NEW CONSTRUCTION OF URBAN HAAT PROJECT BUILDING AT RAJKOT (SECOND ATTEMPT)

Name of work:- NEW CONSTRUCTION OF URBAN HAAT PROJECT BUILDING AT RAJKOT

Item Quantities Item of Work Tendered Rates Unit Total Amount

Item Quantities Item of Work Tendered Rates Unit Total Amount

No. Estimated may be In Figures In Words according to

more or less Rs. estimated quantity

1 9714.00 Cum Excavation for foundation up to 1.5 mt. depth including 117.26 Rupees One Cum

sorting out and stacking of useful materials and disposing Hundred

of the excavated stuff up to all lead. (A) Loose or soft soil Seventeen &

Paise Twenty Six

2 2933.00 Cum Excavation for foundation 1.5 to 2.0 mt. depth including 162.91 Rupees One Cum

sorting out and stacking of useful materials and disposing Hundred Sixty

of the excavated stuff up to all lead. (B) Dense or Hard Soil Two & Paise

3 5866.00 Cum Excavation for foundation for depth from 2.0 m to 3.0 m 275.28 Rupees Two Cum

including sorting out and stacking of useful materials and Hundred Seventy

disposing off the excavated stuff upto all lead.(D) Hard Five & Paise

4 4310.00 Cum Excavation for foundation for depth from 3.0 m to 5.0 m 310.12 Rupees Three Cum

including sorting out and stacking of useful materials and Hundred Ten &

disposing off the excavated stuff upto all lead. (E) Soft Paise Twelve

Rock Not Blasting

5 6635.00 Cum Filling available excavated earth (excluding rock) in 130.39 Rupees One Cum

trenches. plinth, sides of foundations etc. in layers not Hundred Thirty &

exceeding 20 cm. in depth consolidating each deposited Paise Thirty Nine

layer by ramming and watering.

6 1.00 Hect Clearing and grubbing road land including uprooting rank 34796.29 Rupees Thirty Hect

vegetation grass bushes, shrubs, sapling and trees girth up Four Thousand

to 300 mm removal of stumps of trees cut earlier and Seven Hundred

Ninty Six & Paise

disposal of unserviceable materials(D) By mechanical

means in area of thorny jungle.

7 30000.00 Cum Carriage of extra earth and debris from site upto 15 km 121.20 Rupees One Cum

distance including JCB & dumper and disposal of un Hundred Twenty

serviceable materials in approved dumping site. The height One & Paise

is taken approximate 3 mt. considered it may vary for actual

site measurement after the surveying.

8 292.00 Cum Providing and laying cement concrete 1:2:4 (1- Cement : 2- 3633.58 Rupees Three Cum

Coarse sand : 4- graded stone aggregates 20 mm nominal Thousand Six

size) and curing complete excluding cost of formwork in (A) Hundred Thirty

Foundation and Plinth

Fifty Eight Only

9 796.00 Cum Providing and laying cement concrete 1:3:6 (1- Cement : 3- 2957.89 Rupees Two Cum

Coarse sand : 6- graded stone aggregates 40 mm nominal Thousand Nine

size) and curing complete excluding cost of formwork in (A) Hundred Fifty

Foundation and Plinth

Eighty Nine Only

10 1116.00 Cum Providing and laying in position Ready Mixed M-250 grade 6011.52 Rupees Six Cum

concrete for reinforced cement concrete work , using cement Thousand Eleven

content as per approved Design Mix manufactured in fully & Paise Fifty Two

automatic batching plant and transported to site of work in transit Only

mixer for a lead up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

Note: Design Mix should be carried out only as per the cement

content specified in IS-456. No deviation in cement content will be

A) M25 - For Foundation

11 147.00 Cum Providing and laying in position Ready Mixed M-250 grade 8294.12 Rupees Eight Cum

concrete for reinforced cement concrete work , using cement Thousand Two

content as per approved Design Mix manufactured in fully Hundred Ninty

automatic batching plant and transported to site of work in transit Four & Paise

mixer for a lead up to 10 kms having continuous agitated mixer, Twelve Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

A) M25 - For Column for floor upto two level.

12 44.00 Cum Providing and laying in position Ready Mixed M-250 grade 8333.51 Rupees Eight Cum

concrete for reinforced cement concrete work , using cement Thousand Three

content as per approved Design Mix manufactured in fully Hundred Thirty

automatic batching plant and transported to site of work in transit Three & Paise

mixer for a lead up to 10 kms having continuous agitated mixer, Fifty One Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

A) M25 - For Column for First floor for above floor two level.

13 679.00 Cum Providing and laying in position Ready Mixed M-250 grade 6466.02 Rupees Six Cum

concrete for reinforced cement concrete work , using cement Thousand Four

content as per approved Design Mix manufactured in fully Hundred Sixty

automatic batching plant and transported to site of work in transit Six & Paise Two

mixer for a lead up to 10 kms having continuous agitated mixer, Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

A) M25 - For Beams for Ground floor upto floor two level.

14 171.00 Cum Providing and laying in position Ready Mixed M-250 grade 6505.41 Rupees Six Cum

concrete for reinforced cement concrete work , using cement Thousand Five

content as per approved Design Mix manufactured in fully Hundred Five &

automatic batching plant and transported to site of work in transit Paise Forty One

mixer for a lead up to 10 kms having continuous agitated mixer, Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

A) M25 - For Beams for First Floor above floor two level.

15 1131.00 Cum Providing and laying in position Ready Mixed M-250 grade 7621.46 Rupees Seven Cum

concrete for reinforced cement concrete work , using cement Thousand Six

content as per approved Design Mix manufactured in fully Hundred Twenty

automatic batching plant and transported to site of work in transit One & Paise

mixer for a lead up to 10 kms having continuous agitated mixer, Forty Six Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

Note: Design Mix should carried out only as per the cement

content specified in IS-456. No deviation in cement content will be

A) M25- For Slab for Ground floor upto floor two level.

16 618.00 Cum Providing and laying in position Ready Mixed M-250 grade 7660.85 Rupees Seven Cum

concrete for reinforced cement concrete work , using cement Thousand Six

content as per approved Design Mix manufactured in fully Hundred Sixty &

automatic batching plant and transported to site of work in transit Paise Eighty Five

mixer for a lead up to 10 kms having continuous agitated mixer, Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

Note: Design Mix should carry out only as per the cement content

specified in IS-456. No deviation in cement content will be

A) M25-For Slab for First floor above floor two level.

17 945.00 Cum Providing and laying in position Ready Mixed M-250 grade 8142.62 Rupees Eight Cum

concrete for reinforced cement concrete work , using cement Thousand One

content as per approved Design Mix manufactured in fully Hundred Forty

automatic batching plant and transported to site of work in transit Two & Paise

mixer for a lead up to 10 kms having continuous agitated mixer, Sixty Two Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

Note: Design Mix should carried out only as per the cement

content specified in IS-456. No deviation in cement content will be

A) M25-For Walls from top of foundation level upto floor two level.

18 44.00 Cum Providing and laying in position Ready Mixed M-250 grade 8182.01 Rupees Eight Cum

concrete for reinforced cement concrete work , using cement Thousand One

content as per approved Design Mix manufactured in fully Hundred Eighty

automatic batching plant and transported to site of work in transit Two & Paise One

mixer for a lead up to 10 kms having continuous agitated mixer, Only

manufactured as per mix design of specified grade for reinforced

cement concrete work including pumping of R.M.C. from transit

mixer to site of laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of admixtures in

recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall be

The Rate shall be inclusive of labour for keeping embedments if

any, wherever required while casting, including the cost of

centering, shuttering, formwork, staging, scaffolding (rates for

centering, shuttering, formwork, staging, scaffolding for

considering rates should be for clear floor height of 4.5mtrs. Extra

staging above clear floor height of 4.5mtrs will be paid extra in

relevant tender item) concrete cover blocks, admixtures,

materials, labour etc complete but excluding the cost of

reinforcement steel. All material shall confirm to relevant IS

standards. For all Civil, Plumbing, Electrical & infrastructure

Note: Design Mix should carried out only as per the cement

content specified in IS-456. No deviation in cement content will be

A) M25-For Walls from for First Floor above floor two level.

19 7.00 Cum Providing and laying 1 : 2 : 4 RCC concrete for reinforced 6487.59 Rupees Six Cum

concrete Chhajjas not exceeding 1Ocm. thickness upto Thousand Four

floor two level including finishing the exposed surfaces with Hundred Eighty

cement mortar 1:3 (1-cement, 3 Fine sand) to give a

Fifty Nine Only

smooth and even surface centering and formwork and

curing complete excluding cost of reinforcement.

20 10.00 Cum Providing and laying 1 : 2 : 4 for R.C.C lintel including 9742.36 Rupees Nine Cum

finishing smooth with, curing etc. complete including the Thousand Seven

cost of formwork but excluding the cost of reinforcement. Hundred Forty

Thirty Six Only

21 36.00 Cum Providing and laying controlled cement concrete M.200 and 8890.02 Rupees Eight Cum

curing complete including the cost of formwork and Thousand Eight

reinforcement for reinforced concrete work in Staircases Hundred Ninty &

excluding landing upto floor two level

22 15.00 Cum Providing and laying controlled cement concrete M.200 and 8929.41 Rupees Eight Cum

curing complete including the cost of formwork and Thousand Nine

reinforcement for reinforced concrete work in Staircases Hundred Twenty

excluding landing above floor two level for first floor

23 221.00 Rmt Providing throating or plaster drip and moulding to R.C.C. 41.66 Rupees Forty Rmt

Chhajja. One & Paise

24 217.00 Sqmt Providing and fixing in expansion joint 100 mm thick 2982.06 Rupees Two Sqmt

expansion joint board of best quality and approved make Thousand Nine

including cutting to required size and shape at all levels etc. Hundred Eighty

Two & Paise Six

complete as directed.

25 73.00 Sqmt Applying and providing Expansion joint sealing System on 4772.00 Rupees Four Sqmt

100 mm vide joint including cleaning of expansion joint by Thousand Seven

mechanical means provision of adhesive and flexible Hundred Seventy

membrane with required bond length as per manufacturer

specification and 4mm thick aluminium strip covering with

one side slated and bolted with suitable system, inclusive of

all manpower, machinery and material as per specification

and as directed.

26 8.00 Sqmt Providing upto floor two level precast cement concrete 733.26 Rupees Seven Sqmt

cover 1:2:4 mix (1- Cement: 2- coarse sand: 4-graded Hundred Thirty

stone aggregate 6mm nominal size) reinforced with 1.6 Three & Paise

Twenty Six Only

mm dia. Mild steel wire including roughening, cleaning,

fixing and finishing in cement mortar 1:3 and curing

complete. (A) 50mm thick

27 381386.57 Kg Providing T.M.T Fe 500 D bar reinforcement for R.C.C. 76.21 Rupees Seventy Kg

work including bending, binding and placing in position Six & Paise

complete up to floor two level. - Ground floor Twenty One Only

28 87925.32 Kg Providing T.M.T Fe 500 D bar reinforcement for R.C.C. 77.21 Rupees Seventy Kg

work including bending, binding and placing in position Seven & Paise

complete up to floor two level. - First floor . Twenty One Only

29 25.00 Cum Brick work using common burnt clay building bricks having 4021.02 Rupees Four Cum

crushing strength not less than 35 kg./Sq.Cm. in Thousand

foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 - Twenty One &

fine sand)(B) Conventional

30 664.00 Cum Brick work using common burnt clay building bricks having 4295.99 Rupees Four Cum

crushing strength not less than 35 kg./Sq.Cm. in super Thousand Two

structure in Cement Mortar 1:6 (1- Cement : 6 -fine Hundred Ninty

sand)(B) Conventional for Ground floor upto floor two level.

Ninty Nine Only

31 950.00 Cum Brick work using common burnt clay building bricks having 4336.18 Rupees Four Cum

crushing strength not less than 35 kg./Sq.Cm. in super Thousand Three

structure in Cement Mortar 1:6 (1- Cement : 6 -fine Hundred Thirty

sand)(B) Conventional For First Floor for above floor two

32 30.00 Cum Brick work using common burnt clay building bricks having 4376.37 Rupees Four Cum

crushing strength not less than 35 kg./Sq.Cm. in super Thousand Three

structure in Cement Mortar 1:6 (1- Cement : 6 -fine Hundred Seventy

sand)(B) Conventional For Above First Floor

33 320.00 Sqmt (i) Half brick masonry in common brunt clay building bricks 640.33 Rupees Six Sqmt

having crushing strength not less than 35 Kg/Sq.Cm. in Hundred Forty &

Cement mortar 1:4 (1- Cement: 4 -coarse sand) in super Paise Thirty

structure (B) Conventional upto floor two level. (Ground

34 761.00 Sqmt (i) Half brick masonry in common brunt clay building bricks 680.82 Rupees Six Sqmt

having crushing strength not less than 35 Kg/Sq.Cm. in Hundred Eighty &

Cement mortar 1:4 (1- Cement: 4 -coarse sand) in super Paise Eighty Two

structure (B) Conventional above two level. (First floor)

35 140.00 Sqmt UPVC window : P & F UPVC WINDOW with km06 super 9847.50 Rupees Nine Sqmt

system with 5-10-5 clear glass with clear white section with Thousand Eight

slider lock ,fly screen sash with handle and roller as per Hundred Forty

manufacture detail specification and sections using

mosquitos net inside complete. (finesta or approve make)

36 154.00 Sqmt UPVC Ventilator with glass louvers - P & F UPVC 11245.34 Rupees Eleven Sqmt

WINDOW with km06 super system with 5-10-5 clear glass Thousand Two

with clear white section with slider lock ,fly screen sash with Hundred Forty

handle and roller as per manufacture detail specification

Thirty Four Only

and sections using mosquitos net inside complete. (finesta

or approve make)

37 52.00 Sqmt Providing & fixing both side laminated min 35mm (+/-2mm) 5441.88 Rupees Five Sqmt

th. fully solid flush door with laminate finished door as Thousand Four

shown in the drg. Size of each door shall be as per the Hundred Forty

dimensions given in the drawing. The edge of the shutter

Eighty Eight Only

should be surrounded with wooden polished bidding/

laminate. Rate shall include necessary approved mortise

locking systems, SS Handle pair, Door closer (Heavy duty

or equivalent), gaskets, knob, stopper & miscellaneous

hardware items. Including all materials and labour etc.

complete as per detail drawing and instruction of engineer-

in charge and consultant.

38 860.00 Sqmt Providing and fixing rolling shutters of approved make 3503.41 Rupees Three Sqmt

made of 80 mm wide G.I. laths inter-locked together Thousand Five

through their entire length and jointed together at the ends Hundred Three &

Paise Forty One

by end locks mounted on specially designed pipe shaft with

bracket plates, guide channels and arrangements for inside

and outside locking with push-pull operation complete but

excluding the cost of hood cover and spring. (A) Shutters

having width below 3.5.M. including providing 60 cm wide

grill area throughout the width.

39 43.00 Sqmt Providing and fixing FRP frame size 100x50 mm and 28mm 2377.76 Rupees Two Sqmt

thick FRP depress panel shutter having extra reinforcement Thousand Three

on sides & edges in Gel coat finish. The core of the shutter Hundred Seventy

& frame is to be filed up with injected fire-retardant grade

Seventy Six Only

polyurethane foam done in situ along with embedded

wooden pieces for stiffening & also taking hinges & fixtures.

The whole FRP frame & shutter is to be water proof

weather proof, termite proof & resistance to mild acid/alkali.

Rates are to be inclusive of S.S. hinges with necessary

screws & aluminium fixtures& fastenings & fastener sleeve.

40 4.00 No. DOOR : GLASS DOOR : Providing and fixing glass door 48783.00 Rupees Forty No.

with patch fitting as shown in the drg. Door shall consist of Eight Thousand

approved make 12mm thk. toughened clear float glass with Seven Hundred

pre-fitted necessary hardware of Enox / Ozone make for

smooth swinging action. Rate shall include necessary

approved locking systems, S.S. brush finished `H'' type

Handle pair, floor springs (Heavy duty or equivalent),

gaskets & miscellaneous hardware items. Including all

materials and labour etc. complete as per detail drawing

and instruction of engineer-in charge and consultant.

41 7440.00 Sqmt Providing 15mm thick cement plaster in single coat on 153.83 Rupees One Sqmt

Rough (Similar)side of single or half brick walls for interior Hundred Fifty

plastering upto floor two level and finished even and Three & Paise

smooth in (iii) Cement mortar1:4 (1-cement:4-sand)For

Ground floor for upto floor two level

42 6900.00 Sqmt Providing 15mm thick cement plaster in single coat on 177.22 Rupees One Sqmt

Rough (Similar)side of single or half brick walls for interior Hundred Seventy

plastering upto floor two level and finished even and Seven & Paise

Twenty Two Only

smooth in (iii) Cement mortar1:4 (1-cement:4-sand)For

First floor for above floor two level

43 290.00 Sqmt Providing 15mm thick cement plaster in single coat on 195.19 Rupees One Sqmt

Rough (Similar)side of single or half brick walls for interior Hundred Ninty

plastering upto floor two level and finished even and Five & Paise

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) for

44 4220.00 Sqmt 20mm thick sand faced / Mala cement plaster on walls upto 302.24 Rupees Three Sqmt

height 10 metres above ground level consisting of 12mm Hundred Two &

thick backing coat of C.M. 1:3 (1-cement : 3-sand) and Paise Twenty

8mm thick finishing coat C.M. (1:1) etc complete including

necessary grooves as per Engineer in Charge.

45 10100.00 Sqmt Providing 10mm thick cement plaster in single coat on 129.34 Rupees One Sqmt

brick/concrete walls for interior plastering upto floor two Hundred Twenty

level and finished even and smooth in (i)Cement mortar 1:3 Nine & Paise

Thirty Four Only

(1-cement:3-sand) Ground floor for upto floor two level.

46 3200.00 Sqmt Providing 10mm thick cement plaster in single coat on 150.66 Rupees One Sqmt

brick/concrete walls for interior plastering upto floor two Hundred Fifty &

level and finished even and smooth in (i)Cement mortar 1:3 Paise Sixty Six

(1-cement:3-sand) for first floor above floor two level.

47 4220.00 Sqmt Providing & applying on Wall exterior/ interior Surface 565.60 Rupees Five Sqmt

texture granules finish of Bakelite Hylam Limited (No.21- Hundred Sixty

trowelled over 20mm thick Mala finished / sand faced

cement plastered (Two coat of 12mm in CM 1:3 & 8mm

coat in CM:1:1) sub strata to get an average finish coat

thickness of 0.08 to 1.2mm comprising of three

components viz Dry granules, Granules bonding agents

and top coat of glossy finish ( Dry granules shell be made

from silica sand pigments, chiefly inorganic) homopolymer

emulsion mix etc. of Bakelite hylam product etc. and top

coat made from solvent based acrylic polymer of Bakelite

hylam product including scaffolding. Including providing

48 2510.00 Sqmt necessary

Proving 20grooves

mm thickin cement

surface plaster

as per instruction in over

in C M 1 : 3 charge.

RCC 349.46 Rupees Three Sqmt

slab using water proofing compound as directed upto 10 Hundred Forty

mt. height. Nine & Paise

49 2510.00 Sqmt Providing & fixing half round clay tiles (Terracotta) over 1439.25 Rupees One Sqmt

RCC slab including fixing the tiles with chemical mortar Thousand Four

including necessary scaffolding height upto 10 mt. size of Hundred Thirty

tiles 13 cm x 18 cm

Twenty Five Only

50 4720.00 Kg Providing and fixing M.S. grills of required pattern to 110.33 Rupees One Kg

wooden frames of windows etc. with M.S. flats at required Hundred Ten &

spacings and frame all around, square or round bars with Paise Thirty

round headed bolts and nuts or by screws including

Applying one coat of metal priming coat over new steel and

other metal surface after and including preparing the

surface by thoroughly cleaning, oil, grease, dirt and other

foreign matter and scoured with brushes fine steel wood,

scrapers and sand paper with ready mixed priming paint

brushing red lead over that applying Painting two coats

(excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even

shade including cleaning the surface of all dirt, dust and

other foreign matter. (A) Plain Grill.

51 17540.00 Sqmt Applying two coats of putty & two coats of primer of 121.25 Rupees One Sqmt

approved brand and manufacture on new wall surface to Hundred Twenty

give an even shade including thoroughly brushing the One & Paise

Twenty Five Only

surface free from mortar dropping and other foreign matter

and sand papered smooth. Wall painting (two coats) with

plastic emulsion paint of approved brand and manufacture

on undecorated wall surface to give an even shade

including thoroughly brushing the surface free from mortar

droppings and other foreign matter and sand papered

52 10100.00 Sqmt Applying two coats of putty & two coats of primer of 123.48 Rupees One Sqmt

approved brand and manufacture on new wall surface to Hundred Twenty

give an even shade including thoroughly brushing the Three & Paise

Forty Eight Only

surface free from mortar dropping and other foreign matter

and sand papered smooth. Wall painting (two coats) with

plastic emulsion paint of approved brand and manufacture

on undecorated wall surface to give an even shade

including thoroughly brushing the surface free from mortar

droppings and other foreign matter and sand papered

smooth. For First Floor

53 2050.00 Sqmt Applying paint on new steel surfaces and other metal 122.66 Rupees One Sqmt

surfaces with two coats of enamel paint to give even shade Hundred Twenty

incl . Cleaning the surface from dust and other foreign Two & Paise

matter with sand paper incl. applying one coat of metal

primer etc complete .

54 1138.00 Sqmt Providing and laying rough chiselled dressed stone flooring 549.47 Rupees Five Sqmt

over 20mm average thick base of cement mortar 1:5 (1- Hundred Forty

Cement : 5-coarse sand) or L.M. 1:1.5 (1- Lime putty : 1.5 - Nine & Paise

Forty Seven Only

coarse sand) including pointing with cement mortar 1:2 (1-

cement : 2-stone dust) etc. complete. (A) 25mm thick

55 3060.00 Sqmt Providing and laying polished kota stone slab flooring over 1029.22 Rupees One Sqmt

20mm average thick base of cement mortar 1:6 (1-Cement Thousand

: 6-coarse sand) or L.M. 1:1.5 (1- Lime putty : 1.5 - coarse Twenty Nine &

sand) laid over and jointed with grey cement slurry mixed

with pigment to math the shade of slab including rubbing

and polishing etc. complete. (A) 30mm thick

56 94.00 Sqmt Providing and laying polished kota stone slab 25mm thick 1089.67 Rupees One Sqmt

in risers of steps, skirting Dado and pillars laid on1Omm Thousand Eighty

thick cement mortar 1:3 (1-Cement : 3 coarse sand) and Nine & Paise

Sixty Seven Only

jointed with grey cement slurry mixed with pigment to

match the shade of slab including rubbing and polishing

57 812.00 Sqmt P & L 24" x 24" vitrified 8 mm thick tile flooring over 20mm 1397.83 Rupees One Sqmt

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse Thousand Three

sand) on new surface or fixing on existing flooring by Hundred Ninty

adhesive material including dismantling of existing flooring

and jointed with colour cement slurry including finished with

flush pointing & cleaning the surface etc. complete for

antiskid / matt finish. Providing 3 to 5 mm grooves for

between the tiles and filling with epoxy material as per

engineer in charge.

58 930.00 Sqmt Providing & fixing Vitrified tiles 8 to 10 mm thick in skirting 1141.45 Rupees One Sqmt

risers of steps and dado on 10 mm thick cement plaster 1 : Thousand One

3 ( 1 cement : 3 coarse sand) and jointed with white cement Hundred Forty

Forty Five Only

59 371.00 Sqmt Providing and laying Granite stone slab flooring over 20 4045.05 Rupees Four Sqmt

mm. (average thick base of cement mortar 1:6 (1 cement : Thousand Forty

6 coarse sand ) and laid over and jointed with grey cement Five & Paise Five

slurry including rubbing and polishing complete. 18 mm

60 3.00 Sqmt Providing & Fixing Italian Marble inlay of colour of size 48518.38 Rupees Forty Sqmt

1200 mm x 1200 mm. Eight Thousand

Eighteen & Paise

Thirty Eight Only

61 602.00 Sqmt Providing and laying polished Granite Slab 18mm thick on 4509.65 Rupees Four Sqmt

walls cladding, window sill, jambs, urinal partition and pillars Thousand Five

laid 10mm thick Chemical of Endura or Equivalent and Hundred Nine &

Paise Sixty Five

jointed with Grey Cement Slurry including full moulded

round front, Side edges , rubbing and polishing etc. and

required bullet fastening required complete.

62 26.00 Sqmt Providing & laying sandwich type platform of 18 mm thick 4508.64 Rupees Four Sqmt

Granite / Kota stone of approved shade by Thousand Five

Architect/Consultant, top pattern stone of 18 mm thick Hundred Eight &

Paise Sixty Four

Granite of approved shade of approved shade and sample

on top and 25 mm thick kota in bottom with 30 mm thick

screed of (1:2:4) in between, with sandwich supports of

mm thick two kota on sides and screed in between and

mm raised platform with kota on top as per design with also

fixing granite stone on outsides facia of platform wherever

required etc. for all floors, levels & heights. The rate

includes cutting for sink, rounding, chamfering and mirror

polishing of edges & all facia with including necessary

bonding adhesive like araldite or equivalent etc. complete

with necessary requirements as directed by Engineer in

charge. Only plan area shall be measured and paid for, rate

shall be exclusive of SS sink, pillar tap, bib tap-coupling

63 667.00 Cum Providing and laying Trimix RMC mix cement concrete M- 5166.15 Rupees Five Cum

200 in roads / drive ways using coarse sand and graded Thousand One

stone aggregates 20 to 25 mm nominal size in appropriate Hundred Sixty

quantity as per specification, mechanically vibrated using

and surface screed vibrators, vacuum pump power floater,

power trowel, concrete floor cutter etc. Including approved

quality floor hardener @ 2 kg/smt on top surface incl. steel

form work with 200 mm M.S. channel sections incl. proper

curing and providing and filling construction joint and

dummy joints with "shalitax" primer silflex sheet not less

than 20 mm th. incl. rounding the edges and cutting the

groove by using concrete cutter in zigzag pattern upto 1/3

depth of the RCC thickness and not less than 10 mm in

width and filling the grooved by dummy joints with bitumen

sealing compound of grade-A Including making all

necessary arrangements for expansion joints at every

mtr's square or as per site situation with filling bitumen etc.

complete. Note :- This item will be excluded of

reinforcement but Including centering, shuttering, MS form

work, necessary tools & plants and all required materials

etc. comp. as directed by Engg. In charge.

64 2400.00 Sqmt Providing and fixing pre- cast Rubber Dye/ steel Dye 684.14 Rupees Six Sqmt

interlocking concrete block 60mm thick with grade of Hundred Eighty

concrete M300 pneumatic compressed/ vibrated Four & Paise

mechanically and as per approved design Confirming to IS

15658:2006 including 35mm Sand layer for levelling and

filling the joint with sand in proper line and level as per

guidelines of IRC : SP 63-2018 etc. Complete.

65 168.00 Sqmt Providing and laying rough chiselled dressed stone Strip 1237.25 Rupees One Sqmt

flooring over 20mm average thick base of cement mortar Thousand Two

1:5 (1-Cement : 5-coarse sand) or L.M. 1:1.5 (1- Lime putty Hundred Thirty

: 1.5 - coarse sand) including pointing with cement mortar

Twenty Five Only

1:2 (1-cement : 2-stone dust) etc. complete.

66 160.00 Sqmt Providing and laying ceramic tiles 6 mm thick in flooring 970.07 Rupees Nine Sqmt

treads of steps and landing laid on a bed of 12 mm thick Hundred Seventy

cement mortar 1 : 3 ( 1 cement : 3 coarse sand) finishing & Paise Seven

with flush pointing in white cement.

67 478.00 Sqmt TENSILE STRUCTURE: Supply, fabrication and erection of steel 5876.18 Rupees Five Sqmt

structure and membrane panels with steel cables and GI corner fittings Thousand Eight

nuts and bolts and associated accessories with membrane works. Hundred Seventy

Membrane system shall include membrane fabric, wire ropes and

cables, shackles, rigging screws, clamps and tensioning hardware. Rate

should be includes of cost of cable, corner fixture/ hardware, anchor bolt.

Entire work shall be carried out by approved vendors Sprech Tenso-

Structures/ Technospan Structure/Joy Architronics/ any other vendor

approved by Architect . The structural design & drawings shall be

provided by the contractor including Reaction forces drawings/details on

Pronet (TechNet Easy software 10.1) and steel analysis should be done

with Easy Beam and the steel members should be optimized with

DlubalR stab software version-7 or more which should be designed

/certified by a qualified Archineer in Membrane Structures from

National/International Institute. The cost includes supplying, designing,

fabricating, erecting of tubular structure including welding, scaffolding,

cost of primer, polyurethane paint application, vetting of design by third

party consultant, etc complete.

Tensile Fabric: Ferrari Precontraint 1002 T2 Fluotop PVDF coated PVC /

polyester Fabric. Weight 1050 gsm, Tensile Strength : 420/400

DaN/5cm, Tear resistance: 55/50 DaN. All outer fabric to be waterproof

type with 15 years warrantee. Boundary cables should be of GI as per

the design requirements. Corner fittings should be of epoxy primer

coating and PU hard to coats. All nuts should be HDG and bolts should

be (8.8 grade BS). Fabric welding should be high frequency heat

welding. The tubular structure system with plate connectors, pinion

joints, etc. is to be provided. Measurement: only plan area measured for

68 13.00 Sqmt Providing and fixing in position collapsible steel gate / 5899.26 Rupees Five Sqmt

shutters with vertical channels 20 x 10 x 2 mm braced with Thousand Eight

flat iron diagonals 20 x 5 mm size with top and bottom rails Hundred Ninty

of T Iron 40x 40 x 6 mm with 38mm dia, steel pulleys

Twenty Six Only

complete with bolts, nuts, locking arrangements, stoppers

handles including applying a priming coat of red lead paint.

69 48.00 Sqmt Providing & fixing M.S. sliding gate made from 75 mm x75 7971.93 Rupees Seven Sqmt

mm x 3 mm M. S. square pipe as frame and using 50 mm x Thousand Nine

50 mm x 3 mm M. S. square pipe fixing in diagonal shape Hundred Seventy

as per drawings & design and doing duco spray paint to M.

Ninty Three Only

S. gate sections complete as per Engineer in charge.

70 63.00 Sqmt Providing & Fixing M.S. Square railing using 50 mm dia 4559.14 Rupees Four Sqmt

round pipe as top members and 50 mm x 50 mm x 3 mm Thousand Five

vertical and horizontal members and using 25 mm x 25 mm Hundred Fifty

x 3 mm vertical members as per drawings & design

including doing duco paint work.

71 92.00 Sqmt Providing & Fixing M.S. Square railing using 50 mm dia 3484.50 Rupees Three Sqmt

square pipe 3 mm thick as top members and 25 mm x 25 Thousand Four

mm x 3 mm vertical and horizontal members @ 15 cm Hundred Eighty

distance and as per drawings & design including one coat

of metal primer.

72 2000.00 Kg Providing & fixing making cattle trap from 50 mm dia G. I. 174.73 Rupees One Kg

pipe B class and provide ISMB 150 making as support as Hundred Seventy

shown in the drawings Four & Paise

73 120.00 Sqmt Providing and fixing fibre cement wood substitute product 606.00 Rupees Six Sqmt

from portland cement, silica, sand and special cellulose Hundred Six

fibre with high standard process (autoclave process) with Only

natural look and attractive as per curve design with

necessary hardware complete.

74 713.00 Sqmt Providing and laying water proofing treatment on terrace 1062.52 Rupees One Sqmt

including applying neat cement slurry 2.75 kg/Sq.mt on Thousand Sixty

cement admixed with water proofing component after Two & Paise Fifty

cleaning the surface applying cement concrete with brick

bat 75mm to 100mm thick with 50% of C.M 1:5 admixed

with water proofing component over 20mm thick layer of

C.M 1:5 to required slope including ramming at junction of

wall and slab, after two days of proper curing applying a

second coat of cement slurry , and finally finished surface

with white cement slurry, at all height, after flooded with

terrace shall be finished with water for a period of two

week. complete.as directed by EIC/Architect.

75 713.00 Sqmt Providing and laying broken china mosaic flooring for 747.29 Rupees Seven Sqmt

terrace using 12 mm to 20 mm broken pieces of glazed Hundred Forty

tiles to be laid over cement mortar 1:3 to plain or slope and Seven & Paise

to be tempered to bring mortar creme out upto surface

using white cement including rounding off junctions and

extending them upto 15 cm along the wall, clearing with

water and oxalic acid etc. as directed.

76 4900.00 Sqmt Applying general insecticide pest control treatment to 68.48 Rupees Sixty Sqmt

floors, cupboards, plinth, walls etc. including labour material Eight & Paise

etc. complete. using heptachloride 20 EC. as per 6113-pest Forty Eight Only

concentration weight 0.50 percent is recommended one

litre chemical emulsion dilute with 39 litre of water will give,

total dilute concentration will be 40 litre inclusive of one litre

chemical emulsion application 0.5 / litre chemical / sqm of

surface is recommended as per IS standards.

77 38.00 Cum Filling with light material like Charu / Bauxite as directed 3275.43 Rupees Three Cum

including cement mortar Plaster 10 mm thick in CM. 1:3 in Thousand Two

all Around Surface (sides of Beams and top of sunk slab) Hundred Seventy

including adding water proofing material like SUNANDA,

Forty Three Only

FOSROK or PIDILITE to be used as a 0.15 Litre to

cement bag and making the surface clean and attractive as

design at any height, with all lead and lift up to height

metre etc. complete as directed by EIC.

78 233.00 Sqmt Providing and laying water proofing treatment in sunken 301.28 Rupees Three Sqmt

portion of WCs, bathroom etc., by applying cement slurry Hundred One &

mixed with water proofing cement compound consisting of Paise Twenty

applying:(a) First layer of slurry of cement @ 0.488 kg/sqm

mixed with water proofing cement compound @ 0.253 kg/

sqm. This layer will be allowed to air cure for 4 hours.(b)

Second layer of slurry of cement @ 0.242 kg/sqm mixed

with water proofing cement compound @ 0.126 kg/sqm.

This layer will be allowed to air cure for 4 hours followed

with water curing for 48 hours. The rate includes

preparation of surface, treatment and sealing of all joints,

corners, junctions of pipes and masonry with polymer

mixed slurry with all height.

79 219.00 Sqmt Providing and laying cement concrete flooring 1:2:4 (1- 276.79 Rupees Two Sqmt

cement: 2-coarse sand: 4-graded stone aggregate 20mm Hundred Seventy

nominal size) laid in one layer and finished with a floating Six & Paise

coat of neat cement. (A) 40mm thick.

80 70.00 Sqmt Providing and laying cement concrete flooring 1:2:4 (1- 322.93 Rupees Three Sqmt

cement: 2-coarse sand: 4-graded stone aggregate 20mm Hundred Twenty

nominal size) laid in one layer and finished with a floating Two & Paise

Ninty Three Only

coat of neat cement. (B) 50mm thick.

81 30.00 Rmt Providing & fixing speed breaker (Bump) making from PVC 1907.89 Rupees One Rmt

and rubber including fixing the block in anchor faster 4 nos. Thousand Nine

per block complete as per Engineer in charge. Hundred Seven

82 250.00 Rmt Providing and fixing pre-cast concrete kerb stone of grey 383.38 Rupees Three Rmt

cement based concrete block 30cm length,30cm height and Hundred Eighty

15cm thick of M200 grade concrete as per approved design Three & Paise

Thirty Eight Only

and including excavation for fixing in proper line and level,

filling the joint with C:M 1:3 (1cement: 3-fine sand) etc

83 150.00 No. Providing and fixing 1.2 thick S.S. 304 2b grade sheet with 2044.24 Rupees Two No.

nitric acid process etching plate and all text &graphics fill- Thousand Forty

up by standard enamel black coloured. Fitted with flats SS Four & Paise

etching plat should be mounted on wall / wooden surface

by SS screws and/or by 3m double side gum-tape, and

where applicable as per company's guideline, with prior

approval by Architect or on-site-authorised person. Indoor

signage: stainless steel etching signage size: 250x150mm

etc. complete with necessary requirements as directed by

84 20.00 No. Providing and fixing 1.2 thick S.S. 304 2b grade sheet with 19071.83 Rupees Ninteen No.

nitric acid process etching plate and all text &graphics fill- Thousand

up by standard enamel black coloured. Fitted with flats SS Seventy One &

etching plat should be mounted on wall / wooden surface

by SS screws and/or by 3m double side gum-tape, and

where applicable as per company's guideline, with prior

approval by Architect or on-site-authorised person. Indoor

signage: stainless steel etching signage size: 600x600mm

etc. complete with necessary requirements as directed by

85 1120.00 Kg Providing & fixing M. S. 100 mm x 100 mm x 3 mm pipe 205.35 Rupees Two Kg

including providing 200 mm x 200 mm x 6 mm M. S. plate 2 Hundred Five &

nos. bottom & top including fixing with anchor fastener Paise Thirty Five

including applying one coat of metal primer complete as per

Engineer in charge.

86 25.00 No. Providing & Fixing precast cement concrete benches with 40652.50 Rupees Forty No.

backrest and seating arrangement as per detail, of 1.8 mt, Thousand Six

length in C.C. 1:2:4 including necessary shuttering and Hundred Fifty

Two & Paise Fifty

fixing the same in C.C. 1:3:6 with required excavation etc.

complete as directed (Cost of excavation and P.C.C. shall

be paid separately.)

87 43.00 No. Providing and fixing bevelled edge mirror of superior glass 1010.00 Rupees One No.

mounted on 8 Mm thick A.C sheet or plywood sheet and Thousand Ten

fixed to wooden plugs with C.P brass screws and Only

washers.complete.as directed by EIC/Architect Size :

88 30.00 No. Providing and fixing Cast Iron steps of size 500 mm x 150 203.76 Rupees Two No.

mm x 22.5 mm and painting with two coats of anti corrosive Hundred Three &

paint etc. complete. Paise Seventy

89 4.00 No. Providing & Fixing C. I. Manhole cover with frame size 600 6767.00 Rupees Six No.

mm x 600 mm weight 38 kg including fixing the same, Thousand Seven

complete as per Engineer in charge. Hundred Sixty

90 2.00 No. Providing and fixing automatic boom barrier 6 mt wide gate 151500.00 Rupees One No.

including fixing the same as per engineer in charge. Lakh Fifty One

91 50.00 No. Providing & fixing concrete bollard 6" dia complete as per 2555.30 Rupees Two No.

Engineer-in-Charge. Thousand Five

92 1.00 No. Providing and installation of portable cabin of size and 353500.00 Rupees Three No.

future of cabin including with fan - 01, tube light 2, window Lakhs Fifty Three

with grill and canopy -02, main door with grill with canopy, 6- Thousand Five

amp switch socket - 02, AC provision with switch socket

lifting hook - 02, MCB box 01, Main switch board 01 etc.

complete with all labour material and transportation as per

instruction of Engineer in charge. Size 6' x 8' x 8'6”

93 93.85 Sqft Capital - Providing and fixing elevation feature JALI, 1027.93 Rupees One Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Thousand

50 mm for the locations as per the drawings. at all levels Twenty Seven &

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

94 427.18 Sqft Shaft- Providing and fixing elevation feature JALI, 548.23 Rupees Five Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Hundred Forty

50 mm for the locations as per the drawings. at all levels Eight & Paise

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

95 97.94 Sqft Base- Providing and fixing elevation feature JALI, 685.29 Rupees Six Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Hundred Eighty

50 mm for the locations as per the drawings. at all levels Five & Paise

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

96 99.90 Sqft Bracket- Providing and fixing elevation feature JALI, 1027.93 Rupees One Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Thousand

50 mm for the locations as per the drawings. at all levels Twenty Seven &

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

97 1248.62 Sqft Parapet daso- Providing and fixing elevation feature JALI, 513.97 Rupees Five Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Hundred Thirteen

50 mm for the locations as per the drawings. at all levels & Paise Ninty

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

98 229.27 Sqft Wall Moulding- Providing and fixing elevation feature JALI, 513.97 Rupees Five Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Hundred Thirteen

50 mm for the locations as per the drawings. at all levels & Paise Ninty

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

99 337.86 Sqft Capital- Providing and fixing elevation feature JALI, 753.81 Rupees Seven Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Hundred Fifty

50 mm for the locations as per the drawings. at all levels Three & Paise

Eighty One Only

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

100 1447.97 Sqft Shaft-Providing and fixing elevation feature JALI, 513.97 Rupees Five Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Hundred Thirteen

50 mm for the locations as per the drawings. at all levels & Paise Ninty

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

101 1204.40 Sqft Zarokha top shikher - Providing and fixing elevation feature 534.52 Rupees Five Sqft

JALI, JHAROKHA, MOULDING and CORNICES - 25 mm Hundred Thirty

thk. to 50 mm for the locations as per the drawings. at all Four & Paise

levels made from SWASTIKGRC make Glass fibre

reinforced concrete (GRC) using white cement, Quartz

Sand, AR Fibres, Water Plasticizers & COLOR in approved

shape, size and length as per the design and drawings and

as per specifications, mix design. The typical

SWASTIKGRC items should be of sizes as per the

drawings. Fixing of SWASTIKGRC items shall be with help

of S.S. Screws Fixtures, M.S Angle Cleats, Fissure Plug,

and Dowel Pin proper alignment as per drawings (Shop

drawings to be submitted by the contractor before the work

start). As per approved coating, paint, shade & Finishing

with SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

102 226.59 Sqft Capital Thambhli- Providing and fixing elevation feature 479.70 Rupees Four Sqft

JALI, JHAROKHA, MOULDING and CORNICES - 25 mm Hundred Seventy

thk. to 50 mm for the locations as per the drawings. at all Nine & Paise

levels made from SWASTIKGRC make Glass fibre

reinforced concrete (GRC) using white cement, Quartz

Sand, AR Fibres, Water Plasticizers & COLOR in approved

shape, size and length as per the design and drawings and

as per specifications, mix design. The typical

SWASTIKGRC items should be of sizes as per the

drawings. Fixing of SWASTIKGRC items shall be with help

of S.S. Screws Fixtures, M.S Angle Cleats, Fissure Plug,

and Dowel Pin proper alignment as per drawings (Shop

drawings to be submitted by the contractor before the work

start). As per approved coating, paint, shade & Finishing

with SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

103 579.19 Sqft Shaft , Base- Providing and fixing elevation feature JALI, 513.97 Rupees Five Sqft

JHAROKHA, MOULDING and CORNICES - 25 mm thk. to Hundred Thirteen

50 mm for the locations as per the drawings. at all levels & Paise Ninty

made from SWASTIKGRC make Glass fibre reinforced

concrete (GRC) using white cement, Quartz Sand, AR

Fibres, Water Plasticizers & COLOR in approved shape,

size and length as per the design and drawings and as per

specifications, mix design. The typical SWASTIKGRC items

should be of sizes as per the drawings. Fixing of

SWASTIKGRC items shall be with help of S.S. Screws

Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin

proper alignment as per drawings (Shop drawings to be

submitted by the contractor before the work start). As per

approved coating, paint, shade & Finishing with

SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

104 1127.50 Sqft Zarokha bottom- Providing and fixing elevation feature 513.97 Rupees Five Sqft

JALI, JHAROKHA, MOULDING and CORNICES - 25 mm Hundred Thirteen

thk. to 50 mm for the locations as per the drawings. at all & Paise Ninty

levels made from SWASTIKGRC make Glass fibre

reinforced concrete (GRC) using white cement, Quartz

Sand, AR Fibres, Water Plasticizers & COLOR in approved

shape, size and length as per the design and drawings and

as per specifications, mix design. The typical

SWASTIKGRC items should be of sizes as per the

drawings. Fixing of SWASTIKGRC items shall be with help

of S.S. Screws Fixtures, M.S Angle Cleats, Fissure Plug,

and Dowel Pin proper alignment as per drawings (Shop

drawings to be submitted by the contractor before the work

start). As per approved coating, paint, shade & Finishing

with SWASTIKGRC powder & filling the joints with Epoxy

sealant neatly between SWASTIKGRC items and primary

structures. The fins should be in absolute straight plumb

line and length and joins between channels should be

neatly filed to make seamless uniform surface across the

entire elevation of the building without any visibility to joints.

M.S. Fabrication, Scaffolding, Transportation, Labour, etc.

should be done by the Contractor as directed by AE.

105 1.00 No. Providing & Installation of fountain consist of 1: form bubble 308626.10 Rupees Three No.

nozzles - 8 Nos., Warm White Led light 18 watt / 12-volt S. Lakhs Eight

S. 304 - 8 nos., RGB controller and SMPS - 1 Nos. 1" Thousand Six

height adjusting valve UPVC - 8 nos., 2 HP submersible

Six & Paise Ten

pump klassic 1 nos. starter 1 nos. electrical wiring inside

the fountain tank conceal 1 nos. syntex bos 1 nos. UPVC

piping structure of fully fountain 1 nos. installation & labour

charges including transportation etc.

106 1.00 No. Providing & Supplying Gadu (bullock cart), Size Length-12' 87112.50 Rupees Eighty No.

Width-7' complete as per instruction of Engineer-in-Charge. Seven Thousand

107 1.00 No. Providing & Supplying Chabutro, Size Height-12' Diameter- 98727.50 Rupees Ninty No.

2'-6" complete as per instruction of Engineer in charge. Eight Thousand

Paise Fifty Only

108 1.00 No. Providing & supplying Pataro, Size: Height-3' width-2'-6" 46460.00 Rupees Forty Six No.

Length-5' complete as per instruction of Engineer in Thousand Four

charge. Hundred Sixty

109 1.00 No. Providing & supplying Ghanti, Size:Diameter-1'6" to 2' 9292.00 Rupees Nine No.

complete as per instruction of Engineer in charge. Thousand Two

110 1.00 No. Providing & Supplying Valonu, Size : Heigth-6' with mud pot 4646.00 Rupees Four No.

complete as per instruction of Engineer in charge. Thousand Six

111 1.00 No. Providing & Supplying Chaakdo (potter's wheel), Size : 17422.50 Rupees No.

Diameter-3' complete as per instruction of Engineer in Seventeen

charge. Thousand Four

Two & Paise Fifty

112 8.00 No. Providing & supplying Kothi big one piece, Size : Height-3'- 8130.50 Rupees Eight No.

6" Diameter-1'-6" complete as per instruction of Engineer in Thousand One

charge. Hundred Thirty &

Paise Fifty Only

113 48.00 No. Terracotta animals, Size: 1' to 3'. 2903.75 Rupees Two No.

Hundred Three &

114 1.00 No. Providing & supplying Metal Vessel, Weight: 8 KG 11034.25 Rupees Eleven No.

complete as per instruction of Engineer in charge. Thousand Thirty

Twenty Five Only

115 1.00 No. Providing & Supplying Metal Vessel, Weight : 3 KG 4646.00 Rupees Four No.

complete as per instruction of Engineer in charge. Thousand Six

116 1.00 No. Providing & Supplying Metal water Vessel complete as per 34845.00 Rupees Thirty No.

instruction of Engineer-in-charge. Four Thousand

Forty Five Only

117 1.00 No. Providing & Supplying Metal Vessel, Weight : 4.5 KG 6388.25 Rupees Six No.

complete as per instruction of Engineer in charge. Thousand Three

Twenty Five Only

118 1.00 No. Providing & Supplying Metal Vessel, Weight : 2.1 KG 4545.00 Rupees Four No.

complete as per instruction of Engineer in charge. Thousand Five

119 1.00 No. Providing & Supplying Metal Vessel, Weight : 16KG 3232.00 Rupees Three No.

complete as per instruction of Engineer in charge. Thousand Two

120 1.00 No. Providing & Supplying Metal Vessel, Weight : 16KG 23230.00 Rupees Twenty No.

complete as per instruction of Engineer in charge. Three Thousand

121 1.00 No. Providing & Supplying Metal Vessel, Weight : 10 KG 13938.00 Rupees Thirteen No.

complete as per instruction of Engineer in charge. Thousand Nine

122 1.00 No. Providing & Supplying Metal Vessel, Weight : 38 KG 75497.50 Rupees Seventy No.

complete as per instruction of Engineer in charge. Five Thousand

Paise Fifty Only

123 1.00 No. Providing & Supplying Charu (Metal Vessel), Size : Height- 46460.00 Rupees Forty Six No.

3' Diameter-2'-25 KG complete as per instruction of Thousand Four

Engineer in charge. Hundred Sixty

124 1.00 No. Providing & Supplying Stone kathrot complete as per 2651.25 Rupees Two No.

instruction of Engineer in charge. Thousand Six

Twenty Five Only

125 1.00 No. Providing & supplying DABDO, SIZE : Height-3’ Width-2’-6” 45450.00 Rupees Forty No.

Length-5’ complete as per instruction of Engineer in Five Thousand

charge. Four Hundred

126 5.00 No. Providing & making, Fixing Stainless steel letters 12" height 98727.50 Rupees Ninty No.

with led light behind the ACP board complete as per Eight Thousand

instruction of Engineer in charge. (English letter - Urban Seven Hundred

Paise Fifty Only

127 1.00 No. Providing and fixing Kitchen sink with C.I. or M.S. brackets, 2280.27 Rupees Two No.

painted white including cutting holes in walls and making Thousand Two

good the same but excluding fittings. (C) Vitreous China Hundred Eighty &

Sink.(i) 600mm x 450mm x 150mm size

128 50.00 No. Providing and fixing wash down water closet (European 3595.23 Rupees Three No.

type, W.C. Pan) with integral P or S trap including jointing Thousand Five

the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1- Hundred Ninty

fine sand) (Seal and cover to be measured and paid for

separately)(A) vitreous China Pattern :(i) in white colour,

plastic seat and cover for wash down water closer with C.P.

brass hinges and rubber buffers. (B) Black plastic seal and

cover., chromium plated brass half turn flush cock of

approved quality including fixing in pipe line etc.

complete.(iii) 32mm dia., Providing and fixing toilet paper

holder.(A) C.P. Brass.

129 43.00 No. Providing and fixing washbasin with single hole for pillar tap 3817.28 Rupees Three No.

with C.I. or M.S. brackets painted white including cutting Thousand Eight

holes and making good the same but including fitting (A) Hundred

Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm

size. (i) In white colour., pillar tap, capstan head, screw

down high pressure with screws, shanks and back nuts. (ii)

20mm dia., C.P. brass waste for washbasin or sink. (B)

40mm dia., M.I.. fisher union for washbasin or sink. (B)

130 44.00 No. Providing and fixing chromium plated, bottle trap with 295.80 Rupees Two No.

necessary couplings of approved quality for wash basin. Hundred Ninty

131 44.00 No. Supply, checking, storing & fixing C.P. brass angle valve for 1467.53 Rupees One No.

basin & Sink MODEL:JAQUAR-ALI-85053, of approved Thousand Four

quality conforming to IS:8931 for a) 15mm Nominal Bore Hundred Sixty

(Final Model of fixture to be selected by architect)

Fifty Three Only

132 10.00 No. Supply, checking, storing & fixing C.P. brass bib cock 2104.84 Rupees Two No.

MODEL:JAQUAR-ALI-85037 of approved quality Thousand One

conforming to IS:8931.(Final Model of fixture to be selected Hundred Four &

by architect)a) 15mm Nominal Bore

133 22.00 No. Providing and fixing Urinal of approved quality including 2348.25 Rupees Two No.

connection with trap and with integral longitudinal flush Thousand Three

pipe.(A)Squatting plate pattern white earthenware 550mm x Hundred Forty

300mm. with chromium plated, bottle trap with necessary

Twenty Five Only

couplings of approved quality.20mm dia.,C.P. brass waste.

Chromium plated brass half turn flush cock of approved

quality including fixing in pipe line etc. complete.(i) 20mm

134 90.00 No. Supply, checking, storing & fixing of Heavy class S.S. 1379.66 Rupees One No.

Grating Model No. Chilly-CCT-SFC-127 or Equivalent with Thousand Three

Mosquito /Cockroach proof S.S. strainer of approved Hundred Seventy

design by Interior including setting in floor with cement

motor to match with floor finish as per architect requirement

suitable for FD (Floor drain) and FT (Floor trap). Note : Size

of trap is vary as per final Product Selection.

135 4.00 No. Providing and Fixing Handicap Toilet set including EWC, 40693.91 Rupees Forty No.

Cistern, Seat Cover, Fittings, Washbasin,, Hinged Rail, Thousand Six

Grab Bar and Faucet with Spatula Lever including Cast Iron Hundred Ninty

chair backed and necessary bolts and nuts complete,

including painting of fittings and brackets, cutting and

making good the walls and floors wherever required as per

technical specifications, provided drawings by architect,

technical specification and as directed by the authority EIC.

including Toilet Set(Jaquar - CNSWHT-755S220SPPZ)+

Wash Basin(CNS-WHT-811) and Grab Bar(WAC-WHT-

BG0800 & WAC-WHC-BR0600) as directed by EIC. (Make:

Jaquar/Cera/Hindware)

136 54.00 No. Supply, checking, storing & fixing C.P. brass Health faucet 1498.84 Rupees One No.

MODEL:JAQUAR-ALD-557, of approved quality with Thousand Four

holder.(Final Model of fixture to be selected by EIC) Hundred Ninty

Eighty Four Only

137 14.00 No. Supply, checking, storing & fixing CP Over Head shower 9484.91 Rupees Nine No.

MODEL:JAQUAR OHS-CHR-1663,CP single lever wall Thousand Four

mixer FUS-CHR-29065MK with Concealed body Shower Hundred Eighty

Valve MODEL:JAQUAR ARC-CHR-87233C and bath spout

complete as per instructions of the engineer-in-charge.

138 198.00 Rmt Providing and fixing PVC Agri 6Kg/cm2 and fitting for SOIL 173.72 Rupees One Rmt

& WASTE water discharge, including all fittings with and Hundred Seventy

with out inspection doors, including supports brackets as Three & Paise

per supplier specification and distance, cutting,

chases/holes in walls/floors/slab etc. (Pipes to laid in Toilets

(Make: Astral, Ashirvad, Supreme) 50mm

139 84.00 Rmt Providing and fixing PVC SWR Pipe confirming to IS 383.80 Rupees Three Rmt

13592-92 TYPE B and fitting as per IS 14735-99 for SOIL Hundred Eighty

& WASTE water discharge, including all fittings with and Three & Paise

with out inspection doors, including supports brackets as

per supplier specification and distance, cutting, chases

/holes in walls/floors/slab etc. (Pipes to laid in

Toilets)(Make: Astral, Ashirvad, Supreme). 75 mm

140 288.00 Rmt Providing, laying and jointing in true line and level 110 835.15 Rupees Eight Rmt

diameter U.P.V.C (Type B) conforming to IS 13592-1992 Hundred Thirty

with one end plain and other end socketed with rubber ring, Five & Paise

& fittings conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diameter x 149 mm

length x 145 mm height at every 2000 mm centre to centre

or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

141 160.00 Rmt Providing, laying and jointing in true line and level 160 831.22 Rupees Eight Rmt

diameter U.P.V.C (Type B) conforming to IS 13592-1992 Hundred Thirty

with one end plain and other end socketed with rubber ring, One & Paise

Twenty Two Only

& fittings conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 160 mm diameter x 210 mm

length x 196 mm height at every 2000 mm centre to centre

or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

142 90.00 No. Providing and fixing PVC SWR Nahni trap IS 14735 for 571.08 Rupees Five No.

drain - 100 mm diameter with jali of the following nominal Hundred Seventy

diameter of self cleansing design with C.I screed down or One & Paise

hinged grating including the cost of cutting and making

good the walls.

143 420.00 Rmt Providing and fixing concealed centre point to wall ceiling & 205.00 Rupees Two Rmt

floor CPVC (SDR 13.5) PIPE having National Sanitation Hundred Five

Foundation (NSF) seal for potable water of following dia. Only

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete.(B)20 mm

144 88.00 Rmt Providing and fixing concealed centre point to wall ceiling & 249.72 Rupees Two Rmt

floor CPVC (SDR 13.5) PIPE having National Sanitation Hundred Forty

Foundation (NSF) seal for potable water of following dia. Nine & Paise

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete.(C) 25mm

145 48.00 Rmt Providing and fixing concealed centre point to wall ceiling & 333.66 Rupees Three Rmt

floor CPVC (SDR 13.5) PIPE having National Sanitation Hundred Thirty

Foundation (NSF) seal for potable water of following dia. Three & Paise

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete.(D) 32mm

146 228.00 Rmt Providing laying and jointing in true line and level 25mm 91.84 Rupees Ninty Rmt

dia. U.P.V.C. Pipe (SCH-40)for cold water including fittings One & Paise

make PRINCE/SUPREME/ASTRAL/FINOLEX or equivalent Eighty Four Only

as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or

shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

147 178.00 Rmt Providing laying and jointing in true line and level 32mm 119.15 Rupees One Rmt

dia. U.P.V.C. Pipe (SCH-40)for cold water including fittings Hundred Ninteen

make PRINCE/SUPREME/ASTRAL/FINOLEX or equivalent & Paise Fifteen

as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or

shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

148 128.00 Rmt Providing laying and jointing in true line and level 40mm 148.12 Rupees One Rmt

dia. U.P.V.C. Pipe (SCH-40)for cold water including fittings Hundred Forty

make PRINCE/SUPREME/ASTRAL/FINOLEX or equivalent Eight & Paise

as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or

shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

149 55.00 Rmt Providing laying and jointing in true line and level 50mm 195.67 Rupees One Rmt

dia. U.P.V.C. Pipe (SCH-40)for cold water including fittings Hundred Ninty

make PRINCE/SUPREME/ASTRAL/FINOLEX or equivalent Five & Paise

Sixty Seven Only

as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or

shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

150 90.00 Rmt Providing, fixing, jointing and testing in position the 788.81 Rupees Seven Rmt

following U-PVC pressure threaded Pipes as per ASTM D Hundred Eighty

1785 Schedule 80 and threaded conforming to IS:554. Cut Eight & Paise

Eighty One Only

to required lengths including all necessary fittings and

specials such as bends, tees, unions, reducers, flanges

and plugs etc. The pipes & fittings shall be tested to a

pressure of 15 Kg/Sq.cm. Fixing at wall/ ceiling level

supported by clamps, fastener, hangers etc. as per

specification. Cutting hole in wall / floor slab and making

good the same with cement concrete 1:2:4 complete as

required. GI heavy class pipe sleeve of larger diameter

shall be provided wherever the pipes crossing the

walls/floor slab and sealing the sleeves as per

consultants requirement. Threading, jointing & making

proper connections & as per provided drawings by

architect, techincal specification and as directed by the

authority EIC.(Water Supply Riser & Main Ring) (make:

Astral, Ashirvad & supreme) 65mm dia

151 3.00 No. Providing and fixing forged brass lever operated ball valve 1736.19 Rupees One No.

of full flow with forged brass ball (Machined to mirror Thousand Seven

smooth finish with hard chrome plated) and spindle with Hundred Thirty

setting and gland of superior quality having minimum

working pressure of 16 kg/cm2 etc. complete in all

respect.(Make: Sant, Zoloto, leader) 32mm dia

152 4.00 No. Providing and fixing forged brass lever operated ball valve 2473.49 Rupees Two No.

of full flow with forged brass ball (Machined to mirror Thousand Four

smooth finish with hard chrome plated) and spindle with Hundred Seventy

setting and gland of superior quality having minimum

Forty Nine Only

working pressure of 16 kg/cm2 etc. complete in all

respect.(Make: Sant, Zoloto, leader) 40mm dia

153 6.00 No. Providing and fixing forged brass lever operated ball valve 3786.49 Rupees Three No.

of full flow with forged brass ball (Machined to mirror Thousand Seven

smooth finish with hard chrome plated) and spindle with Hundred Eighty

Six & Paise Forty

setting and gland of superior quality having minimum

working pressure of 16 kg/cm2 etc. complete in all

respect.(Make: Sant, Zoloto, leader) 50mm dia

154 3.00 No. Supplying, fixing, testing and commissioning of following 3066.36 Rupees Three No.

valves, gauges and strainers for condenser water Thousand Sixty

circulation as per specifications.(Make: Sant, Zoloto, Six & Paise

Thirty Six Only

leader) BUTTERFLY VALVE (MANUAL) with C I body SS

disc nitrile sheet & O - ring & PN 16 pressure rating as

specified. 65 mm dia.

155 205.00 Rmt Providing and Laying Underground drainage System Foam 1416.02 Rupees One Rmt

Core SN8 pipe complete with all fittings excavation of Thousand Four

trench 0.7m wide and depth varying from 0.75m to 2.4m, Hundred Sixteen

and refilling the same after laying of drain and concrete

encasement in concrete 1:3:6 grade concrete with

minimum thickness of encasement 100mm thk & as per

provided drawings by architect, technical specification and

as directed by the authority EIC.(Make: Supreme, Astral or

equivalent ) 150 mm dia

156 115.00 Rmt Providing and Laying Underground drainage System Foam 2159.38 Rupees Two Rmt

Core SN8 pipe complete with all fittings excavation of Thousand One

trench 0.7m wide and depth varying from 0.75m to 2.4m, Hundred Fifty

and refilling the same after laying of drain and concrete

Thirty Eight Only

encasement in concrete 1:3:6 grade concrete with

minimum thickness of encasement 100m thk & as per

provided drawings by architect, technical specification and

as directed by the authority EIC.(Make: Supreme, Astral or

equivalent ) 200 mm dia

157 25.00 No. Providing and fixing S.W. gully trap with C.I. grating brick 1246.92 Rupees One No.

masonry chamber and water tight C.I. cover with frame of Thousand Two

300mm x 300mm size (inside) with standard weight.(i) Hundred Forty

Six & Paise Ninty

Square mouth traps.(B) 150mm x 100mm size P or R type

158 16.00 No. Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- 11029.97 Rupees Eleven No.

cement :2-coarse sand : 4-graded stone aggregate 20mm Thousand

nominal size) foundation concrete 1:3:6 mix (1-cement : 3- Twenty Nine &

coarse sand :6- Brick bats 40 + 50mm size) inside

plastering 15mm thick with Cement Mortar 1:3 (1-Cement :

3-coarse sand) finished with a floating coat of neat cement

and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4- stone aggregate 20mm

nominal size) finished smooth complete including curing

and testing (i) Inside size 900mm x 1200mm and 1.5M.

deep including C.I. cover with frame size 560mm diameter

total weight of cover and frame to be not less than 128 kgs.

(Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With

230mm thick walls of brick masonry using brick having

crushing strength not less than 35Kg. / Sq.cm. in Cement

Mortar 1:5 (1- Cement: 5- Coarse sand) (1) A type depth

0.90 Metre for 150mm diameter sewer.

159 5.00 No. Extra rate for constructing B.B masonry for every additional 522.96 Rupees Five No.

depth 0.10 meter or part thereof over item 24.27 (I) for Hundred Twenty

depth from 0.90 meter to 1.50 meter. Two & Paise

160 10.00 No. Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- 19330.46 Rupees Ninteen No.

cement :2-coarse sand : 4-graded stone aggregate 20mm Thousand Three

nominal size) foundation concrete 1:3:6 mix (1-cement : 3- Hundred Thirty &

Paise Forty Six

coarse sand :6- Brick bats 40 + 50mm size) inside

plastering 15mm thick with Cement Mortar 1:3 (1-Cement :

3-coarse sand) finished with a floating coat of neat cement

and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4- stone aggregate 20mm

nominal size) finished smooth complete including curing

and testing (i) Inside size 900mm x 1200mm and 1.5M.

deep including C.I. cover with frame size 560mm diameter

total weight of cover and frame to be not less than 128 kgs.

(Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With

230mm thick walls of brick masonry using brick having

crushing strength not less than 35Kg. / Sq.cm. in Cement

Mortar 1:5 (1- Cement: 5- Coarse sand) (2) B type depth

150mm diameter sewer.

161 18.00 No. Extra rate for constructing B.B masonry for every additional 397.19 Rupees Three No.

depth 0.10 meter or part thereof over item 24.27 (II) for Hundred Ninty

depth from 1.50 meter to 2.25 meter. Seven & Paise

162 10.00 No. Constructing brick masonry chamber for underground C.I. 2932.93 Rupees Two No.

Inspection chamber and bends with bricks having crushing Thousand Nine

strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover Hundred Thirty

with frame (Light duty) 455mm x 610mm internal

Ninty Three Only

dimensions total weight of cover with frame to be not less

than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. )

(R.C.C. top slab with 1:2:4 mix (1-cement :2- coarse sand

:4-graded stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on walls

and bed concrete etc. complete.(i) Inside dimensions

455mmx 610mm and 450mm deep for single pipe line.

163 150.00 Rmt Drilling pilot borehole of size 250/300 mm at above site by 756.49 Rupees Seven Rmt

mud flush direct rotary rig. Depth up to 300mtr. Hundred Fifty Six

164 150.00 Rmt Reaming of 250/300 mm dia. Pilot borehole to size 550 mm 465.61 Rupees Four Rmt

dia. Including assembling, lowering housing, casing strainer Hundred Sixty

pipers with gravel packing and clay ball packing etc Depth Five & Paise

165 150.00 Rmt Supply of M.S. E.R.W. plain end medium duty pipe 3605.70 Rupees Three Rmt

confirming to IS 4270/2001 with latest amendments in Thousand Six

random length of 4 to 7 mtr. of size 250 mm dia (minimum Hundred Five &

thickness of 7.1 mm)

166 200.00 Slots Screen Slotting of ERW pipe with minimum size of slot 6.75 0.26 Paise Twenty Six Slots

cm x 6.35 cm x 1.59 mm (1/16") for 250 mm dia pipe. Only

167 150.00 Rmt Providing, fixing, jointing and testing in position the 1051.41 Rupees One Rmt

following U-PVC pressure threaded Pipes as per ASTM D Thousand Fifty

1785 Schedule 80 and threaded conforming to IS:554. Cut One & Paise

to required lengths including all necessary fittings and

specials such as bends, tees, unions, reducers, flanges

and plugs etc. The pipes & fittings shall be tested to a

pressure of 15 Kg/Sq.cm. Fixing at wall/ ceiling level

supported by clamps, fastener, hangers etc. as per

specification. Cutting hole in wall / floor slab and making

good the same with cement concrete 1:2:4 complete as

required. GI heavy class pipe sleeve of larger diameter

shall be provided wherever the pipes crossing the

walls/floor slab and sealing the sleeves as per

consultants requirement. Threading, jointing & making

proper connections & as per provided drawings by

architect, techincal specification and as directed by the

authority EIC.(Water Supply Riser & Main Ring) (make:

Astral, Ashirvad & supreme) 80mm dia

168 25000.00 Lit Providing erecting and fixing double coated ISI water tank 4.66 Rupees Four & Lit

of required capacity each with all necessary fittings and Paise Sixty Six

connection etc. complete on terrace. Only

169 6.00 No. PERCOLATION WELL-Furaat Horizontal Filtration Module 64316.80 Rupees Sixty No.

(HFM-2350) of diameter 1500mm and 2350mm height. In a Four Thousand

typical Horizontal Filtration Module (HFM-2350) each Three Hundred

Sixteen & Paise

vertical precast slab has eight inlets of 60 mm diameter

each. Top module is above ground level with an option of

keeping height 300 /400/ 610 mm above ground level. Top

module accommodates filter media in the form of layers of

gravel supported on a pair of an open able perforated pre

cast slab ( 1075mm x 550mmx 40mm thick),. Bottom

module is for sedimentation. The inlet and outlet of the

system is 160mm diameter UPVC pipes. The entire system

contains approximately 0.08 cubic meter gravels of 40 mm

size. All precast concrete slabs are of M-25 grade. Filtration

capacity & testing up to 30m3 per hour from modular

systems only. This module is used for Roof/Surface water

and the filtered water to get into is finally connected with

the Sand Filtration Module. with excavation, filling etc

complete as per drawings/Architect/EIC.

170 551.00 Rmt Providing and fixing thermdrain grating, moulded jointless 2958.29 Rupees Two Rmt

inter woven construction 450mm width x 600 mm depth Thousand Nine

with both side brick masonry and bottom finish with Hundred Fifty

concrete channel including providing thermodrain 40 mm

thick cover as shown in the drawings & design.

171 48.00 Cum Providing and laying controlled cement concrete M.250 and 5379.26 Rupees Five Cum

curing complete including the cost of formwork and Thousand Three

reinforcement for reinforced concrete work in (A) Hundred Seventy

Foundations, footings, Base of columns and Mass

Twenty Six Only

A) M25-For Foundation

172 39.00 Cum Providing and laying controlled cement concrete M.250 and 8032.53 Rupees Eight Cum

curing complete including the cost of formwork and Thousand Thirty

reinforcement for reinforced concrete work in (D) Columns, Two & Paise Fifty

Pillars posts and struts, upto floor two level.

A) M25 - For Column

173 51.00 Cum Providing and laying controlled cement concrete M.250 and 6221.60 Rupees Six Cum

curing complete including the cost of formwork and Thousand Two

reinforcement for reinforced concrete work in (C) labs, Hundred Twenty

landing, shelves, Balconies, Lintels, Beams, Girders and

Cantilever upto floor two level.

A) M25 - For Beams

174 2555.00 Sqmt 20mm thick sand faced / Mala cement plaster on walls upto 369.94 Rupees Three Sqmt

height 10 metres above ground level consisting of 12mm Hundred Sixty

thick backing coat of C.M. 1:3 (1-cement : 3-sand) and Nine & Paise

Ninty Four Only

8mm thick finishing coat (A) Extra over items 58 to 67 for

providing and mixing water proofing materials in cement

in proportion recommended by the manufacturer.

175 48.00 Sqmt Providing & applying on Wall exterior/ interior Surface 814.06 Rupees Eight Sqmt

texture granules finish of Bakelite Hvlam Limited (No.21- Hundred

trowelled over 20mm thick Mala finished / sand faced

cement plastered (Two coat of 12mm in CM 1:3 & 8mm

coat in CM:1:1) sub strata to get an average finish coat

thickness of 0.08 to 1.2mm comprising of three

components viz Dry granules, Granules bonding agents

and top coat of glossy finish ( Dry granules shell be made

from silica sand pigments, chiefly inorganic) homopolymer

emulsion mix etc. of Bakelite hylam product etc. and top

coat made from solvent based acrylic polymer of Bakelite

hylam product including scaffolding. Including providing

necessary grooves in surface as per instruction in charge.

Upto 10m Height.

176 2555.00 Sqmt Finishing wall with water proofing cement paint of on wall 64.17 Rupees Sixty Sqmt

surfaces (Two coats) to give an approved brand and Four & Paise

manufacture and of required shape even shade after Seventeen Only

thoroughly brushing the surface to remove all dirt and

remains of loose powered materials. Extra over Item 51 for

every subsequent coat of water proofing cement paint of

approved brand and manufacture. Extra over item 51 for

finishing with cement paint on ceiling and sloping roofs.

177 35.00 Sqmt Providing and fixing of MS grill work at top of compound 1515.00 Rupees One Sqmt

wall design as per the architect drawing with fixing and Thousand Five

welding of all member and fixed with GI chain-link jali with Hundred Fifteen

apply primer and epoxy paint with final finishing

178 61.00 Sqmt Providing & fixing Mangalore clay tiles having designed size 1209.98 Rupees One Sqmt

20 cm x 30 cm on M.S. framing work over that providing & Thousand Two

fixing MDF sheet exterior grade of 12 mm thickness on Hundred Nine &

Paise Ninty Eight

M.S. frame structure over that providing half round

terracotta tiles size 18 cm x 13 cm fixing with chemical or

adhesive materials complete as per drawings & as per

instruction of Engineer in charge.

179 1875.00 Kg Providing & supplying fabricating entrance gate roof from 174.73 Rupees One Kg

various types of m. s. square pipes of 10 gauge as per Hundred Seventy

drawings including providing & fixing 16 mm square bar to Four & Paise

support bottom tiles as per drawing including providing one

coat of metal primer & two coat of enamel paint as directed

Engineering in charge.

180 1.00 No. Supply, installation, testing and commissioning of 2280 424200.00 Rupees Four No.

LPM @ 75m Head Main diesel engine driven horizontal Lakhs Twenty

centrifugal end suction top discharge pump set as per IS Four Thousand

:12469 specification with bronze impeller, EN8 shaft and

SS410 shaft sleeve coupled with diesel engine heat

exchanger cooled provided on common base plate

including exhaust piping, muffler, silencer, fuel tank with

diesel for testing as well for future storage (fuel storage

capacity shall be kept in order to run the pump at least for

hrs for ordinary hazard and 3hrs for high hazard), diesel

engine controller, battery with battery charger and stands,

coupling guard, foundation bolts etc.as per the statutory

181 1.00 No. Supply, installing, testing, & commissioning of Electric 257550.00 Rupees Two No.

motor driven Main Pump suitable for automatic operation Lakhs Fifty

consisting of the following (as per specification for External Seven Thousand

+ Internal hydrant system). Back Pull out centrifugal type

pump complete for delivery of 2280 LPM against a total

head of 75 metres with bronze impeller, shaft SS complete

with mechanical seal with Complete accessories like

Earthing, Local Push Button, Cabling between Panel and

Pump Motor. Including Squirrel cage induction motor.

Conforming to requirements of I.S.

182 1.00 No. Supply, installing, testing, & commissioning of electric 60600.00 Rupees Sixty No.

motor driven Jockey Pump suitable for automatic operation Thousand Six

consisting of the following (as per specification). Electric Hundred Only

driven automatic pressurisation pump set consisting of the

following. Vertical In line, centrifugal Multistage Jockey

pump complete for delivery of 180 LPM against a total head

of 60 metres with SS impeller complete with mechanical

seal with Complete accessories. Squirrel cage induction

motor suitable for above pump.2

183 3.00 No. Supplying, installing and commissioning of Bourdon type 2272.50 Rupees Two No.

Pressure gauge (150mm dial) with gauge cock - range 0-25 Thousand Two

kg/sq.cm(g). Hundred Seventy

Two & Paise Fifty

184 3.00 No. Supplying, installing and commissioning of Pressure switch 2499.75 Rupees Two No.

(2SPDT) with needle valve. Thousand Four

185 10.00 Rmt Supplying, installing and commissioning of Exhaust pipe - 2575.50 Rupees Two Rmt

150 mm dia M.S. 'B' class pipe with Rockwool insulation & Thousand Five

24SWG aluminium sheet cladding. Including MS supports Hundred Seventy

Five & Paise Fifty

186 5.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 4040.00 Rupees Four Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Thousand Forty

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Only

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

MS steel structural members.10 % of all the welded joints

shall be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

up etc. Painting for piping, fittings, hanger support with U

clamp, U bolt, threaded rods, nut, bots & washers &

structural pipe support shall be one coat of zinc primer and

two coats of fire red enamel paint Shade No.536 of IS 5:

1994 complete with all accessories as per approved

drawings, specification and direction of the Engineer-in-

Charge. Rate shall include supply and fixing of all MS

supports. 200mm nominal dia

187 2.00 No. Supplying, installing and commissioning of Cast iron double 19644.50 Rupees Ninteen No.

flanged Sluice Valve conf. to IS: 14846, PN-16 with fittings, Thousand Six

nut, bolts & washers, flanges etc. 200mm nominal dia Hundred Forty

188 1.00 No. Supplying, installing and commissioning of Cast iron double 18180.00 Rupees Eighteen No.

flanged Sluice Valve conf. to IS: 14846, PN-16 with fittings, Thousand One

nut, bolts & washers, flanges etc. 100mm nominal dia Hundred Eighty

189 11.00 No. Supplying, installing and commissioning of Cast iron wafer 7070.00 Rupees Seven No.

type lever operated butterfly valve conf. to IS: 13095, PN- Thousand

16 with fittings, flanges, nut, bolts & washers, etc. MOC of Seventy Only

the Body & disc shall be CI as per IS:210 FG200, EPDM /

Neoprene seat, carbon steel (EN8) shaft and nylon / Teflon

bearing. Valves exceeding 150 mm dia shall be gear

operated. 150mm nominal dia

190 2.00 No. Supplying, installing and commissioning of Dual plate 10605.00 Rupees Ten No.

Wafer type Non Return valve with PN 16 rating, fittings, Thousand Six

flanges, nuts, bolts, washers etc. 150 mm nominal dia. Hundred Five

191 1.00 No. Supplying, installing and commissioning of Dual plate 5933.75 Rupees Five No.

Wafer type Non Return valve with PN 16 rating, fittings, Thousand Nine

flanges, nuts, bolts, washers etc. 80 mm nominal dia Hundred Thirty

192 2.00 No. Supplying, installing and commissioning C.I. Y type Strainer 32320.00 Rupees Thirty No.

with suitable flanges, nuts, bolts, gaskets etc. complete. Two Thousand

200 mm nominal dia Three Hundred

193 1.00 No. Supplying, installing and commissioning C.I. Y type Strainer 23007.80 Rupees Twenty No.

with suitable flanges, nuts, bolts, gaskets etc. complete. Three Thousand

100 mm nominal dia Seven & Paise

194 1.00 No. Providing, fixing, testing and commissioning of air-cushion 42420.00 Rupees Forty No.

tank (air vessel) 350mm dia. & 1500mm high with dished Two Thousand

top, made of 8 mm thick M.S. sheet and 10 mm thick Four Hundred

dished ends with 25mm dia. brass air release valve (ball

195 1.00 No. Fabricating & Supply, installing, testing and commissioning 146450.00 Rupees One No.

of Control Panel with Cabling & Cable tray for Fire pumps. Lakh Forty Six

196 2.00 No. Supply, installation, testing & commissioning of Flexible 13130.00 Rupees Thirteen No.

connections for pumps 200mm Dia Thousand One

197 2.00 No. Supply, installation, testing & commissioning of Flexible 9595.00 Rupees Nine No.

connections for pumps 150mm Dia Thousand Five

198 1.00 No. Supply, installation, testing & commissioning of Flexible 6060.00 Rupees Six No.

connections for pumps 100mm Dia Thousand Sixty

199 1.00 No. Supply, installation, testing & commissioning of Flexible 4848.00 Rupees Four No.

connections for pumps 80mm Dia Thousand Eight

200 725.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 2878.50 Rupees Two Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Thousand Eight

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Hundred Seventy

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members.10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 150mm nominal dia

201 55.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 1666.50 Rupees One Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Thousand Six

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Hundred Sixty

Six & Paise Fifty

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members.10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 80mm nominal dia

202 125.00 Rmt Providing, laying, jointing and testing in excavated trenches 3413.80 Rupees Three Rmt

the following sizes of ductile iron K-9 class, 6.8mm Thousand Four

thickness pipes (6mtr per length) with accessories like Hundred Thirteen

fittings including tees, elbows, reducers, flanges, rubber

gaskets, G.I. nuts, bolts and washers including excavation

in all kind of soil, refilling, ramming, shoring, removing the

excavated surplus material, providing adequate support to

the pipe and making good the same complete as required.

Rate shall include for dewatering necessary to execute the

work. The pipe shall not be less than 1.0 m below ground

level at any point. For Underground Piping, excavation and

refilling will be paid separately 150mm nominal dia

203 125.00 Rmt Wrapping & Coating of Underground Pipe with pypcoat 757.50 Rupees Seven Rmt

tape by thermo fusion process and surface preparation by Hundred Fifty

applying cold primer (bitumen) 150mm nominal dia Seven & Paise

204 15.00 No. Supplying, installing, testing and commissioning of External 4545.00 Rupees Seven No.

yard hydrant comprising of the following, External Single Hundred Fifty

headed hydrant valve as per IS 5290, made of Stainless Seven & Paise

Steel(SS 304) with 63 mm dia instantaneous out & 80 mm

dia flanged inlet, Blank cap , chain and hand wheel etc

205 20.00 No. Supplying, installing, testing and commissioning of Internal 5050.00 Rupees Five No.

hydrant comprising of the following, Single headed hydrant Thousand Fifty

valve as per IS 5290, made of Stainless Steel(SS 304) with Only

63 mm dia instantaneous out & 80 mm dia flanged inlet

stand pipe included inlet, Blank cap, chain and hand wheel

206 35.00 No. 2 lengths of 15 Mtr long, 63mm dia RRL hose as per IS:636 13736.00 Rupees Thirteen No.

Type B with instantaneous couplings and Hoses shall be Thousand Seven

stored inside the hose cabinet. Hundred Thirty

207 35.00 No. 1 no. SS-304 short branch pipe with nozzle 1994.75 Rupees One No.

208 35.00 No. MS Outdoor Type Hose cabinet stand mounted type 3232.00 Rupees One No.

fabricated out of MS sheet of 16 swg. with glass front (4mm Thousand Nine

thick glass with rubber beading) door and size of the Hundred Ninty

cabinet shall be 600mm x 750 mm x 250 mm Quoted rate

shall include suitable stand for mounting, all fasteners etc,

and cabinet shall be powder coated of approved colour

both inside and outside.

209 25.00 No. Supplying, installing, testing and commissioning of S.S. 1292.80 Rupees One No.

orifice plate of 6 mm thk. For single hydrant.40mm Thousand Two

210 1.00 No. Supplying, installing and commissioning of fire brigade 15453.00 Rupees Fifteen No.

Siamese connection of 4 way with 4 nos. 63 mm dia. built - Thousand Four

in Gun metal Non- return valves instantaneous coupling Hundred Fifty

type arranged on 150 mm dia. Pipe manifold and

connected to wet riser main. Quoted rate shall be included

with C.I. Butterfly valve, C.I. Non-return valve etc.

complete. Piping to be considered as per the approved

211 1.00 No. Supplying, installing and commissioning of fire brigade 24745.00 Rupees Twenty No.

Breeching connection of 2 way with 2 nos. 63 mm dia. built - Four Thousand

in Gun metal Non- return valves instantaneous coupling Seven Hundred

Forty Five Only

type arranged on 150 mm dia. Pipe manifold and

connected to fire water tank. Quoted rate shall be included

with C.I. Butterfly valve etc. complete.. (For fire tank filling)

212 10.00 No. Supplying, installing, testing and commissioning of 25mm 2525.00 Rupees Two No.

dia GM air release valve with copper alloy globe valve. Thousand Five

213 2000.00 Kg SITC of Steel Structure for supporting 116.15 Rupees One Kg

Hundred Sixteen

& Paise Fifteen

214 325.00 No. Providing, fixing, testing & commissioning of 15mm dia 454.50 Rupees Four No.

quartzoid bulb type sprinklers of rating 57 degree Hundred Fifty

centigrade with required accessories : Pendent Sprinkler Four & Paise

215 40.00 No. Providing, fixing, testing & commissioning of U.L. listed/ FM 1649.33 Rupees One No.

approved corrugated SS-304 Braided flexible sprinkler pipe Thousand Six

droplet for 12 kg/ sq. cm. working pressure with 1/2" BSP Hundred Forty

threaded outlet & 1" BSP threaded inlet with reducer nipple,

Thirty Three Only

snap, clamp, T-bar bracket etc. with necessary fitting

complete as required. 1200 mm length

216 240.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 1666.50 Rupees One Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Thousand Six

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Hundred Sixty

Six & Paise Fifty

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members.10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 100mm nominal dia

217 115.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 1565.50 Rupees One Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Thousand Five

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Hundred Sixty

Five & Paise Fifty

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members. 10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 80mm nominal dia

218 160.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 1385.72 Rupees One Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Thousand Three

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Hundred Eighty

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members. 10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 65mm nominal dia

219 475.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 909.00 Rupees Nine Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Hundred Nine

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Only

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members.10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 50mm nominal dia

220 275.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 696.90 Rupees Six Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Hundred Ninty

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Six & Paise Ninty

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members. 10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 40mm nominal dia

221 1075.00 Rmt Supply, Installation, Testing & commissioning of Mild Steel 484.80 Rupees Four Rmt

black pipes, ERW, Heavy grade conforming to IS:1239 up Hundred Eighty

to 150 mm dia. and IS:3589 for pipes above 150 mm dia. Four & Paise

complete with fittings, reducers, tees, high tech supports,

structural clamps such as rods, channels, angles, nuts,

bolts & washers, as required to be firmly mounted on the

steel structural members. 10 % of all the welded joints shall

be done radiographically tested and 50% of the joints

radiographed shall be the "Field Joints" & hydrostatic

testing for 2 hours at 150% of the system pressure, hook-

Painting for piping, fittings, hanger support with U clamp, U

bolt, threaded rods, nut, bolts & washers & structural pipe

support shall be as per technical specification with all

accessories as per approved drawings, specification and

direction of the Engineer-in-Charge. ( Pipe - JINDAL Make)

MS structural supports & Civil pedestal will be paid

separately 25mm nominal dia

222 15.00 No. Supplying, installing and commissioning of Cast iron wafer 3989.50 Rupees Three No.

type lever operated butterfly valve conf. to IS: 13095, PN- Thousand Nine

16 with fittings, flanges, nut, bolts & washers, etc. MOC of Hundred Eighty

the Body & disc shall be CI as per IS:210 FG200, EPDM /

Neoprene seat, carbon steel (EN8) shaft and nylon / Teflon

bearing. Valves exceeding 150 mm dia shall be gear

operated. 80mm nominal dia.

223 40.00 No. Providing , supplying & Installation of ABC Dry Powder type 2398.75 Rupees Two No.

- 6 Kg. Capacity as per IS:15683 Thousand Three

224 40.00 No. Providing , supplying & Installation of CO2 type - 4.5 Kg. 5858.00 Rupees Five No.

Capacity as per IS:15683. Thousand Eight

225 2.00 No. Supply & Installation of Sand buckets of 9L capacity as per 424.20 Rupees Four No.

IS:2546 Hundred Twenty

226 1.00 No. Supply & Installation of M.S stand & canopy for housing 2 1515.00 Rupees One No.

nos of sand buckets of 9L capacity Thousand Five

Hundred Fifteen

227 1.00 No. Providing & fixing of FRP MOBILE FOAM TROLLEY 200 146450.00 Rupees One No.

Ltrs. Stored Pressure Type Controllable discharge Lakh Forty Six

mechanism applicable. Thousand Four

228 1.00 No. Making all liaisoning work for getting provisional & Final 202000.00 Rupees Two No.

CFO NOC, as filling necessary applications, submission of Lakhs Two

forms for approval to the municipal authorities, depositing Thousand Only

and making channels for the necessary fees and other

amounts as required for getting the premises / installations

inspected and approved and all other formalities required

till the sewer / storm water connection is obtained. All the

expenses incurred in this regard shall be borne by the

Contractor, except for the payments to be made for any

security deposits which will be reimbursed on production of

original voucher.

229 100.00 Cum Supplying & stacking sludge / well decayed farm yard 555.50 Rupees Five Cum

manure from the source approved by the engineer in Hundred Fifty

charge incl. screening, loading, unloading, conveyance and Five & Paise Fifty

stacking at site.

230 250.00 Cum Spreading river silt / good earth / sludge / well decayed 126.25 Rupees One Cum

farm yard manure in required thickness as directed. Hundred Twenty

Twenty Five Only

231 350.00 Sqmt Grassing with 'Doob' grass in rows 7.5cm apart in either 60.60 Rupees Sixty & Sqmt

direction including watering and maintenance of the lawn Paise Sixty Only

for 45 days or more till the grass forms a thick lawn free

from weeds and fit for moving.

232 350.00 Sqmt Making lawns including ploughing and breaking of clod, 35.35 Rupees Thirty Sqmt

removal of rubbish, dressing and supplying doob grass Five & Paise

roots and planting at 15 cm apart, including supplying and Thirty Five Only

spreading of farm yard manure at a rate of 0.18 cum per

233 750.00 Kg Supplying doob grass of approved quality at site. 15.15 Rupees Fifteen & Kg

234 500.00 No. Making tree guard 53 cm dia and 1.3 m high as per design 176.75 Rupees One No.

from empty bitumen drum, slit suitably to permit sun and Hundred Seventy

air, including providing and fixing 2 nos M S sheet rings 50 Six & Paise

x 0.5 mm with rivets complete in all respect (Empty bitumen

drum to be supplied by the dept. at free of cost )

235 450.00 No. Planting trees, flower plants and/or shrubs of specified 151.50 Rupees One No.

variety by excavating pits of size 60x60x60 cm, refilling the Hundred Fifty

same by providing and mixing farm yard manure at a rate One & Paise Fifty

of 0.06 cum per pit, watering and maintaining till well

established (about 45 days) complete.

236 500.00 No. Supplying well grown trees, flower plants and/or shrubs of 101.00 Rupees One No.

specified variety as approved by the EIC at site. Hundred One

237 500.00 Sqmt Clearing grass and removal of rubbish manually upto a 5.05 Rupees Five & Sqmt

distance of 50m outside the periphery of the area. Paise Five Only

238 1000.00 Sqmt Clearing the land by uprooting rank vegetation, grass, 15.15 Rupees Fifteen & Sqmt

bushes, shrubs, saplings and trees girth upto 300mm, and Paise Fifteen

disposal upto 1 km. including all labour, tools & plants etc Only

TOTAL OF CIVIL WORK …. A Rs.

PART 'B' ELECTRIC WORK:

239 776 Pt. Point wiring for Tissino / Modular secondary light point with 151.50 Rupees One Pt.

2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are Hundred Fifty

of ISI marked 1.1 KV grade FRLS PVC insulated multi One & Paise Fifty

strand copper wires, in below type of pipe to be erected

complete with earth continuity and necessary connection

with primary light with accessories erected on Metal / PVC

/ wooden box covered with 3 mm thick PC(Polycarbonate) /

Acrylic sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as directed.

Note:- Maximum up to 6 mtrs length, excess will be

considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

240 676 Pt. Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire 449.45 Rupees Four Pt.

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade Hundred Forty

FRLS PVC insulated multi strand copper wires up to 10 mtr Nine & Paise

Forty Five Only

length , in below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with

textured/metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

241 200 Pt. Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 629.23 Rupees Six Pt.

sq.mm (Green) both are of .ISI marked 1.1 KV Grade Hundred Twenty

FRLS PVC insulated multi strand copper wires up to 10 mtr Nine & Paise

length, in below type of pipe erected with 6A Modular type

switch and hum free EME four or more step type electronic

fan regulator with separately mounted and accessories

with earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered

with textured/metallic/white front plate modules erected on

/ in wall / ceiling as per pipe erected. with necessary ceiling

rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

242 163 Pt. Point wiring for Individual Plug with & earth wire of 1.5 473.69 Rupees Four Pt.

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS Hundred Seventy

PVC insulated multi strand copper wires up to 10 mtr Three & Paise

Sixty Nine Only

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories. [I] For 6A Plug and 6 a

switch with 2-1.5 sq.mm Cu. Wire from nearby

switchboard/mcb db board (f) with medium class Rigid

PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

243 278 Pt. [III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. 818.10 Rupees Eight Pt.

Wire with 2.5 sq.mm ( green) earthing wire from mcb db Hundred

board. (f) with medium class Rigid PVC pipe and Eighteen & Paise

accessories erected concealed in wall/ceiling complete

243 80 Pt. Point wiring for on board Looped Plug with 6A Modular type 241.39 Rupees Two Pt.

switch & 5 pin socket erected on PVC / Metallic/Wooden Hundred Forty

box, single mounting base frame covered with textured / One & Paise

Thirty Nine Only

metallic/white front plate modules erected on / in wall /

ceiling with following type accessories. Cat. III

244 15 Pt. Point wiring for Two Way Controlled Light Point with 2-1.5 560.55 Rupees Five Pt.

sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI Hundred Sixty &

marked 1.1 KV grade FRLS PVC insulated multi strand Paise Fifty Five

copper wires erected in below type of pipe with 6A Modular

type switches and following type of accessories erected on

PVC / Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected. with

necessary batten/angle holder or ceiling rose or

H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

245 3 Pt. Providing following type of Modular Type Accessories 190.89 Rupees One Pt.

mounted with PVC / metallic/Wooden box, single mounting Hundred Ninty &

base frame covered with textured / metallic/white front plate Paise Eighty

, modules erected with necessary connections as per site

situation directed by Engineer In charge.

(3) Two Pin/RJ-11 Telephone Socket

[B] For Two Gang

as per technical specification etc. as required.

246 1 Each Providing following type of Modular Type Accessories 153.52 Rupees One Each

mounted with PVC / metallic/Wooden box, single mounting Hundred Fifty

base frame covered with textured / metallic/white front plate Three & Paise

, modules erected with necessary connections as per site

situation directed by Engineer In charge.

(4) TV Co-axial Socket outlet

as per technical specification etc. as required.

247 108 Each Providing following type of Modular Type Accessories 153.52 Rupees One Each

mounted with PVC / metallic/Wooden box, single mounting Hundred Fifty

base frame covered with textured / metallic/white front plate Three & Paise

, modules erected with necessary connections as per site

situation directed by Engineer In charge.

Computer RJ-45 socket Cat. III.

as per technical specification etc. as required.

248 1 No. Providing following type of Modular Type Accessories 314.11 Rupees Three No.

mounted with PVC / metallic/Wooden box, single mounting Hundred

base frame covered with textured / metallic/white front plate Fourteen & Paise

, modules erected with necessary connections as per site

situation directed by Engineer In charge. (19) Modular

Indicating Call Bell Cat. III

249 1 No. Providing following type of Modular Type Accessories 143.42 Rupees One No.

mounted with PVC / metallic/Wooden box, single mounting Hundred Forty

base frame covered with textured / metallic/white front plate Three & Paise

, modules erected with necessary connections as per site

situation directed by Engineer In charge. (20) Modular

Buzzer Cat. III

250 100 Mtr. Providing and erecting ISI mark Medium class RIGID PVC 32.32 Rupees Thirty Mtr.

PIPES of following size complete to be erected on/in wall or Two & Paise

ceiling erected with necessary PVC fittings & Junction Thirty Two Only

boxes fixed with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed 25mm

251 100 Mtr. Providing and erecting ISI mark Medium class RIGID PVC 64.64 Rupees Sixty Mtr.

PIPES of following size complete to be erected on/in wall or Four & Paise

ceiling erected with necessary PVC fittings & Junction Sixty Four Only

boxes fixed with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed 40mm

252 960 Mtr. MAINS : Providing and erecting Mains with 1.1 KV grade 59.59 Rupees Fifty Mtr.

FRLS PVC insulated ISI marked stranded Copper Nine & Paise

conductor wire in following type of pipe to be erected Fifty Nine Only

concealed in /flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories (a) 2 wire

253 4644 Mtr. Providing and erecting Mains with 1.1 KV grade FRLS PVC 78.78 Rupees Seventy Mtr.

insulated ISI marked stranded Copper conductor wire in Eight & Paise

following type of pipe to be erected concealed in /flushed Seventy Eight

on wall/ceiling, with 1.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (b) 2 wire 2.5 sq. mm

254 353 Mtr. providing and erecting Mains with 1.1 KV grade FRLS PVC 107.06 Rupees One Mtr.

insulated ISI marked stranded Copper conductor wire in Hundred Seven

following type of pipe to be erected in / on wall / ceiling with & Paise Six Only

2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and

accessories (a) 2 wire 4 sq. mm

255 2120 Mtr. providing and erecting Mains with 1.1 KV grade FRLS PVC 140.39 Rupees One Mtr.

insulated ISI marked stranded Copper conductor wire in Hundred Forty &

following type of pipe to be erected in / on wall / ceiling with Paise Thirty Nine

2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and

accessories (b) 2 wire 6 sq. mm

256 402 Mtr. providing and erecting Mains with 1.1 KV grade FRLS PVC 172.71 Rupees One Mtr.

insulated ISI marked stranded Copper conductor wire in Hundred Seventy

following type of pipe to be erected in / on wall / ceiling with Two & Paise

2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and

accessories (g) 4 wire 4 sq. mm

257 480 Mtr. providing and erecting Mains with ISI marked, 1.5KV grade 26.26 Rupees Twenty Mtr.

electrolyte multi stranded, annealed copper conductor with Six & Paise

heat resistant PVC insulated conforms to IS 694, IEC - 227 Twenty Six Only

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required.

(c) One wire 2.50 sq. mm

258 380 Mtr. providing and erecting Mains with ISI marked, 1.5KV grade 35.35 Rupees Thirty Mtr.

electrolyte multi stranded, annealed copper conductor with Five & Paise

heat resistant PVC insulated conforms to IS 694, IEC - 227 Thirty Five Only

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (d) One wire 4.00 sq. mm

259 110 Mtr. providing and erecting Mains with ISI marked, 1.5KV grade 53.53 Rupees Fifty Mtr.

electrolyte multi stranded, annealed copper conductor with Three & Paise

heat resistant PVC insulated conforms to IS 694, IEC - 227 Fifty Three Only

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (e) One wire 6.00 sq. mm

260 175 Mtr. providing and erecting Mains with ISI marked, 1.5KV grade 87.87 Rupees Eighty Mtr.

electrolyte multi stranded, annealed copper conductor with Seven & Paise

heat resistant PVC insulated conforms to IS 694, IEC - 227 Eighty Seven

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (f) One wire 10.00 sq. mm

261 165 Mtr. providing and erecting Mains with ISI marked, 1.5KV grade 135.34 Rupees One Mtr.

electrolyte multi stranded, annealed copper conductor with Hundred Thirty

heat resistant PVC insulated conforms to IS 694, IEC - 227 Five & Paise

Thirty Four Only

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (g) One wire 16.00 sq. mm

262 60 Mtr. providing and erecting Mains with ISI marked, 1.5KV grade 225.23 Rupees Two Mtr.

electrolyte multi stranded, annealed copper conductor with Hundred Twenty

heat resistant PVC insulated conforms to IS 694, IEC - 227 Five & Paise

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (h) One wire 25.00 sq. mm

263 385 Mtr Supplying and erecting Flexible PVC insulated multi strand 44.44 Rupees Forty Mtr

multi core 1.1 kv grade ISI marked copper wires of Four & Paise

following size to be erected as directed. Forty Four Only

e) 1.50 Sq.mm 3 core round PVC sheathed

264 100 Mtr. Providing & Erecting approved make following size of TV 37.37 Rupees Thirty Mtr.

Co-axial flexible cable comprising inner conductor of solid Seven & Paise

bare copper insulated with Foam PE & Secondary Thirty Seven

conductor made of poly - Aluminium film bonded Al. Braids

@ suitable coverage overall sheathed with black PVC

as per technical specification etc. as required.

265 50 Mtr. Supplying & erecting approved make Telephone Cable 19.19 Rupees Ninteen Mtr.

electrolytic copper conductor PE insulation twisted in two & Paise Ninteen

pairs, & wrapped with FRLS PVC tape & sheathed with Only

FRLS PVC or HFFR outer Jacket suitable for telephone

wiring & confirming to C-DOT erected in existing pipe. of

following size of conductors & nos.of pairs. With necessary

[A] Conductor Size 0.5 mm

(a) Unarmoured (2) Two Pairs

266 50 Mtr. Supplying & erecting approved make Telephone Cable 120.19 Rupees One Mtr.

electrolytic copper conductor PE insulation twisted in two Hundred Twenty

pairs, & wrapped with FRLS PVC tape & sheathed with & Paise Ninteen

FRLS PVC or HFFR outer Jacket suitable for telephone

wiring & confirming to C-DOT erected in existing pipe. of

following size of conductors & nos.of pairs. With necessary

connections.(b) Armoured [Jelly Filled] (1) Ten Pairs

267 1 Each Providing & erecting main Distribution (MDF) indoor type, 949.40 Rupees Nine Each

back mounted frame as per DoT standard approved with Hundred Forty

krone strips Nine & Paise

(a) Suitable for 10 pair

268 1 No. Providing & erecting Switch board for Computer or electric 1081.71 Rupees One No.

apparatus consisting of following modular type accessories Thousand Eighty

mounted with PVC / Metallic concealed/open box with One & Paise

single mounting base frame covered with textured/metallic

/white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat.

269 24 No. Providing following type of Modular Type Accessories 473.69 Rupees Four No.

mounted with PVC / metallic box, single mounting base Hundred Seventy

frame covered with textured / metallic/white front plate , Three & Paise

Sixty Nine Only

modules erected with necessary connections as per site

situation directed by Engineer In charge. LIGHTING

FIXTURE : Foot Light as per colour requirement with

concealed box, modular accessories, acrylic glass cover

with suitable LED watt with all accessories as per following

module (b) Four modules

270 63 No. Supplying and erecting led lamps with following wattage 188.87 Rupees One No.

capacity of 220 to 240 voltage, minimum 15000 burning Hundred Eighty

hours life, 500 V in built-surge protection,Polycarbonate Eight & Paise

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (iii) 10 to 15 watts (Cat-

271 796 No. Supplying and erecting LED indoor fittings with LEDs of 427.23 Rupees Four No.

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, Hundred Twenty

with housing used as a heat sink shall be made of thick Seven & Paise

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)(A) Square/ Circular

shaped Surface/Recessed Mount Downlight with provision

for spring loaded mounting clips complete.IP20 (ii) 11-15

watts, Surge-2 KV Cat-lll

272 521 No. Supplying and erecting LED indoor fittings with LEDs of 589.84 Rupees Five No.

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, Hundred Eighty

with housing used as a heat sink shall be made of thick Nine & Paise

Eighty Four Only

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)(A) Square/ Circular

shaped Surface/Recessed Mount Downlight with provision

for spring loaded mounting clips complete.IP20 (iii) 16-20

watts, Surge-2 KV Cat-lll

273 10 No. Supplying and erecting LED indoor fittings with LEDs of 758.51 Rupees Seven No.

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, Hundred Fifty

with housing used as a heat sink shall be made of thick Eight & Paise

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)(A) Square/ Circular

shaped Surface/Recessed Mount Downlight with provision

for spring loaded mounting clips complete.IP20 (iv) 22-24

watts, Surge-2 KV Cat-llI

274 20 No. Supplying and erecting LED indoor fittings with LEDs of 373.70 Rupees Three No.

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, Hundred Seventy

with housing used as a heat sink shall be made of thick Three & Paise

sheet Steel conforming to IS: 513/CRCA/ aluminium die

cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Tube Light with

integral driver (iv) 22-24 Watts, Surge - 2KV,IP-20, 4 feet

275 40 No. Supplying and erecting LED indoor fittings with LEDs of 1794.77 Rupees One No.

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, Thousand Seven

with housing used as a heat sink shall be made of thick Hundred Ninty

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name

120 to 300 V,Power Factor more than 0.95, THD < 10 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED efficiency

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (D) LED Panel Light

with provision for Plane front frame with translucent cover

fixed to housing complete.IP20

(vi) 36 watts, 24" x 24" mm, Surge- 2KV, Cat-lll

276A 20 No. Supplying and erecting LED street light / Flood light fittings 10818.11 Rupees Ten No.

with High power White LEDs wattage of 3 Watt and above Thousand Eight

assembled on single MCPCB, efficiency more than 130 Hundred

Eighteen & Paise

lm/w and corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/

lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more

than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges

of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges

(B) Flood Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage

(vii)above 200 to 250 watts Cat-llI

276B 22 No. (c) LED Bollard fittings of minimum height 1000 mm & 4461.17 Rupees Four No.

dia.100mm having polycarbonate clear/milky diffuser Thousand Four

mounted on 3mm thick aluminium finished powder coated Hundred Sixty

pipe with base plate 160x160mm with erection by

M8x75mm fastner with required RCC foundation.IP65 for

to 20 watt and above ,surge-4kv cat-III

277 35 No. STREET LIGHT FIXTURE 4819.72 Rupees Four No.

Supplying and erecting LED street light / Flood light fittings Thousand Eight

with High power White LEDs wattage of 3 Watt and above Hundred Ninteen

& Paise Seventy

assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/

lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more

than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges

of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges

shown.) (C) Post Top Lantern LED fitting comprises of

Copper dust finish cast aluminum spigot and spun

aluminum canopy fixed with opal polycarbonate, pipe

arrangement for vertical mounting driver and accessories

wired upto terminal block.IP 65 (b)32-40W Cat-lll

278A 158 Ea. Supplying & erecting following spare parts for panel 386.83 Rupees Three Ea.

mounting Switch Disconnector Fuse Units Cable Terminal ( Hundred Eighty

‘Plain" Type)Set of Four for (i) 32 / 63 Amps Six & Paise

278B 100 Ea. Supplying & erecting following spare parts for panel 814.06 Rupees Eight Ea.

mounting Switch Disconnector Fuse Units Cable Terminal ( Hundred

‘Plain" Type)Set of Four for (ii) 125 / 200 Amps Fourteen & Paise

279 2 Ea. providing and erecting Approved make Four pole moulded 6173.12 Rupees Six Ea.

case circuit breaker having breaking capacity ICU of 25 KA. Thousand One

at 415 V,having normal current rating up to 25 A to 100A. Hundred Seventy

with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 c/s. with all internal connections & complete

erected in existing 16 G.M.S. housing. ICS=100% of ICU

280 13 Ea. providing and erecting Approved make Four pole moulded 8055.76 Rupees Eight Ea.

case circuit breaker having breaking capacity ICU of 35 KA. Thousand Fifty

at 415 V. having normal current rating 125A. with Fixed Five & Paise

Seventy Six Only

thermal & magnetic release suitable to work on A.C.supply

50 c/s. with all internal connections & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only

281 4 Ea. providing and erecting Approved make Four pole moulded 16221.61 Rupees Sixteen Ea.

case circuit breaker having breaking capacity ICU of 35 KA. Thousand Two

at 415 V. having Normal current rating 200A.with variable Hundred Twenty

Thermal & magnetic release suitable to work on A.C.supply

50 c/s. with all internal connections & complete erected in

existing 16 G.M.S.housing. ICS=100% of ICU only

282 2 Ea. providing and erecting Approved make Four pole moulded 25228.79 Rupees Twenty Ea.

case circuit breaker having breaking capacity ICU of 50 KA Five Thousand

and above at 415 V having Normal current rating 400A. Two Hundred

with variable Thermal & magnetic release suitable to work

on A.C.supply 50 c/s. With all internal connections &

complete erected in existing 16 G.M.S. housing. ICS=100%

of ICU only Cat III

283 1 Ea. Providing and erecting Approved make Four pole moulded 28173.95 Rupees Twenty Ea.

case circuit breaker having breaking capacity ICU of 50 Eight Thousand

K.A. and above at 415 V having normal current rating up One Hundred

Seventy Three &

to 630A. with variable thermal & magnetic release suitable

Paise Ninty Five

to work on A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing

ICS=100% of ICU only Cat III

284 1 Ea. Providing and erecting Approved make Earth fault Relay 6056.97 Rupees Six Ea.

suitable to mount with inter connection suitable to following Thousand Fifty

size of moulded case circuit breaker having CT ratio & Six & Paise Ninty

MCCB rating as following along with shunt trip 220V AC.

with all internal connections & complete erected in existing

285 14 Ea. Supplying & erecting following spare parts for panel 420.16 Rupees Four Ea.

mounting Switch Disconnector Fuse Units Operational Hundred Twenty

Handle Assembly Complete for (i) 32 / 63 / 125 Amps & Paise Sixteen

286 7 Ea. Supplying & erecting following spare parts for panel 754.47 Rupees Seven Ea.

mounting Switch Disconnector Fuse Units Operational Hundred Fifty

Handle Assembly Complete for (ii) 200 / 250 / 320 / 400 / Four & Paise

Forty Seven Only

287 8 Ea. Supplying & erecting following spare parts for panel 137.36 Rupees One Ea.

mounting Switch Disconnector Fuse Units Neutral Link for Hundred Thirty

(i) 32 / 63 / 125 Amps Seven & Paise

Thirty Six Only

288A 14 Rmtr Supplying and erecting triple pole & neutral 440V/ 500V 660.54 Rupees Six Rmtr

panel mounting Aluminium Busbars with four equal Nos. of Hundred Sixty &

bus having current density not more than 0.8 Amp. / sq.mm Paise Fifty Four

(Rated current / cross section area) duly wrapped with

colour insulating tape for phase sequence of following

current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each

busbar,erected in existing cubical panel with necessary

(A) Suitable for 100 Amp. Capaci

288B 12 Rmtr (B) Suitable for 200 Amp. Capacity 1037.27 Rupees One Rmtr

Thousand Thirty

288C 3 Rmtr (D) Suitable for 400 Amp. Capacity 2204.83 Rupees Two Rmtr

288D 3 Rmtr (E) Suitable for 630 Amp. capacity 3061.31 Rupees Three Rmtr

Thirty One Only

289 1 Rmtr Supplying and erecting triple pole & neutral 440V / 500V 1961.42 Rupees One Rmtr

panel mounting Copper Busbars with four equal Nos. of Thousand Nine

electrolyte bus having current density not more than 1.6 Hundred Sixty

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

(A) Suitable for 100 Amp. Capacity

290 107 Ea. Providing & erecting 240 V MCB double pole switch for 299.97 Rupees Two Ea.

motor & inductive load (C Curve) having 10 KA breaking Hundred Ninty

capacity & confirms to IS : 8828 in existing box having Nine & Paise

Ninty Seven Only

following capacity (A) 6 to 32 Amp. (III)

291 1371 Ea. providing and erecting Miniature circuit breaker single pole 112.11 Rupees One Ea.

6A to 25A suitable to operate on 240 V A.C. system and Hundred Twelve

having breaking capacity 10 KA to be erected in existing & Paise Eleven

box. confirming to IS 8828/1996 with ISI Mark (Cat.III)

292A 7 Ea. Providing & erecting 415V MCB Four Pole Switch for 595.90 Rupees Five Ea.

Lighting Load (B curve) having 10KA breaking capacity & Hundred Ninty

confirms to IS :8828 in existing box having following Five & Paise

(a) 6 to 32 Amp. (III)

292B 49 Ea. (b)40 Amp. (III) 668.62 Rupees Six Ea.

292C 20 Ea. (c)63 Amp. (III) 737.30 Rupees Seven Ea.

293 159 Ea. providing and erecting Approved make RCCBs conforming 1969.50 Rupees One Ea.

to IS: 12640 and having sensitivity of 30 mA and Short Thousand Nine

Circuit withstand capacity of 10 KA and suitable for Hundred Sixty

operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance

feature & do not incorporate any electronic component. for

following Max. rating erected as directed (i) 25 Amps.DP -

294 102 No. Providing and erecting Sheet Steel powder coated MCB 1492.78 Rupees One No.

distribution board - flush / surface mounted fitted with Thousand Four

busbar, neutral link, earth bar and DIN rail, Conforms to IS Hundred Ninty

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase

(b) sheet steel double door (IP-43)

295 19 No. Providing and erecting Sheet Steel powder coated MCB 1152.41 Rupees One No.

distribution board - flush / surface mounted fitted with Thousand One

busbar, neutral link, earth bar and DIN rail, Conforms to IS Hundred Fifty

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase

(b) sheet steel double door (IP-43)

296 5 Ea. Providing and erecting metallic vitrified danger notice board 69.69 Rupees Sixty Ea.

as per language suggested by engineer incharge for Nine & Paise

MEDIUM VOLTAGE installation to be erected as per IS- Sixty Nine Only

297 5 Ea. Providing and erecting metallic vitrified danger notice board 81.81 Rupees Eighty Ea.

as per language suggested by engineer incharge for HIGH One & Paise

VOLTAGE installation to be erected as per IS.-2551. Eighty One Only

298 948 Kg. Providing and erecting required size HOT deep Galvanised 77.77 Rupees Seventy Kg.

iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT Seven & Paise

panel board, Motors etc. using proper clamp. Seventy Seven

299 96 Kg. Providing and erecting required size Copper strip for 794.87 Rupees Seven Kg.

earthing of H.T. OCB / ACB/ Transformer, LT panel board, Hundred Ninty

Motors etc. using copper clamp. Four & Paise

300 50 Kg. Providing and erecting Annealed bare Copper wire 8 to 16 794.87 Rupees Seven Kg.

SWG. Hundred Ninty

301 45 No. Providing and erecting Pipe type earthing having 150 368.65 Rupees Three No.

cms.long and 2.5 cms. dia. galvanised iron pipe with Hundred Sixty

coupling and buch buried in specially prepared earth pit Eight & Paise

Sixty Five Only

complete with necessary 8 SWG earth wire.

302 6 Ea. Supplying & erecting in earthpit of minimum bore dia. 10593.89 Rupees Ten Ea.

225mm size approved make Safe Earthing Electrode Thousand Five

consisting Pipe-in-Pipe Technology as per IS 3043-1987 Hundred Ninty

made of corrosion free hot dipped G.I.Pipes having Outer

Eighty Nine Only

pipe dia of 80 mm having 80-200 Micron galvanising, Inner

pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications

with chamber and heavy duty cover (A)(approved make

OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of

earthing resistane mentioned in test Certificate) & having

back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry

form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture

for long time Necessary test report must be submitted by

[C] For Electrical Installation covering Transformer

Neutrals, Lightning arrester Earthing, A.C.Plant &

Sensitive Computer System(like Automation,

SCADA)i.e. independent Earthing located in other than

normal soil i.e. Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg.

303 16 Ea. Supplying & erecting in earthpit of minimum bore dia. 5842.85 Rupees Five Ea.

225mm size approved make Safe Earthing Electrode Thousand Eight

consisting Pipe-in-Pipe Technology as per IS 3043-1987 Hundred Forty

made of corrosion free hot dipped G.I.Pipes having Outer

Eighty Five Only

pipe dia of 80 mm having 80-200 Micron galvanising, Inner

pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications

with chamber and heavy duty cover (A)(approved make

OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of

earthing resistane mentioned in test Certificate) & having

back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry

form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture

for long time Necessary test report must be submitted by

[A] For electrical installation up to 440 V

Length of Pipe - 1 Mtr

Back filling compound - 1 Nos. of Bag of 15 Kgs.

304 2 Ea Providing one bag of 25 Kg. Additional Back Filling 707.00 Rupees Seven Ea

Compound (BFC) suitable for safe earthing device. Hundred Seven

305A 18 Sq.Mtr Providing & erecting weather proof, dust & vermin proof, 14902.55 Rupees Fourteen Sq.Mtr

floor mounted front operated indoor type cubical panel Thousand Nine

board necessary IP-42 and above protection as per Hundred Two &

Paise Fifty Five

approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S.sheet for internal partitions with necessary

accesories , supporting angles/ flats channel including

cutting, bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements & instruction of

engineer-in-charge with erection of supplied switch gears,

BUSBARS, suitable size of inter connecting PVC copper

wire / copper-aluminium strips, rubber grommets, rib,

bakelite control fuses/MCB for measuring instruments,

earth bus & earth bolts, foundation flange - bolts-base

Plates, sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating. (The rates excludes

the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams) The

panel shall be supplied with following approved

manufacturers with following size.

(A) The standard companies switch gear shall be used and

only manufacturers at CPRI approved factory as per IEC

61439 for beneficial use. (i) with 350mm depth

305B 5 Sq.Mtr Providing & erecting weather proof, dust & vermin proof, 40999.94 Rupees Forty Sq.Mtr

floor mounted front operated indoor type cubical panel Thousand Nine

board necessary IP-42 and above protection as per Hundred Ninty

approval from engineer incharge made from 14 SWG thick

Ninty Four Only

CRC M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S.sheet for internal partitions with necessary

accesories , supporting angles/ flats channel including

cutting, bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements & instruction of

engineer-in-charge with erection of supplied switch gears,

BUSBARS, suitable size of inter connecting PVC copper