Renovation and repairing work of Toilet block near vigyan bhavan at Science City, Abad

Item of work Unit Quantity Rate Amount

Dismantling santtary fittings like wash basin . W.C.

pan Indian and European type, flushing tank etc.

including stacking the materials with all lead and

lift. . (R&B SOR Item no.20016)

Dismentling doors, windows, ventilators etc. (wood

or steel) shutters including chowkhats architraves,

holdfasts and other attachment etc. complete and

stacking them within all lead and lift.(i) Not

exceeding 3 Sq.M. in area. (R&B SOR Item no.

Dismentaling tiled of stone floors laid in mortar

including stacking of serviceable materilas and

disposalofunserviceablematerialswith allleadand

lift.(R&B SOR Item no. 20005)

Demolition including stacking of serviceable

materilas and disposal of unserviceable materials

with all lead and lift. (i) R.C.C. work (R&B SOR

Item no. 20002)

Dismantling Cement Asbestos Hard Board In

Ceiling Or Partition Walls, Wooden Trellies Work

5 Including Trellies Work Including Frames, Stacking Smt 217.88 29.00

Of Serviceable Materials And Disposal Of

Unserviceable Material With All Lead And Lift. MR

Excavation for foundation upto 1.5 m depth

including sorting out and stacking of useful

6 materials and disposing off the excavated stuff cmt 10.00 201.81

upto 50 Meter lead.(A) Loose or soft soil (R&B

SOR Item no.04B001A)

Providing and fixing Conventional EWC (Wall

hung) Cera or equivalent with close seat cover

including Jaquar or equivalent Hand Shower

(Health Faucet) with 8mm Dia, 1 Meter Long

Flexible Tube,flush pipe & Wall Hook with all fitting

inlet and outlet connection and all required fitting

accessories etc. completed as per directed

engineer in-charge. RA

Providing and fixing Indian-type water closet

(squatting pan) of Cable Orissa Pan (BR) Cera or

equivalent including 100 mm size P-trap or S-trap,

and jointing the trap with the pan and soil pipe with

cement mortar 1:1 (1 cement : 1 fine sand), with all

fitting inlet and outlet connection and all required

fitting accessories etc. completed as per directed

engineer in-charge .RA

Providing and fixing Urinal of CERA or equivalent

including connection with trap ,CERA Cera

Auxiliaries - F8050101Â or equivalent Waste

coupling full thread ,flexible PVC outlay pipe and

with integral longitudinal flush pipe etc completed.

Providing & Fixing Counter Table top Wash Basin

CATMAX Cat No. :S2020159 or equivalent on

platform of 600 mm wide Wash Basin size 650 x

380 x 110 mm including waste brass coupling,

stainless steel extension nipple, flexible PVC outlay

pipe, Casted Swinging Spout jaguar etc complete

as suggested by Architect/Engineer-in-charge. RA

Providing and fixing Bib Cock with wall flang and

aerator cock Cera or equivalent Cat.No. F2002151

11 or equivalent including all Fittings and labour No. 23.00 890.10

charges etc. Completed as per directed engineer

Providing and fixing Angle stop cock JAQUAR

brand FLORENTINE CAT. NO. - 5053N or

equivalent with 15 mm dia with C.P. brass

extension nipple 62 mm long etc. complete. RA

Providing and fixing Cera Pillar Cock Cat No.

F9030451 or equivalent with 15 mm dia with C.P.

brass extension nipple 62 mm long etc. complete.

Providing and fixing S.S. Cup Type Nahni Trap of

Standard quality or it's equivalent including cutting

hole and self clean design itc completed as

Providing and fixing S.W. gully trap with C.I. grating

brick masonry chamber and water tight C.I. cover

with frame of 300mm x 300mm size (inside) with

standard weight.(i) Square mouth traps.(B) 150mm

x 100mm size P or R type (R&B SOR Item

Providing and fixing Jaguar FLV-1089G or

equivalent Metropole Flush Valve Dual Flow

16 mm Size ( Concealed Body) with with with No. 26.00 3363.80

Exposed Shut Off Provision including all accassary

and fitting charges etc. complete. RA

Providing and fixing Jaquar FLV-1089G or

equivalent Metropole Flush Valve Dual Flow

17 50mm Size ( Concealed Body) with Exposed Shut No. 16.00 4628.80

Off Provision including all accassary and fitting

charges etc. complete. RA

Providing & Fixing in position standard extruded

approved colour anodised Aluminum Ventilator

with Jindal sectiom 14053 @ wt. 0.738 kg/rmt with

5mm x 100mm fixed frosted with glass blade

louvers with finishing joints with silicon sealant

including Exhaust Fan fix and tures, fastenning,

labours and equipments as per detailed drawing

as directed. For Ventilators. RA

Providing and laying 18 mm thick polished Black

or colour Granite stone slab machine cut in single

piece with all exposed edges polished, chamfered

and proected 6mm from finished wall thickness in

sill and jambs laid on 10 mm thick cement mortar

: 3 ( 1 cement : 3 coarse sand ) laid over and

19 jointed withgrey cement slurry including rubbing Smt 45.44 2376.30

and polishing etc. complete. also Fixing: Rear face

of granite shall be standed using clean sand sieve

no. 10 passed 2mm fixed with araldite and dried for

at list 36 hours. RA

Providing and laying Vitrified tiles 8 to 10 mm thick

, 24'' x 24'' in skrting risers of steps and dedo on

20 10mm thick cement plaster 1:3 (1-cement : Smt 400.00 1130.15

3coarse sand) and jointed with white cement slurry

(R&B SOR Item no. 14009CA)

P&L24"x 24"vitrified 8mm thicktileflooring over

mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with

color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for

antiskit (R&B SOR Item no. 14021A)

Wall painting (two coats) with plastic emulsion

paint of approved brand and manufacture on new

wall surface to give an even shade including two

coats of putty & two coats of primer of approved

22 brand including thoroughly brushing the surface Smt 142.19 118.63

free from mortar dropping and other foreign matter

and sand papered smooth for all floors as directed

by Architect. (R&B SOR Item no. 18031 + 19032)

Painting (two coats) with plastic emulsion paint of

approved brand and manufacture on Celing and

sloping surface to give an even shade including

two coats of putty & two coats of primer of

23 approved brand including thoroughly brushing the Smt 301.94 123.99

surface free from mortar dropping and other foreign

matter and sand papered smooth for all floors as

directed by Architect. (R&B SOR Item

Finishing wall with 100% acrylic emulsion

wetherproof paint on wall surface to give an

required shape even shade after thoroughly

24 brushing the surface to remove all dirt, and Smt 530.27 113.40

remains of loose powdered materials.etc complete

for any height as directed by Architect.(R&B SOR

Providing laying and jointing in true line and level

15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In

Charge. Pipe shall befixed on the wall with the help

25 of clamp at every two metre C/C or shall be Rmt 220.00 71.93

concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing

the same with adhesivesolvent, includingcost ofall

materials.(R&B SOR Item no. 23061)

Providing laying and jointing in true line and level

25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In

Charge. Pipe shall befixed on the wall with the help

26 of clamp at every two metre C/C or shall be Rmt 140.00 90.93

concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing

the same with adhesivesolvent, includingcost ofall

materials. (R&B SOR Item no. 23062)

Providing laying and jointing in true line and level

50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In

Charge. Pipeshallbefixed on the wallwith the help

27 of clamp at every two metre C/C or shall be Rmt 200.00 193.73

concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing

thesame with adhesivesolvent,includingcost of all

materials. (R&B SOR Item no.23065)

Providing and fixing to wall ceiling and floor

Kg. F/Cm2 working pressure polythene pipes of the

following outside Dia. Low densidy, complete with

special falnge compression type fittings, wall

clipsetc. including making good the wall ceiling and

floor.(E) 50mm (R&B SOR Item no.23004E)

Providing, laying and jointing in true line and level

110 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to

ISI 14735-1999 of approved make for drainage

system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on

29 wall using of PVC clamp of the size 110 mm Rmt 140.00 826.88

diametre x 149 mm length x 145 mm heigh at

every 2000 mm center to center or shall be

concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing

of pipes and joints and jointed with adhesive

solvent cement including cost of all materials. (R&B

SOR Item no.23067)

Providing Erecting and fixing Triple Layer Plastic

Pure Antibacterial Water White Tank of required

30 capacity each with all necessary fittings and Ltr 8000.00 9.80

connection etc. complete on terrace. RA

Providing and fixing full height Prelam PVC

partition system 50mm thick consisting of 40mm

sandwich PVC panel made out of 36mm high

density expanded polystyrene sheet (E.P.S.

Thermocol) stuck on both side with 2mm thick

prelimPvC sheet reinforced with frame work made

from 35mm x 5mm M.S. angle. In between two

M.S. angles 4 mm with feathered edges shall be

fixed on floor and 50 x 75 mm with feathered edges

prelim PVC “C” channelofsize50mmx75mmwith

featherededges prelim PVC panel shall be inserted

31 in the PVC ‘C” channel The first and last M.S. Smt 118.58 2152.00

angle should be erected such that it is inside a

PVC C channel of size 50 x 75mm In between

adjoining EPS sandwiched PVC partition panel

4mm thick x 75 mm width prelim PVC sheet

feathered at edges shall be stuck on front and

backfaceusing solvent cement etc.An additional

4mm thick PVC strip of 40mm width is to be stuck

on the intrior side of the ‘C” channel using PVC

solvent adhesive completeas per direction of

Engineer in charge. Manufacture’s specification

and drawing. (R&B SOR Item no.10055)

Providing and fixing 30mm thick FACTORY MADE

SOLID BOTH SIDE PRELAM PANEL PVC DOOR

SHUTTER consisting of frame made out of M.S.

tubes of 19 gauge thickness and size of 19mm x

19mm for stiles, top and bottom rails. M.S. frame

shallhaveacoat ofsteel primerof approved makde

and manufactures. M.S frame covered with 5mm

thick heat moulded prelim PVC ‘C’ channel of siz

30mmthickness,70 mmwidth ofwhich 50mmshall

be flat and 20mm shall be tapered in 45 degree

Angle on either side forming stiles, and 5mm thick,

95mm wide pream PVC sheet out of which 75mm

shall be flat and 20mm shall be tapered in

32 degree on the inner side ot form top and bottom rail Smt 36.96 2214.00

and 115mm wide prelim PVc sheet out of which

75nmm shall be flat and 20mm shall tapered on

both side to form lock rail, Top, bottom and lock

rails shall be provided either side of the panel.

10mm (5mm x 2) thick 20mmwide crossPVC

sheetshallbeprovided asgap insert fortop railand

bottom rails. Panelling of 5mm thck both side

prelim PVC sheet to be fitted in the M.S. frame

welded,sealed to the stiles and rails with 7mm

(5mm + 2 mm) thick x 15mm wide PVC sheet

beading on inner side, and joined togeth with

solvent cement adhesive. An additional 5mm thick

PVC strip of 20mm width is to be stuck on the

interior side of the ‘C” chanel using PVC solvent

adhesive etc. complete as per direction of

Engineering in charge, manufacture’s specification

and rawing. (R&B SOR Item no.10044)

Brick work using common burnt clay building bricks

having crushing strength not less than

33 kg./Sq.Cm. in foundation and plinth in Cement Cmt 13.63 3981.21

Mortar 1:6 (1- Cement : 6 -fine sand)(B)

Conventional (R&B SOR Item no. 06002BA)

Providing 15mm thick cement plaster in single coat

on Rough (Similar)side of single or half brick walls

34 for interior plastering upto floor two level and Smt 411.00 155.61

finished even and smooth in (ii) Cement mortar 1:4

(1-cement :4-sand) (R&B SOR Item no.17002B)

Constructing brick masonry chamber for

underground C.I. Inspection chamber and bends

with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than

38Kg.(Wt. of cover23 Kg.) and Wt. of frame 15Kg. )

(R.C.C. top slabe with 1:2:4 mix (1-cement

:2coarse sand :4-graded stone aggregate 20mm

size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls

and bed concrete etc. complete.(ii) Inside

dimensions 500mm x 700 mm and 450mm deep

for pipe line with one or two inlets.(R&B SOR Item

Providing and fixing Zoloto Gun metal check or

36 non-return fullway wheel valve.(E) 50mm dia.MR No. 12.00 2338.00

Providing and fixing 35 mm thick flush Single door

shutter, solid core Confirming to IS:2202 & ISI

approved manufacture with Anodized Aluminium

section ( door section no 19552-weight not less

than 1.1 kg/mt ) frame size 63.5mm x 38mm

inserted Non teak wood frame inside the

aluminium section for durable grip of hinges(4no

37 each shutter) & Single shutter with required Smt 6.00 4194.60

teakwood batten having 1mm thick lamination on

both side, including cost of Hydraulic Door Closer

Durable Grip shall be providing with both side

15cm long stainless steel handle and necessary

Locking system of , ,fixtures & fastenings etc.

directed by engineer in charge. RA

Providing and fixing 5 mm thick mirror of approved

quality and make size 2700 x 1000 mm with

38 moulding edge by using 4.0 mm thick hard board Smt 9.00 2710.00

and fixing on wall with C. P.brass studs etc.

complete. For all floor. RA

Providing and fixing pre-castRubberDye/steelDye

inter locking concrete block 60mm thick with grade

of concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design

39 Confirming to IS 15658 : 2006 including 35 mm Smt 60.00 680.10

Sand layer for levelling and filling the joint with

sand in proper line and level as per guidlines of

IRC : SP 63-2018 etc. Complete.(R&B SOR Item

Providing and laying broken chine mosaic flooring

for terrace using 12 mm to 20 mm broken piecesof

glazed tilestobelaid overcement mortar 1:3 to plain

or slope and to be tempered to bring mortar creme

40 out upto surface using white cement including Smt 264.00 739.89

rounding off junctions and extending

themupto15cmalongthe wall,clearing with water

and oxalic acid etc. as directed. .(R&B SOR Item

Providing and laying Cement concrete 1:2:4 (

cement : 2 coarse sand : 4 graded stone

41 aggregates 20 mm. nominal size) and curing cmt 27.00 3661.30

complete excluding cost of from work in terrace.

(R&B SOR Item no.05010AA)

Providing, fabricating, and fixing G.I. Powder

coated (parnal) 0.6mm thickness rectangular

rainwater drain channel(gutter), 610 mm wide,

including Dismentaling existing G.I (parnal) and

42 fixing upto 25m height of rooftop ,hooks, brackets, Rmt 260.00 1650.00

supports, bolts, screws, silicone sealant, and all

incidental works, complete in all respects as

directed by the engineer-in-charge. MR

Total amount Rs (in words) Thirty Five lacs Two Thousand Three Hundred and Sixty Eight Rupees

Total amount Rs (in words) Thirty Five lacs Two Thousand Three Hundred and Sixty Eight Rupees

I/We am/are willing to carry out the work at………………………………………….…………….%

above/below percent(Should be written in figures and words) of the estimated rate mentioned

above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

 The rates quoted shall be excluding of all taxes (GST)/ carting complete.

 All works shall be carried out as per specification or as directed.

 The material shall get approved by GCSC EIC, before procurement.

 The quantity may vary as per GCSC requirements.

 The electricity if required for the current work shall be provided by GCSC. Necessary

arrangement for DG set may be done by bidder for the work. Contractor shall make his

own arrangement to carry the same at required site location, under strict supervision and

prior permission of GCSC.

 The quantity if varied, the rates shall be paid for the actual work done on proportional

basis of the specified item.

 Signature of the Contractor with stamp Executive