REPAIR/REPLACEMENT OF FIRING RANGE WORKS, TRAVERSE WALL, SHUTTER AND MISC CONNECTED ITEMS IN MD/OTM ACCN AND E/M INSTALLATION OF ELECT SUPPLY AT GANDHINAGAR MIL STN

Amount

Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete,brick work,masonary etc. any section, including taking out embedded portion and making good disturbed ground

Excavation in post holes each not exc 0.5 cum, getting out soft/loose soil , returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplush soil to a distance n exc 50m and making good surface complete all as directed by Engineer-in-charge and all as specified.

M&L for PCC Type C2 1:3:6 (40 mm graded aggregate) Cement concrete in foundations, filling and mass-concrete complete all as specified & directed by Engr-in-Charge.

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc., flat iron fillets (for securing wire mesh etc) including necessary welding where required as per site requirement and other similar works complete, conforming to Gde E-165 (Fe 290).

S&F mild steel round bars as in tie bars of 10 mm dia and over, fixed to fencing posts including cut to length, bent to shape, welding of bar at spots as directed and other similar works, conforming to Grade E-165 (Fe 290), complete, all as specified & directed. Note: Cost of cutting to length, bent to shape rquired & binding with MS wire is included in above rate.

S&F for Mild steel screw bolts dia of Neck 5mm to 10mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,exc 5cm but n exc 10cm long compleete all as directed by Engr-in-charge.

Dismantling structural steel work including door /gate , frame ,trusses compete all as specified

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plate , rails braces etc. complete drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or slinding with and including either hooks hinges and rollers for slinding gates, guide rail of MS flat and framing required for fixing of rollers, pintle hinges, locking arrangement as required and hanging also fastening and fixing complete using Fe- 290 (Gde E-165) quality 'A' compleete all as directed by Engr-in-charge.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as directed by Engr-in-charge.

S&F framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc complete all as directed by Engr-in-charge.

S&F Framed work for ornamental and intricate design complete all as directed by Engr-in-charge.

Dismantling timber scantlings unframed 40 sq. cm and over in section, in any position

M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 Complete all as specified

M&L painting to new or previously untreated steel surfaces of any description over 10cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chromic primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of nwely/existing steel surface to received painting by coating with mordent solution including washing and cleaning etc over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. Note : The rate quoted by tenderer is deemed to included in item for painting any type of Rolling shutters and any type of doors including any height and width at Mil Stn Gandhinagar shall be made good by contractor without any extra cost to the Govt.

Dismantling of fencing wire mesh,any type complete all as specified and directed.

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.incl provission of binding wire.

S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Restraining & resecuring the old Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed including making good stable etc complete all as specified and directed.

Restraining & resecuring the old chain link fencing including making good stable etc complete all as specified and directed.

M & L pre stressed pre cast RCC (M-25 grade) column cross section 150 mm x 150 mm with contineous vertical grooves of size 60 mm x 35 mm at two sides of column to receive the precast panels including reinforced with 7 nos wires of 3 mm dia high tensile corbonized steel surfaces finished even and smooth including errecting in position all as specified and as directed incl taking down of old column from sub base PCC complete all as specified and directed.

M&L pre stressed pre cast RCC (M-25 grade) panels of cross section of panel (300X45 mm) reinforced with 4 nos wires of 3 mm dia high tensile corbonized steel, including fixing in position in between column grooves and jointing and flush pointing of all horizontal and vertical joints of panels with cement mortar 1:3 complete all as specified and as directed incl taking down of old Panel complete all as specified and directed.

Cleaning of storm water drains, inside/outside cleaning by rough excavation not exceeding 1.5 M deep and getting out in soft/loose soil including cleaning away all grass vegetation, saplings, shrubs bush wood of under growth roots removing excavated material and obtained from cleaning to a distance not exceeding 50 Meter from outside the periphery of the area under clearance depsoiting the same in low laying area.

M & L Pre cast RCC (M-25 grade) louvres and jallies, 25-30mm thick set in cement mortar 1:4 (measured solid) , including all mouldings complete and design /pattern decided by Engr-in-Charge.

M & L Pre cast RCC (M-25 grade) louvres and jallies, 35mm thick set in cement mortar 1:4 (measured solid) , including all mouldings complete and design /pattern decided by Engr-in-Charge.

Dismantling/Demolition/Chipping carefully loose/distressed portions of reinforced cement concrete to a depth or thickness varying from 10 mm to 100mm (reinforcement cut as required to facilitate demolition) work by means of sharp chisel, low impact hamer without damaging existing strong concrete upto the suitabale depth of unsound concrete in beams, roofs, chajjas, columns, staircase, landing, parapets, soffits of slabs and similar suspended work etc incl disposal of broken material/malba to the distance of 50m complete all as specified and directed. Notes :- (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Removal of damaged concrete and surface preparation: M&L for Surface preparation including removal of all loose particles, plaster, tiles, laitance, dust, curing compounds, floors hardeners, oil, grease, fat, bitumen and paint, other fixtures etc. Removal of existing affected, distressed, loose cover concrete including loose damaged concrete from RCC lintel bend, Column up to beyond the corroded steel reinforcements to a depth of 10 mm minimum behind the reinforcement only at affected concrete (Good & sound concrete should not be chipped / damaged) by chipping / hacking with chisel and hammer or by mechanical means like light weight chisel hammer, pneumatic chippers, making saw cut at periphery to avoid feather edge and removal and disposal of debris at designated location within plant premises including labour, tools, electricity, plant and machineries etc. complete as directed by Engg.in charge. Depth of chipping may vary upto 100 mm. Cleaning of rust/ scales/corrosion from reinforcement bars using high pressure water jetting etc. complete. (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Reinforcement Rust Removal & Corrosion Protection: M&L for Cleaning as directed & specified all corrosion / rust / scales from reinforcement bars using rust remover ShaliRust Off from STP Ltd or Equivqlent leaving to dry for 30 mins & washing surface with fresh water as required to exposed reinforcement bars complete as specified also providing & applying inhibtion coats/system to exposed reinforcement bars after drying & also new bars after cleaning & removing scales and rust completely as specified. Two component inhibitor coating ShaliPrime Zn primer of STP Ltd or equivqlent. make as approved by engineer shall be used as per manufacturers specification in two coats including all labour tools tackles, necesary surface preparation complete all as specified and directed (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Additional Reinforcement: M&L for cutting, fabricating new reinforcement for providing additional steel reinforcement to compensate corroded reinforcement in existing member etc. and fixing with old existing reinforcement which was reduced by 20% or more of its original diameter as required as provided in original structure and additional steels as directed by EIC as required welding or tying with 16 gauge annealed binding wire complete as per specifications and as directed by EIC. (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Epoxy bond coat on old concrete: M&L for Providing and applying one bond coat on the prepared surface to receive new polymer mortar/polymer modified concrete, with two components epoxy based bonding coat ShaliBond Concrete of STP Ltd. in one full coat. Laying of reinstatement polymer mortar or micro concrete shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete. Item rate is inclusive of the meterials all labour, supervision, tools and tackles and transportation etc. complete as per specification and as directed. (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Shuttering: Providing & fixing and removing leak proof Shuttering of Plywood Or Steel for micro concrete /RCC work at all levels with necessary supporting system to keep the shuttering in position during pouring of Microconcrete. Rate includes all material, labour for fixing, removing and keeping in position till the setting of Micro concrete and removing the shuttering. (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Microconcrete Reinstatement and jacketting for lintel / Columns/Beams/Facia /Chajjas/ Roof Projections: Providing and laying of special repair material micro-concrete, for jacketing of Columns using single component, shrinkage compensated, high strength, high flow cementitious micro-concrete having compressive strength minimum of 50 N/mm2 at 28 days such as ShaliFix MC of STP Ltd or equivalent, blended with washed saturated surface-dry (SSD), graded aggregates of size 3mm to 10mm at 50% by weight of micro concrete (if thickness is 100mm or more) and water as per data sheet and pouring into the shuttering by hopper type form work using suitable arrangement for uniform flow of Microconcrete. The side shuttering can be removed after Minimum of 24 hours, preferably 3 days and the bottom shuttering after 7 days ensuring proper bond between the micro concrete and existing concrete substrate. (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates. (iii) Shuttering, steel reinforcement shall be paid in other relevant items measured and paid saperately in respective items

External Cement plaster: Providing and applying 15mm thick plaster using CM (1:3) for 1st coat and (1:2) for second coat including waterproofing admixture such as ShaliPlast IW of STP Ltd or equivalent @ 150 ml per 50 kg of cement etc. complete. (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Protective coatings for Enviornmentally exposed external surfaces: Providing and applying an elastomeric membrane forming system with anti-carbonation and breathing properties, the system, ShaliKote AC WB with Primer, of STP Ltd or equivalent, based on water based acrylic/acrylate polymers. The system consists of one coat primer (ShaliPrime AC WB) over prepared surface and polymer coating (ShaliKote AC WB) to give film thickness of 200 – 225 microns for two coats depending on method of application and smoothness of concrete surface. Surface Preparation should include grinding or wire brushing and removal of all loose particles, dust, oil and other contaminants. For smooth surface finishes, final preparation should include filling of all bugholes / uneven surfaces in the concrete, using suitable putty or equivalent. Polymer coating should be in suitable approved shades, including suitable surface preparation as described above, cost of materials and labour for applying the above coating, etc. (i) Work to be carried out in patches. (ii) The rates for scaffolding system to be used upto 15 mtr workable height shall be deemed including in the above rates and no extra shall be paid over & above the quoted rates.

Providing and laying 75mm thick for precast SFRC drain cover without frame but including complete sides iron sheets (medium ) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 3 to 4 ton /Sqm in circular , square or rectangular shape complete all as specified and directed by Engr-in-Charge. Note :- All Reinforcement and iron sheet including formwork,concrete complete the rate quoted by tenderer is deemed to included in item shall be made good by contractor without any extra cost to the Govt.

M&L for Reinforced cement concrete (nominal mix) in Type B1 1:2:4 (20 mm graded stone aggregate) RCC lintel/Column/ beam/ Slabs/walls /floors/ roofs, landings,chajjas/shelves/ balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge. Note :- Reinforcement shall be measured and paid for separately.

M&L for TMT bars for main bar and stirrups,binders, spacers bar 8mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bar complete all as specified and directed by Engr-in-Charge.

Demolition of brick/stone masonry or PCC coping built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified & directed.

M&L for Brickwork with subclass ‘B’ bricks, (OLD SIZE BRICKS) straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, (OLD SIZE BRICKS) (Except bricks) straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm gradded stone agg )as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, drain channels, copings,parapets copings, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed.

M&L for cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in surface channels and drains and benching including finishing the top of benching complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm gradded stone agg )as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, drain channels, copings,parapets copings, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed.

Supply only integral liquid water proofing compound (ISI marked) complete all as specified and directed.. Make : Pidilite (Dr. Fixit Pidiproof LW) or equivalent of Fosroc / Sika / STP

Taking down shutter of any description exceeding 1 Square Metre and not exceeding 2 Square Metre each complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 Square Metre and not exceeding 04 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 35mm thick IInd class hard wood panelled door shutter with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete.

S&F 35 mm thick IInd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats complete all as specified and directed.

M&L for Factory made flush shutter 35mm thick solid core construction with block board core and ply wood face panels, commercial type on both side and covered with decorative face veneer both side with lipping/frame to match incl polish etc compete all as specified and directed by Engr-in-Charge.

M&L for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions), slinding windows, rollers, with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for aluminium door shutters, aluminium section weighing 0.55 kg/m, with power coating (minimum thickness 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m,with power coating (minimum thickness 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

S&F providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F anodized aluminium grill with power coating (minimum thickness 50 micron) of approved pattern and fixed to the existing window/ventilator frame with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement & directed by Engr-in-Charge.

Supply only mild steel TMT bars, upto 10 mm dia.(Fe 500 D) for rein forcement against item No 26 & 27 here above complete all as specified and as directed.

M&L for preparing of new untreated wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint (of approved shade) over a coat of pink primer all as specified.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floors/walls in PCC 1:2:4 type B-0 to match the existing floors/walls.

S&F 1mm thick laths Steel rolling shutters, with out ball bearing, as specified including top cover,guide rail ,anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified

S&F 1mm thick laths Steel rolling shutters, with out ball bearing, as specified including top cover,guide rail, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: gear operated type with level gear box and crank handle complete all as specified

Supply and fixing stainless steel hinges 100mm long medium weight to pressed steel/angle iron frames by welding/screws all as specified.

S&F aluminium anodised barrel tower bolt 150mm size extruded section, ISI marked & fixed

S&F extruded aluminium alloy handles 150mm size fabricated type anodised. ISI marked.

M&L for Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of top to vertical surfaces complete all as specified & directed by Engr-in-Charge.

Supply only 4mm thick Sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane all as specified and directed by Engr-in-Charge

Supply only 4mm thick Sheet glass, ordinary quality, in squares exc 0.5 sq. m each pane all as specified and directed by Engr-in-Charge

Supply only 4mm thick tinted Coloured glass fixed to metal frame complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & scrwed complete all as specified and directed

Dismantling of wall and ceiling boards/ wall penelling/lining (fibre, pulp, insulation etc) of any thickness, complete all as specified and directed.

M&L for false ceiling made out of E-board classic of size 595 x 595 x 4 mm thick, (as approved by GE) fixed with existing frame work fixing the board to frame complete all as per manufacurers instructions all as directed and specified.

Dismantling Wall and ceiling boards including framework (PVC penelling incl fillet, fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specifiedand directed

M&L for non asbestos fibre reinforced designer cement board false ceiling made out of E-board classic of size 600 x 600 x 4 mm thick, GI frame consisting of main Tee of size 38.50 x 24.00 mm and cross Tee of size 28.50 x 24.00 mm thick made out of PGI sheet 0.30 mm thick doubled at web and single at flange, flange covered with powder coated sheet 0.25 mm thick and angle 24.00 x 24.00 x0.4 mm thick powder coated suspended with GI wire 3 mm dia and up to 2 Mtrs long complete including plugging fixing of angle to brick walls with steel rawl plugs @ 450 mm c/c all as per manufactures instructions etc complete all as specified and as directed

Taking down cement plaster of any description, thickness and in any position including raking out joints, hacking for key, scrubbing down with water etc , including making good damaged/hungry joints in cement mortar 1:3 mixed with WPC (Liquid type of Dr Fixit) complete as directed.M&L for preparation of exposed brick wall surface by cleaning the surface with wire brush to remove all dirt/loose materials from the bricks and from the joints between the bricks. Prepared surface should be then washed with diluted HCL acid (dilution ration of 1:50) for three times in a day for two days. After acid wash surface should be allowed to be air dried for one day. complete all as specified and as directed. Note : Further treatment over the surface so achieved will be carried out only after approval of the same by Engr-in-Charge.

Taking down plaster in cement mortar over walls/ceiling including racking out joints & hacking for keys.

M&L Rendring 10mm thick in CM 1:6 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement all as specified.

M&L Rendring 12mm thick in CM 1:4 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 12mm thick in cement mortar 1:4 on other than fair faces of brick masonry or concrete surfaces of walls, mixed with water proofing admixture (ISI marked), finished even & smooth without using extra cement complete all as specified. Note : - Supply only water proofing admixture shall be measured and paid for separately.

M & L for internal/external plaster/unplastered newly/old surfaces on walls/ceilings and preparation of surfaces of walls/ceilings and applying wall/ceiling putty of 1mm thick complete all as specified and directed by Engr-in -Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

Material and labour for preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed

Material and labour for preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of old surfaces of walls and applying one coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for preparation of old decorated surfaces of walls and applying two coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for preparation of old decorated surfaces of walls, plastered including cornices, pilasters etc and applying one coats of white wash complete all as specified.

M&L for preparation of old decorated surfaces of walls, plastered including cornices, pilasters etc and applying two coats of white wash complete all as specified.

M&L for preparation of old decorated plastered/unplastered surfaces of ceilings & applying one coats of white wash complete all as specified..

M&L for preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

M&L for complete removal of loose concrete & demolition of RCC, if required, upto 100mm thick as in facias, chajja, parapet, roof projection etc, taking out/cutting degraded/rusted reinforcement.Fixing of MS TMT bars upto 10mm dia including cutting binding & welding to the existing reinforcement. Recasting of facia, chajjas, roof projection, parapet etc using RCC (1:1.5:3) type AO using 12.5 mm graded stone aggregate including necessary formwork complete all as spd & directed. Note:- 1. Supply only TMT bars shall be paid under Ser Item No 59 2:-Repair to facia chajjas,parapet,lintel projection, coping & roof projection etc against this item will be carried out at any height 3:-Epoxy primer @0.50 Kg/sqm (fosrock shall be applied at junction of old & new concrete. 4:-Recasted portion of facia,chajja,parapet,roof projection etc shall be plastered in CM 1:3 and cement base paint/exterior emulsion shall be applied over primer to match with the exiting surface. Cost of this is deemed to be included in this Item

M&L for complete removal of loose concrete & demolition of RCC, if required, upto exc. 100mm but n.exc 150mm thick as in facias, chajja, parapet, roof projection etc, taking out/cutting degraded/rusted reinforcement.Fixing of MS TMT bars upto 10mm dia including cutting binding & welding to the existing reinforcement. Recasting of facia, chajjas, roof projection, parapet etc using RCC (1:1.5:3) type AO using 12.5 mm graded stone aggregate including necessary formwork complete all as spd & directed. Note:- 1. Supply only TMT bars shall be paid under Ser Item No 59 2:-Repair to facia chajjas,parapet,lintel projection, coping & roof projection etc against this item will be carried out at any height 3:-Epoxy primer @0.50 Kg/sqm (fosrock shall be applied at junction of old & new concrete. 4:-Recasted portion of facia,chajja,parapet,roof projection etc shall be plastered in CM 1:3 and cement base paint/exterior emulsion shall be applied over primer to match with the exiting surface. Cost of this is deemed to be included in this Item

M&L preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified.

M&L for preparation of old decorated surfaces of walls, plastered including cornices, pilasters etc and applying one coats of weather proof exterior emulsion paint complete all as specified.

Taking down existing unserviceable rolling shutter complete of any size and any type and removing from site complete all as specified and directed.

S&F, in repairs, in rolling shutters top cover fabricated to required shape and size made out of 1.00 mm (20 gauge) thick M S sheet including necessary fixtures and fastening with one shop coat of redoxide primer for length upto 3.00 mtr complete all as specified and directed.

S&F, in repairs, in rolling shutters top cover fabricated to required shape and size made out of 1.00 mm (20 gauge) thick M S sheet including necessary fixtures and fastening with one shop coat of redoxide primer for length upto exc 3.00 mtr but n. exc. 5.00 mtr complete all as specified and directed.

Repair of old unservicable/jam steel gates of any size by welding, greasing and making servicable by fixing of loose/broken flat iron side clamps to any type of wall ,pillar etc. with and incl flat iron necessary welding work with stainless steel fasteners.

S&F, in repairs, Gear box assembly for rolling shutter including rod, required nuts, bolts, cleats, crank handle etc. complete of standard make and fixed in position including one coat of primer including removal of old gear box assembly and other accessories all as specified and directed.

Taking down steel rolling shutter push pull or manual type including top hood cover anchoring rod, hasp and staple etc and refixing same in position after necessary repairs such as cleaning,replacement of rusted nuts and bolts with required / welding grinding and all moving parts,guide rail including greasing the guide rail gear worm, gear box ,adjusting anchoring rod, straining tensile spring etc as required to make rolling shutter fuctional and making good any damage to the area of shutters n exc 5 Sqm but n exc 10 Sqm each complete all as specified and directed.

Taking down steel rolling shutter push pull or manual type including top hood cover anchoring rod, hasp and staple etc and refixing same in position after necessary repairs such as cleaning,replacement of rusted nuts and bolts with required / welding grinding and all moving parts,guide rail including greasing the guide rail gear worm, gear box ,adjusting anchoring rod, straining tensile spring etc as required to make rolling shutter fuctional and making good any damage to the area of shutters n exc 10 Sqm but n exc 20 Sqm each complete all as specified and directed.

Taking down steel rolling shutter gear operated type with lever gear box and crank handle including top hood cover anchoring rod, hasp and staple etc and refixing same in position after necessary repairs such as cleaning,replacement of rusted nuts and bolts with required / welding grinding and all moving parts,guide rail including greasing the guide rail gear worm, gear box ,adjusting anchoring rod ,straining tensile spring etc as required to make rolling shutter fuctional and making good any damage to the area of shutters n exc 5 Sqm but n exc 10 Sqm each complete all as specified and directed.

Taking down steel rolling shutter gear operated type with lever gear box and crank handle including top hood cover anchoring rod, hasp and staple etc and refixing same in position after necessary repairs such as cleaning,replacement of rusted nuts and bolts with required / welding grinding and all moving parts,guide rail including greasing the guide rail gear worm, gear box ,adjusting anchoring rod ,straining tensile spring etc as required to make rolling shutter fuctional and making good any damage to the area of shutters n exc 10 Sqm but n exc 20 Sqm each complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B.

M&L for 75 mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base complete all as specified& directed by Engr-in-Charge.

M&L for 100 mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base complete all as specified& directed by Engr-in-Charge.

M&L for 40mm thick PCC Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in flooring complete all as specified and directed.

M&L for 75mm thick PCC Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in flooring & alternate panel (2.5mtr X 2.5mtr ) including power floater conncrete machine vibrater with filling bitumen etc. including necessary form work complete all as specified and directed by Engr-in -Charge. Note :- Bitumen gola, with 80/25 bitumen and coarse sand mortar 1:3 shall be measured and paid separately under respective items.

M&L for Glass dividing strips, 3mm thick, 38mm depth and inserted in position to conform to design complete all as specified & directed by Engr-in-Charge.

S&F 0.56mm thick Plain Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing length and girth as fixed with coach screw and Aluminium washer in roof and wall etc. fixed with self tapping screws complete all as specified and directed by Engr-in -Charge.

Providing and laying prepolished cement concrete Chequered tiles 30cmx30cmx25mm thick, with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape heavy duty , set,jointed and pointed in neat cement slurry in floors over screed bed 15mm thick 1:6 cement mortar complete all as specified & directed by Engr-in-Charge.

Dismantling floor tiles/stone, hearth or wall tiling/kerb stone including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises

M&L for sand filling under floor or in foundation including spreading & ramming and levelling in layer not exc 25cm thick complete all as specified.

M&L for except interlocking paver block any shape and size of 60 mm thickness complete all as specified.

M&L for except interlocking paver block any shape and size of 80 mm thickness complete all as specified.

M&L for 16-18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 10mm thick rendering CM 1:3 complete all as specified & directed by Engr-in-Charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed by Engr-in-Charge.

M&L for vitrified ceramic tiles 8 to 9mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar 1:4 complete all as specified and as directed.

M&L kota stone slab 10-15 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over rendering back of tile 10 mm CM 1:4 complete all as specified& directed by Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Dismantling Plain or corrugated aluminium/steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.

M&L Pre- painted galvatume aluminum zinc coating GI based Semi-corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, roofs,fixed with self tapping screws or L-type or J-type or cranked hook bolts as specified.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Demolition of cement concrete (un-renforced) in ground floor and paving not exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as directed by Engineer-in-charge and all as specified.

Dismantling of cast iron, PVC or reinforced concrete drain pipes including fittings ,jointed in cement mortar upto 110mm and 75mm bore of pipe from wall/floors etc complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack 'Z' clamp complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including 'Z' clamp complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F, 75mm bore PVC (SWR) junction single, (Single T) equal or unequal

S&F, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal

S&F, 110mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F, 110mm bore PVC vent cowl complete all as specified and directed.

S&F in repair PVC (SWR) nahani trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete fixed all as specified.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed by Engr-in-Charge.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed by Engr-in-Charge.

Supplying and laying of 20mm outer dia CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings in trenches complete all as specified.

S&F for CPVC PIPE OUTER DIA 20MM Brass Elbow (3/4 X ½) complete all as specified and directed

S&F for CPVC PIPE OUTER DIA 20MM Brass Male Brass Threaded Adaptor complete all as specified and directed

Taking up or down 20mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

S&F 20mm GI tubing Medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

Taking up or down 25mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

S&F 25mm GI tubing Medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

Taking up or down 40/50mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

S&F 40mm GI tubing Medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

S&F, in repairs, GI Pipe “light grade for rolling shutter for smooth functioning, of old rolling shutter and removal of old pipe From site all as directed of size 40 mm bore complete all as specified and directed.

S&F, in repairs, GI Pipe “light grade for rolling shutter for smooth functioning, of old rolling shutter and removal of old pipe From site all as directed of size 50 mm bore complete all as specified and directed.

M& L for Cutting chases, pinning in, for brick walls, making good to facings for concealed water tubing etc. cutting exceeding 10cm but not exceeding 20cm girth complete all as specified and directed.

S&F in repairs 15/20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed , minimum weight - 210 gms of including taking down existing ball valves any type all as directed by Engr-in-Charge.

Demolition of old existing unserviceable Indian type WC and S&F vitreous china squatting pan of pattern 'long pan' size 580mm white (ISI marked) with 'P' or 'S' trap, front or back inlet and foot rest any pattern, including connection to flushing pipe anti-syphonage pipe etc, including setting of pan & trap in lean PCC 1:5:10 complete and making good to distrubed floor with PCC or cement mortar 1:3 to match with sorroundings all as directed.

S&F in repairs vitreous china wash basin white of size 550x400mm (ISI marked) flat back or angle back type excluding taps, waste chain & plug but incuding cast iron brackets and cutting for and pinning in ends of brackets or erecting stand complete fixed in repairs all as specified and directed.

S&F 32mm dia waste fitting (waste coupling) brass chromium plated for glazed ware sink, basin etc with long screwed shanks and fly nuts flange complete for the following sizes all as directed by Engr-in-charge

S&F Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore all as specified

S&F in repair towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to all as directed by Engr-in-charge

Supply and fixing in repair 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

S&F in repair 32mm dia waste fitting (waste coupling) brass chromium plated for glazed ware sink, basin etc with long screwed shanks and fly nuts flange complete for the following sizes all as directed by Engr-in-charge :-

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, fixed in repairs, complete all as specified.

S&F in repairs PVC connection of 15mm bore with 2 Nos. PTMT nuts, 60cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge.

S&F in repairs long body Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore all as specified including taking down existing pillar tap and removing the same to store.

S&F in repair fancy type long body bib tap cast copper alloy with crutch or butter fly handle 15mm bore chromium plated fixed

S&F in repair bib tap standard of PTMT any colour 15mm bore high pressurescrewed for iron pipe fixed (Min. wt 90 gms) complete.

S&F in repair fancy type angle cock/Stop valves, 15mm bore cast copper alloy,screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F in repair Stop valve of 15 mm dia PTMT any colour high pressure screwed for iron pipe and fixed complete

S&F in repair shower rose size 100mm x100mm , PVC suitable for 15mm bore pipe with swiveling joints complete all as specified

Hacking out old broken glass of any thickness/size of any description from steel / aluminium frame fixed with clips and putty all as specified and as directed.

S&F for 3mm thick ordinary sheet glass fixed with clips and putty completed in squares not exc 0.50 Sqm each pane all as specified and as directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed tinned tacks or GI wire stampe and including wooden beading or nails and screws fixed

S&F in repairs door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked), fixed in repairs, complete all as specified & as directed.

Supply and fixing in repairs brass mortice lock, vertical type, size 100mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified.

DIGNATION ENTERPRISE (BID ID -3328602)

Ramdev and Sons (BID ID -3329089)

ALBA AC AND REF SERVICES (BID ID -3329407)

M/s Bombay Novelty Stores (BID ID -3328654)

r s corporation (BID ID -3325845)

Priya Construction co. (BID ID -3327050)

Abhishek Enterprises (BID ID -3328637)

ARTI CONSTRUCTION (BID ID -3329321)