Establishment of EV Charging Stations with Parking Sheds, CCTV Surveillance, External Lighting and Allied Infrastructure Works Including Associated Civil, Electrical and Furnishings at IISER Tirupati Campus, Yerpedu

SITC of 30 kW DC Fast charger (200-1000V DC) pole/ wall mounted EV charging station having following features etc. as required. • Input Voltage (VAC): 3-Ph 400V (+/-10%) • Efficiency (%): >94% • Input Frequency (Hz): 50 Hz (+/-1.5 Hz) • Input Current: (A AC): • Standby Power: 40W • Power Factor: >98 • Number of Outputs: 1 • Output Connector type: IEC 62196-3 (CCS-2) • Output Voltage (V): 150-1000V DC • Max. Output Current (DC): Max. 100A DC • Max. Output Power Rating (kW): Max 30 kW DC • Display: 7" TFT Color Touch Screen • User Authentication: RFID / Mobile App based • Charging Mode: IEC 61851-1 (Mode-4) • Compliance: AIS138 / IS17017-1 / IEC61851-1 • Charger Interface: LAN / 4G / Wi-Fi • Protections: Input Over Voltage, Input Under Voltage, Input Short Circuit, input over Current, Connection Abnormality, Emergency Stop, Surge Protection up to 4KV, Residual Leakage Current30mA, Ground Fault, Earth Presence Monitoring, Output Over Current, Over Temperature (Derating/Shutdown), Insulation Resistance • Monitoring Reverse Battery Connection • Ambient Temperature: -20° to +55° C (derating from +55'C to +65'C) • Ingress Protection: IP54 • Enclosure Protection: IK10 • Charging wire length: 5 Mtr • Memory Storage to store 50 event logs. To store last 50 charging session information • Application: 4W, Buse • Warranty: 3Years (Comprehensive) • Installation Type: Wall/pole mounting

Providing CMS software integration services for one time etc. as required

Providing services of Control monitoring solution (CMS) subscription for per year per charger etc. as required.

SITC of 7.4 kW AC charger (Commercial Model) pole/wall mounted EV charging station having following features etc. as required. • Input Voltage (VAC): 1 Ph 230V AC (+/-10%) • Output Voltage (VAC): 1 Ph 230V AC (+/-10%) • Max. Output Power Rating (kW): 7.4kW • Screen: 4.3" TFT Color Touch Screen • User Authentication: RFID • Charger and Vehicle Communication PWM as per IEC 61851-1/ IS 17017 • Charger Interface: LAN / GSM / WIFI • Place of Installation: Indoor/Outdoor • Ingress Protection: IP55 • Efficiency (%): >99.9% • Input Frequency (Hz): 50 Hz (+/-1.5 Hz) • Standby Power: 15W • Number of Outputs: 1 • Output Connector type: IEC 62196 TYPE-2 AC • Output Voltage (V): 230V • Max. Output Current (AC): 32A • Charging Mode: Mode-3 as per IS17017-1/ IEC 61851-1 • Charger and Vehicle Communication PWM as per IS17017-1/ IEC61851-1 • Compliance: AIS138/ IS17017-1 / IEC61851-1 • Protections: Input Over Voltage, Input Under Voltage, Input Short Circuit, input over Current, Connection Abnormality, Emergency Stop, Surge Protection up to 4KV, Residual Leakage Current, Ground Fault, Earth Presence Monitoring, Output overcurrent, Reverse Battery Connection • Ambient Temperature: -20° to +55° C (derating from +55°C to +65'C) • Enclosure Protection: K10 • Warranty: 3Years (Comprehensive) • Charging wire length: 5 mtr.

Providing CMS software integration services for one time etc. as required.

Providing services of Control monitoring solution (CMS) subscription for per year per charger etc. as required.

SITC of 3.3 kW AC charger (Single gun) pole/wall mounted EV charging station having following features etc. as required. • Input Voltage(VAC): 1-Ph 230V (+/- 10%) as per IS12360 • Output Voltage (V): 1-Ph 230V AC • Max. Output Power Rating (kW): 3.3Kw • Electrical metering: To comply with IEC 62052-11 & IEC 62053-21 • Number of Outputs: 1 No. • Output Connector Type: 15A Domestic Socket / IEC 60309 • Output Rating: 3.3kw • User Authentication: RFID/Mobile App Based • Metering and billing: Compatibility/ Provision for grid responsive metering QR code OTP/RFID card/APP server based online payment. • Charging operation: RFID card/Scan code/App based authentication. • Interface: Wi-Fi/4G/Ethernet • Ambient Temperature: -20° to +55° C (derating from +55'C to +65'C) • Ingress Protection: IP65 • Enclosure Protection: K10 • Warranty: 3Years (Comprehensive) • Installation Type: Wall/pole mounting

Providing CMS software integration services for one time etc. as required.

Providing services of Control monitoring solution (CMS) subscription for per year per charger etc. as required.

Supplying of following sizes of PVC insulated and PVC sheathed/ XLPE copper conductor armoured cable of 1.1 KV grade confirming to IS:7098 (Part-I) 1988 with upto date amendments duly ISI marked complete as required.

3.5 C x 50 Sq. mm

3.5 C x 25 Sq. mm

4Cx10 sqmm

Supplying of following sizes of PVC insulated and PVC sheathed/ XLPEAluminium conductor armoured cable of 1.1 KV grade confirming to IS:7098 (Part-I) 1988 with upto date amendments duly ISI marked complete as required.

3.5x300 Sqmm (ESS-2 to Green House panel)

3.5x150 Sqmm (From WTP Electrical panel to DEC Shed Outdoor Panel)

3.5x120 Sqmm (From WTP Electrical panel to DEC Shed Outdoor Panel)

3.5x70 Sqmm (From A Block Hostel to UPS Room-A Block)

4core x 10 Sqmm Cable

3core x 6 Sqmm Cable

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 300 sq. mm (70mm)

3.5x150 Sqmm (57mm)

3.5x120 Sqmm (57mm)

3.5x70 Sqmm (57mm)

3½ X 50 sq. mm (32mm)

3½ X 25 sq. mm (28mm)

4 X 10 sq. mm (25mm)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing Hume/RCC/HDPE/DWC pipe etc as required.

upto 35 sq.mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

120mmdia (OD-120mm&ID-103mm nominal)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in cubicle panel board including providing panel board drilling holes in cubicle panel, making connections, etc. as required.

200 A,36KA, FPMCCB

32 A,36KA, FPMCCB

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I earth plate 600mm X600mmX6mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt as required.

Earthing with copper earth 50mm Outer Dia X 3 MTR LENGTH 1.8MM thick copper pipe Completely filled with super Conductive Crystalline Compound fitted with 25X3X3000mm pure coper strip and 32X6X200mm pure copper terminal TIRUMALA High grade Advanced Earthing Compound (NABL TESTED ) Eco Friendly Maintenance Free Earthing Compound to enhance Soil Conductivity Packed in Eco-Friendly HDPE Laminated Paper Bags.25Kg X 3 per Bag per pit including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 3 metre long etc.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 6SWG GI wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying and fixing of follwing size and model 9 watts bolloard light luminaire with reduced glare having opal PC diffuser, symetriccal light distribution, bottom flange mounted, IP 65 with luminaire efficacy of 85 Lumen / watt, colour rendering Index (CRI) of ≥ 70 and co-related colour temperature of 3045 K (+175K), The luminaire should have built-in 4 KV surge protection, PF 2 0.95, and Toal Oty harmonic distortion of THD ≤ 10% impact resistant near ≥ IK07 standard, voltage range of 140-270 V. (The fitting shall be guaranteed for the 5 years on site) including RCC pedastal, connection & loop earthing, testing and commissioning etc. as required. Similar to Signify (Philips) BW100 or equivalent

Brush Less Direct Current (BLDC) Fan with Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)

Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.

Supply, installation, testing and commissioning of 150 mm sweep Exhaust fans 38W capacity with 1350 RPM including all accessories suitable for single phase 240 volts 50 Hz AC supply, complete as required.

Supply, installation, testing and commissioning of 250 mm sweep Exhaust fans 40W capacity with 12700 RPM including all accessories suitable for single phase 240 volts 50 Hz AC supply, complete as required.

OUTDOOR FEEDER PILLER

Supplying, installation, testing and commissioning of floor mounted Outdoor type cubicle panel of following size made out of 2mm thick CRCA sheet for frame work and covers, compartmentalised, dust and vermin proof, hinged doors withknobs 3mm thick gland plate i/c cleaning and finishing with 7 tank process for powder coating in approved shade, 400 amps capacity TPN aluminiumbus bars of high conductivity and all connection to individual circuits from the busbar ,DMC/ SMC bus bar supports and necessary cable supports for clamping the cable in the cable alley, bottom base channel of size 75mmx40mmx5mm, G.I earthbar of size 25mmx5mm at the rear for the entire width of the panel with 2Nos. earthstuds, connections from busbar to switchgear and control wiring with required size FRLS PVC insulated copper conductor cable of suitable size, separate gland plate for each cable entry gland plates including providing and fixing the following switchgear, as per attached specifications and confirming to the CPWD general specifications Part-I (Internal),Part-II (External) &Part-IV (Substation) as amendedup to date complete, as required. Panel size not less than 1450mm(H)x1575mm(W)x450mm(D) INCOMING a) 320 A, 36KAbreaking capacity( Ics) 4 pole MCCB with Microprocessor release- 1 No. BusBarChamber: 4 Strip aluminium bus bars of 400 Amps capacity b) Multi-function meter of 3phase 4wire, 5A Class1 FM with RS485-1No. c)3Nos.LED Phase Indication Lamp d) 6 Amps control MCB- 3No's. e) 320/5AC.Tcoil OUTGOING a) 250 A, 4P, 36KA MCCB Micro Processor based with spreders and rotary handles-01 No. b)200A,4P,25KAMCCB,TMR with spreders and rotary handles- 1No's. c)125A,4P,25KA MCCB,TMR with spreders and rotary handles -1No's. d)63A,4P,10KA MCB -3No's. (Note: The scope of work includes installation of above panel on suitable brick/CC pedetals or suitable angle frame work complete as required.)

Supplying, installation, testing and commissioning of floor mounted Outdoor type cubicle panel of following size made out of 2mm thick CRCA sheet for frame work and covers, compartmentalised, dust and vermin proof, hinged doors withknobs 3mm thick gland plate i/c cleaning and finishingwith 7 tank process for powder coating in approved shade, 300 amps capacity TPN aluminiumbus bars of high conductivity and all connection to individual circuits from the busbar ,DMC/ SMC bus bar supports and necessary cable supports for clamping the cable in the cable alley, bottom base channel of size 75mmx40mmx5mm, G.I earthbar of size 25mmx5mm at the rear for the entire width of the panel with 2Nos. earthstuds, connections from busbar to switchgear and control wiring withrequired size FRLS PVC insulated copper conductor cable of suitable size, separate gland plate for each cable entry gland plates including providing and fixing the following switchgear, as per attached specifications and confirming to the CPWD general specifications Part-I (Internal),Part-II (External) &Part-IV (Substation) as amendedup to date complete, as required. Panel size not less than 1200mm(H)x1400mm(W)x450mm(D) INCOMING a) 250 A, 36KAbreaking capacity( Ics) 4 pole MCCB with Microprocessor release- 1 No. BusBarChamber: 4 Strip aluminium bus bars of 300 Amps capacity b) Multi-function meter of 3phase 4wire, 5A Class1 FM with RS485-1No. c)3Nos.LED Phase Indication Lamp d) 6 Amps control MCB- 3No's. e) 250/5AC.Tcoil OUTGOING a) 160A,4P,25KA MCCB,TMR with spreders and rotary handles- 2No's. b)125A,4P,25KA MCCB,TMR with spreders and rotary handles -2No's. c)63A,4P,10KA MCB -3No's. (Note: The scope of work includes installation of above panel on suitable brick/CC pedetals or suitable angle frame work complete as required.)

Supplying, installation, testing and commissioning of floor mounted Outdoor type cubicle panel of following size made out of 2mm thick CRCA sheet for frame work and covers, compartmentalised, dust and vermin proof, hinged doors withknobs 3mm thick gland plate i/c cleaning and finishingwith 7 tank process for powder coating in approved shade, 250 amps capacity TPN aluminiumbus bars of high conductivity and all connection to individual circuits from the busbar ,DMC/ SMC bus bar supports and necessary cable supports for clamping the cable in the cable alley, bottom base channel of size 75mmx40mmx5mm, G.I earthbar of size 25mmx5mm at the rear for the entire width of the panel with 2Nos. earthstuds, connections from busbar to switchgear and control wiring withrequired size FRLS PVC insulated copper conductor cable of suitable size, separate gland plate for each cable entry gland plates including providing and fixing the following switchgear, as per attached specifications and confirming to the CPWD general specifications Part-I (Internal),Part-II (External) &Part-IV (Substation) as amendedup to date complete, as required. Panel size not less than 750mm(H)x1000mm(W)x450mm(D) INCOMING a) 200 A, 36KAbreaking capacity( Ics) 4 pole MCCB with Microprocessor release- 1 No. BusBarChamber: 4 Strip aluminium bus bars of 300 Amps capacity b) Multi-function meter of 3phase 4wire, 5A Class1 FM with RS485-1No. c)3Nos.LED Phase Indication Lamp d) 6 Amps control MCB- 3No's. e) 200/5AC.Tcoil OUTGOING a) 160A,4P,25KA MCCB,TMR with spreders and rotary handles- 2No. c)15 HP Starter -1 No d)7.5 HP Starter -3Nos e)63A,4P,10KA MCB -3No's. (Note: The scope of work includes installation of above panel on suitable brick/CC pedetals or suitable angle frame work complete as required.)

Supplying, installation, testing and commissioning of floor mounted Outdoor type cubicle panel of following size made out of 2mm thick CRCA sheet for frame work and covers, compartmentalised, dust and vermin proof, hinged doors withknobs 3mm thick gland plate i/c cleaning and finishingwith 7 tank process for powder coating in approved shade, 250 amps capacity TPN aluminiumbus bars of high conductivity and all connection to individual circuits from the busbar ,DMC/ SMC bus bar supports and necessary cable supports for clamping the cable in the cable alley, bottom base channel of size 75mmx40mmx5mm, G.I earthbar of size 25mmx5mm at the rear for the entire width of the panel with 2Nos. earthstuds, connections from busbar to switchgear and control wiring withrequired size FRLS PVC insulated copper conductor cable of suitable size, separate gland plate for each cable entry gland plates including providing and fixing the following switchgear, as per attached specifications and confirming to the CPWD general specifications Part-I (Internal),Part-II (External) &Part-IV (Substation) as amendedup to date complete, as required. Panel size not less than 750mm(H)x1000mm(W)x450mm(D) INCOMING a) 200 A, 36KAbreaking capacity( Ics) 4 pole MCCB with Microprocessor release- 1 No. BusBarChamber: 4 Strip aluminium bus bars of 250 Amps capacity b) Multi-function meter of 3phase 4wire, 5A Class1 FM with RS485-1No. c)3Nos.LED Phase Indication Lamp d) 6 Amps control MCB- 3No's. e) 200/5AC.Tcoil OUTGOING a) 125A,4P,25KA MCCB,TMR with spreders and rotary handles- 2No. b)63A,4P,10KA MCB -6No's. c).Time switch for 24 hour operation -1 No. (Note: The scope of work includes installation of above panel on suitable brick/CC pedetals or suitable angle frame work complete as required.)

Design,Supply, Installation, Testing and Commissioning of of 4 x 60 W LED Flood light fitting having colour temperature not less than 4000K, system lumen output not less than 19000 lumens and system wattage 240 Watts, built in electronic driver with surge protection not less than 5 KV etc. on existing pole as required . Make: K-lite or equvalent- Lux level should be as per Volley ball standards. Bidder has to design accordingly.

Design,Supply, Erection, Testing and Commissioning of 9 Mtr. Height Double side focus LED Flood Lighting pole with 1100 mm long overhang arm inclusive of electrical junction box, base plate, foundation bolts and nuts etc., on existing cement concrete pedestal etc as required. Make: Klite Street King or equivalent.

Design,Supply, Erection, Testing and Commissioning of 9 Mtr. Height single side focus LED Flood Lighting pole with 1100 mm long overhang arm inclusive of electrical junction box, base plate, foundation bolts and nuts etc., on existing cement concrete pedestal etc as required. Make : Klite Street King or equivalent.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

All kinds of Soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of Soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement

All works upto plinth level: Concrete of M25 grade with minimum cement content of 330 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete

steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade

Two or more coats on new work

Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50m and for all lift.

Providing & fixing of Puff panel container of size 6100mm (L) x 3050mm (B) x 2600mm (H) including all necessary Doors, windows, flooring, wall and ceiling panelling, and electrical fixtures and fittings as per the detailled specification in the tender document

Providing and fixing stainless steel sheet of AISI 304 grade, 2 mm thick, Matt finish, including laser cutting to appriopriate size, CNC bending, edge finishing, drilling, fixing with stainless steel screws/bolts and washers, on the floor including all labour, materials, tools & tackles, complete as per directions of Engineer-in-Charge.

320mm x 320mm

460mm x 460mm

480mm x 480mm

510 mm x 510mm

Providing and placing Mid Back chairs with overall height 1010-1120mm x overall width 640mm, featuring ergonomically comfortable chair. The back rest 730mm H x 490mm W, frame made up of industrial-grade polypropylene glass-filled material upholstered with Korean mesh. Seat size 525mm W x 505mm D and seating height 410-520mm, made of medium density foam, moulded and fixed with PP shell and upholstered with fabric. Seat sliding mechanism. provided with 3D adjustable armrest with PU pad with total height of 290-360mm . Auto weight sensing mechanism that can detect changes in weight distribution and adjust accordingly to optimize performance. Class IV Samhongsa gas lift with height adjustment of 110±2mm. The back shall be designed with contoured padded adjustable lumber support (Single/Double lumber support) for extra comfort. The mechanism of chair shall have following features: 360˚ revolving type, Back tilt with 4 position locking with anti-shock feature should be operated while taking back support for better adjustment for comfort, with tension adjustment knob. Base is made up of high pressure die casted in polished aluminium (optional: premium chrome/nylon) of 680mm dia and provided with 5 number heavy-duty twin-wheel nylon castors of 60mm dia each. Complete as directed by the Engineer in charge. Product should be AIOTA and IAQ Gold certified for inhouse air quality. The manufacturer should have ISO9001, ISO14001, ISO45001, ISO50001 from NABCB accredited agency and a member of BIFMA.

Providing and placing Desk Based Workstations with following specifications:Understructure, Screen and Cable management : Desk based system worktop supported on under structure made of MS legs Loop Leg of section 40x40mm, where Structure made from cold rolledsteel,thickness 1.2 mm. Epoxy powder coated spray paint, baked at temperature 200 C° coated of 70-80 micron thickness. Powder coating should be scratch resistance (cross hatch test 6x6 grid method). Screen :32mmthick Fabric Pinup screen with 2 mm thick MS Frame , For Back to back workstation we have taken screen height 360mm above the top & for Non sharing/ single side we have taken screen plus modesty panel below the top. Side/ Return Screen: 18mmthick fabric frame less screen with u clamp bracket. Wire management: Completely consealed wire management with vertical wire uptake from floor via MS Shared Electrical tower leg having removable cover one side and wire seperator for data and wire seperation, segregates to hozizontal cable tray below aluminium flipper with soft closure Epoxy powder coated spray color, baked at temperature 200 C°.Raceways contain the horizontal cable channel that fitted with a modesty panel tidily and effectively. Epoxy powder coated spray paint,baked at temperature 200 C° coated of 80-90 micron thickness. Powder coating should be scratch resistance (cross hatch test 6x6 grid method) Worktop :Worktop Made of 25mm thick E-1 grade particle board finished with 2mm PVC edge banding. E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm thick PVC edge banding tape of approved colour.The height of Worktop shall be 740mm from ground level. The particle board should be E-1 Grade with pvc edge banding. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron with recessed handles. Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

L Shape Workstation of size:- Size : 1500mm (W1) x 1500mm (W2) x 600mm (D1) x 600mm (D2) x 740mm(Worktop Height) x 1180-1220mm(Height of panel from Ground) for each person.

Providing and placing Desk Based Workstations with following specifications: Understructure, Screen and Cable management : Desk based system worktop supported on under structure made of MS legs Loop Leg of section 40x40mm, where Structure made from cold rolled steel,thickness 1.2 mm. Epoxy powder coated spray paint, baked at temperature 200 C° coated of 70-80 micron thickness. Powder coating should be scratch resistance (cross hatch test 6x6 grid method). Screen :32mmthick Fabric Pinup screen with 2 mm thick MS Frame , For Back to back workstation we have taken screen height 360mm above the top & for Non sharing/ single side we have taken screen plus modesty panel below the top. Side/ Return Screen: 18mmthick fabric frame less screen with u clamp bracket. Wire management: Completely consealed wire management with vertical wire uptake from floor via MS Shared Electrical tower leg having removable cover one side and wire seperator for data and wire seperation, segregates to hozizontal cable tray below aluminium flipper with soft closure Epoxy powder coated spray color, baked at temperature 200 C°.Raceways contain the horizontal cable channel that fitted with a modesty panel tidily and effectively. Epoxy powder coated spray paint,baked at temperature 200 C° coated of 80-90 micron thickness. Powder coating should be scratch resistance (cross hatch test 6x6 grid method) Worktop :Worktop Made of 25mm thick E-1 grade particle board finished with 2mm PVC edge banding. E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm thick PVC edge banding tape of approved colour. The height of Worktop shall be 740mm from ground level. The particle board should be E-1 Grade with pvc edge banding. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron with recessed handle. Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Rectangular Workstation of size:- 1200mm (W) x 600mm (D) x 740mm(Worktop Height) x 1100 mm

Rectangular Workstation of size:- 1500mm (W) x 600mm (D) x 740mm(Worktop Height) x 1100 mm

Providing & Fixing Meeting Table with following details and specifications : Table Size 4500mm x 1200mm x 740mm.Top is made of 36 mm thick Prelaminated particle board (E-1 Grade), finish with matching 2 mm PVC edge-banding. Grains of the table top to be unidirectional. The Modesty panel is made of Prelam Particle board Grade E-1 (Environmental Friendly) of thickness 18 mm pre -lamianted particle board with Edge-Banding(PVC) 2 mm. Understucture : Box Type Leg which is made out of 18mmthick thick Prelaminated particle board (E-1 Grade), finish with matching 2 mm PVC edge-banding. Shared box type legs having the vertical wire riser provusion inside of box. Wire management: Completely concealed wiremanagement with Aluminium anodized flipper with soft closure, wiring tray & beams Made from MS sheet 2 mm., flange structure epoxy powder 70-80 micron coated spray color, baked at temperature 200c with vertical wire uptake from floor via middle leg having removable cover. Wire seperator for data provided in cable tray below fipperand and with power pole for vertical movement of wires through junction box. E1 Grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1892).Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Providing and fixing ESD-safe industrial stool with non-upholstered moulded PU foam seat and backrest, ergonomically designed with anti-static and antibacterial properties, easy-to-clean black finish, seat size approximately 410 mm × 420 mm and backrest with lumbar support of size approximately 370 mm × 260 mm, pneumatically height adjustable from 500 mm to 700 mm using SGS-certified alloy gas lift with 360-degree swivel, mounted on corrosion-resistant five-legged aluminium base of minimum 640 mm diameter with five heavy-duty castor wheels, having a minimum load carrying capacity of 200 kg, complete in all respects as per specifications.

Supply, Installation, Testing & Commissioning of IP IR Fixed Lens Dome Camera @ 40/50fps,1 /2.8” 5 Megapixel progressive CMOS, progressive, 2.8/3.6 mm lens, scaning,0.005 Lux @F1.6, 0 Lux (IR ON),S/N Ratio with min, 55dB, quad stream; shutter speed: 1 / 3 ~ 1 /100000s,with minimum 10 user access, WDR-130 dB; WDR, HLC, BLC, 2D/3D DNR; IR distance 40m with defog option,SD card provision up to 2TB; Operating Temp: -30 to 60deg; Compression: H.265 / H.264 / Smart Codec / MJPEG; Analytics: Motion Detection, SMD, Intrusion, Tampering, Scene Change, Loitering, Line Crossing , Unattended Object Detection, Missing Object Detection, People Counter, Heat Map, Face Detection, Protocals:HTTP; HTTPs; TCP; ARP; RTSP; RTP; RTCP; UDP; SMTP; DHCP; DNS;IPv4/v6; QoS; UPnP; NTP;IEEE 802.1x; ICMP; IGMP; HTTPS, IP Filter,Digest authentication, User access log, TLS1.2 only, AES128 /256, SSH / Telnet closed, PCIDSS compliance; ONVIF S, G, T, M; IP66, IP67, IK10, UL, CE, FCC, BIS ER, MAKE IN INDIA with minimum Class 2 MII content, NDAA Compliant. Honeywell -HC50W45R3/Axis/ PELCO/ Bosch

Supply, Installation, Testing and commissioning of Windows OS based networking recorder of Intel Xeon silver 4210, 2.2 Ghz processor or higher, 32GB Memory, 1+1 750W hot plug redundant power supply, 2x240 GB M.2 SSD, RAID1 OS drive, 12 BAY expandable up to 240TB, RAID 0,1,5,6,10,50,60. UL & CE certified. Software: MJPEG,MPEG-4, H.264, H.265 compression, Bi directional audio support, Client Connection: Min. 18 remote clients per server from 9 remote work stations, 1 local NVR server; Salvo Layout- Desktop Client - Full, 2x2, 1x5, 3x3, 2x8, 1x12, 4x4. Web Client - 2x2.1x1,1x2,1x3. Mobile app (Phone) - 2x2,2x4,1x2, 1x1., Mobile app (Tablet) - 3x3, 2x2, 1x1; Pre & Post recording; per camera event reports; per user, configurator, session and viewer operator reportings; Digital signature, verification tool video clip authentication; WMV with digital certificate for authentication playable with Windows media player. ASF for faster exporting of longer than an hour backup clips; schedule recording continous and event based wiht H/M/D and holiday with exception days; continous and event based user activation recording per camera with camera wise compression format, resolution and frame rate; per camera picture controls: Sharpness, blur, brightness, contrast, hue, saturation, maintain aspect ratio, stretched, original size and picture mirror. To consider HDD @ 2MP, 15FPS, H.265 compression for 30 days. Consider Licenses as per existing setup MAXPRO and other components required for complete solution. Honeywell/Axis/PELCO/BOSCH

Supply, Installation, Testing and commissioning of Network Video Management & Monitoring Software (NVMMS) system with distributed architecture to collect, manage and present video from all the cameras and supports emerging technologies in the industry, like 4K resolution, H.265 video compression codec, multi-imager/lens cameras and 360° fisheye cameras. The NVMMS shall have option to support database redundancy and 1+1 and N+M NSM failover features for unforeseen/maintenance scenarios for increased system reliability. NVMMS shall support NSM's from a multiple location licenced for 250 cameras & Anaytics server should also have provision for concurrent Users., licenses should expandable upto 5000+ cameras & 10 user clients without any additional version upgrade. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, surrounding camera mode, Cybersecured with features such as Digital Signing, General Data Protection Regulation (GDPR) compliance, HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID & iOS phones, seamless integration with intgegrated security platform which provides HSDK&API for further integration with 3rd party systems. NVMMS shall support certified Analytics like intrusion/LoiteTrace/Face recognition/ANPR. And also should intergrate with Access control system. HARDWARE: OS IoT 2019; database server 2017 express; Intel Xeon E-2236, 3.4 GHz; 16GB DDR4 memory; 480GB SSDs dual RAID1 OS drive; G200 Video card, 2 USB and 1 VGA ports; Dual 350W hot plug platinum redundant power supply. UL & CE certified. Honeywell/Bosch/Axis/Pelco

Please Enable Macros to View BoQ information