Constructing new 11 kv feeder from Edappon substation to ITBP jn using covered conductor under Electrical Section Nooranadu

Stringing of one km 3 PH 11kV line with XLPE Insulated ACSR Raccoon

Loading HT PSC pole from the stacking place and unloading the same at work site (transport by vehicle).

Loading HT A type pole from the stacking place and unloading the same at work site (transport by vehicle).

Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 poles excluding loading & unloading.

Dismantling (without damage) one LT PSC/RCC pole after disconnecting stays, strut etc. and stacking the same.

Dismantling one damaged LT PSC/RCC pole after disconnecting stays, strut etc. and stacking the same.

Dismantling (without damage) one 11kV PSC/RCC pole after disconnecting stays, strut etc. and stacking the same.

Dismantling (without damage) one 11kV A type pole after disconnecting stays, strut etc. and stacking the same.

Fitting and erecting one HT PSC Pole in position incl. fitting cross arm, digging & back filling pit, drawing earth leads.

Fitting and erecting one HT A type Pole in position incl. fitting cross arm, digging & back filling pit, drawing earth leads.

Fitting and erecting one HT DP using A type pole in position incl. fitting 2 channel cross arms, digging & back filling pit, drawing earth leads.

Fitting and providing one Strut using HT PSC pole incl. digging & back filling pit.

Fitting and providing one Strut using A type pole incl. digging & back filling pit.

Fitting and providing one HT Stay for 11kV pole incl. digging & back filling pit.

Transferring LT 3ph 4/5 wire OH line to newly erected HT/LT pole and refitting all items to the new pole.

Transferring LT Sph 2/3 wire OH line to newly erected HT/LT pole and refitting all items to the new pole.

Additional rate for refitting/redoing one Shackle set and reshackling one span while renewing any type of pole.

Dismantling and reconnecting Sph service connection from the OH line incl. lowering down the WP portion.

Dismantling and reconnecting 3ph service connection from the OH line incl. lowering down the WP portion.

Dismantling one ordinary street light/CFL/LED fitting from existing pole and refitting the same on newly erected pole and reconnecting.

Providing concrete muffing (0.45x0.45x1.5m) inclusive of cost of all material (as per specification).

Dismantling (without damage) one AB switch from existing structure and bringing back to section store.

Fitting one set AB switch and giving connection

Additional rate for refitting/redoing one Disc set while renewing any type of 11kV cut pole

Providing one Coil Earth using GI earth wire, digging separate pit at standard distance away from the pole/structure & backfilling.

Fitting one Additional V cross arm in existing single pole incl. conveyance of materials.

Fitting one additional HT pin with insulator

Fitting one Additional 75x40mm, 1.8m Channel cross arm in existing single pole incl. conveyance of materials.

Dismantling one Channel cross arm from existing DP structure, and bringing back to section store.

Fitting one Additional 2.4m/3m Channel cross arm (100x50x6mm), in existing 11kV DP incl. conveyance of materials.

Dismantling (without damage) one km 11kV line (3 conductors), cross arm, insulators, disc, rolling the conductor and stacking.

Stringing of one km 11kV line with ACSR Raccoon (3 conductors) incl. cutting and removing tree branches wherever necessary.

Dismantling one section fuse

Fitting one No. Section fuse on LT line with dropping cables, crimping sockets, connecting with bolt&nut etc.

Fiting One no MVT on existing cross arm excluding termination work (for One phase) of any rating for 11 kV AB Cable

Dismantling of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16 (Street Light) + 1 x 50 Sq.mm. (Insulated Messenger)

Stringing of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16+1x 50 sqmm with bare/insulated Messenger through existing poles

Dismantling of Anchor clamp / dead end clamp for LT AB cable

Erection of Anchor clamp / dead end clamp for LT ABC of any size

Dismantling of suspension clamp suitable for LT AB cable

Erection of suspension clamp for LT ABC of any size

Cutting trees beyond 120cm but upto and incl. 180cm girth, cutting of trunks/branches, removing the root completely and stacking.

Cutting trees beyond 60cm but upto and incl. 120cm girth, cutting branches, removing root completely and stacking (where space for falling trees is not enough).

Cutting trees beyond 120cm but upto and incl. 180cm girth, cutting branches, removing root completely and stacking (where space for falling trees is not enough).

Additional rate for providing one disc set on any type of HT pole for making cut point.

Drilling hole of various sizes on existing Channel/Cross Arm.

Excavation of cable trench in all classes of soil and backfilling after laying of cable (excluding laying of cable).

Laying HT XLPE UG cable (of sizes beyond 3x185 sqmm and upto and incl. 3x300 sqmm) as per specification excl. excavation and backfilling.

Doing straight joint on cables of sizes beyond 3x185 sqmm and upto and incl. 3x300 sq mm using the cable jointing kit supplied departmentally as per specification.

Doing one cable end termination on cables of sizes beyond 3x185 sqmm and upto and incl. 3x300 sq mm using the cable jointing kit supplied departmentally.

Painting A pole structure with one coat Synchromate primer and two coat grey enamel/aluminium paint incl. cost of paint.

Providing one Driven Earth using GI earth pipe at standard distance away from the pole/structure in loose soil.