AR and MO Sewerage Scheme to Nagrota Town in Tehsil Nagrota Bagwan

Amount

Excavation in foundation trenches etc. in earth work in all kind of soil lift upto 1.50 meters stacking the excavated soil not more than 3 meters. clear from the edge of the excavation and then soil such as pick Work, jumper work, blasting hard or softs rock by chiselling where the blasting work is prohibited slushy daldal and saturated soil including within all heights, stacking the excavated soil within all leads clear from the edge of excavation and then returning the stacked soil in 15Cm (fifteen Centimetres) layer when required into plinths, sides of foundation consolidating each depossited layer by ramming and watering and then disposing of all surplus excavated earth complete in all respect including all leads and Lifts as per the direction and satisfection of Engineer-In-Charge.

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Providing and laying cement concrete 1:1½:3 (1cement:1½ sand :3graded stone aggrigate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundations, footings bases of columns and the like and mass concrete complete in all respect as per direction and to the entire satisfaction of Engineer- in- charge up to leads and lifts.

In walls (any thickness but not less than 0.10mm thickness) attached Pilasters, buttersses, plinth and string courses etc. from top of foundation level upto floor two level complete in all respect as per the direction and to the entire satisfaction of Engineer-In-Charge with in all leads and Lifts.

Suspended floors,roofs,landings.etc. upto floor two level complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4mtrs.and removal of the same for in-situ-reinforced concrete and plain concrete work in:-

Flat surfaces such as soffits of suspended floor, roof, landings etc complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillasres buttresses,plinth & string courses and the like complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Edges of slab and breaks in floor upto 200 mm thickness complete in all respect including all leads and Lifts as per the direction and to the entire satisfaction of Engineer-In-Charge.

Providing Mild steel /Tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level (tor steel) complete in all respect including all leads and Lifts as per the direction and satisfaction of Engineer-In-Charge.

White washing with lime on un-decorated wall surface two coats to give an even shade including throughly brooming the surface to remove all dirt dust and other foreign matter complete in all respect as per direction and to the entire satisfaction of Engineer- in- charge up to leads and lifts.

Providing, Supplying and fixing of Moving Bed Biofilm Reactor (MBBR) Media: Virgin Poly Propylene, Brand: AB Polymers, Specific Gavity: 0.90-0.95 complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts. (As per technical specification Sr. No.1)

Providing, Supplying and fixing of Silicone Platinum Cured Fine Bubble Diffusers maximum allowable pressure 0.7Kg/cm² complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts. (As per technical specification Sr. No.2)

Providing, Supplying, fixing and Installing of Tube Settler relevant IS code as per BIS specification at the site of STP complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts. (As per technical specification Sr. No.3)

Providing and fixing of aluminium / FRP sheet alongwith frame and allied acessories to maintain quiescent condition at quiescent zone complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts. (As per technical specification Sr. No.4)

Providing and fixing of Twin Lobe Toots Blowe air cooled compressor with 20 HP motor complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts. (As per technical specification Sr. No.5)

Providing and fixing of DI Pipe 200mm dia of reputed make / IS marked complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts.

Providing and fixing of Cast Iron Sluice Valve 200mm dia of reputed make / IS marked complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts.

Providing and fixing of Cast Iron Rungs complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts.

Providing and fixing of Cast Iron Rungs complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts.

Providing and fixing of MCC Pannel capable to run 20 HP twin lobe compressor & motors including Automatic Control Pannel, Main MCB, Voltmeter, Amp Meter, Power Capacitor, Control MCB, Motor side cable, common header, earthing and all other required component complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts. (As per technical specification Sr. No.6)

Providing Steel work welded in built up section trusses and framed work including cutting, hosting fixing in position and applying a priming coat of red lead paint in grating framed guards bars railing brackets and similar works complete in all respect including all leads and lifts.

Providing and fixing of M.S pipe 25mm dia for railling with fitting complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts.

Painting Two coat (including priming coat) on steel and other metal surfaces with enamel paint other then ready mixed paint) with brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter with enamel black paint complete in all respect as per the direction and to the entire satisfication of Engineer-in-Charge with in all leads and lifts.

Providing design of MBBR Unit's (Hydraulic design & structural design along with drawings) duly verified from NIT / IIT/ PEC.

KAILASH DEWAN

SURINDER KUMAR