Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹24.8 LAccepted-AOC | L1 | Accepted-AOC BEING L1 | |
| 2 | L2₹28.9 L+₹2.7 L (10.2%)Rejected-Finance YOL CAMP TEH DHARAMSHALA DISTT KANGRA HP | YOL | KANGRA | HIMACHAL PRADESH | 176052 | L2 | Rejected-Finance OTHER THAN L1 | |
| 3 | L3₹29.6 L+₹3.4 L (12.9%)Rejected-Finance | L3 | Rejected-Finance OTHER THAN L1 | |
| 4 | L4₹30.8 L+₹4.6 L (17.5%)Rejected-Finance | L4 | Rejected-Finance OTHER THAN L1 |
Tender Value
₹27.4 L
EMD Value
₹54,800
Closing Date
26 Jan 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (KH) YOL
GE (KH) YOL, YOL CANTT, HP
Addn/Altns to bldg No. T-11 and Provn of 2x water staging, Provn of steel plate racks at YOL CANTT under AGE B/R-II of GE (KH) YOL
2022_MES_571857_1
GE/Y-55/2022-23
Open Tender
Civil Works
Item Rate
180 days
YOL CANTT
Please refer Tender documents.
9 documents required · 9 mandatory
₹500
GE(KH) YOL
₹54,800
Yes
31 Jan 2023
29 Dec 2022
28 Jan 2023
29 Dec 2022
26 Jan 2023
12 Jan 2023
Amount
SCHEDULE 'A' PART-I :- Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.
Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.
Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.
Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section complete all as specified.
Dismantling timber scantlings 40 sqcm and over in section, in any position, framed work, complete all as specified.
Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.
Demolition of stones or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete, all as specified.
Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.
Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290 Gde E-165, steel workcomplete, all as specified.
Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240s, steel work complete, all as specified.
Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe.290 Gde E-165,
Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 290 Gde E-165, all as specified.
Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30 cm long, diameter of neck 12 to 20mm, complete all as speciied.
Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.
Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.
Aluminium anodized snap grid frame work of size 605 mm x 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/instruction), cutting holes for electrical fittings fixed on an including aluminium tee of size 25 mm x25 mm x1.5 mm as main runner, aluminium tee of size 25mmx25mmx1.25mm as cross runner and aluminium angle of size 25mmx25mmx1.25mm at the perimeter suspended from soffit at approx 900mm centre to centre with hangers 6mm dia galvanized (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanized iron flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including necessary scaffolding and providing and fixing of 12mm thick gypsum board in ceiling fixed with screws as per manufacturer instructions, all as specified and directed.
Pressed steel frames of size 125x60mmx1.25mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.
Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters with two panels and with interlocking rail and and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, all as specified.
Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II.
Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.
Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II
Factory made fully glazed PVC window/ventilator shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; completespecified and directed. Note:- Glass shall be measured and paid separately
Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf. (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel butt hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/13. Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.
Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, all as specified.
Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads, all as specified.
Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each all as specified.
Butt hinges, medium weight, cold rolled, mild steel 50mm long, all as specified.
Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, all as specified.
Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm, fixed, all as specified.
Extruded aluminium alloy handles, fabricated type, anodised, of size 150mm, all as specified.
Extruded aluminium alloy handles, fabricated type, anodised, of size 100mm, all as specified.
Butt hinges, stainless steel medium weight 100mm long, all as specified.
Butt hinges, stainless steel medium weight 75mm long, all as specified.
Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, all as specified.
Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.
Sheet glass 3mm thick ordinary quality and glazing with oil putty/aluminium beads in squares, not exc. 0.5sqm in each pane, complete all as specified.
3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane, complete all as specified.
Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.
Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC subbase complete, all as specified.
Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair to receive top surface, all as specified.
Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.
Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.
Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.
Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.
Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).
Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For roughly finished flat surfaces of concrete, all as specified.
RCC M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement shall be measured and paid separately.
Reinforced cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, lintel, over 1.50m span all as specified.
PCC M-15, nominal mix, B-0 using 12.5mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.
TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.
TMT bars 5mm dia and over upto and including 10mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.
Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), all as specified. Note:- Locally available slate stone not shall be used.
Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.
Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.
Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc., all as specified.
Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.
Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) on other than fair faces of brick wall or on stone masonry surfaces, surface finished even and smooth without using extra cement, all as specified.
Supply only integral water proofing compound, complete all as specified.
Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper, complete, all as specified.
Preparation of old plastered wall surfaces and applying two coats of oil bound distemper, complete, all as specified.
Preparation of newly plastered wall surfaces and applying two coats of cement base paint complete, all as specified.
Complete removal of exiting treatment and applying two coats of cement base paint including preparation of surface complete, all as specified.
Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.
Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.
Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.
Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.
Bib tap with Wall Flange, 15mm bore, cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair, complete, all as specified.
Stop/Angle valve, cast copper alloy, chromium plated, fancy type with wall flange, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs, complete, all as specified.
Brass Chromium Plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified.
Soap dish, chromium plated, fixed to plugs with chromium plated, brass screws, all as specified.
Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified
Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.
Gun metal, globe or gate valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed in repair complete, all as specified.
Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed in repairs complete, all as specified.
Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete, including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair complete all as specified.
Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with fixing bolts, chromium plated mild steel hinges device and seat cover with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, (excluding PVC valveless, syphonic action type flushing cistern, ball valve, float and handle with brackets with PVC dia flushing pipe, anti-syphonage pipe), fixed in repair, complete, all as specified.
Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed in repairs, complete all as specified.
Vitreous China Urinal, Half stall type, white including PVC waste pipe, including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe including fixing supply pipe to flushing cistern trap and including 32mm bore PVC waste pipe and fixed in repair, complete all as specified.
PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 110mm complete, including taking down old pipe, all as specified.
PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 75mm complete, including taking down old pipe, all as specified.
PVC (SWR) junction single, (Single T) equal or unequal, Branch piece 110mm bore, provided with oval access door all as specified.
PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.
PVC (SWR) bends any radius, 110mm bore with ovel access door, and jointing with solvent cement, complete all as specified.
PVC (SWR) bends any radius, 75mm bore with ovel access door, and jointing with solvent cement, complete all as specified.
Plain cement concrete M-10 nominal mix, type C-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains all as specified.
Aluminium (diecast) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair, complete all as specified.
Hand Shower (Health Faucet) (ABS Body) mild steel chromium plated suitable for 15mm dia pipe, with 1.25 Meter Long PVC Tube & Wall Hook, complete all as specified.
15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in repair, complete all as specified.
Taking down of aluminium door shutter and window shutter with frame including with all fittings, repairing and refixing the aluminium door shutter with frame in serviceable condition in same opening.
Supply fabricate & fix in position aluminum powder coated (Minimum thickness of powder coating 50 micron of approved colour) fixed window (two shutters glazed & two small sliding glazed shutter) with frame, glazed with 4mm thick tinted glass and wire gauge with stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, including rubber bead joining cleat for fixing in position, concealed type lock for all shutter, PVC roller etc all as specified below, complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50mm (section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50mm (section No 20832) (c) Top & side Members of shutter section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20738) (d) Shutter Interlock section shall be of size 18.00 x 40.00x1.45mm (section No 20737) (e) Bottom Members of shutter section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736).
Natural colour 15 micron anodized aluminium sliding window three track with chowkhat and aluminium grill of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a)Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM. (b)Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c)Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e)including 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets and stainless steel wire cloth complete . (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos).
Natural colour 15 micron anodized aluminium door chowkhat with shutter of approved design with frame, partly glazed with 5mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead jointing cleat for fixing in position aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size etc. all as specified below. The member shall made out of extruded aluminium sections comprising of:- (a) frame (top & side) section shall of size 101.60 x 44.75 x 2.40mm (section No. 14021). (b) Shutter vertical member section shall of size 85.00 x 44.45 x 2.00mm (section No. 19560). (c) Shutter top member section shall of size 83.5 x 44.45 x 2.00 mm (section No. 19581). (d) Shutter lock rail middle member section shall of size 150.00x44.45x3.00mm (section No. 19596). (e) Shutter bottom member section shall of size 150.00x44.45x3.10mm (section No. 19584). (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (section No. 19370).
Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified.
5mm thick PVC sheet fillet with 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete, all as specified and directed.
Chequered cement concrete tiles machine pressed of size 20cmx20cmx 25mm thick with grey cement, set jointed & pointed in neat cement slurry no pigment to match the shade of the slab in floors, complete all as specified.
Plain cement concrete M-7.5, nominal mix, type D-2, using 40 mm graded mechanically crushed stone aggregate as in sub base floor, 75 mm thick, surface finished even and fair to receive top surface, all as specified.
Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all as specified.
Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), all as specified.
0.63 mm thick plain galvainsed mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete, all as specified.
Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds etc. all as specified.
Demolition and breaking up drain pipes (Salt glazed stone ware, AC or RCC pipes) 150mm dia and removal of demolished materials from the site as directed.
Reinforced concrete pipes, class NP2, laid and jointed with cement mortar 1:2, complete with collars, bore of pipe 150mm, all as specified.
Plain cement concrete M-7.5 type D-2 nominal mix using 40mm graded aggregate as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for internal dia of pipe 150mm, all as specified. Note:- (i) The unit rate include for use of form work. (ii) For width and depth of PCC bed - refer preamble (a) (i) (ii) on page 356 of SSR Pt-II). (iii) Haunching shall be as per MES SSR-part-I/Part-II
Cutting into existing manholes for connecting new drains, 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round 3/4 channel) in cement concrete M-15 type B-1 smooth, finished and reforming benching as required complete all as specified and as directed.
Steel plate rack of size 900mmx750mmx250mm made of stainless steel 1mm thick fixed over 40cm long MS angle of size 25mmx25mmx3mm-02 Nos each on walls, complete all as specified and directed.
Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, all as specified.
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) in rough finished surface of concrete complete all as specified.
Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) on external fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.
Three coats of white wash on newly plastered or previously undecorated surfaces of walls including preparation of surfaces complete, all as specified.
Excavation in trenches not exc 1.5 metres wide and n.exc 1.5 metres deep and getting out in any type of soil, all as specified.
Returning filling in including spreading, levelling, watering and well ramming in layers not exc. 25cm thick each layer of soil all as specified.
Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.
Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified.
Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, all as specified.
Plain cement concrete M-10, nominal mix, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).
Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, all as specified.
Brass Chromium Plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed, complete all as specified.
Stop/Angle valve, cast copper alloy, chromium plated, fancy type with wall flange, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions, complete, all as specified.
Bib tap with Wall Flange, 15mm bore, cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions, complete, all as specified.
Angular Stop cock with Wall Flange, cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed complete, all as specified.
Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, all as specified.
Gun metal, globe or gate valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions, complete all as specified.
Taking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including light fiitings any type, switches, sockets, holders, (batten or pendent type), ceiling rose, switch board, bell/buzzer, bell push, tube light fitting, regulator etc. and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes and all as specified and directed.
Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified.
Point wiring with 1.5 Sqmm copper conductor FR-LSH (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit medium grade, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed pressed steel/ cast iron of suitable sizes terminal boxes made from 1.60mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet for one light point or one fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed. Note:- i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. ii) The wire from switch board to ceiling rose shall be of 2x1.5Sqmm +1x1.5sqmm rates for the same shall deemed to be included in item.
All as per serial item No '126' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.
All as per serial item No '126' above, but for one 3 pin 5 Amps socket outlet on the independent board, all as specified and directed.
All as per Srl item No. '126' hereinbefore but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.
Switch piano flush type, single pole, one way, 5 Amps 230V, all as specified.
Switch socket combination Two -in -One 3 Pin, 5 Amp Amp flush type, all as specified.
Switch socket combination Two -in -One 3/5 Pin, 5 Amp & 15 Amp flush type, all as specified.
Ceiling fan regulator step type, electronic type on the existing phenolic laminated sheet etc. varying 5 Speeds 230 Volts, 50Hz, suitable for 1200/ 1400 mm sweep ceiling fans, all as specified.
Ceiling rose, three phase, 65x20mm, PVC/Polycarbonate, insulated body, all as specified.
Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral, 8 way, 415 volts with 200 Amp rated bus bar, double door with detachable gland plate, all as specified.
M & L for vertical DB factory made TPN 4 Way, MCCB as incomer and MCB SP as out going, double door DB IP 43 protection level, incl Blanking plate, lugs etc complete and neutral link with one MCCB 4 pole 415V 63 Amps rating with rupture capacity 16KA incl connection, fixing flushed to wall, necessary grouting, making good with CM 1:4 and painted to match exisitng wall color complete including fixed in repair.
MCB SP 6 to 40 Amp, 240 Volts, 10 KA, C series, all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.
MCB SPN 32 Amp, 240 Volts, 10 KA C series, all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.
MCB TPN 63 Amp, 240 Volts, 10 KA C series including taking out old, all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.
Replacement of Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded FRLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into and including surface PVC casing & capping of suitable size with all fittings/ accessories, junction boxes 1 to 4 way 25mm dia and connected to common earth dolly, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).
Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver all in one fixture, 10 watt LED and making connection with 2 core twisted copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete including taking down old unserviceable.
Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver all in one fixture, 20 watt LED and making connection with 2 core twisted copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete including taking down old unserviceable.
Basic all purpose surface and ceiling mounted LED Venus Neo panel 2x2, 36W 865 environmental friendly, new generation, aesthetically, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source and including connecting up with twin core twisted flexible copper conductor cable with suitable size.
Taking down ceiling fans//exhaust fan of 1200/250/300mm sweep of any make/ Model from fan hook/ wall dismentling blade opening of motor for overhauling/servicing, and then properly cleaning alll parts and greasing, oiling of bush & bearings after opening of the fan including reassembling and Painting of ceiling fans/exhaust fan after due preparation complete at site with super enamel synthetic white paint by spray gun including filling cavities with filler, one coat after cleaning all dust etc and writing MES No with black paint and than re-hanging and reconnecting of fan with new flexible cord of suitable size from ceiling rose to connector, complete all as directed by Engineer-in-Charge.
Material and labour for rewinding of ceiling fan of any make/model/sweep including removal of existing burnt winding carefully from slots, cleaning the slots throughly with suitable cleaing agent, applying slot inslation and rewinding with super enameled insulated copper wire of same gauge / same number of turns as existing and connecting the coil suitable to operate on 230VC, single phase, AC supply including all winding, insulating material and impregnation of insulating varnish as specified of any make, type, model and applying air drying the winding throughly including transportation from site of rewinding 1200/1400mm sweep, complete all as specified.
XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 50 Sqmm 4 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying, including taking out old cable, complete all as specified.
M&L for 40mm dia GI pipe light grade as in trenches, across road or pole including taking up or down, complete all as specified and directed.
Sand cushioning to under ground cables, 8 cm thick layer before laying and testing the cable and 15 cm thick after laying and testing of the cable in trenches complete all as specified in Clause 19.75 of MES SSR 2020 Part-I and directed by Engr-in-Charge.
Sub class 'B' bricks old size, as cable protection cover, laid dry, flat, transversally along the length of cable, on sand cushioning, with width equal to the length of the brick, complete all as specified and directed.
Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5 metre long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.
Supply and fixing of electric water heater, storage type steel body with copper inner tank and heating element upto 2KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., complete all as specified and directed.
Supply and fix double pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole MCB of 20Amps rated, complete all as specified and directed.
Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral, 12 way, 415 volts with 200 Amp rated bus bar, double door with detachable gland plate, all as specified.
Supply and fixing LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, complete all as specified and directed
1100 volts grade heavy duty cable PVC insulated aluminium solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular stranded conductor size of 10 sqmm, complete all as specified.
Cutting existing steel tubing for alterations or additions (Each cut measured) for 25 to 32mm mm bore pipe.
Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. laid in trenches complete, all as specified and directed.
M/S AMOLAK SINGH AND SONS
Ms Sunil Kumar
m/s Sohan singh barwal and Brothers
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .