REPAIR/REPLACEMENT OF DOOR/WINDOW, ROOFING, FLOORING AND MISC B/R WORKS AT TECHNICAL AREA A/B AND RESIDENTIAL AREA OF IRDE UNDER GE (I) RND DEHRADUN

Amount

M&L for cutting down removing vegitation plant digging out penetrated roots with tronices looping branches not exc. 10cm girth PROTRUDING over wall roofs by necessary cutting hole in brick / concrete wall/ surfaces and injecting chemical GLYPHOSPHATW 41% SL 20 ml or till refusal by makimg cut/ injection in the stem of plant 30mm C/C spraying with solution (25ml Glyphospoto 41% diluted with one litre water) and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 and to match the existing work and finishes and removing of debris out side premises/ defence land including necessary scaffolding etc wk will be carried out upto 6 th storey height bldgs complete all as specified & directed.

M&L for PCC 1:2:4 Type B-1 {using 20mm graded crushed stone aggregate} as in coping/benching bed plates roof kerbs mud stops, including weathering, slightly rounded or chamfered angles and throating etc including necessary form work complete all as specified and directed.

M&L for Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills sunshades, shelves lintels etc and cutting chases for concealed water pipe etc and making good cutting not exc 10cm. complete all as specified and directed.

M&L for brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6.00m mean radius built in CM (1:6) complete all as specified and directed.

M&L for cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4 type B-1, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc. one brick complete all as specified and directed.

Taking down shutters of any description and make n. exc. 1 sqm each including removing from site complete all as specified and directed.

Taking down shutters of any description exc 1 sqm & n. exc 2 sqm each including removing from site complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm and n. exc. 4.00 sqm each including removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each including removing from site complete all as specified and directed.

Taking down shutter exc. 1 Sqm and n.exc 2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters of any description. complete all as specified and directed.

M&L for 40 mm thick flush shutters, solid core construction, exterior grade with block board core and plywood face, pannels, commercial type on both sides and one face is covered withdecorative face veneer with lipping / frame to match, including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S&F factory made glazed and Skelton 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars, any numbers , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc; sizes of members of shutters as specified in SSR Part-I section 8, clause 8-24 (a) complete all as specified and directed.

All as per Item No 13 above but area exceeding 2.00 sqm each complete all as specified and directed.

S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain/ colour PVC sheet reinforced with MS square tube as per specification & drawings specified in SSR Part-II 2010 complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC "C" channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing in SSR Part II 2010 etc complete all as specified and directed.

Factory made solid panel PVC wire gauzed shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly complete all as specified and directed.

M&L PVC SHEET of wall paneling of thickness 5mm solid consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cbm density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a U Channel at top, bottom and side edges and strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement with and complete all as specified and directed. (Note- Including all nesscesary fittings and scafolding for heighted site)

S & F in repair 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frames complete all as specified and directed

S& F Factory Made Solid PVC coulour Moulded Door Shutter with wood free EPS, 28 to 30 mm thick (stiles),with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing. Note: Colour approved by GE / Engr-in-Charge

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150 mm size complete all as specified and directed.

S&F floor door stopper double leg of aluminium alloy body of 140 mm length with aluminium base plate of size 50 mm x 40 mm complete all as specified & directed.

S&F in repair floor door stopper double leg of aluminium alloy body of 140 mm length with aluminium base plate of size 50 mm x 40 mm complete all as specified & directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed.

S&F 150 mm, mild steel ordinary helical door spring including roller and roller plate including necessary welding if requried complete all as specified & directed.

S&F in repair 150 mm, mild steel ordinary helical door spring including roller and roller plate including necessary welding if requried complete all as specified & directed.

S&F 125 mm long hasp & staple safty type cold rolled heavy weight cold rolled mild steel with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repair aluminium (die cast) body door closer hydraulically regulated, designation No.3 universal type, suitable for doors shutters up to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed.

S&F in repairs mortice lock, vertical type of size 100 mm with brass body 2 lever complete all as specified.

S&F 25 mm dia, brass, knobs for cupboard fixed with nut, screw and washer of mild steel, bright finised complete all as specified and directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting for cabinets fixed with screws complete all as specified and directed.

S&F stainless steel wire cloth 1.23 mm nominal dia of wire and size of mesh 12 mm and fixed with tinned tacks or galvanized steel wire staples complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm complete all as specified and directed.

S&F 75 mm size stainless steel butt hinges ISI marked medium weight cold rolled and fixed with screws/welded to frame complete all as spd and directed

S&F in repair drapery rod 25 mm dia, high Strength PVC Coated MS rod of thickness 40/60 microne of wood finish with minimum 8 rings in each metre length of rod of ABS Plastic in matching colour & installations brackets of galvanised steel with all accessories complete all as specified and directed.

S&F in repair venetian blind coloured powder coated 35mm wide and 1 mm thick Aluminium alloy blades with opening and closing arrangment including aluminium hanging channel at top with sliding wheel/ring including pulling rope in both side and necessary accessories complete all as specified and directed.

S & F in repair 1.25mm thickness of laths steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, haps and staple and one shop coat of primer erected in position as indicated push pull or manual type complete all as specified and directed

S&F powder coated aluminium frame for doors, windows or partition including aluminium beading, hinges of required size,jointing cleats, screws, dash,fastners,plug for fixing with wall, columns etc complete all as specified & directed.

S&F powder coated of any colour aluminium door shutters, aluminium section like lock rail, bottom rail 115mmX38mmX1.00mm thick and top rail and vertical rail 100mmX38mmX1.00mm thick mm including necessary jointing cleats/glazing clipx, rubber neorene paking, handles 02 Nos in each door, locking arrangment, aluminium snap beading screw etc, complete all as specified and directed. (panels likes prelaminated particle board / sheet glass shall be measured and paid seprately)

S&F powder coated aluminium two track sliding window with two glass shutters (using 4.8mm/ 5 mm thick sheet glass black/ white tinted modi guard) aluminium powder coated section aluminium cleat, PVC track, bearing, handle locking arangement, rubber beading etc complte fittings as approved. Note Size of aluminium section shall be under :- (i)Two track top and vertical - Jindal main-2010 section No 20829 or equivalent as appoved by GE (ii) Two track bottom- Jindal main-2010 section No 20830 or equivalent as appoved by GE (iii) Shutter vertical section- Jindal main- 2010 Section 20606 or equivalent as appoved by GE (iv) Shutter top and bottom - Jindal Main-2010 Section 20604 or equivalent as appoved by GE (v) Shutter vertical middle (interlock) -Jindal Main-2010 section 20605 or equivalent as appoved by GE

S&F powder coated 3 track aluminium sliding window three track with two glass shutters using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperature 1.61 mm using aluminium powder coated section aluminium cleat, PVC track, beading handle, lock, rubber beading etc complete fittings as per manufacture instructions. Note:- Size of aluminium section are as under:- (i) Three track top and vertical - Jindal main 2010 section No 20621 or equivalent as approved by GE (ii) Three track bottom- Jindal main - 2010 section No 20620 or equivalent as approved by GE (iii) Shtter vertical section- Jindal main 2010- section No 20606 or equivalent as approved by GE (iv) Shutter top and bottom- Jindal Main- 2010 Section 20604 or equivalent as approved by GE (v) shutter verticle middle ( Interlock) - Jindal main - Section or equivalent approved by GE.

S&F in repair plain aluminium sheet, 0.56 mm thick lining to bottom rail of toilet / bath door shutters and straight flashing, fixed with brass, chromium plated screws etc complete all as specified and directed.

Taking down aluminium shutter exc. 1 Sqm and n.exc 2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters and replacement of top rail, lock rail or bottom rail where required of any description. complete all as specified & directed.

S&F 5 mm thick aluminum composit pannel fixed or laid on door or partition by using rubber based adhesive complete all as specified & directed.

S&F in repair aluminium anodised grill with mesh size 75mm and aluminium bar 6mm XPM type including all necessary accesseries such as channel for fixing grill, screw etc aluminium section 15 micron thick anodizing complete all as specified and directed.

S&F mild steel work framed work as in door and gates of angle or other sections and similar items confirming to FE-290 (Gde E-165) complete all as specified & directed.

S&F 19 mm thick Solid PVC board fixed with steel screw and synthetic adhesive both one side balancing color texture used for shutter of the cabinet / cupboard and complete all as specified and directed.

S&F 19 mm thick Solid PVC board fixed with steel screw and synthetic adhesive both side balancing white texture used for shutter of the cabinet / cupboard and complete all as specified and directed.

Providing & fixing false ceiling at all heights with perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter- locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L- shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge.

M&L for non skid Ceramic tiles,first quality( of approved class , colour and design/ shade ) 6 to 7 mm thick( square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor surface etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles over and including 15 mm Screed bed in CM 1: 6 with complete all as specified and directed.

M&L for non-skid coloured ceramic tiles first quality (of approved class, colour and design/shade) 7 to 8 mm thick (square/rectangular) as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 10 mm thick rendering in cement mortar (1:4),with complete all as specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of size 300x200x7mm/ 350x250x7mm/ 450x350x7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M & L for taking down old cement plaster/Grit wash on stone wall or brick surfaces of walls including raking out joints, hacking for key and scrubbing down with water with and including, removing debris out sideMOD Land at contractor is own arrangement ) complete all as specified & directed. complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete /brick surface in cement mortar 1:6 finished fair and even as in wall etc complete all as specified and directed.

M&L for prepration of new plaster surfaces of wall and applying two coat of oil bound distemper over and including a coat of alkali primer & 3 mm thick wall care puttty complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames glazed with putty or fixed with beads including punching or drilling out old glazing pins/spring clips etc complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality in panes not exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality in panes exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

M&L for 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

M&L for 4 mm thick figured glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

M&L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

Taking up or down existing GI tubing and connections, including cleaning for refixing and making good the disturbed surface for 20 mm dia pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including cleaning for refixing and making good the disturbed surface for 15 mm dia pipes complete all as specified and directed.

S&F for laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F for laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L Cleaning and removing all scale and dirt, etc. from tanks and form mouths of circulating pipes, etc, capacity of tank exc 250 & n exc 500 litres including writing date of cleaning on the tank with suitable synthetic enamel paint etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed.

Demolition of brick or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone works and precast concrete articles and with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed.

Dismantling of wall and ceiling boards any thickness including cover filletes with and including with and including removing Debris out sideMOD Land at contractor is own arrangement complete all as specified and directed.

Notes for item No. 1 to 73:- (i) The work will be carried out upto 6th storey bldgs. Hence necessary complete scaffolding and other safety arrangements will be managed and made by tenderer/ Contractor accordingly at own expense. (ii) Tenderer kind attention is also invited to srl clause 1.16 of Sec-I on srl page No 1 to 150 (General rules for Safety in Construction) as specified in SSR Pt-I (2009) for safety measures/ precautions. (iii) Steel scaffolfing is to be used in the work. (iv) Necessary arrangement for temporary plug the / door / window / ventilator opening at time of taking down plaster/ new plaster till completion of work. Made by Tender / Contractor at own expense.

KISHORE ENTERPRISES (BID ID -3295037)

sidh builders (BID ID -3300067)