Renovation of Laboratories at Mangattuparamba Campus of Kannur University under PM-USHA Scheme

Amount

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

SPESS LAB

Providing and fixing Over Head Shelves with 18mm thick Pre-laminated medium density fibre board with 4.0mm Sliding glass with necessary locks and railings. Shelves Size shall 90cm Height and 100cm Depth with necessary supports with Hollow Tubes covered with matching 12mm MDF board. Pre-laminated with decorative lamination on both side exterior for medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to backing or studding with screws etc. complete. (Elevation Area to be measured)

EVS Lab

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tiles 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in- charge.

Gas service line work- Multilayer composite Pipe (PE-AL-PE) with Brass fittings for main lines including valves and necessary fittings.

Two tiered reagent racks (MS with powder coating) with granite top of 150 mm depth for side workbenches. The two tier should be placed at a minimum spacing of 300 mm. The item should be in compliance with IS 4209 (2013), NABL etc. The Length should be customized as per lab workbench and vertical posts must be placed at appropriate spacing.

Supply and Installation of Sink Module with Sink Each sink module should have a minimum dimension of 900 mm (L) x 900 mm (W) x 900 mm (H) and made of MS as per IS 1730 shall be designed with a single cabinet (with 2 shutter, SS304 hinges for easy and noiseless opening and closing mechanism). This module should include a sink made of 5 mm thick polypropylene with black color body. Minimum Dimension of the sink: 450 mm (L) x 600 mm (W). Sink should include PVC tap connection-15mm diameter (Goose neck type), grating etc. The sink module shall be portable and provided with 18mm thick granite table top (with cut out for providing sink). Item to be inclusive of all necessary fitting arrangement. The item should be in compliance with IS 4209 (2013), NABL, WHO etc.

Supply And Installation of Lab Workbench Material of Construction: GI as per IS277, Min thickness- 1mm or more (as required based on the design), Finish: Complete module and framework shall be powder coated and provided with suitable finish for maximum corrosion resistance (Colour as per the instruction from the HLL Engineer in charge), Minimum Dimension of Module: 900 mm (Width) x 900 mm (Height) Every one meter of the module shall be designed with min 2 drawers (with SS 304 telescopic channels and lockable drawing mechanism) and a single cabinet (With 2 shutters, SS304 hinges for easy and noiseless opening and closing mechanism), SS304 locks and dual keys arrangement, handles, screws etc. Common Raceways (Powder coated GI with cover) for cabling electrical, network, voice connections with provision for fixing sockets, switch boxes etc. Raceway should be 3 run type.The workbench shall be portable and provided with 18mm granite table top. The item should be in compliance with IS 4209 (2013), NABL, WHO etc. Measurement will be taken in length only.

Supplying fume hood Premium quality student grade fume hood will be provided with traspa brand 6mm phenolicresinliningand 18mm+/- mm thick granite as work table top with Epoxy beading.1nos of remote controlled water and gas faucet and polypropylene cup sink(6x4 inch) will be provided as services .Epoxy scuff hold will be provided for temporary holding purpose. Flurecent/led light will be provided for with extra covering. Powder coated MS blower duct will be provided for fume extraction purpose, which is connected to electric blower through PU blobet flexible hose. An under bench cabin will be provided for chemical storage purpose.

Experimental Lab

Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

Providing and fixing Over Head Shelves with 18mm thick Pre-laminated medium density fibre board with 4.0mm Sliding glass with necessary locks and railings. Shelves Size shall 90cm Height and 100cm Depth with necessary supports with Hollow Tubes covered with matching 12mm MDF board. Pre-laminated with decorative lamination on both side exterior for medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to backing or studding with screws etc. complete. (Elevation Area to be measured)

Wiring

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 8 Module (125mmX125mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Fixtures

Supply, Installation of surface mounted LED Tubelight. The luminaire should have CRI >80 and CCT of both 6500K/5700K. The luminaire shall be compliant with IP20 and IK02 classification. Luminaire shall be designed to emit at least 3600 nominal lumens and efficacy of atleast 105 lumen/watt and Minimum system wattage of 30 Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 25k burning hours. The electronic driver used shall have a power factor >0.95 and THD. Make - Philips, Crompton, Wipro, Havells

Supplying, conveyance and Installation of 150-250 mm sweep,1350 rpm, 3 - 5 blade Exhaust Fan including frames and all mounting accessories complete. Recommended Make: Crompton, Havells, Usha

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, ashers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. Make: Atomberg/Havells/ Orient Electric/ Crompton or equivalent

Supplying and fixing RJ45 Outlet including cover plate, Keystone Jack and Gang box supporting, connection etc. as required

Supplying and fixing suitable size PVC box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supply, Installation of 12 Watt LED Bulb.

Air Conditioning System

Supply, installation, testing and commissioning of Split Air Conditioner of following capacity and specifications: Consisting of high wall-mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of energy-efficient suitable rotary compressor for operation on single- phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation up to 4 m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. (Make: Voltas, Blue Star, Hitachi, Carrier or equivalent). 1.5 TR 3 Star rated (inverter type AC) as per BEE