Construction of Mini Secretariate Building at Indora, Tehsil Indora Distt.Kangra H.P.

Amount

Earth work in Excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as direction of Engineer-in-Charge and returning the stcked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etcetera; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete as per directions and entire satisfaction of engineer in charge including carriage of material within all leads , lift and other incidentals . The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and any taxes imposed by government

Providing form work with steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frames 30x30x5mm (Thirty isto thirty isto five millimetre) so as to give a fair finish including centring, shuttering, strutting and heights propping etcetra with wooden battens and ballies heights of propping and centring in all below supporting floor to ceiling upto any height and removal of the same for insitu-reinforced concrete and plain concrete work in Foundation Footings, basis of columns etcetra and mass concrete including entire carriage of materials with in all leads, lifts and other incidential as per drawings and technical specifications and as per the direction of Engineer-in-Charge .The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frames 30x30x5mm (Thirty isto thirty isto five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies,heights of propping and centring in all heights/depths below supporting floor to ceiling upto any height and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings,balconies and access platform, shelves and the like floor etcetera In all thickness upto all floor level including entire carriage of materials with in all leads,lifts and other incidential as per drawings and technical specifications and as per the direction of Engineer-in-Charge.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with mild steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frames 30x30x5mm (Thirty isto thirty isto five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, heights of propping and centring in all heights/depths below supporting floor to ceiling upto any height and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels Sides and soffits of beams,beam haunchings, cantilevers, girders, bressumers and lintels upto any height/depth upto all floor level including entire carriage of materials with in all leads, lifts and other incidential as per drawings, technical specifications and as per the direction of Engineer-in-Charge.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frames 30x30x5mm (Thirty isto thirty isto five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies heights of propping and centring in all heights below supporting floor to ceiling upto any height and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, Pillars,Piers,Abutment,Posts and struts upto all floor level including entire carriage of materials within all leads lifts and other incidential as per drawings, technical specifications or as per the direction of Engineer-in-Charge.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with mild steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frames 30x30x5mm (Thirty isto thirty isto five millimetre) so as to give a fair finish including centring, shuttering, strutting, propping etcetra with wooden battens and ballies, heights of propping and centring in all heights below supporting floor to ceiling upto any height and removal of the same for insitu-reinforced concrete and plain concrete work in Stair Cases with sloping or upto all floor level including entire carriage of materials with in all leads,lifts and other incidentials as per drawings and technical specifications and as per the direction of Engineer-in-Charge.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with mild steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frames 30x30x5mm (Thirty isto thirty isto five millimetre) so as to give a fair finish including centring, shuttering, strutting, propping etcetra with wooden battens and ballies, heights of propping and centring in all heights below supporting floor to ceiling upto any height and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls width upto all floor level including entire carriage of materials within all leads, lifts and upto any other incidential as per drawings and technical specifications and as per the direction of Engineer-in-Charge .The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty isto Thirty isto Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Weather shade, Chajjas, corbels etcetera including edges upto all floor level including entire carriage of materials within all leads, lifts and upto any other incidential as per drawings and technical specifications and as per the direction of Engineer-in-Charge .The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty isto Thirty isto Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like upto all floor level including carriage of materials within all leads, lifts and upto any other incidential as per drawings and technical specifications and as per the direction of Engineer-in-Charge .The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty isto Thirty isto Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etcetera upto all floor level including entire carriage of materials within all leads, lifts and upto any other incidential as per drawings and technical specifications and as per the direction of Engineer-in-Charge .The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:4:8 (one cement :four coarse sand : eight graded stone aggregate 40mm ( forty milimetre nominal size) and curing complete excluding cost of form work in foundation and plinth in all depth as per HPPWD specification, approved Drawings, design as per the entire satisfaction and direction of Engineer in charge including carriage of material within all leads lifts and other incidentals.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Filling in plinth with stone filling under floors including watering ramming , consoldating and dressing complete as per approved drawing , design, specification as per directions and entire satisfaction of engineer in charge including carriage of material within all leads , lift and other incidentals . The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and any taxes imposed by Government

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with cement mortar 1:6 (one cement isto six sand) in all heights/depths or as per the direction of Engineer-in-Charge including carraige of materials with in all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the ccompressive strength of 25N/mm2 (Twenty five Newton per square millimetre) for reinforced cement concrete work with cement contents not less than 360 kg (Three hundred sixty kilogram) per cubic metre or as per approved design mix for work upto plinth level to give a smooth surfaces mechanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for reinforced concrete work complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the ccompressive strength of 25N/mm2 (Twenty five Newton per square millimetre) for reinforced cement concrete work with cement contents not less than 360 kg (Three hundred sixty kilogram) per cubic metre or as per approved design mix for work upto plinth level to give a smooth surfaces mechanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for reinforced concrete work complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, GST and any other taxes imposed by the Government.

Providing and laying Tor/mild Steel reinforcement Thermo-Mechanically Treated bars of Tata, Tiscon/sail grade Fe-500D or more.for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level to all floor level complete as per HPPWD specifications, approved Drawing,design, as per the entire satisfaction and direction of Engieer in charge including carriage of material within all leads lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Providing and laying damp proof course 100mm ( One hundred millimetre) thick with cement concrete 1:2:4 (one cement: two sand:four stone aggregate) 20mm ( Twenty millimeter) nominal size and curing complete as per entire HPPWD satisfaction, approved drawing, design or as per the entire satisfaction and the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing Applying a coat of hot bitumen mexphalt 80/100 ( Eighty / one hundred) using 1.70 kg.(one decimal seven Kilogramme per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil complete as per HPPWD specifications, approved Drawing design or as per the entire satisfaction and the direction of Engineer-in-Charge. Including carriage of materials within all leads, lifts and other incidental.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Half brick masonry using second class common burnt clay building bricks in super structure above plinth level upto floor all level in Cement Mortar 1:4 (One Cement isto Four Sand) and curing complete as per entire satisfaction and the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Brick work using second class common burnt clay building bricks in super-structure above plinth level upto all floor level in Cement Mortar 1:6 (one Cement isto six Sand) and curing complete as per approved drawing design specofications and as per direction and entire satisfaction of the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and other taxes imposed by the Government.

Providing and fixing M.S. channels Frames 75 X 40 X 4 mm (Seventy Five isto Forty isto Four millimeter) M.S. angle iron25 X 20 X 3 mm (Twenty Five isto Twenty isto Three millimeter) for doors, windows, frames manufactured from M.S. T - section 25 mmx 25 mmx 3 mm (Twenty Five millimeter isto Twenty Five millimeter isto Three millimeter) and Z- Sections with M.S. flat 75mmx4mm (Seventy five millimeter isto Four millimeter) in combination as per drawing, design including hinges, jamb, lock jamb beed and if required thrashold i/c thrashold of M.S. angles means lugs, with split and tails to each jamb including iron butt hinges 2.5mm thick with a provision of locking arrangement and shock observers as specified and applying a coat of approved steel primer after pre-treatment of the surface and direction by the Engineer-In-Charge including carriage of material with in all lead, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Colured anodised aluminium ( anodised transparent or dyed to required shade accoeding to IS:1868. Minimum anodic coating of grade AC 15) sub frame work for door, windows and ventilators of section No 14081 of Jindal/Hindalco with extruded built up standard tubular sections, fixed with dash fastener and required dia and size As per specification, Drawing, design and direction by the Engineer-In-Charge with in all lead, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing coloured aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of of Jindal /Hindalco approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etcetera. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required. As per specification , Drawing and Direction by the Engineer - In -Charge.(Fittings shall be paid for separately)Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15) complete and as per the direction of Engineer-in-Charge including carriage of material with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing wire fly proof stainless steel ( Grade 304) wire guage of 0.5mm ( Zero point five millimeter) dia wire and 1.4mm aperture on both side in windows, clerestory windows and doors with S.S Flat 15x3mm ( Fifteen isto Three millimeter) and bolts complete as per approved drawing design specifications the direction of Engineer-in-Charge including carriage of material with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing aluminium (Zindal/ Hindalco make) anodized powder coated 8mm ( Eight Millimeter) thick of Zindal/ Hindalco (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. (Only weight of grill to be measured for payment) complete as per approved drawing design specification and and as per the direction of Engineer-in-Charge including carriage of material with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 12 mm ( Twelve Millimeter) thick prelaminated phenol board (Both side) in Matt finishing of action tissa/ grabin/ merinolam/ kittan/ bista approved shade particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etcetera complete as per architectural drawings, deisign, specificition and directions of engineer- in-charge including carage of material with in all leads , lifts and other incidentals.The rate is including of octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Providing and fixing to existing door frames, 30mm (thirty millimetre) thick factory made PVC panelled door shutter ( code No. 9.120) of Rajshri consisting of frame made out of M.S. tubes of 19 (nineteen) gauge thickness and size of 19mm x19mm (ninteen millimeter isto ninteen millimetre) for styles and 15mmx15mm (fifteen millimeter isto fifteen millimetre) for top and bottom nails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm ( five millimeter) thick heat moulded PVC "C" channel of size 30mm (thirty millimetre) thickness, 70mm (seventy millimetre) width cut of which 50mm (fifty millimetre) shall be flat and 20mm (twenty millimetre) shall be tapper in 45 degree angle on either side forming style and 5mm (five millimetre) thick, 95mm (ninty five millimetre) wide, PVC sheet out of which 75mm (seventy five millimetre) shall be flat and 20mm (twenty millimetre) shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm (one hundred fifteen millimetre) wide PVC sheet out of which 75mm (seventy five millimetre) shall be flat and 20mm (twenty millimetre) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (ten millimetre) thick, 20mm (twenty millimetre) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm (five millimetre) thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges with necessary screws etcetera complete as per approved drawing, design specifications and as per the direction of Engineer-in-Charge including carriage of material with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Providing and fixing 25mm (twenty five millimetre) thick ply board water proof ISI marked of kitlam/kitply/Tessa shutter (Century ply) with 6 mm (six millimetre) thick hard wood edging all around and 0.63 mm (zero decimal six three millimetre) thick P.G.I sheet lining in side fixed with piano hings with screw complete and as per approved drawing, design specifications and the direction of Engineer-in-Charge including carriage of material with in all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing glazing Modi Guard/Saint Gobain in aluminium doors, window, ventilators shutters and partition with PVC/Neoprene gasket etc. complete in glazing with glass pans of 6.00 mm (Six millimetres) thickness weight not less than 15 kg (fifteen kilograme) per square metre of Modi Guard/Saint Gobain and as per approved drawing, design specifications and the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Providing and fixing glazing with glass pans of 5.00 mm (five millimetre) thickness weight not less than 12.50 kg (twelve point fifty kilograme) per square metre (Modi Guard/Saint Gobain) in aluminium door, window,ventilator shutters and partition etc with PVC/neoprene gasketetcetera. complete as per the architectural drawings design specification and as per the direction of Engineer-in-Charge including carriage of material with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Providing and fixing 5 mm (five millimetre) thick weight not less then 12.50 kg/sqm (twelve point fifty kilograme Per Square meter) frosted glass panes of Modi Guard/Saint Gobain in aluminium door, window, ventiation, shutter and partition etectera with PVC/necessary gasket etcetera complete in jointing complete as per approved drawing, design specification and as per the direction of Engineer-in-Charge including carriage of material with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 20mm (twenty millimetre) dia stainless steel curtain rod having well thickness of 1.25mm ( One Point Twenty Five Millimeter) with two stainless steel brackets fixed with C.P Brass screws and P.V.C sheeves etcetera wherever necessary complete as per approved drawing, design, specifications and as per directions and entire satisfaction of engineer in charge including carriage of material within all leads , lift and other incidentals . The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and any taxes imposed by Government.

Providing and fixing 300x16mm ( Three Hundred isto Sixteen Millimeter) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetera complete as per approved drawing, design, specifications and as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminium tower bolts, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per approved design, specification and as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

(i) 200x10mm ( Two Hundred isto Ten Millimeter)

(ii) 150x10mm ( One Hundred Fifty isto Ten Millimeter)

Providing and fixing aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per approved design, drawing, specification and as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

(i) 150mm ( One Hundred Fifty Millimeter)

(ii) 125mm ( One Hundred Twenty Five Millimeter)

Providing and fixing 150mm ( Two hundred Fifty Millimeter) aluminium hooks and eges ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etcetera complete as per approved drawing, design, specifications and as per directions and entire satisfaction of engineer in charge including carriage of material within all leads , lift and other incidentals . The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and any taxes imposed by Government.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body and door with necessary accessories and screws etcetera complete as per approved drawing, design, specification and as per directions and entire satisfaction of engineer in charge including carriage of material within all leads , lift and other incidentals . The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and any taxes imposed by Government.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etcetera complete as per approved design, specification and as per directions and entire satisfaction of engineer in charge including carriage of material within all leads , lift and other incidentals . The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and any taxes imposed by Government.

Providing and fixing the complete box of cup board sahll be made of 25mm (Twenty Five millimetre) thick water proof termite resistant ply board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino ISI marked including shelves.Back side of board shall have 6 to 8 mm (Six to eight millimetre) thick water proof ply all the cut portion of board shall have 6 mm (Six millimetre) thick hard wood edging/ eighing. The shutter from all side shall be finished with 1mm thick lamination ISI Marked of approved shade of Century / Greenlam /Action Tesa/Merinalum and 19 mm (Nineteen millimetre) thick shelves water proof board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino including hinges, PTMT handle in wood colour of Prayag Polymers,knob megnatic catcher complete the onter face of cup boaed shall be measured for as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mirror polished 25 mm ( Twenty five millimeter) thick Kota stone minimum Size 55X55cm ( Fifty five isto Fifty five centimeters) / 55 X 27.5 cm (Fifty five isto Twenty seven point five centimeters) of uniform colour with 7.5 cm ( Seven point five centimeter) wide Jaislmer Yellow marble band of same shade that of flooring/skirting of approved shade as per detail slab flooring over 20 mm ( Twenty millimeter average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including curing rubbing and polishing complete with base of cement mortar 1 : 4 ( One cement isto four coarse sand) complete as per drawing, design, specifications and as per the entire satisfaction and direction of Engieer in charge including carriage of material within all leads, lifts and other incidentals. The rate is including of octroi,royality, malkhana toll tax, sale tax, G.S.T and any other texes texes imposed by the Government.

Providing and fixing 19 mm ( Ninteen millimeter) thick Pink Granite in combination with Black Granite in flooring/skirting premoulded and prepolished, machine cut for kitchen platforms, vanity counters, and similar locations of required size, approved shade, colour and texture laid over 20 mm ( Twenty Millimeter) thick base cement mortar 1:4 ( One cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etcetera complete at all level as per approved drawing, design, specification and direction of the Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.The rate is including of octroi,royality, malkhana toll tax, sale tax, G.S.T or any other texes imposed by the Government.

Providing and laying size of tiles 600mm x 600 mm ( Six hundred millimter isto Six hundred millimeter) full body Matt finish vitrified floor tiles of RESTILE/JOHNSON/ NITCO/RAK/KAJARIA,AGL , SOMANY/SIMPOLO/ORIENTAL/BELL in flooring as per approved shade and design of the office ( thickness to be specified by the manufacture) with water absorption less then 0.08% and conforming to IS: 15622 of approveed make, in all colours and shades, laid on 20mm ( Twenty millimeter) thick cement mortar 1:4 ( One cement isto four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including curing grouting the joints with white cement and matching pigments etcetra, complete as per approved drawing, design, specification and direction of the Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including the octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

Providing and Laying size of tiles 600mm x 600 mm ( Six hundred isto Six hundred millimeter) double charge/ultra charged vitrified floor tiles of RAK/ JOHNSON/ NIRCO/ KAJARIA/ AGL/ SIMPOLO/ SOMANY/ ORIENT & BELL as per approved shade and design of the office ( thickness to be specified by the manufacture) with water absorption less then 0.08% and conforming to IS: 15622 of approveed make, in all colours and shades, laid on 20mm ( Twenty millimeter) thick cement mortar 1:4 ( One cement isto four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etcetra, complete as per approved drawing, design, specification and direction of the Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including the octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

Providing and laying Precast terrazzo tiles automatic Hydraulic compressed and polished Terrazzo tiles of NTC/ Unistone/ Atlantic in flooring size 30cmx30cmx2.5cm (Thirty centimetre isto Thirty centimetre isto two decimal five centimetre) ISI marked No IS: 1237 top layer in (50%) (Fifty Percent) white and 50% (Fifty percent) Grey cement ) in white yellow , green and maroon chips of size 0,B and 2B size of NTC/ unistone/ atlantic as per approved shade with marble chips of specified sizes laid on a bed of 20mm (Twenty millimetre) average thickness of cement mortar 1:4 (one cement isto four sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (where ever required) including curing rubbing and polishing complete as per specifications, approved drawing and design including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying 300x300mm (three hundred isto three hundred millimeters) Antiskid Ceramic tiles of premimum quality of NITCO/KAJARIA /JOHNSON /AGL/SOMANY/ORIENT and BELL in flooring laid over 12mm (Twelve millimeters) thick cement mortar 1:4 ( One cement isto four coarse sand ) including curing , jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level in all heights as per approved specifications, drawing, design and as per the direction and entiresatisfaction of the Engineer-in- charge including carriage of material within all leads, lifts and other incidentals The rate is including of octroi,royality, malkhana toll tax, sale tax, G.S.T and any other texes imposed by the Government.

Providing and laying 300x300x25mm (Three hundred isto three hundred isto twenty five millimetre) labrador design(Rainbow series ) of NTC / Unistone / Atlantic slab flooring in ramp over thick on 20mm (twenty millimetre) average thick base of cement 1:3 (One cement isto three coarse sand) including curing rubbing and polishing, cutting and moulding complete as per approved drawing, design, specification including carriage of materials within all leads, lifts and other incidentals.The rate is including of octroi,royality, malkhana toll tax, sale tax, G.S.T and any other texes imposed by the Government.

Smooth finishing of the exposed surface of R.C.C. work with 6 mm (Six millimeter) thick cement mortar 1:3 (One Cement isto Three fine sand) complete as per approved drawing, design, specification and the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 19 mm ( Ninteen millimeter) thick Grey /Chima Pink Granite single slab with semi round nosing in work steps, approved shade, colour and texture laid over 20 mm ( Twenty Millimeter) thick base cement mortar 1:4 (One cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etectra complete at all level complete as per approved drawing, design, specification and direction of the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.The rate is including of octroi,royality, malkhana toll tax, sale tax, G.S.T and any other texes imposed by the Government.

Providing and laying 80mm (Eighty millimetres)thick factory made cement concrete interloking blockof NTC/UNISTONE/ATLANTIC as per approved design and shade heavy duty precasts cement concrete interlocking paver blocks vibro compacted upto M-50 ( M-Fifty) gradeincluding border or kurb block grey or coloured ever sub base of concrete with 25mm (Twenty five millimetres)thick average thickness of cement mortar 1:4(One cement isto four coarse sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of block including curing rubbing polishing completeas per HPPWD specifications,approved Drawing,design as per the entire satisfaction and direction of Engieer in charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and any taxes imposed by Government.

Providing and laying full body matt finish Vitrified tiles of Restile /Johnson/ Nitco/Kajaria / AGL / Simpolo / Somany /Orient & Bell as per approved shade and design of the office Size of Tile 600 mm x600 mm (Six Hundred millimter isto Six hundred millimeter)sqm (thickness to be specified by the manufacturer), with water absorption less than 0.08% (zero point zero eight percent) and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints complete as per HPPWD specifications,approved Drawing,design as per the entire satisfaction and direction of Engieer in charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst or any taxes imposed by Government.

Providing and laying Double Charge / Ultra Charge Vitrified tiles of Restile/ Johnson/ Nitco/Kajaria / AGL / Simpolo / Somany /Orient & Bell as per approved shade and design of the office Size of Tile 600 mm x600 mm ( six hundred millimter isto six hundred millimeter)sqm (thickness to be specified by the manufacturer), with water absorption less than 0.08% (zero point zero eight percent)and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including curing grouting of joints complete as per HPPWD specifications,approved Drawing,design as per the entire satisfaction and direction of Engieer in charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi , royality , malkhana , toll tax , sale tax , Gst and other any taxes imposed by Government.

Providing and laying Precast terrazzo tiles automatic Hydraulic compressed and polished Terrazzo tiles of NTC / Unistone / Atlantic in skirting size 30cmx10cm (Thirty centimetre isto ten centimetre) ISI marked No IS: 1237 top layer in (50%) (Fifty Percent) white and 50% (Fifty percent) in white yellow green and maroon chips of size 0 , B and 2B sizes of Ntc with marble chips of specified sizes laid on a bed of 12mm (Twelve millimetre) average thickness of cement mortar 1:3 (one cement isto three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (where ever required) including curing rubbing and polishing complete as per specifications, approved drawing and design including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the Government.

Providing and laying 300 mm x450 mm (Three hundred millimeter isto Four hundred Fifty millimeter) Ceramic Glazed floor tiles of Kajaria / Johnson /Swastik /Bell / Somany / AGL with one border matching contrast at top in skirting and Dado as per approved shade (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (One Cement isto Four Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilograme per square meter) including grouting the joints with white cement and matching pigments etcetera complete as per specifications, approved drawing and design including cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the Government.

Providing and laying 300 mm x450 mm / 300mm X 600 mm (Three hundred millimter isto four hundred fifty millimeter / three hundred millimeter isto six hundred millimeter) Ceramic Glazed floor tiles of Kajaria /Swastik /Bell / Somany / AGL in skirting risers and steps and dado (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (One Cement isto Four Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilograme per square meter) including curing grouting the joints with white cement and matching pigments etcetera complete as per specifications, approved drawing and design including cost and carriage of materials, with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the Government.

Providing and fixing 19 mm ( Ninteen millimeter) thick Chima pink Granite in treads with round nosing/ Riser of steps gang saw cut, mirror polished, premoulded and prepolished, machine cut required size, approved shade, colour and texture laid over 20 mm ( Twenty Millimeter) thick base cement mortar 1:4 ( One cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etcetera complete at all level as per approved drawing, design, specifications and direction of the Engineer-in-charge, including carriage of materials with in all leads, lifts and other incidentals.The rate is including of octroi,royality, malkhana toll tax, sale tax, G.S.T or any other texes imposed by the Government.

Providing and laying 8 mm ( Eight millimeter) thick Teak ply peneling over 50 x 31 mm ( Fifty one isto thirty one millimeter) soft wood grid frame work at 600 mm ( Six hundred millimeter) C/C with decorative teak wood beading over teak ply of size 25 X 12 mm ( Twenty five isto Twelve millimeter) having moulding on both side cornice / edging on top of peneling to be finished with 55 X 30 mm ( fifty five isto thirty millimeter) teak wood beading as per detail ,drawing and specification as per the entire satisfaction and direction of Engieer in charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi,royality, malkhana toll tax, sale tax, G.S.T and any other texes imposed by the Government.

Providing and fixing acoustical panels of 600 mm x1200 mm x25 mm( six hundred millimter isto twelve hundred millimter isto twenty five millimeters) of dexune acoustical/ Prolad Himalyan panels fixed with steel screw as per detail drawing and specification as per direction of Engineer-In -Charge including carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive toll tax, GST and any other taxes imposed by the Government.

Providing and fixing 0.60mm ( Zero point Six Zero millimetre) thick prepainted steel sheet ( ISI Marked Z-120) of TATA/DURASHINE/SAIL/RELIANCE/JINDAL over steel trussed in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 ( Twenty ) microns over 5 ( five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm ( Six millimetre) diametre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge as per approved drawing , design, specifications including carriage of materials within all leads, lifts and other incidental.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing pre-painted steel sheet ridge ( Factory Made) having proper Gola shape and hips of TATA Durashine/ Sail / Reliance / Jindal 60cm (sixty centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns primer coating + back coating of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia prepainted bitumen washers complete in all respect as per approved specifications, drawing and design including cost and carriage of material, with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providig and Fixing pre-painted sheet valleys 90 c.m ( Ninety Centimeter) over all with 0.60mm ( Zero decimal six zero millimeter) thick prepainted sheet in roofing of TATA/DURASHINE/SAIL/JINDAL/RELIANCE with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns primer coating + back coating of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia prepainted bitumen washers complete in all respect as per approved specifications, drawing and design including cost and carriage of material, with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 30cm (Thirty centimetre) wide 25cm (Twenty five centimetre) deep plain G.I. sheet gutter of 0.60mm (zero decimal six zero millimetre) thick sheet fixed with bolts, nuts and washers etcetra having dome shape gratting which shall be of MS flat 25 X 5/6 mm SQ ( Twenty five isto Five/Six Millimeter) / round bar and 6mm ( Six Millimeter) round bars in dome including making necessary connections with rain water pipe complete including cost and carriage of material, with in all leads, lifts and other incidentals as per specifications, approved drawing and design, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing M.S. B.P. sheet 2 mm (two millimetre) thick of TATA/DURASHINE/ SAIL / Reliance / Jindal for eaves board/Facia/Soffit/Ceiling including cutting, fixing and jointing with gass/electric welding with steel roof member and applying a coat of red lead primer complete as per PWD specification, approved drawing and design (frame work is to be measured and paid for separately) including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing flashing 38cm (Thirty eight centimetre) overall with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet of Tata/Durashine/sail/ Reliance/Jindal with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia meter & prepainted G.I. limpet & bitumen washers complete in all respect as per approved specifications, drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150 mm (One hundred fifty millimetre) diametre high pressure P.V.C spigot and socket pipe of Finolex/Vectus /Relpipe (reliance)/Supreme/Prince working pressure not less than 4/6 kg (Four/Six kilograme) I.S.I Marked including fixing with approved adhesive etcetra complete as per approved drawing, design, specification and direction by the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals.The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the Government.

Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes of Finolex/Vectus /Relpipe (reliance)/Supreme/Prince including filling the joints with approved adhesive complete as per PWD specification, approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- in-Charge. The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the Government.

150mm (one hundred fifty millimetre) dia PVC plain bend

150mm (one hundred fifty millimetre) dia PVC shoe

Providing and fixing unplasticised -PVC pipe clips P.V.C Holder bat clamps of Finolex/Vectus /Relpipe (reliance)/Supreme/Prince approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty isto fifty isto fifty millimeter) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (One cement : Four coarse sand) and making good the wall etcetera complete as per PWD specification, approved drawing and design including cost and carriage of material, with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- in-Charge. The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the Government.

Structural steel of Tata / Sail work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per PWD specification, approved drawing and design including carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- in-Charge.The rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the Government.

Providing water proofing treatment shall be done in two coats apply First coat of Dr. Fixit Torch SHIELD ( P - 3160- 3mm ) to the clean and saturated surface maintaining a coverage 0.60 sqm (Zero point six zero squate meter) per kilogram to achieve 1mm (one millimeter) thickness this coating shall also be executed up to 300mm vertically. The 2nd coat shall be applied in opposite direction after 4 to 6 (Four to six) hours of application of 1st coat then sprinkle sand on top surface of applied Dr. Fixit Fast flex white still tacky and the second coat. Then apply cement mortar 1:4 (one cement ist four sand) and mixed with Pidiproof LW at the rate 200ml (two hundred millimetre) per 50 (Fifty kilogram) of cement over the floor with suitable gradient towords drain water pipe while the second coat of Dr. Fixit is still tacky.complete as per approved drawing, design, specifications including carriage of materials, within all leads, lifts and other incidental, and as per directions of Engineer-in-Charge. The rate is including Royality, Malkana, Octroi, Toll Tax, Sales tax, GST and any other taxes imposed by the Government.

Providing and fixing hand rail of 50 mm (Fifty millimeter) dia SST stainless steel pipe handrail fixed with 35 mm (Thirty Five millimeter ) dia sst pipe as per detail in combination of 35 mm (Thirty Five millimeter) dia and 15 /20 mm(Fifteen/Twenty millimeter) sst baluster complete in all respect as per approved drawing, design, specifications including carriage of materials within all leads, lifts and other incidental, and as per directions of Engineer-in-Charge. The rate is including Royality, Malkana, Octroi, Toll Tax, Sales tax, GST and any other taxes imposed by the Government.

Providing and fixing hand rail 50mm ( Fifty Millimeter) dia. SST hollow pipe handrail slip resistant with round ends at two levels at 75 Cm & 90cm Ht. It should entend 30 c.m ( Thirty Centimeter) beyond the top and bottom of the ramp as per detail welded to 25 cm ( Twenty five centimeter) dia SSt hollow pipe baluster welded to 50mm ( Fifty mMillimeter) dia Pipe embadded in cement concrete 600mm ( Six hundred millimeter) C/c as per detail design PWD specifications of approved size by welding etcetera to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Painting Steel work with Deluxe Multi Surface Paint of Asian / Nerolac to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm ( zero point ninety liter per ten square meter) over an under coat of primer applied @ 0.80 ltr/ 10 sqm (zero point eighty litre per ten square meter) of approved brand and manufacture complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Applying priming two or more coats with ready mixed pink or grey primer of Paint of Asian / Nerolac required shade on wood work complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Painting wood work with Deluxe Multi Surface Synthetic enamel Paint of Asian / Nerolac required shade. Two or more coat applied @ 0.90 ltr/10 sqm ( zero point ninety liter per ten square meter) over an under coat of primer applied @0.75 ltr/10 sqm (zero point seventy five litre per ten square meter) of approved brand and manufacture complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 12mm (twelve millimetre) thick Unistone / NTC / Atlantic stone cladding on wall surface with 12mm ( twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) and jointed with cement slurry to match the stone including scaffolding curing complete as per approved drawing, design, specifications including carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- In-Charge .The rate is including of toll tax, GST and any other taxes imposed by the Government.

6mm( Six millimetre) thick Cement plaster to ceiling with Cement mortar 1:3( One Cement isto three Sand) complete upto all floor level curing complete as per entire satisfaction and the direction of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental.The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x600x16mm (Six hundred isto six hundred isto sixteen millimetre) dune RH 99 tiles of armstrong mineral fiber tiles of gyproc with wood wool backing 50mm thick layer and fix with power coated T-Grid work @ 600 (Six hundred) centre to centre in combination with 150x12mm (One hundred fifty isto twelve millimetre) thick RAI wood border as per pettern complete as per specifications including carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive toll tax, GST and any other taxes imposed by the Government.

Providing and fixing 595 mm x595 mm x6 mm (Five hundred ninety five millimeter isto fiive hundred ninety five millimeter isto six millimetre) designer board of everest ( E-Board) ceiling with pre-painted GI channel framing @ 600 mm c/c (Six hundred millimetre centre to centre) complete including curing as per PWD specification,approved drawing, design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of toll tax, GST and any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6 (one cement isto Six sand) in single coat on rough side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth curing complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6 (one cement isto Six sand) in single coat on fair side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even, smooth and curing complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:4 (one cement isto four coarse sand) in single coat on fair side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even, smooth and curing complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 20 mm( Twenty Millimeter) Thick Pattern in cement Plaster including grave With cement Mortar :1:4 (1cement: 4 coarse sand) curing complete as per approved drawing, design, specifications as per direction and entire satisfaction of engineer in charge including carriage of material with in all leads , lift and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and applying 15 mm ( Fifteen millimeter) thick cement plaster with cement mortor 1:3 ( One cement isto three sand) in single coat on rough side of brick /concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even, smooth and curing complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying white cement based putty of Birla / JK average thickness 1 mm ( One Millimeter) of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete with in all leads , lift and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Finishing wall with Apex weather proof exterior grade emulsion of paint of ( ASAIN/NEROLAC/BERGER/DULUX/SURAKSHA paints of approved shade having VOC less then 50gm/litre and UV reistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives on wall New work (Two or more coats applied @ 1.43 litre/ 10 sqm (One point forty three litre per ten square meter) Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point nine zero litre per ten square meter) as per approved drawing, design, specification and direction of the Engineer-in-charge including carriage of material with in all leads, lifts and other incidential. The rate is including of octroi, royality, Malkana, toll tax, GST and any other taxes imposed by the Government.

Painting two or more with acrylic washable emulsion of Asian / Dulux / Berger / Nerolac paints based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting two or more with premium emulsion of Asian / Dulux / Berger / Nerolac paints based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GSTand any other taxes imposed by the Government.

Painting two or more with acrylic emulsion of Asian / Dulux / Berger / Nerolac paints based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing plinth protection with 40 mm (Forty millimetre) thick heavy duty precast cement concrete interlocking paver block of NTC/UNISTONE/ATLATICA with 23 cm (twenty three centimetre) diametre half round stone ware pipe for drainage purpose laid over 10mm (Ten Millimetre) thick cement concrete 1:4:8 (one cement isto Four sand isto Eight graded crushed stone aggregate 40 mm (Forty millimetre) nominal size bedding/haunching for pipe complete as per approved drawing/design and specification and as per the direction of Engineer-in-charge including carraige of materials with in all leads, lifts and other incidentials.The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and Laying Green Marble work gang saw cut (polished and machine cut) of thickness 19 mm (Ninety millimeter) for wall backing filled with a grout of average 12 mm (Twelve millimeter) thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately)Area of slab over 0.50 sqm (zero point five zero square meter) complete as per approved drawing/design and specification and as per the direction of Engineer-in-charge including carraige of materials with in all leads, lifts and other incidentials.The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government

Providing and fixing Dias and other two side's table shall be made of 19 mm (Nineteen millimeter) thick commercial board including Drawars, vertical portion and cabinet work. The table TOP shall be made of 25 mm (twenty five millimeter) thick commercial board. The table top dias, vertical partitions of table towards the public side and all other sides towards sitting shall be finished with 3 mm (Three millimeter) thick green panel max creative veneer VO-II cherry pine up laminating to be polished in teak wood natural shade. All visible portions of commercial board shall be finished with hard wood edging of 12 mm (Twelve millimeter) thick and 19 mm (Nineteen millimeter) wide.The table shall have hard wood beading/ edging and out of 50x25 mm ( fifty into twenty five milimetre) on three side complete as per drawaing, design specification and as per direction of Engineer -in - Charge including carriage of materials with in all leads, lift and other incidentials .The measurment for the payment shall be made for exposed faceonly.The rate is inclusive of all type of taxes imposed by the the Government.

Excavating trenches of required width for pipes, cables, etcetera including excavation for sockets, and dressing of sides, ramming of bottoms upto all depth , including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm ( twenty centimeter) in depth, including consolidationg each deposited layer by ramming, watering etcetera and disposing of surplusexcavated soil material as per approved specification drawing design as per entire satisfaction and as per the direction of Engineer-in-charge including carraige of materials with in all leads, lifts and other incidentials.The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and Fixing Charomium plated 40mm (forty millimetres) dia steel pipe for grab bars at 78cm (seventy eight centimetres) height M.S. plate as per details at the position of the seat and Wash Basin complete as per the direction of Engineer including carriage of materials with in all leads, lift and other incidentials .The measurment for the payment shall be made for exposed faceonly.The rate is inclusive of all type of taxes imposed by the the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (M-Twenty) design mix to obtain the compressive strength of 20N/mm2 (Twenty newton per square millimetre) for reinforcement concrete work with cement content not less than 330 kg (Three hundred thirty kilogramme) per cubic metre or as per approveddesign mix for work upto plinth level to give a smooth surfaces mechnically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixture in recommended proportion as per IS:9103 to accelerate, retard setting of concrete improve workability without imposing strength and durability for all works above plinth level to all floor level as per approved drawing,design and as per the direction of Engineer-in-Charge including carraige of materials with in all leads, lift and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Squared rubble masonary ( first sort) coursed with hard stone in foundation and plinth of approved quality in foundation and plinth including racking out joint in cement mortar 1:5 (one cement isto five sand) in all heights/depths or as per the direction as per the direction of Engineer-in-charge including carraige of materials with in all leads, lifts and other incidentials.The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing witness box consist of shesham wood post on four corner out of 75*75 mm size (seventy five into seventy five milimetre ) (decorative with bluster in between the post shell be made of shesham wood 40 mm ( Forty milimeters )diametre and to be fixed with decorative and rail of shesham having size of 75*65 mm ( seventy five into sixty five milimetres ) as per specification, approved design and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of Malkhana, Royality, Octroi, toll tax and any taxes imposed by the Government.

Providing and fixing 1620 ( One thousand six hundred twenty) 20mm OD ( Twenty Millimeter outer diamension) Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450 ,2004 for concealed work including cutting chases and making good the wall etcetera of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetera with clamps at 1.00 ( One) metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

Providing and fixing 2025 ( 25mm OD) Two thousand twenty five ( twenty five millimeter outer dimension) Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450 ,2004 for concealed work including cutting chases and making good the wall etcetera of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetera with clamps at 1.00 ( One) metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Making connection 25 to 40 mm (Twenty five to forty millimeter) nominal bore of G.I. distribution branch with G.I. main by providing and fixing tee, including cutting and threading the pipe etcetra complete as per direction of the Engineer-incharge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and Fixing high pressure P.V.C spigot and socket soil, waste and ventilating Pipe of Supreme/ Finolex/ Vectus/ Relpipe ( Reliance) prince ISI marked including fixing with approved adhesive etcetra complete as per the direction of Engineer-in-Charge including carriage of material with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

(i) 110mm dia ( One Hundred Ten Millimeter) diameter

(ii) 75mm dia ( Seventy Five Millimeter) diameter

Providing and fixing PVC. holder bat clamps of ISI marked of Sepreme, faince Finolex , Relpipe (Reliance ) , Vectus approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm (Ten isto Ten isto Ten centimeter) of 1:2:4 mix (One cement isto Two coarse sand isto Four graded stone aggregate 20 mm (Twenty millimeter) nominal size) and cost of cutting holes and making good the walls etcetra complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

(i) 110mm dia ( One Hundred Ten Millimeter) diameter

(ii) 75mm dia ( Seventy Five Millimeter) diameter

Providing and fixing P.V.C. ISI marked of Finolex , Supreme , Prince Relpipe (Reliance ) , Vectus heal rest Confirming to IS no-14735-99 including filling the joints with approved adhesive complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

(i) 110mm dia ( One Hundred Ten Millimeter) diameter

(ii) 75mm dia ( Seventy Five Millimeter) diameter

Providing and fixing P.V.C. collar marked of Finolex ,Supreme / Prince/ Relpipe (Reliance ) , Vectus ISI marked confirming to IS No-14735-99 including fixing with approved adhesive complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

(i) 110mm dia ( One Hundred Ten Millimeter) diameter

(ii) 75mm dia ( Seventy Five Millimeter) diameter

Providing and fixing P.V.C. cowl 75mm dia ( Seventy five Millimeter diameter) ISI marked of Finolex , Supreme/ Prince Relpipe (Reliance ) , Vectus ISI marked Confirming to IS No-14735-99 including fixing with approved adhesive complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 110 x 90 mm ( One Hundred Ten into Ninety Millimeter) nominal size/diameter P.V.C. floor trap ISI marked of Finolex , Relpipe (Reliance ) , Vectus, Supreme, Prince,conforming Confirming to BIS-14735-99 of self cleaning design including fixing with approved adhesive , cost of cutting and making good the wall and floor etcetera complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 110 x 75 mm ( One Hundred Ten into Seventy Five Millimeter) nominal size/diameter P.V.C. floor trap ISI marked of Finolex , Relpipe (Reliance ) , Vectus, Supreme, Prince Confirming to BIS-14735-99 of self cleaning design including fixing with approved adhesive , cost of cutting and making good the wall and floor etcetera complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

Providing and fixing white viterous china water closet squatting pan (Indian type W.C. pan ) Orissa pattern W.C. pan no 20090 of size 530x410 mm ( Five Hundred thirty into four hundred Ten Millimeter) with integral type foot rests with 100 mm ( One hundred millimeter) P.V.C P or S trap, 10 litre ( Ten Litre) low level P.V.C. flushing cistern having dual flush system of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet (European type)Star cube No 20092 (S - 10 ) Size 61.5 X 34.5 X 40 cm ( Sixty one point five into Thirty four point five into forty Centimeter) with ISI marked white plastic seat lid P.V.C 10( Ten) litre low level having dual flush and fixed with net pressure flushing cistern (sleek Plus) Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40 mm ( Forty Millimeter) flush bend, over flow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete as per the direction of Engineer-in-Charge with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet (European type)Star S No 20087 (S - 10 ) Size 57 X 35 X 39 cm ( Fifty Seven into Thirty Five into Thirty Nine Centimeter) ISI marked plastic with seat and lid, 10( Ten) litre low level P.V.C having dual flushing and fixed with Jet pressure flushing cistern (sleek Plus) Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40 mm ( Forty Millimeter) flush bend, over flow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete as per the direction of Engineer-in-Charge with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type Matrix water closet (European type) fixed with Jet pressure, ISImarked white solid plastic seat and lid, 10 (Ten) litre low level white flushing cistern having dual flush system of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40 mm( Forty Millimeter) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing white vitreous china range of three half stall urinal Large flat back 60002 of size 39 x 37.5 x 59 cm ( Thirty Nine into Thirty Seven point Fifty Nine Centimeter) with 10 ( ten) litre white PVC automatic flushing cistern of Hindware / Cera /Jaquar of star white / Snow white shade and as shown in the drawing / as per details with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST or any other taxes imposed by the Government.

Providing and fixing white vitreous china Division plate of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details urinal with integral rim longitudinal flush pipe complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing wash basin White Vitreous China Flat back wash basin Neptune no 10072 of size 55x 48x86cm (Fifty five isto forty eight isto eighty six centimeter) with pedestal of Cera / Hindware / Jaquar of s far white/ snow white shade with single 15 mm (Fifteen millimeter) diameter nominal bore C.P. brass pillar taps with C.I brackets 32 mm (Thirty two millimeter) diameter C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing wash basin White Vitreous China Flat back wash basin Garnet no 10080 of size 580x 430 mm ( Five hundred Eighty into Four hundred Thirty Millimeter) ( Under counter Basin ) of Hindware , Cera , Jaquar of star white / Snow white shade and as shown in the drawing / as per details with single 15 mm ( Fifteen Millimeter) diameter C.P. brass pillar tap with C.I. brackets 32 mm (Thirty Two Millimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing White Vitreous China Flat back Matrix wash basin 550x 400 mm Five Hundred fifty into Four hundred millimeter) of Cera / Hindware / Jaquar of star white /snow white in drawing as per detail with single 15 mm ( Fifteen Millimeter) diameter C.P. brass pillar tap with C.I. brackets, 32 mm (Thirty Two Millimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details for wash basin completely recessed at the back for the reception of pipes and fittings complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink of Diamond / Unik with drain board 510x1040 mm (Five hundred ten isto One thousand forty millimeter) bowl depth 250 mm ( Two Hundred Fifty Millimeter) with C.I. brackets and stainless steel plug 40 mm ( Forty Millimeter) including painting of fittings and brackets, cutting and making good the walls wherever required as approved by Engineer - in - charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 32 mm dia (Thirty two millimeter diameter) C.P. brass chain and rubber plug of ISI marked for sink or wash basin complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres M.I. union for wash basin or sink.complet as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 32 mm dia (Thirty two millimetres diametres) C.P. Brass waste of Continental series of Jaquar / contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal for wash basin and sinkn complete (New work) as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetres) diametres C.P. Grating for gully floor or nahni trap Continental series of Jaquar / contess plugs series of Hindware /ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 600x450 mm ( Six Hundred into Four hundred Fifty Millimeter) beveled edge mirror of Confinental series of Jaquar / contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal of superior glass (of approved quality) complete with 6 mm ( Six Millimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing C.P. brass towel rail 600X20 mm ( Six Hundred into Twenty Millimeter) of Continental series of Jaquar / contess plus series of Hindware/ Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jalcomplete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 600x120x5 mm ( Six Hundred into One Hundred Twenty into Five Millimeter) glass shelf of Continental series of Jaquar / Contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm ( Forty Millimeter) long screws, rawl plugs complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing C.P. brass toilet paper holder of Continental series of Jaquar / Contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 8 mm ( Eight Millimeter) dia C.P. / S.S. Jet of Continental series of Jaquar / Contess series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal with flexible tube upto 1 ( One) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15 mm ( Fifteen Millimeter ) Nominal bore C.P. brass bib cock tap of Continental series of Jaquar /Contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jalf approved quality conforming to IS:8931 complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15 mm ( Fifteen Millimeter ) nominal bore C.P. brass stop cock (concealed) Continental series of Jaquar /Contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal of standard design and of approved make conforming to IS:8931 complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15 mm (Fifteen millimeter) nominal bore C.P. brass pillar tab cock (concealed) of Continental series of Jaquar / Contess plus series of Hindware /Ocean series of Cera / Vintag series of Kerovite & Hindon series of Jal of standard design and of approved make conforming to IS:8931 complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15 mm ( Fifteen Millimeter ) nominal bore C.P. brass angle valve of Continental series of Jaquar / contess plus series of Hindware /Floral series of Cera / Vintage series of Kerovite & Hindon series of Jalfor basin mixer and geyser points of approved quality conforming to IS:8931 complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15 mm (Fifteen millimeter) nominal bore C.P. brass full way valve with wheel, of Continental series of Jaquar / contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimeter) nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of Continental series of Jaquar / contess plus series of Hindware /Ocean series of Cera / Vintage series of Kerovite & Hindon series of Jal complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal bore PVC connection with brass union 45cm ( forty five centimeter) length,of Finolex , Relpipe (Reliance ) , Vectus/Supreme/Prince complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 32 mm ( Thirty Two Millimeter) dia P.V.C.flexible waste pipe of Finolex , Relpipe (Reliance ) , Vectus /Supreme/Prince for sink or wash basin including P.V.C. waste fittings complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and placing on tarrace 1000 ltrs (One thousand literes) capacity PVC water storage tank (Sintex make 4 layers Supreme/finolex/prince of ISI-12701 marked GI inlet or and outlet connections 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC with locking arrangement including hoisting up to all heights above ground level as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 150mm (one hundred fifty millimetrse) nominal bore diameter to level or slopes P.V.C Severage pipe of (Finolex/Vectus/Relpipe Reliance /Supreme of working pressure not less than 4 to 6 kg (four to six kilogram) per square centimetres of high density pipe conforming of IS code 4985-200 including filling the joints with approved adhesive complete and as per the direction of Engineer-in-Charge including carriage of materials with in all leads and lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 {One cement isto Five coarse sand isto Ten graded stone aggregate 40 mm ( Forty Millimeter) nominal size}150 mm ( One Hundred Fifty Millimeter) diameter PVC Pipe complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 (One cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix {One cement isto One point five coarse sand (zone- III) isto Three graded stone aggregate 20 mm ( Twenty Millimeter) nominal size, foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm ( Forty Millimeter) nominal size), inside plastering 12 mm ( Twelve Millimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto four graded stone aggregate 20 mm ( Twenty Millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm ( Ninety into Eighty Centimeter) and 45 cm ( Forty Five Centimeter) deep including C.I. cover with frame (light duty) 455x610 mm ( Four Hundred Fifty Five into Six Hundred Ten Millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg ( Thirty Eight Kilogramme) {weight of cover 23 kg ( twenty Three Kilogramme and weight of frame 15 kg ( Fifteen Kilogramme} With Sewer bricks conforming to IS : 4885 complete as per the direction of Engineer-in-Charge icluding carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST nad any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 (One cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix {One cement isto One point five coarse sand (zone- III) isto Three graded stone aggregate 20 mm ( Twenty Millimeter) nominal size, foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm ( Forty Millimeter) nominal size), inside plastering 12 mm ( Twelve Millimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto four graded stone aggregate 20 mm ( Twenty Millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm ( Ninety into Eighty Centimeter) and 45 cm ( Forty Five Centimeter) deep including C.I. cover with frame (light duty) 455x610 mm ( Four Hundred Fifty Five into Six Hundred Ten Millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg ( Thirty Eight Kilogramme) {weight of cover 23 kg ( twenty Three Kilogramme and weight of frame 15 kg ( Fifteen Kilogramme} With Sewer bricks conforming to IS : 4885 complete as per the direction of Engineer-in-Charge icluding carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST nad any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 (One cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix {One cement isto One point five coarse sand (zone- III) isto Three graded stone aggregate 20 mm ( Twenty Millimeter) nominal size, foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm ( Forty Millimeter) nominal size), inside plastering 12 mm ( Twelve Millimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto four graded stone aggregate 20 mm ( Twenty Millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm ( Ninety into Eighty Centimeter) and 45 cm ( Forty Five Centimeter) deep including C.I. cover with frame (light duty) 455x610 mm ( Four Hundred Fifty Five into Six Hundred Ten Millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg ( Thirty Eight Kilogramme) {weight of cover 23 kg ( twenty Three Kilogramme and weight of frame 15 kg ( Fifteen Kilogramme} With Sewer bricks conforming to IS : 4885 complete as per the direction of Engineer-in-Charge icluding carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST nad any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 (One cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix {One cement isto One point five coarse sand (zone- III) isto Three graded stone aggregate 20 mm ( Twenty Millimeter) nominal size, foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm ( Forty Millimeter) nominal size), inside plastering 12 mm ( Twelve Millimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto four graded stone aggregate 20 mm ( Twenty Millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm ( Ninety into Eighty Centimeter) and 45 cm ( Forty Five Centimeter) deep including C.I. cover with frame (light duty) 455x610 mm ( Four Hundred Fifty Five into Six Hundred Ten Millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg ( Thirty Eight Kilogramme) {weight of cover 23 kg ( twenty Three Kilogramme and weight of frame 15 kg ( Fifteen Kilogramme} With Sewer bricks conforming to IS : 4885 complete as per the direction of Engineer-in-Charge icluding carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST nad any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 (One cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix {One cement isto One point five coarse sand (zone- III) isto Three graded stone aggregate 20 mm ( Twenty Millimeter) nominal size, foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm ( Forty Millimeter) nominal size), inside plastering 12 mm ( Twelve Millimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto four graded stone aggregate 20 mm ( Twenty Millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm ( Ninety into Eighty Centimeter) and 45 cm ( Forty Five Centimeter) deep including C.I. cover with frame (light duty) 455x610 mm ( Four Hundred Fifty Five into Six Hundred Ten Millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg ( Thirty Eight Kilogramme) {weight of cover 23 kg ( twenty Three Kilogramme and weight of frame 15 kg ( Fifteen Kilogramme} With Sewer bricks conforming to IS : 4885 complete as per the direction of Engineer-in-Charge icluding carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST nad any other taxes imposed by the Government.

Providing and laying (to level or slope) 110mm ( One hundred ten Millimeter) PVC (D-Plast) sewer pipe of working pressure not less than 4.5 K.G/Sqm (Four point five kilograme per square meter) including filling the joints with approved adhesive complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and Fixing 1.00 HP ( One horse power) water lifting pump ISI marked of Kirloskar/Cromption including accessories and making necessary connection as required at site for its functioning complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

Providing and fixing 15 mm (fifteen millimeter) nominal bore mild steel tube including fitting complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads , lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, sales tax,GST and any other taxes imposed by the Government.

suresh kumar gupta

M/S BALDEV KUMAR GOVT. CONTRACTOR

Naresh Padiyal