REPAIR AND CLEANING OF SEWAGE LINE MANHOLE SEPTIC TANK ETC AND WELCOME MAINTENANCE TO MD OFFRS ACCN AT MIL STN DHRANGADHRA

Amount

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm with excavated soil complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2, using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

M&L for cement concrete (1:3:6), type C-1, using 20mm graded stone aggregate in coping and the like including weathering, slightly rounded or chamfered angles and throating, Including necessary form work complete all as specified and directed.

M&L pre-cast reinforced cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate for manhole covers including placing the cover in position and set in cement mortar (1:6) complete all as specified and directed. Note: Reinforcement shall be measured and paid seperately.

M&L for providing precast cement concrete type B1 1:2:4 (20mm graded aggregate) in landings, cover slabs(for manholes etc) with plain fair faces, including chamfers, weathering, throating etc and setting in cement mortar 1:6 complete with joints to match complete all as specified and directed.

M&L for cement concrete 1:2:4 Type B1 using 20mm graded stone aggregate as in fins, facia, chajja, parapet, louvers, railing complete to match with existing all as specified and directed.

Supply only, integral water proofing compound complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) completed as specified and directed.

M&L for walling of random rubble stone masonry, brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto course with maximum depression on face from straight edge held against the dressed surface not.exc. 20mm for sand stone complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F, factory made, 30mm thick, flush shutters, solid core construction, with block board core and plywood face panles, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5sq.m each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and directed.

Taking down steel window/ventilator including grills of any description, n. exc 1.5 Sqm each complete all as specified and directed

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish or electrogalvanised, width of flap 40 mm complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, butt hinges of 100mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F, 125 mm size, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F, mortice lock of mild steel, vertical type of size 75mm with duplicate key for door complete all as specified and directed.

S&F hasp & staples 125mm in size, safety type alu. anodised fixed with screws complete all as specified and directed.

S&F, in repairs, brass chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange complete all as specified and directed.

Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed.

S&F, in repairs, 20mm dia,stainless steel, fancy type, tubular curtain rod fix on decorative brackets with decorative globe at both ends complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, in repair, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars in gates etc and similar work conforming to Fe-290 (Gde-E-165) complete all as specified and directed

S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, inclding cranking, bendiing spirally for hooping for columns, hooking ends and biinding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F, Aluminium anodised sections for doors/windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- Floor door spring, sheet glass, wire cloth, lock, etc shall be measured and paid seperately.

S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and directed.

S&F mild steel rolled section Fe-410-W(Gde E-250), quality 'A' as in post, main and cross beams, rafters, purlins connected to common rafters fixed with angle iron clips or other connecting plates complete all as specified and directed.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F factory made steel ventilators with top hung shutter including hinges, steel peg stay, glazing bars including applying one shop coat of red oxide primer all as specified and directed

S&F, in repairs, false ceiling at any height, 600x600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH-99 classic lite' with suspension system complete all as specified as per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

S&F in repairs, 0.63mm thick, stainless steel plate rack of size 120cm x 90cm x 18cm complete all as specified and directed.

S&F, in repairs, 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber frame work in cup boards, rebated or flat edged complete all as specified and directed.

M&L for 6mm thick external teak wood lipping fixed to18/19mm thick block or Veneered particle boards with nails complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size350x250x7mm/450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 450 x 350 x 7mm thick High lighter tiles on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1;4 complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub base and finished the surface rough to receive tile complete all as specified and directed.

M&L for coloured non skid ceramic tiles, 7 to 8 mm thick, (square/rectangular), area of each tile exceeding 0.11 sq.m but not exceeding 0.18 sq.m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed

M&L coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but including 600 x 600mm size in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but including 600 x 600mm size as in dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for heavy duty, exterior grade ceramic tiles (Durastone of Somany/Endura of Johnson or equivalent as approved by GE) of size 300 x300x 10mm thick, set, jointed and pointed in neat cement slurry in trades/risers, landing with white cement and pigment over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed.

M&L for chequered cement concrete tiles 30cmx30cmx25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in cm (1:6) complete all as specified.

Dismantling stone slab and tiles of any description or thickness in floors,aprons etc. complete all as specified and directed.

M&L for 18-20mm thick black granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed.

M&L for rounding to edges of stone slabs two edge full round,such as in steps,cooking platform and other similar situation complete all as specified and directed.

M&L for 25mm thick cement concrete type B1, 1:2:4 (20mm graded stone aggregate) to receive floor finishes complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:4 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 15mm thick in cement mortar (1:4) on brick work or concrete surfaces using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, finished even and smooth without using extra cement complete all as specified and directed. Note:- Supply only water proofing compound shall be measured and paid separately.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for preparing new plastered or un-plastered walls surfaces and applying three coats white wash complete all as specified and directed.

M&L for preparation of new plastered or un-plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of cement base paint complete all as specified and directed.

M&L for preparing old plastered or un-plastered walls surfaces and applying one coats of white wash on walls complete all as specified and directed.

M&L for preparing of old plastered or un-plastered wall surfaces and applying one coat of oil bound distemper complete all as specified and directed.

M&L for preparing new plastered or un-plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment with Mechanical Scrubber on old plastered or un-plastered surfaces of walls and applying two coats of oil bond distemper over two coats Birla/JK white putty on walls complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surfaces of wall including brooming dowon or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of exterior paint over one coat of primer complete all as specified and directed. Make : Apex of Asian Paints or equivalent.

M&L for complete removal of existing treatment with Mechanical Scrubber on old plastered or un-plastered surfaces of walls and applying two coats of exterior paint over one coat of primer complete all as specified and directed.Make : Apex of Asian Paints or equivalent.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including chalk whiting on plastered surfaces, preparatory to distempering complete all as specified and directed.

Supply only oil bound distemper any tint any shade complete all as specified and directed.

Supply only cement base paint any tint any shade complete all as specified and directed.

Supply only chalk whiting any tint any shade complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) n.exc. 0.5 sq.m from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, pin headed type and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

S&F 4mm thick Sheet glass, ordinary quality with and including neoprene beadings in square nexc 0.5 sq.m in each pane complete all as specified and directed.

S&F, in repair, glass shelf, 600mm long complete all as specified and directed. Make-Jaquar Cat No ACN-1171N or equivalent as approved by GE.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over existing shop coat of primer complete all as specified and directed.

Supply only exterior emulsion paint complete all as specified and directed.

Supply only synthetic enamel paint superior tint complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of capacity 500 Litres (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR-Part-I including disconnecting and removal of old U/S PVC tank complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of capacity 1000 Litres (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR-Part-I including disconnecting and removal of old U/S PVC tank complete all as specified and directed.

S&F, in repair, pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, in repairs, 15mm brass chromium plated fancy type bib cock with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Supply only 15mm pillar taps, brass chromium plated fancy type with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe or for union and fixed to 15mm bore pipe, complete all as specified and directed.

S&F in repairs 32mm waste fittings brass chromi-um plated for glazed ware basin etc with long screwed shanks and fly nuts flange end complete ISI marked complete all as specified and directed.

S&F, in repairs, 15mm stop valves, fancy type brass chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, complete all as specified and directed.

S&F in repairs 25mm bore dia of gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F, in repairs, stop valves angular, chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, complete all as specified and directed as per Cat No MQT-513A of Essco or equivalent make approved by GE.

S&F in repair wash basin mixer tap with hot and cold fancy type all as per approved sample Make Jaquar or equivalent as approved by GE.

S&F, in repair, chromium plated, Toilet paper holder complete all as specified and directed. Make-Jaquar (Cat No - ACN -1153N) or equivalent as approved by GE.

S&F, in repair, 8mm dia brass, chromium plated health faucet (Hand shower) with 01 meter long flexible tube and wall hook complete all as specified and directed. Make : Jaquar Cat No - ALD-573 or equivalent as approved by GE, complete all as specified and directed.

S&F, in repair, brass, chromium plated, soap dish complete all as specified and directed. Make - Jaquar or equivalent as approved by GE

S&F, in repair, PTMT, Grating, 150mm size(minimum wt 100gms) with hole for waste pipe fixed with cement mortar complete all as specified and directed.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/ walls complete all as specified and directed.

S&F 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/walls complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval and access door of 75mm dia complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval and access door of 110mm dia complete all as specified and directed.

S&F PVC (SWR) branch piece single (single ‘Y’) equal or unequal suitable for 75mm bore pipe complete all as specified and directed.

S&F PVC (SWR) branch piece single (single ‘Y’) equal or unequal suitable for 110mm bore pipe complete all as specified and directed.

S&F, 75mm bore PVC (SWR) branch piece, single (Single Y) equal or unequal with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) branch piece, single(Single Y) equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) branch piece single (double ‘Y’) equal or unequal suitable for 110mm bore pipe.

S&F PVC (SWR) vent cowl of 75mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl of 110mm dia complete all as specified and directed.

S&F PVC (SWR) Floor/ Nahani trap with grating of diameter of outlet 75mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete fixed all as specified.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 200mm bore of pipe complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 300mm bore of pipe complete all as specified and directed.

M&L for salt glazed stoneware drain pipes, 150mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

M&L for salt glazed stoneware drain pipes, 200mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

M&L for 300mm bore reinforced concrete pipe class NP2 laid and jointed complete with collars all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete (1:2:4) type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 150mm bore of pipe complete all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete (1:2:4) type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 200mm bore of pipe complete all as specified and directed.

S&F,in repairs, chromium plated over head shower 100mm dia round shape single flow (ABS Body chrome plated with Gray face plate) with rubit cleaning system complete all as specified and directed as per Cat No EOS-542N of Essco or equivalent make approved by GE.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repair kitchen sink with drainage board made of stainless steel 1mm thick including supply and fix 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x4mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs white glazed earthen ware vitreous china wash hand basin of size 550x400mm with and including CI brackets, 32mm bore brass CP waste coupling Inlet/ outlet, PVC flexible pipe, 600mm size for 15 mm bore pipe with brass nut and washers etc complete.

Supply only PVC waste pipe 32mm bore of size 900mm to 1200mm long complete all as specified and directed.

De-silting/De-sludging the manholes/septic tanks not exc. 1.5m deep and getting out, removing & disposing off complete all as specified and directed.

De-silting/De-sludging the manholes/septic tanks depth exceeding 1.5m and n.exc. 3.0m and getting out, removing & disposing off complete all as specified and directed.

De-silting/De-sludging the manholes/septic tanks depth exceeding 3.0m and n.exc 4.5m and getting out, removing & disposing off complete all as specified and directed.

De-silting/De-sludging the manholes/septic tanks depth exceeding 4.5m and n.exc 6.0m and getting out, removing & disposing off complete all as specified and directed.

De-silting/De-sludging the gully traps and getting out, removing & disposing off complete all as specified and directed.

Removal of blockage/chock up obstructing the flow in sewage line by rodding with rods/wooden kempti/chock remover and making the continuous flow between two manholes for 150mm bore of pipe complete all as specified and directed. Note : The clear distance between two manholes shall be measured.

Removal of blockage/chock up obstructing the flow in sewage line by rodding with rods/wooden kempti/chock remover and making the continuous flow between two manholes for 200mm bore of pipe complete all as specified and directed. Note : The clear distance between two manholes shall be measured.

Removal of blockage/chock up obstructing the flow in sewage line by rodding with rods/wooden kempti/chock remover and making the continuous flow between two manholes for 300mm bore of pipe complete all as specified and directed. Note : The clear distance between two manholes shall be measured.

S&F, in repair, plastic water closet seat white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, such as manholes cover etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings complete all as specified and directed.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes jointed in neat cement mortar and taking out of trenches if required complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed stoneware, AC or RCC) set in cement mortar for 150mm bore of pipe complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed stoneware, AC or RCC) set in cement mortar for 200mm bore of pipe complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed stoneware, AC or RCC) set in cement mortar for 300mm bore of pipe complete all as specified and directed.

Navkar Enterprises

Priya Construction co.

Agarwal and Company

divyarsh entrprise

Shree Builders

ALBA AC AND REF SERVICES

Marudhar construction company

GIRNAR CONSTRUCTION