Renovation of Bath and Toilet in rooms of Eastern and Western side wings and granite flooring to VIP suite at Guest House-1 (Kurinji Building)

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.

30 mm thick plain PVC door shutters

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door

75 mm bend

110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

Renewing glass panes and refixing existing wooden fillets:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :

75 to 80 mm dia pipe

100 mm dia pipe

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

40 mm dia

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

25 to 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.

15 mm nominal bore with 45 cm length

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

For pipes 100 to 250 mm diameter

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and Fixing of Mosquito Net shutter with 20mm width powder coated aluminum frame to the fixed on the wood/MS frame on the opening as per site condition.The frame shall be two vertical and three horizontal. The shutter made of stainless steel materials and operated with mini fibre hinges and with fibre stopper for 3 sides etc complete. The rate including cost of all materials and labour charges etc complete.

Proviidng & Fixing 100 mm PVC pipe as per the direction of Engineer-in-charge.

Dismantling the exisiting water closet without damaging the existing sewer line etc complete.

"Cutting holes upto 30x30 cm in walls including making good the same : with F.P.S. bricks."

Providing and fixing PVC cowl to the PVC pipes etc complete as per the direction of Engineer-in-charge. 75 mm Cowl

Providing and fixing PVC cowl to the PVC pipes etc complete as per the direction of Engineer-in-charge. 110 mm Cowl

Providing & fixing circular PVC floor trap to pvc pipe etc complete.

Providing and fixing Stainless steel gratings etc complete 100 mm

Providing and fixing PVC corner beeding to wall tiles atc complete.

Providing & laying 20 mm stone jelly to site etc complete

Providing and fixing of 75mm dia (Finolex or Avonplast-6kg/cm2) unplasticised Rigid PVC soil pipes conforming to IS :13592 Type A including jointing with seal ring conforming to S :5382 leaving 10mm gap for thermal expansion. (i) Single socketed pipes

Providing and fixing SS gratting to floor tiles etc complete. 125 mm dia

Providing and fixing Ist quality ceramic glazed wall tiles (Premium) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Size of tile -0.30m x 0.60m. The model of tile should be got approved from the Engineer-in-charge/E.M.Dept. (Kajaria,Somanya,Nitco,RAK or equivalent brand)

Providing and laying Ceramic glazed floor tiles (Preminum) of size 300x300 mm or 380x380mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. Size of tile 0.30m x 0.30m or 0.38mx0.38m. The model of tile should be got approved from the Engineer-in-charge/E.M.Dept. (Kajaria,Somanya,Nitco,RAK or equivalent brand)

Providing and fixing wall mounted European type water closet pan with seat and lid of size 50.50x37x38 cm Constellation-Hindware, Jaquar or equivalent brand etc complete as per the direction of Engineer-in-charge. The model of European water closet should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing PVC 100mm single Y with door fiiting to pipe etc complete as per the direction of Engineer-in-charge (Avonplast-Finolex or equivalent make).

Providing and fixing PVC 75mm single Y with door fiiting to pipe etc complete as per the direction of Engineer-in-charge (Avonplast-Finolex or equivalent make).

Providing and fixing PVC 100mm double Y with door fiiting to pipe etc complete as per the direction of Engineer-in-charge (Avonplast-Finolex or equivalent make).

Providing and fixing Mirror double arm SS wall mounted reversible plain/magnifying (X3) pivotal mirror etc complete.

Providing and fixing half pedestal wash basin wall hung of size 550x400x195mm with accessories of continental-Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The pillar cock FON-4002 with 140mm extension body (Jaquar, Hindware or equivalent brand) .The model of wash basin should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing stainless steel shelf tray of ACN-1177N of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS shelf tray should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing stainless steel towel ring of ACN-1121 BN of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS shelf tray should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing stainless steel health faucet (Hand shower) ALD-573 with 8mm dia, 1.20 meter long flexible tube & wall hook and SS two way tap of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS health faucet and two way tap should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing stainless steel wall mixer tap to pipe etc Continental - 267 KN of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS wall mixer tap should be got approved from the Engineer-in charge/E.M.Department.

Providing and fixing stainless steel towel rod of 600 mm ACN-1111 SM of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS towel rod should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing stainless steel over head shower of dia 100mm round shape single flow (ABS body chrome plated with grey face plate) with rubit cleaning system of QTTS-1989 of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS shower should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing stainless steel shower arm dia 20mm and 450mm long round shape with 90' bend of SHA-479L450 of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS shower arm should be got approved from the Engineer-in-charge/E.M.Department.

Providing and fixing stainless steel long nose bib cock of Jaquar, Hindware or equivalent brand etc as per the direction of Engineer-in-charge. The model of SS long nose bib cock should be got approved from the Engineer-in-charge/E.M.Department.

K VILLAYUDHAM

CIS GLOBAL INFRATECH PVT LTD

ORIENTAL INTEGRATED FACILITY MANAGEMENT PVT. LTD.