Project for Interior Decoration and Elevation work of Auditorium Building in Narendra Nagar of Distt Tehri Garhwal (Second Phase)

Amount

CIVIL & ELEVATION WORK

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil

"Disposal of moorum/ building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-Charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floorWith Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified mininum cement content,the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum All works upto plinth level

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified mininum cement content,the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works above plinth level upto floor V level Concrete of M 30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified mininum cement content,the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars

Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing fly proof galvanised M.S wire gauze to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including utting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 1000x1000 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Sal wood

Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately)Second class teak wood 35 mm thick shutters

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws 35 mm thick shutters With ISI marked stainless steel butt hinges of required size Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R2 series with frame (40 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 metre).

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +1mm), with wall thickness 2.0 mm (+ 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (+ 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin- charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6 mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6 mm thick, spacer tube 12 mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm Airgap + 6 mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete ::300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm per coat

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Coupler 110 mm

Single tee with door 110x110x110 mm

Bend 87.5 degree 110 mm bend

Shoe (Plain) 110 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including 110 mm

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete .8 mm thick Granite of any colour and shade

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge.The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in Single Row Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding ofgranular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. 1000 mm dia

Supplying, installing and fixing of 6mm thick Exterior grade F-quality panels of standard size with both decor. FunderMax exterior panels are durometer high pressure laminates (HPL) as per EN 438-6 type EDF manufactured with norm confirmity of EN- 438-7 using patented NT technology (NT is non fading high performance acrylic polyurethane surface technology). Panels will be double hardened including acrylic polyurethane resin and thermally cued under high pressure. These panels will have CE-mark necessary for their use in buildidng applications. Installation of Fundr Max panels will be done by MBE rivets (with fixed and sliding points) with recommended Aluminum T-section of 100x50x2mm thick and L-section 50x50x2mm thick held by Aluminum wall bracket with wind load and dead load slot as per design, anvhored by standard anchor fasteners along with Thermal Separator. Installation of Fundermax panels will be done using Rear Ventilated Principlesonly, which is ensured by providing ventilation gap minimum 200 sqcm/per meter (for free flow of air behind the facade) for the facade and using the frame work with no horizontal section.

Providing and Fixing of Decorative Red Sand Stone Pillar for Elevation work of Auditorium Building in Narendra Nagar, Tehri Garhwal, made as per design Complete. Each Decorative Elevation Stone Pillar having Bottom and Top diametre 450 mm and Total height of Pillar 8500 mm ( with top and Bottom Square Design Pedestal) above the 6500 mm of Pillar for Arch arrangement Each Stone Pillar suitably spray Polished and required Lubricant and bounding material with superior quality Overall weight of the Decorative Red Sand Stone Pillar is not less than 8500 mm, inculding Making of Pillar,Carriage/Transportation,Loading,Unloading and fixing in position with nessessary arrangement such as scafollding,Lifting Machineat site including cost of all materials, T&P etc.

Providing and Fixing of Decorative Red Sand Stone Pillar for Elevation work of Auditorium Building in Narendra Nagar, Tehri Garhwal, made as per design Complete. Each Decorative Elevation Stone Pillar having Bottom and Top diametre 300 mm and Total height of Pillar 2600 mm ( with top and Bottom Square Design Pedestal) above the 2000 mm of Pillar for Arch arrangement Each Stone Pillar suitably spray Polished and required Lubricant and bounding material with superior quality Overall weight of the Decorative Red Sand Stone Pillar is not less than 3200 mm, inculding Making of Pillar,Carriage/Transportation,Loading,Unloading and fixing in position with nessessary arrangement such as scafollding,Lifting Machine (Sufficent weight Lifting machine/Hydra machine) at site including cost of all materials, T&P etc. complete as per direction of Engineer-in- charge.

Providing and Fixing of Decorative Red Sand Stone Arch/Mehrav for Elevation work of Auditorium Building in Narendra Nagar, Tehri Garhwal, made as per design Complete. Each Decorative Elevation Arch/Mehrab having Length 5400 mm and Both Edge Depth /height of Arch/Mehrab 2300 mm and middile depth is not less than 1000 mm ( with Complete decartive and design work in Front of Arch/ Mehrab) Each Red Sand Stone Arch/Mehrab suitably spray Polished and required Lubricant and bounding material with superior quality. inculding Making of Pillar,Carriage/Transportation,Loading,Unloading and fixing in position with nessessary arrangement such as scafollding,Lifting Machine at site including cost of all materials, T&P etc.

Providing and Fixing of Decorative Red Sand Stone Arch/Mehrav for Elevation work of Auditorium Building in Narendra Nagar, Tehri Garhwal, made as per design Complete. Each Decorative Elevation Arch/Mehrab having Length 2700 mm and Both Edge Depth /height of Arch/Mehrab 1300 mm and middile depth is not less than 700 mm ( with Complete decartive and design work in Front of Arch/ Mehrab) Each Red Sand Stone Arch/Mehrab suitably spray Polished and required Lubricant and bounding material with superior quality. inculding Making of Arch,Carriage/Transportation,Loading,Unloading and fixing in position with nessessary arrangement such as scafollding,Lifting Machine at site including cost of all materials, T&P etc.

Providing and Fixing of Decorative Red Sand Stone Cornice and their top slab for Elevation work of Auditorium Building in Narendra Nagar, Tehri Garhwal, made as per design Complete. Each Decorative Elevation Cornice having Length 600 mm and Edge Depth /height of Cornice 450 mm and End depth is not less than 250 mm ( with Complete decartive and design work in Front of Cornice) Each Red Sand Stone Cornice suitably spray Polished and required Lubricant and bounding material with superior quality. inculding Making of Cornice,Carriage/Transportation,Loading,Unloading and fixing in position with nessessary arrangement such as scafollding,Lifting Machine at site including cost of all materials, T&P etc.

Providing and Fixing of Decorative Red Sand Stone Front Plate for Elevation work of Auditorium Building in Narendra Nagar, Tehri Garhwal, made as per design Complete. Each Decorative Elevation Plate having Length 5400 mm and Depth /height of Plate 500 mm ( with Complete decartive and design work in Front of Plate) Each Red Sand Stone Plate suitably spray Polished and required Lubricant and bounding material with superior quality. inculding Making of Cornice,Carriage/Transportation,Loading,Unloading and fixing in position with nessessary arrangement such as scafollding,Lifting Machine at site including cost of all materials, T&P etc.

Providing and Fixing of Decorative Red Sand Stone Railing for Elevation work of Auditorium Building in Narendra Nagar, Tehri Garhwal, made as per design Complete. Each Decorative Elevation Railing having Length 1000 mm and Depth /height of Plate 1000 mm ( with Complete decartive and design work in Front of Railing) Each Red Sand StoneRailing suitably spray Polished and required Lubricant and bounding material with superior quality. inculding Making of Railing,Carriage/Transportation,Loading,Unloading and fixing in position with nessessary arrangement such as scafollding, at site including cost of all materials, T&P etc.

ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group B

Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Group B

Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch,connections etc. as required.

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Wiring for light) power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire following sizes of FRLS PVC insulated copper conductor, single with the core cable in surface/ recessed steel conduit as required

2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire

2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire

2X4 sq.mm+1X4 sq. mm earth wire

2 x 6 sq. mm + 1 x 6 sq. mm earth wire

2 x 10 sq. mm + 1 x 10 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

32mm dia

40mm dia

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required.

8 Way (4+24), Double door

12 way (4 + 36), Double door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

75 mm X 75 mm X 60 mm deep

150 mm X 75 mm X 60 mm deep

200 mm X 250 mm X 75 mm deep

Supply of following sizes of XLPE insulated PVC sheathed, Aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 amended upto date.

3.5 C x 240 Sqmm

3.5 C x 95 Sqmm

3.5 C x 50 Sqmm

3.5 C x 35 Sqmm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

31/4 X 35 sq. mm (32mm)

31/4 X 50 sq. mm (35mm)

31/4 X 95 sq. mm (45mm)

31/4 X 240 sq. mm (62mm)

31/4 X 300 sq. mm (70mm)

Supply of following sizes of XLPE insulated PVC sheated, Copper conductor armoured power Cable of 1.1 KV grade conforming to IS 7098 amended upto date.

4C x 16 Sqmm

4C x 10 Sqmm

2C x 10 Sqmm

2C x 6 Sqmm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2X 6 sq. mm (19mm)

2 X 10 sq. mm (19mm)

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

4X 25 sq. mm (28mm)

4 X 50 sq. mm (35mm)

3 X 300 sq. mm (70mm)

Laying and fixing of one number PVC insulated and PVC sheathed /XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS Metre flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS Metre flat clamp)

Supplying and making cable route marker with cement concrete Each 585 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10 cm including inscription duly enaraved as reauired.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

600 mm width X 50 mm depth X 2.0 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supply, Erection, Testing & Commissioning of cubical type Panel suitable for 433V, 3 Phase, 4 Wire 50Hz AC supply system. Fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates. Cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable Amp capacity extensible type TPN Aluminium alloy bus bars of high conductivity, DMC/ SMC bus bar supports, with short circuit withstand capacity of 25 KA for 1sec. as specified with panel details, bottom base channel of MS section not less than 75x40x5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common GI earth bar of size 50mm x 6mm at the Bottom with 2 Nos. earth connection. Solid connections with Al. links of required size from main bus bar to switchgears and control wiring with 2.5/1.5 sq.mm. FRLS PVC insulated copper conductor Single Core cable and cable alleys, cable gland plates etc providing in following Panels complete as required.Ref. IS:8623.MAIN LT PANELIncoming 1 nos. of 630 amp rating,25 KA electrically operated four pole ACB of horizontal drawout pattern for bus bar connection on outgoing side and cable connection on the incoming side. The breakers shall be provided with microprocessor based release/relay (equivalent to SR-18 G) having variable range of overcurrent, short circuit and earth fault protection with time lag facility for each of the fault for achieving discrimination. The breaker shall be electrically interlocked with other incomer/ DG Incomer / Bus Coupler as required.Indicating Panel for incomer The Indicating panel of the incomer ACB shall be provided with the following; (a)Multifunction Meter with RS-485 communication port with required set of CT's (b)3 Nos. phase indicating lamps backed upwith MCB.(c)2 Nos.ON/OFF indicating lamp on incomer feeder for indicating the status of feeder.TNC breaker control switch Protective devices for each incomerThe incoming ACB shall be provided with the following protective devices:-Under Voltage & Over Voltage relay with timer.Separate CT's shall be provided for protective system and measuring system. 3 no. of CT on R,Y,B, phase for Automatic power factor correction relay.Bus Bar 800 Amp. TPN aluminium bus bars for suitable length and of crossection not less than 1.2 sq. mm/ amp.Bus bars shall be insulated by heat shrinkable sleeves and clip on shrounds for joints. Bus Bar shall be designed to withstand a fault level of 35 KA at 415 Volts.Outgoing All outgoing feeders shall be provided with one sets of phase indicating lamps and trip indication lamp with protection MCB, and Digital Ammeter and CT's.3 Nos. 160 amp FP MCCB of 25 KA service breaking capacity and trip setting as required.2 Nos. 100 amp FP MCCB of 25 KA service breaking capacity and trip setting as required.4 Nos. 63 amp FP MCCB of 25 KA service breaking capacity and trip setting as required.4 Nos. 63 amp FP MCCB of 25 KA service breaking capacity and trip setting as required.1 Nos. 63 amp FP MCCB of 25 KA service breaking capacity and trip setting as required.Item as stated above

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way , Double door

12 way , Double door

Supplying and fixing of following rating, four pole , 415 volts, MCCB in the existing DB complete with connections, testing and commissioning etc. as required.

40 amps, 10KA

63 amps, 10KA

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole

Double pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating ,double pole (single phase and neutral ), 240 volts , residual circuit breaker (RCCB) ,having a sensitivity current 100 milliamperes in the existing MCB DB complete with connection testing and commissioning etc. as required

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and Fixing of 250 KVA 3 Phase Silent DG Set KIRLOSKAR GREEN Make with Engine Model 6SL90ETA 4G2, 415 VOLT, 200 KW, BHP-310, Liquid Cooled 250 KVA Alternator, KIRLOSKAR MAKE

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & sprina washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G | tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

The rates shall include all components that may be required to make the supply complete in all respects such as :All lighting control equipments.Internal wiring between accessories.Earthing Complete provision for installation. terminal.Supply of the following lighting fixtures with all fixing accessories etc. as required.

LED Downlighter 12W LED 4000 lm or approved equal in quality and design complete in all respect.

LED recessed 2'x2' lighting or approved equal in quality and design complete in all respect.

Cieilng / Surface mounted LED tubelight 30W

LED mirror light LED 1000lm

Bulk head lighting fixtures Philips make FXC-101 or approved equal in quality and design with 9 watt CFL lamps.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.510 mm sweep

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required .

Supplying and fixing extra conduit down rod of 20 cm length G.I.pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Telephone socket outlet

TV antenna socket outlet

Supply and installation of wall/recessed mounting KRONE connector type telephone tag block of following sizes in sheet metal enclosure of suitable dimensions fabricated out of 16 SWG sheet steel with castle key lock, hinged gasketed type cover including termination of telephone cables, making connections, painting of box etc, complete as required.16 Pair Tel Tag Block

Supply and laying of 4 Pair UTP Cable 23 AWG copper with integral cross-member pair separator (bidirectional tape, strips and others will not be accepted) for uniform characteristic impedence should meet or exceed the TIA/EIA 568-B. 2-1 (Cat-6) standards for physical and electrical specifications. (Tested to 600 MHz.Cat-6E Cable

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25mm

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of 6 inches dia, 2 watts, 70/100 volts ceiling speaker complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent aspiration detector for area coverage of minimum 5000 sq. ft complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supply and drawing of 2 C X 1.5 Sq mm Fire Survival Cable for Detectors, Devices, Speakers and Notification Appliances installed on ceiling surface as per IEC 60331-11 & IEC 60331-21.

Providing and Fixing SUKRANTI/ 8 Passenger Lift/ 544Kgs / 1.25 Speed / 4 Floors / 4 Stops / Stainless Steel Car Cabin

PLUMBING WORK

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing toilet paper holder :C.P Brass

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug, PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately)(Under Counter Basin)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per 1$:13983 with C.l. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 225 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms

Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190gms.

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2” BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing PTMT urinal cock of approved quality and colour.15 mm nominal bore, 80 mm long, 42 mm high and 30 mm wide with BSP female threads weighing not less than 48 gms

Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal.

Providing and fixing flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.g white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified.Medium.

Providing, fitting and fixing Chrome Plated robe hook complete as directed and specified.Medium.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge..

Providing, fixing, testing and commissioning pressurized electric water heater with copper sheet container with suitable length of electrical cable and 15 amp 3 pin plug top, complete in all respect 15 Litre.

Providing, fixing, testing and commissioning pressurized electric water heater with copper sheet container with suitable length of electrical cable and 15 amp 3 pin plug top, complete in all respect 25 Litre.

Supplying, Installation, Testing and Commissioning of uPVC, P or S trap of self cleansing design with / without vent. arm Setting in cement concrete 1:2:4 mix complete including cost of cutting & making good the Wall / Floors wherever required. 110 mm inlet & 110 mm outlet

Providing & fixing PVC inlet fitting with one or more inlets fabricated from 110 mm outer dia UPVC pipe and solvent welded sockets and fixed to UPVC Floor Trap and set in cement concrete as per drawing complete

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion

Coupler

Single tee with door

75 mm bend

110 mm bend

Shoe (Plain)

75 mm bend

110 mm bend

Providing and fixing M.S holder-bat clamps of approved design to PVC/Sand Cast iron/ cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.

100 mm dia

75 mm dia

Providing and fixing soil, waste and vent pipes :Sand cast iron S&S pipe as per IS: 1729

100 mm dia

75 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall

Internal work - Exposed on wall

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermalstability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. External work

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

50 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

25 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

25mm nominal bore (Horizontal)

50 mm nominal bore (Horizontal)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :50 to 80 mm nominal bore

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Supply and installation of Kirloskar make (1.5 HP) Single phase

FIRE FIGHTING WORK

(A) Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (C) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 Ipm at 70 m Head

(A) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (A) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming tolS: 1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 HzAC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (D) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 70 m Head

(A) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) (B) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (C) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. (D) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 602280 Ipm at 70 m Head

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads.900 Ipm at 35 m Head

Sprinkler flexible drops stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread 1 No. reducer + 1 No. Nipple + 2 Side Brackets + 1 Center Bracket +625mm stockbar1500mm flexible drop

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required

Single headed Gunmetal

Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required

Gun Metal

Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:

Gun Metal

Stainless Steel (Grade 304)

SITC weather proof M.S cabinet size 1200 mm x 2100 mm x 800mm,Supplying, installation, testing and commissioning of weather proof M.S cabinet size 1200 mm x 2100 mm x 800mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following:

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.150mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

50mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

BALL VALVE Supply,installation, approved make Ball valve 25 mm MAKE:KARTAR,ZOLOTO 25 mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required:4 way - 150 mm dia M.S. Pipe

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/em2 complete as required.

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0-16 Kg / cm2 .

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer,nipple, 2 side brackets, center bracket, stockbar of following sizes complete as reauired.

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required

80mm dia

100mm dia

150mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304,sheet with 3 mm dia holes with stainless steel flange.

100 mm dia

150 mm dia

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required

Providing and fixing fire extinguisher of 4.5 kg carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006 Make-Lifemex ,Omex 4.5 KG

Supply, installation, testing and commissioning of ISI marked (IS:15683) portable chemical fire extinguisher, water (gas pressure) type capacity 9 litres with squeeze valve and nozzle and complete in all respects including initial fill and wall suspension brackets as required as per specifications.9 ltr4.5 KG

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/em2 complete as required.1321.00

Swinging type hose reel complete with 19mm x 40 Mtrs.Thermolplastic hose Type-ll

Hose reel drum

25mm dia gun metal globe valve & nozzle.

Smoke Detector with built in LED, mounting base complete with all connection etc.

Supplying, installation, testing & commissioning of heat detector Each 1071.00 operating at 54°C/57°C with rate of rise cum fixed tempreature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector Each 1153.00 with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call Each 474.00 boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder Each 557.00 with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as reauired.6 Zone

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset,acknowledge and silence switches complete as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.speaker cable Single pair, 2-core, 1.5 sqmm

HVAC WORK

Supplying, Installation, Testing & commissioning of 4th Generation Full Inverter VRF System with Modular type outdoor units (Top Discharge), all scroll DC Inverter compressors for Cooling & Heating applications along with different types of indoors compatible with VRF ODUs. All inverter capacity controlling compressors shall be suitable for 3 Phase, 50 Hz. All proposed outdoor unit should have minimum COP of 3.6 at 100% load condition for Cooling in standard AHRI test conditions.The unit should be suitable for ambient condtion of 5°C to 43°C during summers. The unit shall be suitable upto 225 metre piping between outdoor and farthest indoor unit with height difference of 50 metre between outdoor and indoor. The capacity of unit are follows.

28 HP with AHU Kit For TFA-2650 CFM

18 HP With AHU Kit for AHU-5000 CFM

08 HP for room at back stage

10 HP for waiting area & projector room

Supplying, Installation, Testing & commissioning of hi statcic ductable Type/Casseette Type Indoor units equipped with pre-filter, fan section with suitable static fan, multispeed motor, coil section with DX coil, outer cabinet, drain pan, insulation, pipe connections etc. of various capacities as per specifications and drawings. VRV INDOOR UNITS

Cassette Type indoor Units

1.5 TR - For back stage lobby

1.5 TR - For Waiting lobby projector room

2.0TR - For Waiting lobby Balcony sitting

Hi Wall Type Inoor Units

1.5 TR - For rooms back stage

1.5 TR - For projector room

FLOOR MOUNTED AIR HANDLING UNITS WITH DX COIL Double Skin type Floor mounted units for DX coil application complete with double skin (45±2 mm) insulated with CFC / HFC free polyurethane foam (PUF) panels of 48 Kg/cum density. Sandwitched between 0.6 mm thick G.I. Sheets. Outer skin shall be pre coated G.I. sheet and internal skin shall be plain G.I. Sheet. The blower shall be of forward / Backward curved type. minimum 4 Row cooling coil, Maximum Face velocity across filter 500 FPM, The thickness & dia of copper tube should be as per DAIKIN Standard, prefilter section with synthatic media filters, drive package, vibration isolating rubber bush to fans and motor to avoid transmission of vibration.22Ga SS-304 drain pan dylu puf injected & covered with Plain GI sheet.

5000 CFM / 30mm ES / 4RD/14TR/3.7KW/IE-3 15425 Level

Double Skin type floor mounted units for DX coil application complete with double skin (45±2 mm) insulated with CFC free polyurethane foam (PUF) panels of 48 Kg/cum density. Sandwitched between 0.6 mm thick G.I. Sheets. Outer skin shall be pre coated G.I. sheet and internal skin shall be plain G.I. Sheet. The blower shall be of forward / Backward curved type. minimum 8 Row cooling coil, Maximum Face velocity across filter 500 FPM, The thickness & dia of copper tube should be as per DAIKIN Standard, prefilter section with synthatic media filters, drive package, vibration isolating rubber bush to fans and motor to avoid transmission of vibration.22Ga SS-304 drain pan duly puf injected & covered with Plain GI sheet. Plenum required to connect fresh air duct, AL S/A & F/A duct damper required with Unit.

2650 CFM / 40mm ES / 8RD/22TR/7.5KW/IE-3

Supplying, Installation, Testing & commissioning of Corded remote.

For Hi Wall split - Cordless

For Cassette Type Units - - Cordless

For AHU Unit

For TFA Unit

Supply, Installation, Testing & Commissioning of PC based central controller (Centralised Controller-I Touch) that can be integrated to web system that allows user to acces to the control system online anytime without access to PC also.It should be capable of controlling 256 indoors. The featrues can be controlled like Temperature/Fan speed/self dignosis/Scheduling (Daily/weekly/yearly).

Supply, Installation, Testing & commissioining of Refnet joints for proper distribution of refrigernt through the complete circuit for indoor and Outdoor etc. as required.

Indoor Y-Joint

Outdoor Joint

Supply, Installation, Testing & commissioining of interconnecting refrigerant piping along with closed cell elastomeric insulation and C chenel supports, between indoor & outdoor units duly insulated as per specifications.

41.3 mm O.D. ( insulation : 19 mm )

34.9 mm O.D. ( insulation : 19 mm )

28.6 mm O.D. ( insulation : 19 mm )

25.4 mm O.D. ( insulation : 19 mm )

22.2 mm O.D. ( insulation : 19 mm )

19.1 mm O.D. ( insulation : 13 mm )

15.9 mm O.D. ( insulation : 13 mm )

12.7 mm O.D. ( insulation : 13 mm )

9.5 mm O.D. ( insulation : 13 mm )

6.4 mm O.D. ( insulation : 13 mm )

Supply, Installation, Testing & Commissioning of PVC heavy class drain piping insulated out of 09 mm thick Class 'O' closed cell elastomeric nitrile rubber material of approved make as per specification complete with supports, consumables, fittings, pipe sleeves, U trap of following sizes.

Providing and fixing of shielded Control cable in PVC Conduit from outdoor to indoor / From AHU Kit to outdoor & indoor / For Remote control (Communication Cable)

2 Core x 1.5 sq.mm in 20mm Conduit

Supply, Installation, Testing and Commissioning of Supply air Tube Axial/Vane Axial flow (Rectangular Connectivity) fan suitable for outdoor/indoor application of following capacity with heavy Gauze GI/ MS casing and aluminium alloy impellers with high efficiency, blades, the impeller directly driven by TEFC induction motor (motor should be of high efficiency (IE-3) with minimum efficiency of 75% for larger fans up to and greater than 450mm Dia and 65% for smaller fans) suitable to operate at 415 V ± 10 %, 50 Hz,3 Phase,1450/950 RPM of class 'H' insulation etc. complete as required and as per specifications. Fan shall be with high quality fire proof flexible connection at inlet and outlet. Cost of spring isolators for the fans needs to be included. Fans which have to be operate In case of fire shall be activated receiving signal from fire alarm system. Fan capacity shall be as follows. Sound pressure level of fans shall not exceed [email protected] Mtr distance (this sound level is without duct silencer). In case of fire , the noise level of fans should not exceed 80dbA @ 3.0 Mtr distance. Fan should be AMCA certified for Air & Sound performance both. All fan sound levels to be mentioned are to be measured at hemispherical reverberant room conditions and Fan supplier to provide the design calculations for estimating the noise level at actual site conditions. Fan Velocity: ≤ 12.5 m/s

12500 CFM / 25mm Static / as per tech / IE-3 Motor/H Class for exhaust air in case of fire

12500 CFM / 25mm Static / as per tech / IE-3 Motor/H Class for Fresh air in case of fire

Supply, installation, balancing and commissioning of factory / site fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, supports etc. as per approved drawings and specifications of following sheet thickness complete as required

All duct to be support from purlin,

Duct Size 0-750mm - 24 Ga

Duct Size 751-1500mm - 22 Ga

Duct Size 1501-2250mm - 20 Ga

Duct Size 2251mm and above - 18 ga

GI Round Duct

600mm Dia - 24Ga

450mm Dia - 24Ga

400mm Dia - 24Ga

Supply & fixing of double canvas fire rated connection between Indoor unit & Duct Canvas Connection

Supply & fixing of powder coated extruded aluminium Grill / Diffusers

Al Grills with Al Damper

Al Grills without Al Damper

Al Diffusers with AL Damper

Al Diffusers without AL Damper

Al Jet Nozel with Butterfly Damper - 200 Dia

Al Jet Nozel with Butterfly Damper - 300 Dia

Supply & fixing of GI Duct Damper 20Ga/22Ga GI Duct Damper

Supply & fixing of Motorised Fire Damper Supplying, Fixing,testing and commissioning UL listed of Fire damper in supply air duct /main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.

Fire Dampers.

Actuator, Control Panel & Wiring including etc as required

Supply & fixing of non motorised Fire Damper (Fusible Link Type)Fire Dampers.

Supply & fixing of powder coated extruded aluminium Louvers with bird screen for Fresh Air Fresh Air louvers

Supply and Application of external thermal insulation of supply /return air ducting using closed cell elastomeric nitrile rubber insulation with class 'O' fire retardant properties as per the specifications and drawings.

19mm thcik on S/A Duct

13mm Thick on R/A Duct

Supply and Application of internal acoustic lining of supply air ducting using open cell nitrile rubber insulation with density within 140-180 Kg/m3 as per the approved shop drawings and specifications. Insulation material shall be bonded with the ducts using metal screw and washers to facilitate grip to the GI sheet.10mm thcik

Providng and fixing of Refrigerant Top Up inculding all

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

ACOUSTICAL WORK

Auditorium Hall & Control Room Ceiling: Providing and Fixing Acoustics Cement Fibre Elegant tile 595x595x5mm with square edge density 1050kg/m3 covered with absorbtive microfiber coating on the front side and Acoustics fibre on the back side, thus making it acoustically absorbtive, water resistance, fire resistant Absorption Cofficient upto 0.89 at 160 Hz tested as per ISO 354 ans Anti Bacterial test as per JIS-Z2801-2010. The tiles are anti sag and are to be installed on T24 grid system of 0.6mm thick ,Main ‘T’ length minimum 3000mm, web minimum 35mm to be placed at 600mm centre to centre and secondary cross ‘T’ of length 600mm, web minimum 35 mm, inter locked, Wire Support for Main T to be taken at every 1200mm length wise and 600mm width wise,Specially designed for Acoustic Vibration management and long life with a backing of Chord 50mm 1000 GSM thick absorbwool tested as per Fire Retardant ASTMD 635-1991 and IS 15061-2002 for excellent results.

Stage Ceiling: Providing and Fixing of Melody String Panel having sizes 595x595/595x1195mm and thickness of 15 mm are made with inorganic binder wood fibre, which in all contribute to its wondering features & provide NRC 0.85 tested as per IS:8225-1987 (Equivalent to ISO: 354-1985 & ASTM 423-90).Panels should be of ecological green material. It should be non flammable as per IS:3614 (Part-II). It should facilitate fast, rapid construction of walls & roofs. To be installed on T24 grid system of 0.6mm thick ,Main ‘T’ length minimum 3000mm, web minimum 35mm to be placed at 600mm centre to centre and secondary cross ‘T’ of length 600mm, web minimum 35 mm, inter locked, Wire Support for Main T to be taken at every 1200mm length wise and 600mm width wise,Specially designed for Acoustic Vibration management and long life with a backing of 50mm 1000 GSM thick absorbwool tested as per Fire Retardant ASTMD 635-1991 and IS 15061-2002 for excellent results.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T,bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G | sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending .

Hall Wall Paneling (from 2.40 mtr. Height to Ceiling) & Control Room Walls (from 1.20 Ft. Height to Ceiling): Providing and Fixing Melody Fabric Panel having sizes 600x600/600x1200 mm and thickness of 20/25 mm with inorganic binder wood fibre base panel and covered with Acoustically transparent non woven Fabric on the front side, with an option of colours as per choice & provide NRC 0.85 tested as per IS:8225-1987 (Equivalent to ISO: 354-1985 & ASTM 423-90). Panels should be an ecological green material. It is non flammable as per IS:3614 (Part-II). It facilitate fast, rapid construction of walls & roofs. It is economic & energy efficient. To be installed with PVC H Profile on G.I studs 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick Acoustic Wool tested as per Fire Reatrdant ASTMD 635-1991 and IS 15061-2002 for excellent results.

Hall Wall Treatment (from FFL to 2.40 mtr height) & Control Room Walls (from FFL to 1.20 mtr Height): Providing and Fixing of Wooden Slats 2430x131 mm with thickness of 16 mm MDF backed with acoustical Fleece providing sound absorption of NRC 0.70 tested as per IS:8225- 1987 (Equivalent to ISO: 354-1985 & ASTM 423-90).To be installed with 15mm Aluminium profile conforms to Aluminium Alloy 6063-T 6.Temper As per BS:1474-1987 and G.I Lock in clips on the back of tongue and Groove system. The density per panel is 750-800 kg/m3.The panels come with tongue & groove for seamless patterns,2-14mm Groove and visible panel.Wooden slats are made from acoustical fibreboard with linear perforations for excellent uniformity. The perpendicular holes are available on the back of panel which are covered by black acoustical fleece. To be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 25mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick,1000 GSM Acoustic Wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results.

Stage Walls: Providing and Fixing of Melody String’ Panel having sizes 600x600/600x1200 mm and thickness of 20 mm are made with inorganic binder wood fibre, & provide NRC 0.85 tested as per IS:8225-1987 (Equivalent to ISO: 354- 1985 & ASTM 423-90). Panels should be of ecological green material. It should be non flammable as per IS:3614 (Part-II). It facilitate fast, rapid construction of walls & roofs. Melody String should be installed with Coloured Aluminium H Profile on G.I studs 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick Acoustic Wool tested as per Fire Reatrdant ASTMD 635-1991 and IS 15061-2002 for excellent results.

Providing and Fixing of Insulation made of 50mm thick Underdeck Insulation 500 GSM with the backing of Aluminium foil. The Product should be eco friendly and it's having excellent sound absorption/thermal insulation properties. Can Sustain Temperature range of -40 CL to 160 CL for 2 Hours. Light weight, easy and safe for Installation.To be fixed under MS roof held with weld mesh wire and Hardware.

P/f of Main Curtain made out of fire retardant fabric of Reliance Industries or equivalent with horizontal sliding arrangement & Motorised operation complete with runners, master runners, pullies, 3 mm steel wire rope, 1 HP motor(Crompton) 2 nos. air breaker contactors (L&T/SIEMENS), 2NOS. micro switches for auto stop, 3 nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900 mm and should be stitched in double gathering with backing fabric. I/c frill as per requirement.

P/f Rear Curtain made out of black colour fire retardant fabric of Reliance Industries or equivalent with horizontal sliding arrangement & Motorised operation complete with runners, master runners, pullies, 3 mm steel wire rope, 1 HP motor(Crompton) 2 nos. air breaker contactors (L&T/SIEMENS), 2NOS. micro switches for auto stop, 3 nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900 mm and should be stitched in double gathering. I/c frill as per requirement.

Providing and fixing Frill bars, fixed type made out of 25mm dia GI pipe, supported from ceiling structure, As required, Frill to be made out of Black Glazed Cotton Cloth, stitched with pleats,Frills, etc., as required.

Providing and Fixing of suitable size Stage Wing panel made out from 25mm x 50mm of 16swg MS pipe duly painted in black colour with black glazed casement cloth both side having manual moving facility.

Providing & fixing of suitable size Cyclorama screen frame made out from 32mm 16swg tubluar pipe for inner/outer frame & 50mm dia black pipe for back support duly painted in black colour with Beta white PVC perforated screen to be fixed on frame with support of cotton rope wire. (Approx Size: 36 ft x 20 ft)

Providing and fixing of 95x20 mm second class Teak wood klin seasoned planks with tongue & groove joints. Teak wood planks to be of minimum length 450mm. The Teak wood planks to be fixed over a layer of 12 mm commercial ply of approved make fixed to Sal wood frame work of 50 x50 mm and 50x50 mm at 600 mm centre to centre (HxV). The Sal wood shall be kiln seasoned and chemically treated.The framework to be jointed with mathani cut method. The framework to be filled with 50 mm thick thermal bonded fiberglass of density 24kg/cum. The stage floor to be PU polished with use of orbital sanders to make floor even before polishing.

Supply and Fixing Procenium made out from 6-12 mm Ply wood Board and 25 mm Foam and mossi- wellvet clothe bothe side for the entire front of the stage left and centre with MS Frame

SITC of 150W High Quality LED Parcan Light complete with, Lamp source 3200K CCT Colour temperature CRI & TLCI Values above 95 COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 3 channel control Beam Angle of 9˚ / 25˚ / 45˚ Total Power Consumption of 165W High quality output replacing 1000W Halogen Par Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate, Linear Dimming 0 ~ 100% Fuse and Internal safety protections Strobe option Adjustable 1~25 times/Sec Variable Fixture provided with Yoke of Manual Adjustment 5 Pin XLR for DmX , Black powder coated body. Approved Make : Leksa/Canara/TDH

SITC of 300W LED Profile Spot 19 Degree Light complete with, 3200K CCT Colour Temperature COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) CRI & TLCI above 95, Strobe option Adjustable 1 ~ 25 times / Sec 4 Kinds of dimming curves, Black finish housing, Manual Focus with 4 Beam shaping cutters Efficient and well-designed Lamp reflector Efficient Copper tube based Heat Sink for Heat Dissipation Sleek and Unique Designed Light weight body Fixture provided with Yoke of Manual Adjustment DmX 512 dimming with 1 or 3 Channel modes. Approved Make : Leksa/Canara/TDH

SITC of 54 x 3W LED Warm White Light, Beam Angle 25° complete with RGBW 3W Lamp source x 54 Pcs DmX 512 dimming with 8 Channel High Bright Red, Green, Blue, White LED’s Source Unlimited Color Mixing through DmX 0 ~ 100% Linear dimming In built presets for different colors Strobe Mode 20 times/Sec Data DmX through 3 / 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out Connections High precision colors Powder coated Black finish housing IP20 protection Having Sound Control & Master Slave Auto Run Mode Illuminate the Indoor stage with unlimited colour effects Rigidly built pressure die-casted Aluminium body.

SITC of 400W LED Blinder Light 30 Degree complete with 3200K CCT 4x100W Chip On Board LED Lamp source COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 4 /8 Channel modes CRI & TLCI Value > 90 , Strobe option Adjustable 1 ~ 25 times / Sec Variable, Beam Angle 30 Degree Total Power Consumption of 420W 11.7KHz Refresh Rate, In built preset’s for effects Fuse and Internal safety protections, Active Cooling with Low Noise Fan, 5 Pin XLR for DmX, High quality well designed inbuilt reflector, Flicker Free 100% for Tv & Film Cameras, Black finish housing. Approved Make : Leksa/Canara/TDH

SITC of 54 x 3W LED Par Light RGBW, Beam Angle 25°complete with RGBW 3W Lamp source x 54 Pcs DmX 512 dimming with 8 Channel High Bright Red, Green, Blue, White LED’s Source Unlimited Color Mixing through DmX 0 ~ 100% Linear dimming , In built presets for different colors Strobe Mode 20 times/Sec Data DmX through 3 / 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out Connections High precision colors, IP20 protection Powder coated Black finish housing Having Sound Control & Master Slave Auto Run Mode Illuminate the Indoor stage with unlimited colour effects Rigidly built pressure die-casted Aluminium body. Approved Make : Leksa/Canara/TDH

SITC of DMX light control mini pearl : DMX Lighting Console can control up to 96 fixtures. It is compatible with the library in Avolite Pearl R20 format and featured with built-in shapes effects of pan/tilt circle, RGB rainbow, beam dimming wave, etc, Approved Make : Leksa/Canara/TDH

SITC of Power Distribution Electrical panel having a Incomer of 100A. Floor mount / rack mount / wall mount. Miniature circuit brakers of single poles shall be fixed of different ratings from 6/10/16/25A as per the lighting fixtures.Wiring inside the module for power, control protection and instrument etc. Provided with ivery connectors for the internal terminations and external outgoing connecting points Custom built as per specification and project requirement. Approved Make : Leksa/Canara/TDH

SITC of Light fixture mouting clamp Customized for suspending on fixed bars on stage Made up of Aluminium Die casted MS threaded T bolt with yellow passivation finish Complete with black powder coating matt black finish. Safe working load 150 KG Suitable to Batten of size 30 OD to 60 OD . Approved Make : Leksa/Canara/TDH

SITC of Light Fixture dual safety Chain made up of GI wire rope Bundled and twisted together Having load bearing capacity above 200 Kgs Sleve on the rope. Carabiner Clip. Approved Make : Leksa/Canara/TDH

SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 15 0 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dessipation provided with lid.Three Mtrs Length Approved Make : Leksa/Canara/TDH

Wiring for stage luminaries: Supply and wiring of stage luminaries with 3 core 2.5sq.mm flexible cable or DMX cables run inside the Cable tray/ conduits with Termination at the Dimmer Control Panel.

Power Box in metal sheet with 3 Pin Power Socket to be welded on Light Bar

Stage side ladders for mounting stage luminaries made of 50x25mm, 18G MS tubes welded in required size with Clamps.

SITC of Front of House winch Spension System Motorizedd bars

SITC of Front of House winch Spension System Motorizedd bars 500 kg stage

SITC of LED Step Light, Colour RED/Blue 1 mtrs with power supply

Providing and fixing push back type auditorium chairs with following specifications:Supply and Fixing of Auditorium with Synchronized Push back Chair with Ergonomically designed Poly Urethane foam for seat and back made by High Pressure moulding technology to achieve long life performance, upholstered with stitched 3 Layer 100% Yarn Dyed fabric Upholsteries. Chair profile with the seat in Normal position and without a tablet arm should not be more than 70 cm. The Below Structure for Pushback mechanism should be clean and creating clear Space of 8” from the floor for easy cleaning purpose. Chair pushback mechanism should consist of 2 nos. x DIA 50 mm ZYTEL/ Poly Propylene Based Rollers with Orbital Riveted links. The pushback movement is achieved by synchronised movement of 04 links. The Seat Size should be 46 cm x 48 cm the Back height should be 100 cm with ergonomically designed seat and back cushions. Chair should be available in 21”, 22” to use multiple seat size in one layout for matching variable arch length. Approved Make THEATRE SOLUTIONS (TSI), NILKAMAL, WIPRO, GEEKEN, GODREJ, HNI, STEELCASE, HAWORTH.

Providing and fixing of Cut Pile (High Density Carpet) with 100% solution Dyed Polypropylene Yarn. Carpet Weight: 1750 g/m2. Having primary Backing: 100% Polypropylene Woven Fabric. Secondary Backing: 100% Poly. Non Woven Felt backing. Tufting Gauge: 1/10". Carpet Tickness: 10mm +- 5%. Width 4m-13 ft and underlay of 6mm thick PU foam fixed to existing levelled floor with synthetic adhesives as approved by the manufacturer.

Fabricating and fixing on site 50mm thk acoustic sound reducing doors made with 2nd class Wooden framework, infill in 24 kg/ cum density resin bonded glasswool with 12mm commercial ply and 1mm thick laminate on both sides . Cost includes Sal wood Chowkhat (section size : 5" x 3") fixing acoustical seals ,stainless steel ball bearing hinges,door closers, door stoppers and s/steel handles.

Two-Way Line Array Loudspeaker System: Power Rating 800 W / 1600 W / 3200 W, Frequency Range (-10dB) 57 Hz - 20 kHz, Crossover Frequency 132 dB SPL peak 1.2 kHz, Maximum SPL (1m) 130 dB SPL peak (passive mode), LF: 130 dB HF: 139 binominal Impedance Passive = 8 ohm.

Two Way Wall Speakers: Compact Indoor/Background/Foreground Speaker, Maximum SPL (1m) 110 dB ave. Continuous Pink Noise (116 dB peak), Sensitivity 90 dB, 1W/1m (ave. 100 Hz – 10 kHz), Coverage Angle 100° x 100°. Power handling 100 Watts.

18 in. High Power Subwoofer: Power Rating 800 W / 1600 W / 3200 W,Frequency Range 31 Hz – 220 H,Frequency Range (-10dB) 31 Hz – 220 Hz, Recommended Crossover Frequencies 80 Hz, 24 dB / octave HPF80 Hz, 24 dB / octave LPF System Maximum SPL 130 dB SPL peak System Sensitivity (1w @ 1m) 95 dB SPL,Nominal Impedance 8 ohms.

Two-Way Stage Monitor : 15 Inch Two-Way Stage Monitor, 50° x 90° nominal coverage, Bi-amplified or full-range passive operation, Frequency Range (-10 dB): 60 Hz - 20 kHz,Coverage Pattern: 50° x 90° nominal, Frequency Response (±3 dB): 70 Hz - 20 kHz,Power Rating: Passive Full-Range 800 W / 1600 W / 3200W, 2 hrs1, Maximum SPL: 127 dB SPL continuous (133 dB SPL peak)2, System Sensitivity (1w @ 1m): 98 dB SPL, Nominal Impedance: 8 Ohms.

Two Way Speakers: 12" Two-Way for Balcony Loudspeaker System,Power Rating, Pink Noise 300 W / 600 W / 1200 W (Continuous/ Program/ Peak), Maximum SPL (1m) 126 dB SPL peak, Nominal Impedance 8 ohms.

Dual Channel Power Amplifier:Two-channel, 2100W @ 4Ω Power Amplifier, Sensitivity-1.4V, Rated Power Output (per channel)-3000W 2Ω, 2100W 4Ω, 1200W 8Ω Signal to Noise Ratio (below rated 1 kHz power at 8 ohms)103 dB (A-weighted) THD-< 0.5%,Frequency Response (at 1W, 20 Hz - 20 kHz), + 0 dB, -1 dB Crosstalk (below rated power).

Two-channel, 500W Power Amplifier : Channels : 2, Sensitivity : 1.4V, Rated Power Output (per channel) : 700W 2Ω, 500W 4Ω, 275W 8Ω, Signal to Noise Ratio (below rated 1 kHz power at 8 ohms) : 100 dB (A-weighted), THD : < 0.5%,Frequency Response (at 1W, 20 Hz - 20 kHz) : + 0 dB, -1 dB, Crosstalk (below rated power) 20 Hz to 1 kHz : >70 dB.

Power Amplifier : Two-channel, 800W @ 4Ω Power Amplifie, Rated Power Output (per channel) 1000W 2Ω, 800W 4Ω, 475W 8Ω , Signal to Noise Ratio (below rated 1 kHz power at 8 ohms)1&00 dB (A-weighted), Sensitivity 1.4V, THD < 0.5%, Frequency Response (at 1W, 20 Hz - 20 kHz)&+ 0 dB, -1 dB,Crosstalk (below rated power) 20 Hz to 1 kHz >70 dB.

Mixing Console : 32-Channel Premium Mixing Console, 24 Mic Inputs with 48V Phantom Power and HPF per Channel, 32 Line Inputs (24 mono and 4 stereo), 6 AUX Sends + 2 FX Sends, 4 GROUP Buses + ST Bus, 2 Matrix out, 1 Mono out.

Digital Signal Processor : INPUT PROCESSING-dbx Compression, AFS™ (Advanced Feedback Suppression), 31-Band Graphic EQ, 12-Band Parametric EQ (with narrow notch capabilities), Subharmonic Synthesis, Backline Delay, Noise Gate OUTPUT PROCESSING: Crossover (supports full range up to mono 6-way systems), 12-Band AutoEQs (8 AutoEQ bands, 4 User bands), dbx Compression, Automatic Gain Control, Subharmonic Synthesis Noise Gate, Tower Delays (up to 1000ms per output), 8-Band Parametric EQs (used for speaker tunings), dbx Limiting,Driver Alignment Delays.

Wireless Handheld Microphone : Wireless Vocal System combines professional-quality sound with simple setup and up to 14 hours battery life for legendary audio performance right out of the box. The system includes tabletop single-channel receiver, legendary handheld transmitter, microphone clip, power supply, 2 AA batteries, and user guide.

Wireless Collar Microphone : Wireless Presenter System combines professional-quality sound with simple setup and and up to 14 hours battery life for great audio performance right out of the box. The system includes tabletop single-channel receiver, CVL lavalier microphone with bodypack transmitter, lavalier clip, power supply, 2 AA batteries, windscreens, and user guide.

Gooseneck Microphone :18” (45.7 cm) Gooseneck Microphone with inline preamp,Cardioid polar pattern with tailored response for speech,Dual-section gooseneck enables ease of positioning and placement options with Base.

Dynamic Vocal Microphone :Frequency response tailored for vocals, with brightened midrange and bass rolloff, Uniform cardioid pickup pattern isolates the main sound source and minimizes background noise, Frequency response: 50 to 15,000 Hz.

Dynamic Instrument Microphone : Cardioid dynamic instrument microphone offers clean reproduction of amplified and acoustic instruments., Frequency response: 40 to 15,000 Hz.

Corded Vocal Microphone : General Purpose Vocal/Instrument Microphone with On/Off Switch & transportation Case.Total Set of Three microphones.

Powered 8-inch Control Room Loudspeaker : 8" Loudspeaker of optimizing sound, dbx AFS2 Automatic Feedback Suppression stops feedback before it starts, One-touch ducking automatically lowers music volume when speech input is detected, Wide frequency response: 54 Hz – 20 kHz, Max SPL: 124 dB, Lightweight design: 17.4 lbs, Wattage: 1,300W, 2 XLR/TRS combo input jacks and 1 XLR out offer a range of connectivity choices.

Supply of Digital Podium, with inbuilt 19" interactive panel with motorized tilting of panel, top connection panel with connectivities such as power for external laptop, VGA input, vga swicther for toggling between visualizer, cpu and external laptop, usb ports for connecting external pen drive directly to the cpu, with builtin CPU.

Supply of Floor mount box for microphone connectivity (2 x XLR in).

Supply of Floor mount box for Monitor Speaker (1 xXLR) .

Supply of 42U Equipment Rack, with locking facility, doors, fan, power strip.

Supply of Two Core Speaker Cable - 1.5 Sqmm in PVC conduits.

Supply of Two Core Shileded Microphone Cable in PVC conduits.

Supply of 12 Core Microphone snake cable Shielded in PVC conduits.

Supply of Various Connectors and Patch cables.

Supply of Floor Standing Mic Stand Tripod Type.

Supply of Desk/Table Standing Mic Stand. Tripod Type

laser projector : Native Resolution : WUXGA (1920 x 1200), Brightness : 8600 ANSI Lumens, Contrast Ratio : 20,000:1, Max. Supported Resolution : 4K-UHD (3840 x 2160) @60Hz, Native Aspect Ratio : 16:10, Lamp Life and Type : Lamp free design. Laser light source lasts up to 20,000 hours, Display Type : Single chip DLP® Technology by Texas Instruments, Chip Size : 0.67” DMD, Throw Ratio : 9 optional lenses from 0.50:1 to 8.3 :1 throw ratio range,Zoom Ratio : Motorized, Lens Shift Range : Vertical: Bottom 50% to Top 70%, Horizontal: Left 15% to Right 15%, Offset : Motorized Lens Shift, Keystone Correction : Vertical +/-30°; Horizontal +/-30°.

Supply of Long throw Zoom Lens

Supply of 4x4 Video Switcher : Connects any of 4 HDMI sources to any of 4 HDMI displays, Supports 4K resolutions up to UHD (3840 x 2160) and DCI (4096 x 2160) with refresh rates of 30 Hz (4:4:4) and 60 Hz (4:2:0), Signaling rates up to 3.4 Gbits for fl awless 4K output, Multiple Control Methods – system management via front-panel pushbuttons, IR remote and RS-232 control.

Player: Preamp output for connecting to Stereo or Mono input of another amplifier and a REC input for recording the preamp output of another amplifier, Built-in MP3 recorder player with LCD display supplied with remote control and with built-in facility of USB, SD, MMC card & Bluetooth.

Professional 1.4V HDMI Cable, VGA cable / video cable for the projection system.

Patch cords for System Interfacing & all neccessary connectors.

Supply Rx/Tx HDMI Extender over Cat5e/Cat6 HD BaseT HDMI Extender. Frequency Bandwidth 2.97Gbps, Transmitter Input/Output Ports 1x HDMI Female port/2xCAT6, 1x IR Tx/1x IR Rx/1xPhoenix, Receiver Input/Output Ports 1xHDMI Female port/2xCAT6 1x IR Tx/1x IR Rx/1xPhoenix, Power Supply DC 12V 2.5A.

SITC of CHAIRMAN UNIT : Digital conference technology, 17 Built-in 9.7mm gold- plated capacitive pickup head mic capsules, Unique cavity and integrated forming sound pickup steel mesh design, High sensitivity sound pickup design, Built-in automatic gain AGC function, , effective sound pickup, Professional capacitive touch induction button, 150° sound pickup Angle, 48KHz audio sampling frequency,speech clear, frequency response up to 30Hz-20KHz, With three color indicator display, normal speech is red, VIP unit is green, number status is yellow, Support eight meeting modes: limited number, FIOFI, LIFO, Last in First out, Chairman's permission (request for speech), voice control start, limited time speech, queuing speech, free discussion.

SITC of DELEGATE UNIT : Digital conference technology, 17 Built-in 9.7mm gold- plated capacitive pickup head mic capsules, Unique cavity and integrated forming sound pickup steel mesh design, High sensitivity sound pickup design, Built-in automatic gain AGC function, , effective sound pickup, Professional capacitive touch induction button, 150° sound pickup Angle, 48KHz audio sampling frequency,speech clear, frequency response up to 30Hz-20KHz, With three color indicator display, normal speech is red, VIP unit is green, number status is yellow, Support eight meeting modes: limited number, FIOFI, LIFO, Last in First out, Chairman's permission (request for speech), voice control start, limited time speech, queuing speech, free discussion.

SITC of CENTRAL UNIT (CONTROLLER) : Support eight meeting modes: limited number, FIOFI, LIFO, Last in First out, Chairman's permission (request for speech), voice control start, limited time speech, queuing speech, free discussion,The number of speakers can be set to 1-9, the chairman and VIP are not limited by the number, free discussion mode is not limited to open all, With high-definition camera, automatic speaker tracking, Support the connection of 150 chairman units, With super anti-interference ability, it can effectively isolate the signal interference of mobile phone, radio wave, Bluetooth, WiFi and so on, and never produce noise when calling, It has a 3.5mm headphone interface, which can be used as a meeting monitoring for participants, and can adjust the volume of the listening.

SITC of Two Way Wall Speakers: Compact Indoor/Background/Foreground Speaker, Maximum SPL (1m) 110 dB ave. Continuous Pink Noise (116 dB peak), Sensitivity 90 dB, 1W/1m (ave. 100 Hz – 10 kHz), Coverage Angle 100° x 100°. Power handling 100 Watts.

SITC of Amplifier : Octo channel 4 Ohm energy-efficient amplifier - 8 x 30W - 70/100V, RMS/AES power handling @ 4 Ω/ @ 70 V/@ 100 V : 8 x 30 W, Signal / Noise : > 100 dB, THD+N (@ 1 kHz) : < 0.05% (1/8 rated Power), Crosstalk (@ 1 kHz) : < 70 dB, Frequency Response (± 3 dB) : 110 Hz - 20 kHz , Technology : Class- D.

SITC of Digital signal processor with min. 04AEC enabled Mic/Line inputs, 04 Line outputs or better , Input channel processing should include Pre amplifier, Signal generator, Expander, Compressor, 10 band Parametric EQ or better, Output Channel processing should include 31 band Graphic equilizer, Delay, Crossover, limiter or better, Other features should include Automatic mixing console, Ducker, Feedback elimination, Noise elimination, echo elimination or better, Should have built-in Bi directional USB for Software based VC as well as for playing digital audio, Should have built in Camera tracking Module, 8 Port Freely Configurable GPIO or better with Analog/Digital dynamic range of 114dB or better, Sampling rate of 48Khz or better, Frequency response of 20Hz – 20Khz or better, per channel phantom power module or better. Should be configurable thru software.

SITC of 98 Inch Display : Screen Size : 98 Inch, Brightness (cd/m²) 780 nits, Contrast Ratio 5000:1 , Dynamic Contrast Ratio : 700,000:1, Response Time (ms) : 6.5, Display resolution (H x V, pixels) : 3840 x 2160, HDR (High Dynamic Range) compatibility : Yes (HDR10,HLG,Dolby Vision), Aspect Ratio : 16:9, Portrait/Tilt Compatibility : Yes, Dimming type : Local Dimming, Display Device : LCD, Backlight type : Direct(Full Array LED), TRILUMINOS Display : XR Triluminos Pro, Color gamut (DCI- P3) : 95%, Picture Processor : Cognitive Processor XR, Operation time : 24/7, Haze (%) : 2%, Viewing Angle (Right/Left) : 178(89/89) degree, Viewing Angle (Up/Down) : 178(89/89) degree, Video Processing : XR 4K Upscaling , Motion enhancer : XR Motion Clarity, Speaker Position : Down Firing + Side Back, Audio Power Output: 10W + 10W + 10W + 10W, Pro mode : Yes, HDMI auto wake-up : Yes, HTML5 platform : Yes, Multicast/IPTV : Yes, Operating System : Android TV, On-board Storage (GB) : 32GB.

SITC of Wireless Presentation System (Wireless dongle) : Seamless wireless conferencing for small to medium-sized meeting and conference rooms,Full BYOD support, Remote collaboration with Button or Desktop App, Works with your device, conferencing platform & a wide range of AV peripherals, Enhanced security, connected and cloud managed, Full interactivity.

Video Conference Camera : CMOS 3.10Mega Pixel, Full HD,12Xoptical Zoom,USB3.0+IP, view Angle: 72.5 Degree,Pan: 355 Degree, Tilt:30 To +30Degree,9Preset position by remote.225 preset position by Keyboard/PC,Support H264/H.265,Control Mode- RS232,Wallmounting , Desktop,Ceiling mounting.

SITC of Wooden Conference Table for seating of 25 peoples.

Providing and fixing of Medium Back Chair

Providing and fixing of Cut Pile (High Density Carpet) with 100% solution Dyed Polypropylene Yarn. Carpet Weight: 1750 g/m2. Having primary Backing: 100% Polypropylene Woven Fabric. Secondary Backing: 100% Poly. Non Woven Felt backing. Tufting Gauge: 1/10". Carpet Tickness: 10mm +- 5%. Width 4m-13 ft and underlay of 6mm thick PU foam fixed to existing levelled floor with synthetic adhesives as approved by the

SITC of Patch Cord, Cable , Connectors & other Accessories to complete the job.

VINOD PRASAD BIJLWAN (BID ID -355968)