by engr-in-charge.

Table center wooden frame FD- FD-274, similar pattern. Removing the existing unserviceable part and S&F following similar new part as per Drg and as directed by Engr-in-charge.

stiffner complete at bottom

Leg without pvc ring

Long rail

Short rail

PVC Ring

bracket

Top particle board

Tightening all loose parts, Preparation/ cleaning of existing decorated surface/ rubbing by emery paper, removing all spots, filling all cavity with putty, polishing for repaired and existing good furniture at furniture yard/Md/OTM buildings under AOR of GE as directed by Engr-in-Charge.

Teapoy wooden FD-278 and similar pattern:- Removing the existing unserviceable part and S&F following similar new part of well seasoned Ist class hard wood (Teak) as per Drg and as directed by Engr-in-charge.

Table top made of prelaminated particle board ext grade 18 mm thick

Leg without PVC ring

Long rail

Short rail

PVC ring

Bracket

M&L for preparing old decorated / new wooden surfaces by removing all spots, filling all cavities with putty, rubbing with emery paper to smooth the surfaces and applying two or more coats of french polish to give shiny finish including filler coat on new wooden surfaces (if required) complere at furniture yard / Md / OTM buildings under AOR of GE as directed by Engr-in-Charge.

Book shelf open large steel FD-69/ similar pattern:- Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

Top/shelf/bottom sheet

MS slot iron

left/right sides sheets

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparing old painted / new steel surfaces of book shelf open large steel including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint on old painted surfaces and two coats on new /welded surfaces over a coat of red oxide primer as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Hat stand with mirror FD-361, /similar pattern. S&F following similar new part as per Drg and as directed by Engr-in-charge for day to day maintenance after removing the existing similar unserviceable part .

Mirror with beading

front veneer

back sheet

beading complete

hanging Clip

S&F, M&L for tightening all loose parts where ever possible. Preparation / cleaning of existing decorated surface/ rubbing by emery paper, removing all spots, filling with putty, polishing for repaired and existing good furniture.

Chair cushioned with arm, without arm, fixed, revolving FD-75/TP/similar pattern: Removing the existing unserviceable parts and S&F following similar new parts as per Drg and as directed by Engr-in-Charge:-

Complete seat

Complete back

Revolving assembly at seat bottom complete with verticle fitting

Chair base complete without castor

Castor best quality

Arm rest best quality

Base steel frame of arm rest

bottom frame complete for non revolving chair

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish complete all as specified and directed. Note:- The welding required for fixing of new parts will not be measured against this item. The same to be treated as included in rates of the new part.

M&L for preparing old painted / new steel surfaces of chair cushioned steel including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint on old painted surfaces and two coats on new /welded surfaces over a coat of red oxide primer as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

VARAROHA BUILDERS

M/s R.K.Jain

CITIZEN FURNITURE INDUSTRIES