Renovation works for the kitchen space of NTA, NSIC Okhla

S.NO. DESCRIPTION DSR NON DSR Total Amount

Total Amount Including GST 20,24,898.00

DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

Providing and laying in position CEMENT CONCRETE of specified grade exluding

2 4.1 the cost of centring and shuttering-all work upto plinth level.

1:4:8 (1 Cement : 4 coarse sand (Zone III) derived from natural sources: 8 graded

stone aggregate 40 mm nominal size derived from natural sources

Providing and laying vitrified floor and wall tiles in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS: 15622, of approved make, in all colours and shades, laid on

20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and

1.04 11.41A matching pigments etc., complete.The tiles must be cut with the zero chipping

diamond cutter only. Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber mallet for placing

the tiles gently and easily.

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

1.05 11.21.2.1 Acid and alkali resistant tile Sqm 50 1,884.90 94,245.00

Providing and laying 60mm thick factory made cement concrete interlocking

paver block of M -30 grade made by block making machine with strong vibratory

compaction, of approved size, design & shape, laid in required colour and pattern

1.06 16.68 over and including 50mm thick compacted bed of coarse sand, filling the joints Sqm 69 972.00 67,068.00

with line sand etc. all complete as per the direction of Engineer-in-charge.

Digitally signed by AMIT

Providing and laying at or near ground level factory made kerb stone of M-25

grade cement concrete in position to the required line, level and curvature, jointed

with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or

without grooves (thickness of joints except at sharp curve shall not to more than

1.07 16.69 5mm), including making drainage opening wherever required complete etc. as Cum 3 10,117.60 31,415.15

per direction of Engineer-in-charge (length of finished kerb edging shall be

measured for payment). (Precast C.C. kerb stone shall be approved by Engineering-

Providing and applying plaster of paris putty of 2 mm thickness over plastered

3.22 13.26 surface to prepare the surface even and smooth complete. Sqm 111 262.70 29,028.35

Wall painting with premium acrylic emulsion paint of interior grade, having VOC

(Volatile Organic Compound) content less than 50 grams/ litre of approved brand

13.83 and manufacture, including applying additional coats wherever required to

3.23 achieve even shade and colour

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

6.13 designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 24 1,123.80 27,038.63

Supplying and fixing rolling shutters of approved make, made of required

size M.S. laths, interlocked together through their entire length and

jointed together at the end by end locks, mounted on specially designed

pipe shaft with brackets, side guides and arrangements for inside and

outside locking with push and pull operation complete, including the

cost of providing and fixing necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of adequate strength

conforming to IS: 4454 - part 1 and M.S. top cover of required thickness

for rolling shutters.

80x1.20 mm M.S. laths with 1.20 mm thick top cover

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat

Digitally signed by AMIT

12 mm cement plaster

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

3.02 9.1 fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood cu m 0.10 1,42,949.70 14,866.77

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

non-decorative type, core of block board construction with frame of 1st class hard

3.04 9.21 wood and well matched commercial 3 ply veneering with vertical grains or cross

bands and face veneers on both faces of shutters:

35mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

3.05 9.23 on all edges of flush door shutters (over all area of door shutter to be measured). Sqm 3 462.35 1,165.12

Providing and Fixing 1236-22X922 mm Dtype Handle Material : Stainless Steel.

Finish : Satin Stainless Steel (SSS). of approved make and model all complete as per

the direction of Engineer-in-charge.

Providing and Fixing SS Mortise Lock Body SB/TB for door thickness 25-50 mm for

3.07 MR wooden doors of approved make and model all complete as per the direction of Each 1 895.62 895.62

Engineer-in-charge.

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with

10mm diameter bolts, nuts and wooden plugs and embedding in cement

3.09 9.53 concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded

stone aggregate 20mm nominal size).

Providing and fixing precoated galvanised iron profile sheets (size, shape and

pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %)

total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet should have protective guard film of 25

microns minimum to avoid scratches during transportation and should be

4.01 12.50 supplied in single length upto 12 metre or as desired by Engineer-in-charge. Sqm 20 738.65 14,403.68

The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55

mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including cutting to

size and shape wherever required.

Digitally signed by AMIT

Steel work in built up tubular (round, square or rectangular hollow tubes etc.)

trusses etc., including cutting, hoisting, fixing in position and applying a priming

10.16 coat of approved steel primer, including welding and bolted with special shaped

washers etc. complete.

10.16.2 Hot finished welded type tubes Kg 451.11 194.40 87,695.78

Providing and laying in situ five course water proofing treatment with APP

(Atactic Polypropylene) modified Polymeric memberane over roof consisting

of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding

material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/ 25

conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric

membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers

prefabricated with centre core as 100 micron HMHDPE film sandwiched on both

14.87 sides with polymeric mix and the polymeric mix is protected on both side with 20

micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class

designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with

2% integral water proofing compound by weight of cement over a 12 mm layer of

cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick

tiles shall be paid for separately)

Steel work welded in built up sections/ framed work, including cutting, hoisting,

10.25 fixing in position and applying a priming coat of approved steel primer using

structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing rectangular high density polyethylene water storage loft tank

with cover, conforming to ISI : 12701, colour of opaque white or as approved by

18.48A Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & per litre 5000 11.00 55,000.00

over flow pipes. The base support i/c fittings & fixtures for tank shall be paid

Providing and fixing 12mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top & bottom

pivot & double acting hydraulic floor spring type fixing arrangement and making

21.18 necessary holes etc. for fixing required door fittings, all complete as per direction of sqm 3 5,325.90 13,421.27

Engineer in charge (Door handle, lock and stopper etc. to be paid separately)

providing frame support to glass door and other accoserries like Door handle, lock

and stopper etc. as per direction of EIC.

Glass partition : Glass partition of thickness 12 mm , inclusing of providing & fixing of hardwares

& other harwares as per the requirement of site , complete in all respects .

Digitally signed by AMIT

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias

and similar locations of required size, approved shade, colour and texture laid over

8.2 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment, epoxy touch ups, including rubbing,

curing, moulding and polishing to edges to give high gloss finish etc. complete at

8.2.2 Granite stone slab colour black, Cherry/Ruby red

8.2.2.2 Area of slab over 0.50 sqm sq.m 8 5,136.30 41,604.03

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of

neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate sq.m 8 614.20 4,975.02

Extra for providing opening of required size & shape for wash basin/ kitchen sink in

kitchen platform, vanity counter and similar location in marble/ Granite/ stone

8.5 work, including necessary holes for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete.

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1

11.29 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an

admixture of pigment to match the shade of stone.

SHELVES:- Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle

board or graded wood particle board IS : 3087 marked, with one side decorative and other side

9.18 balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and

fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid

Providing fitting for shelves(door handles, hinges, etc.) for all shelves. LS 1 4,000.00 4,000.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES-KITCHEN

DESCRIPTION AMOUNT AMOUNT

S NO DSR/ MR 2023 Unit QUANTITY RATE

DSR ITEM NON DSR ITEM

Supply, Installation, Testing and Commisiong S.S. STORAGE RACK -5 SHELVES (ss) of

900X450X1800 6 Rack having 5 nos of shelves made in 18 swg SS 304 sheet, all

supported on 4 nos vertical pipes of 38x38mm x 16 swg square SS 304 pipes with SS

adjustable feets. Custom Made and as directed by engg-in-charge at site.

Supply, Installation, Testing and Commisiong DEEP FREEZER 300 Ltr. f SS 304

Welded Construction Four Shelves Rack for Storage of Vegetables & Fruits at 5˚C

2 MR Shelves made from 1.5mm Thk SS 304 Sheet, main frame made from SS 304 40 X 40 Each 1 26,910.00

X 1.5mm Thk Sq. Tube. All Welded

joints to be duly ground & smoothly finished, complete Rack to be finished to 400 26,910.00

Grit MattInstallation,

Supply, Finish and as directed

Testing andbyCommisiong

engg-in-charge at site.

FOUR DOOR REF 1200X750X2000

Large storage area, 1430 ltrs, suitable to contain 2/1 GN grids or shelves on anti-tilt

runners. Operating temperature can be adjusted from -2 to +10 °C to suit different

food storage requirements. Performance guaranteed at ambient temperatures of

3 MR +43°C. Double walled cabinet, exterior and interior made of SS 304. 39 Cabinet Each 1 1,72,500.00

fitted with up to 75 mm thickneSS of cyclopentane insulation for best insulating

performance with 100% environmental protection. Shall be provided with locking

provision. Shall be provided with 4 nos of adjustable shelves and as directed by engg-

in-charge at site. 1,72,500.00

Supply, Installation, Testing and Commisiong PUFFER PLATE 1500X650X850 The

equipment shall have 5 nos "V" type burners of 40,000 BTU/hr capacity with 5

individually controlledgas valve at front panel. There shall be 5 pilot burners

controlled by a 3 valve at the front panel. Plate shall be made of 16 mm thick

polished MS plate. Front of the top shall be in 16 GA SS 304 with 150mm high back

4 MR splash. There shall be all round panelling upto 300mm from top, front panelling in Each 1 62,100.00

18 swg SS 304 and back & both side panelling in 20 swg SS 304. 3 nos of puffer plate

shall be of size 225x225 mm. The bottom shelf having frame of 38x38mm 16 swg SS

202 square pipe with 12mm dia SS 202 tube on 75mm distance from cetre to centre

of the pipe. The equipment is supported on 6 legs of 38mm dia x 16 ga SS 304 pipe

with adjutstable feets and as directed by engg-in-charge at site. 62,100.00

Supply, Installation, Testing and Commisiong EXHAUST HOOD OVER PUFFER PLATE

with required ducting 1800X750X500 and The wall type hood shall be made in 18

swg SS 304. The hood shall have 2 nos 500x500x50mm thick SS 304 baffle type

5 MR filters with handle. There shall be 4 nos of 14 ga SS brackets to hang the hoods from

ceiling. For illumination, there shall be 2x40-220v-1ph tubelights fitted in the hood.

Size of opening of the duct shall be as per consultant and as directed by engg-in- 41,400.00

charge at site.

Digitally signed by AMIT

Supply, Installation, Testing and Commisiong DOUGH KNEADER MACHINE CAP-

20KG Size of 720x1510x1050 Bowl of capacity 20kg atta shall be made of Stainle SS

Steel 304. Motor shall be of 2 HP of make, crompton greaves. Electric load shall be 2

hp- 440v-3 ph. and as directed by engg-in-charge at site. 71,760.00

Supply, Installation, Testing and Commisiong TWO BURNER RANGE

1200X600X850+150 Twin burner range with one high speed burner and one low

speed burner in SS 304 work table with framework of square pipes of

38mmx38mmx1.5mm. Table top with SS 304 with 100 mm of back wall to the top

shelve, all with 16 SWG with under shelve MS angle framework of 35mm x 35mm x

3 mm thick. Under shelf to be of 18 SWG. (LxBxH) 38,640.00

STOCK POT STOVE 600X600X600 SS 304 Single Stock Pot Gas Stove, with powder

8 MR coated top surface finish. (LxBxH) 600X600X600 and as directed by engg-in-charge Each 3 21,390.00

at site. 64,170.00

Supply, Installation, Testing and Commisiong SS EXHAUST HOOD WITH FILTER OVER

STOCK POT STOVE SPARE 2500X750X500 with required ducting The wall type hood

shall be made in 18 swg SS 304 in 3 equal halves joined with SS bolts and nuts. The

hood shall have 9 nos 500x500x50mm thick SS 304 baffle type filters with handle.

There shall be 4 nos of 14 ga SS brackets in each halves to hang the hoods from

9 MR ceiling. For illumination, there shall be 6 nos of 2x40-220v-1ph tubelights fitted in Each 1 57,960.00

the hood. 150mm wide fresh air grills of powder coated Aluminium shall be

provided in the hood through out the length. Fire suppreSSion system, of make-

ceasefire, ansul

or amrex, shall be provided in hood. It should have adequate no of nozzles to cover

all the kitchen equipment under the hood. Size of opening of the duct shall be as per 57,960.00

Supply, Installation, Testing and Commisiong POTATO PEELAR 15KG Size

of dia 400+180x945 shall be of vertical design suitable for mounting on

the floor. Machine shall be divided intwo sections, Top peeling aSSembly

and the bottom for motor drive housing, all made of StainleSS Steel. The

peeling time shall be between 1-3 minutes per charge, depending upon

the grade and size of potatoes. Motor shall be of 1 HP- 220V-1ph,

enclosed in the extended base of machine. Abrasive Disc shall Nos 1.00 -

21 Days 34 potatoes. Motor shall be of 1 HP- 220V-1ph, enclosed in the

extended base of machine. Abrasive Disc shall operate at the speed of

400rpm, bonded with carborundum abrasive. On removal of hopper, disc

should be removed easily for maintenance and cleaning. Material of

Construction: - Top and Body – 16 swg SS, Peeling disc – 14 swg SS,

Discharge door and aSSembly- aluminium. There shall be 12mm Water

inlet, 1m of ¾ core cable and starter. and as directed by engg-in-charge 55,890.00

Digitally signed by AMIT

Supply, Installation, Testing and Commisiong PULVERIZER Size of

500+65x370x680 2 HP MOTOR -220 VOLT 50HZ, S.S. PANELING, HEAVY

DUTY S.S. ROTOR BLADE DIRECTLY CONNECTED TO THE MOTOR AND

HOUSED IN S.S. CRUSHER HOUSING S.S. TRAY ON TOP WITH FEEDING

HOLE 2 SETS OF WIRE MESH SIEVES LEDGES BELOW FOR PLACING GN

PAN RECEPTACLE. and as directed by engg-in-charge at site. 24,840.00

Supply, Installation, Testing and Commisiong BULK TROLLEY Size of

600X900X900 Having platform size of 600x900 mm of SS 304, with

40mm wide collar all around, supported by SS angle frame. The handle

12 MR shall be made of 25mm dia SS 304 pipe having shape and size. The trolley Each 1 25,944.00

shall move on 4 nos 125mm dia x 32mm wide PU made swivel type

rubber tired castor, having brakes on 2 castors. C10:C11 Trolley to be

provided with Set of Fixed & Lackable and as directed by engg-in-charge 25,944.00

at site. Installation, Testing and Commisiong Folding Tables

1.5*0.75*0.9 SS 304 sheet, all supported on 4 nos vertical pipes of

38x38mm x 16 swg square SS 304 pipes with SS adjustable feets. Custom

Made and as directed by engg-in-charge at site. 50,000.00

Stainless Steel, Commercial Cooking Range, individual needle control valves for main burners and pilot flames,stainless steel drip trays,stainless

steel bullet feet, SS/cast iron grates

TWO BURNER RANGE

PUFFER PLATE FULL SS 304 .TOP 16 SWG,SIDE CLOSE & DEEP TRAY 20 SWG, MS 12 MM PLATE & PUFFER PLATE WITH NCV.HEAVY DUTY RV BURNER .LEGS

1500X650X850 40X40MM SQUARE TUB WITH TEPLON ADJUSTABLE BULLET with warantee and guarantee certificate

FULL SS 304 GRADE , INER &OUTER SS 20 SWG,PUFF INSULATION, COMPRESSOR WITH TEMPRATURE DIGITAL DISPLAY From standard make with

FOUR DOOR REF warantee and guarantee certificate

Fully Automatic, Stainless Steel Body , 100% copper binding Motor, capacity 20 Kg, Motor Power 4 Hp and Above, Automatic Spiral Dough Mixer

DOUGH KNEADER Machine with waranty and guarantee certificate

MACHINE CAP- 20KG

PULVERIZER 2 HP Stainless steel body ,2 hp with 100% copper binding, power 230 V, single phase.

Automatic Defrost, capacity - 300 ltr, Dual Door, High Density PUF thickness of 70mm to avoid leakage of cold air outside , 5 star Rated for energy

DEEP FREEZER 300 Ltr. saving from standrd makes available in the market with the waranty and guarantee certificate

Note:- The Specification for above mentioned kitchen equipment are tentative and the bidder has to submit atleast three samples for each above items and the kitchen

equipment finalised by the NTA/NSL officials needs to be provided by the bidder within its quoted rates

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO TOTAL AMOUNT TOTAL AMOUNT

DSR NO TOTAL AMOUNT TOTAL AMOUNT

DESCRIPTION UNIT QUANTITY RATE

DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface / recessed medium

class PVC conduit, with modular switch, modular plate, suitable GI box and earthing

A.1 the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq.

A.3 1.12 mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. Metre 45 334.00 15,030.00

Supplying and fixing following modular switch/ socket on the existing modular plate &

1.24 switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 5 122.00 610.00

1.24.5 6 pin 15/16 amp socket outlet Each 15 197.00 2,955.00

A.5 Supplying and fixing modular blanking plate on the existing modular plate & switch

1.26 box excluding modular plate as required. Each 0 40.00 -

Supplying and fixing following size/module, GI box along with Modular base & cover plate

1.27 on existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

1 FR PVC insulated copper conductor, single core cable in surface/ recessed medium class

B.1 PVC conduit

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 25 275.00 6,875.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 100 334.00 33,400.00

Supplying and fixing of following sizes medium class PVC conduit aong with accessories

1 in surface/ recess including cutting the wall and making good the same incase of recessed

conduit as required

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

2 breaker suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Digitally signed by AMIT

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel,

MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes

D.5 in the existing MCB DB complete with connections, testing and commissioning etc. as

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts,

residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and commissioning etc. as

MR SITC of LED Tube/ Batten Lights of 36W, Sleek 4ft lenght Each 8 1,250.00 10,000.00

MR SITC of 50W LED flood light for outer area with minimum IP66 rating Each 4 2,210.00 8,840.00

SITC of 35 litres geyser including all the fittings, piping, connection, complete in all respect

MR SITC of 6 Kg CO2 type fire entiguisher Each 1 14,700.00 14,700.00

MR SITC of 6 Kg ABC type fire entiguisher Each 1 13,500.00 13,500.00

MR SITC of WALL FAN (400mm Sweep) Each 5 3,000.00 15,000.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DESCRIPTION TOTAL TOTAL

S NO DSR NO UNIT QUANTITY RATE

Supply, Installation, Testing and Commisioning of SINGLE LEVER

CONCEALED BASIN MIXER (WALL MOUNTED) WITH SPOUT

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per

IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting

Kitchen sink without drain board

610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.

waste fittings complete.

6 17.28.2 Flexible pipe

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of

approved quality conforming to IS : 8931

9 18.53.1 15 mm nominal bore EACH 6 574.30 3,445.80

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings, including fixing the pipe with clamps at 1.00 m spacing.

This includes jointing of pipes & fittings with one step CPVC solvent cement

and testing of joints complete as per direction of Engineer in Charge.

11 Internal work - Exposed on wall -

12 18.7.3 25mm nominal outer dia pipes METRE 10 401.55 4,015.50

13 18.7.1 15mm nominal outer dia pipes METRE 5 286.80 1,434.00

14 18.7.4 32mm nominal outer dia pipes METRE 10.682 518.75 5,541.29

Digitally signed by AMIT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This

15 18.8 includes jointing of pipes & fittings with one step CPVC solvent cement and -

the cost of cutting chases and making good the same including testing of

joints complete as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.,

17 18.8.1 15mm nominal outer dia pipes METRE 10 497.80 4,978.00

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

The Pipes will be supported with threaded G I rods & U clamps with nuts,

washers etc on 50x50x5 mm slotted angle. The cost will include all support

arrangements. The work includes commissioning of all pipes lines as per

drawings and specifications and as directed by engg-in-charge at site.

21 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 3 525.62 1,576.86

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC

pipes of min 6 Kg/ Sqcm rating with fitting for waste pipe from fixtures to

floor trap including reduces, enlarger, socket, couplers, bends, tees etc

including fixing at wall/ ceiling level supported by clamp & hangers etc.

cutting holes in wall/ floors/ slabs and making good the same with cement

concrete 1:2:4 complete as required.

24 Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 4 536.00 2,144.00

Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating

over floor traps.

Digitally signed by AMIT

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and

flat round cover with screws and other required fitting complete as required.

Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER

Material: Stainless steel, brass with chrome plating, or high-quality plastic,

wall-mounted, drainage holes, chrome or brushed nickeand as directed by

engg-in-charge at site.

Supply, Installation, Testing and Commisiong of ROBE HOOK Material:

Stainless steel, brass with chrome plating, or high-quality plastic, wall-

mounted, drainage holes, chrome or brushed nicke and as directed by engg-

in-charge at site.

Supply, Installation, Testing and Commisiong of TOWEL HOLDER (bars, rings,

or racks) Material: Stainless steel, brass with chrome plating, or high-quality

plastic, wall-mounted, drainage holes, chrome or brushed nicke and as

directed by engg-in-charge at site.

Supply of 50-liter dustbin with dual compartments (50 liters each for wet

and dry waste) Material: High-density polyethylene (HDPE) or stainless steel

Features: Foot pedal-operated lids, removable inner bins, color-coded

compartments, Placement and leveling of dustbin at specified locations

smooth operation of foot pedals and lids, stability check when loaded and as

directed by engg-in-charge at site.

Providing, laying and jointing glazed stoneware pipes class SP-1 with

31 19.1 stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 meter 15 443.60 6,654.00

fine sand) including testing of joints etc. complete :

32 19.1.1 100 mm diametre

Total Amount 38,586.14 49,219.86

Total Amount 38,586.14 49,219.86

Digitally signed by AMIT