Construction of SC with prefabricated steel structure, brick work in foundation 112mm thick brick walling at various places of Assam under NHM, pkg.NSC G3 (Balance work of 5 nos. of SC in Goalpara District)

Amount

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in substructure upto plinth level ( in prop. 1:4 )(a) In proportion 1:3

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in substructure upto plinth level ( in prop. 1:4 )(b) In proportion 1:4

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (a). In cement mortar in proportion 1:4.(1 cement:4 sand)(a) In cement morter in proportion 1:4(1 cement :4 sand)

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). b) TMT Bar (I) TATA/ SAIL ISI approved super ductile TMT Bar(ii)Other ISI marked

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). ISI approved -M.S Rod

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and proping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for in-situ reinforced concrete and plain concrete work.Foundation,footings,bases of columns,pile cap, raft and mass concrete work etc.Using 25 mm think plank

Sides of tie beams, grade beams etc. at or below ground level.Using 25mm thick plank

Columns, Pillars, Posts & StrutSquare, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face Using 25mm thick plank

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties For depth not exceeding 1.0M. Using 25 mm think plank

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like Floors etc. upto 200mm in thicknessUsing 25 mm think plank

Providing and laying plain/reinforced cement concrete works cement with coarse sand &20 mm down graded stone aggregate including dewatering if necessary and curing complete but excluding cost form work and reinforcement RCC work (Form work reifocement will be measured and paid saeparately) Using mixer machine In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M 15 or Prop. 1:2:4

In super structure from plinth level up to 1st floor level Coloumns, pillars,posts,struts,suspended floor,roof,landing,shelf and support,balcony,lintel,sill band,beam,girder,bressumer,cantilever,staircase(except spiral staircase and landing) including preparing the top surface and finishing the nosing. M 15 or Prop. 1:2:4

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC bl side hung and top hung windows and ventilators 5mm clear glass

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rub (b) 3 Track sliding window (ii)5 mm frosted glass

Providing, fitting and fixing coloured anodised aluminium framed double leaf glazed doors with anodised aluminium frame made of 100mm x 45mm x 2mm sections with door styles of size 81mm x 45mm x 2mm, top rails 50mm x 45mm x 2mm, lock rails 81 mm x 45mm x 2mm,bottom rails 100mm x 45mm x 2mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the Department at all levels. (ii)5 mm frosted glass

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. (ii) 35 mm thinck

Providing, fitting and fixing 40mm x 48mm wood reinforced PVC chowkhats fixed to the columns / stiffeners / walls with necessary holdfast / sleeves etc. as specified and directed at all levels.

Providing, fitting and fixing 24mm/ 29mm thick polymer reinforced moulded PVC door shutters fixed to the chowkath with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately.) 24 mm think

15 mm thick Cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. (b) In cement mortar 1:4

15 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed (b) In cement mortar 1:4

Providing barge board of size 200mm x 20mm with 1st class local Hollock/ Bonsum timber including fitting and fixing with necessary wood screws etc. complete.

Providing fitting, hoisting and fixing of roof trusses including purlins fabricated out of M.S. black-tubes conforming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed.

Providing corrugated galvenised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvenised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc. (Roof trusses and purlin etc.to be measured and paid separately). b) 0.50 mm thick

Providing galvenised iron ridging of TATA SHAKTEE / SAIL including supplying and fixing necessary galvd screws/washers etc. complete as directed. b) 0.50 mm thick ii) 230 mm lapping

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed.a) M .S. angle

20 mm thick Cement plaster in two coats, backing coat 15 mm and finishing coat 5mm thick on rough side of single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. a) in cement mortar 1:3

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc. complete as directed.

Providing wood work in frame (chowk aths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (b). With 1st class timber (Hollock/ Sundi)

Providing wood work in frame of false ceiling partitions etc.sawn, wrought, framed hoisted and fixed in positon with spikes, nails, M.S flat,angle/ cleats with bolt and nuts complete including kiricide oiling two coats to unexposed surfaces of the timber (M.S flats, angle cleats, and bolt and nuts required for flat, angle cleats wherever necessary shall be measured and paid separately). (b) With Holliock/ Bonsum /Sundi

Providing, fitting and fixing in position plywood / hardboard partion walls with 6mm thick plyboard / hardboard (best) with horizontal an d vertical Sal battens of size 50mm x 80mm spaced at not more than 1.20m apart with necessary nails,wood screws, bolts etc. complete as directed by the Department for all levels (Painting / Varnishing to be measured and paid separately). B) 6 mmthink Hardboard a) On one face of the frame

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). a) Normal range (sizes 300mmx300mm and above) d) Asian made

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). a) Normal range (sizes 300mmx300mm and above) a) Orient made

Providing Anti-skid tiles of approved quality size ,shape not less than 8mm on floor skirting over a cement mortar……etc b) Executive range

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. b) 20 mm think

Providing, fitting and fixing M.S. grill of requiredpattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws.I. Plain grill c) Fixed to brickwork/P.C.C/R.C.C

Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i) 300 mm wide and average 150 mm deep with bed slope 1in 150 with initial depth of 100mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) a) Sliding door bolts ii) 250mm x 16mm

b) Tower bolts ii) 250mm x 12mm

m) Distempering two coats with oil bound distemper of approved brand and manufacture and of required shade on new wall surface to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after throughly brooming the surface free from mortar dropings and other foreign matter and including preparing surface even and sand papered smooth. (i).Priming coat with distemper primer

(ii). Top coat

Finishing old/ new wall with water proofing weather coat smooth anti-fungal exterior painting of Apex brand of Asian Paints and of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (b). With ready mixed paint , wood primer (white).

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. (i).Surfaces over 100mm in width or girth. b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc. complete at all levels including below G.L. as directed and specified. I) Exposed or in trenches d)25 mm dia i)Using Tata (mediam)

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc. complete at all levels including below G.L. as directed and specifiedii) using ITC/ Nozone (medium)

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc. complete at all levels including below G.L. as directed and specified. I) Exposed or in trenches d)25 mm dia i)Using Tata (mediam) f) 15 mm dai i)Using Tata (mediam)

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc. complete at all levels including below G.L. as directed and specified. I) Exposed or in trenches d)25 mm dia i)Using Tata (mediam) ii) using ITC/ Nozone (medium)

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified (G.I. & C.P. pipes will be measured separately) A) Essco make (Delux/Sumthing spl./Tropical) a) Bid Cock Short Body

Sona brand ii) Bid Cock long Body Code no CL-1031 Supplying and fitting fixing C.P. pillar cock of 15 mm dai of appooved drend as specefy and directed Sona brand Light tipe

Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) Sona make a) stop cock male/ female 15 mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii)110 mm dia

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. ii)110 mm dia

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. iv) 75 mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. ii)110 mm dia

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. ii)110 mm dia

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. iv) 110 mmx75 mm dia

Providing fitting and fixing 75mm dia. PVC cowel of ISI make complete as directed and specified.

Providing fitting and fixing white vitreous china pedestal type water closet (European type W.C pan 400mm high ) of Parryware/Hindware make with seat and lead ,CP brass hinges and rubber buffers ,10 litre low level PVC flushing cistern with fittings, CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. a) White

Providing vitreous China wash basin of size 630mm x450mm of Parryware make with CI/MS brackets, 32mm CP brass waste coupling of standard pattern,C.P stop cock,C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required.a) White vitreous china wash basin of size 630mm x450mm

Providing, fitting and fixing chrome plated (CP) towel rail of Jaquar make complete as specified and directed. (c) Queen's Accessories (450mm long)

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes iii) 1000 litre capacity a) Sintex make

Wiring for light point with PVC 1.5 sq. mm insulated unshealthed 1.1KV grade as approved by the deptt .single core copper conductor ISI marked cable) in Recessed PVC casing conduit wiring system incliding 6 Amps flush type switch (ISI marked) ceiling rose complete(b) Medium point up to 6.00 meter length

Wiring for light point with PVC 1.5 sq. mm insulated unshealthed 1.1KV grade as approved by the deptt .single core copper conductor ISI marked cable) in Recessed PVC casing conduit wiring system incliding 6 Amps flush type switch (ISI marked) ceiling rose complete(c) Long point up to 10.00 meter length

Wirring as of item no 43 above the surface pvc condute wirring system with 19 mm dia rigid pvc casing caping condute to (b) Medium point up to 6.00 meter length

Wirring as of item no 43 above the surface pvc condute wirring system with 19 mm dia rigid pvc casing caping condute to (c) Long point up to 10.00 meter length

Wiring to 5 pin 6 Amps plug point including providing fixing 5 pin 6 Amps flush type outlet ,6 Amp flush type switch (ISI) marked .wiring as of item no. 47 to a 5 pin 6 Amps plug point when fixed same boared.

Wirring as of item no 43 above call bell point in surfece pvc casing caping condute wirring system with 19 mm dia rigid pvc casing caping condute pipes (c) Long point up to 10.00 meter length

Wiring for drawing sub main with PVC insulated unhealthy ISI marked single ore copper conductor cable in Recessed PVC conduit wring system including earth continuity cable with PC insulated unsheathed copper single core conductor painting etc. a) with 2 x2.5 sq mm + 2.5 mm pvc insulated unsheathed single core copper conductor cable with 19 mm dia rigid pvc casing capping conduits

Wiring for drawing sub main with PVC insulated unhealthy ISI marked single ore copper conductor cable in Recessed PVC conduit wring system including earth continuity cable with PC insulated unsheathed copper single core conductor painting etc. b) with 2 x2.5 sq mm + 2.5 mm pvc insulated unsheathed single core copper conductor cable with 19 mm dia rigid pvc casing capping conduits

Wiring for drawing sub main with PVC insulated unhealthy ISI marked single ore copper conductor cable in Recessed PVC conduit wring system including earth continuity cable with PC insulated unsheathed copper single core conductor painting etc. c) with 2 x2.5 sq mm + 2.5 mm pvc insulated unsheathed single core copper conductor cable with 25 mm dia rigid pvc casing capping conduits

Supplying including fitting fixing of high speed AC ceiling fan complete with all accessories regulator,down rod, canopy etc. of following sweeps and making necessary connections etc, as required complete.and directed by the deptt. a) 1400 mm sweep

(a)Installation of earth station with 40mm dia and 4.50m long G.I pipe with necessary G.I reducing socket 40mmx 20mm size locking arrangement with hinged cover plate,funnel,G.I nuts,through bolts etc. for putting pipe and refilling with necessary enclosure on the top etc as required complete.

(b) Extra for using salt(5Kg) & charcoal(64 Kg for pipe earth electrode etc. as required)

Proiding and fixing 8 S.W.G GI earthware in surface or in recesses for roof earthing as required complete.

Supplying, Installation,testing & commissioning of the following CFL/Fluorescent luminaires complete with all accessories such as ballast, starter etc. on the ceililng /wall including with connection with 1.5 Sq.mm P.V.C insulated single (d) box type HPF luminaires complete copper ballst 1x40w f tube..

Supplying , fitting and fixing of single pole 10 KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connection as specified & directed bt the deptt.

Supply and laying of following size of PVC/XLPE insulated and PVC sheathed 1.1 KV grade aluminium conductor LT armoured UG cable laid in ground/partially in air (10% of cable length) including excavation of cable trench upto depth of 75cm. Refilling, protective covering sand cushioning complete handling of surplus soil debris etc. to proper place as specified and directed by deptt. © 25,00 mm2 core U.G cable

Supplying including fitting fixing of high speed AC ceiling fan complete with all accessories regulator,down rod, canopy etc. of following sweeps and making necessary connections etc, as required complete and directed by the deptt.. a) 1400 mm sweep

Supplying and fixing fancy wall bracket of Anodized aluminum 12mm.Dia Fixed on 3 mm .Thick 170mmx40mm. M.S. plate with brass bracket lamp holder including shade etc. and connection complete (without bulbe)

Supplying and fixing of Call bell (Buzzer)including 5 Amps capacity button & piano type bell push switch including connection etc as required.

(a)Supplying & laying 8 SWG GI Earth wire drawn in 15mm Dia GI pipe from earth electrode including excavation work refilling connection etc. complete.

Supplying with fitting and fixing sheet steel, phophotised, powder painted Double Door surface mounted SPN MCB DB incorporated with bus-bar, neutral link, earth bar and Din rail etc. fitted on wall with grouting nuts and bolts as reqd. complete with making necessary connection as specified and directed by the deptt.(b) 8 way SPN double door

SAFIKUL ISLAM