Loading
Loading…
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹1.7 Cr
EMD Value
₹2.3 L
Closing Date
28 Jul 2025, 3:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
TRD/WORKS
14 conditions · 3 needing a document upload
Special Financial Criteria:- The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees, N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Special Technical Criteria:- The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value o f the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Similar nature of work is " Supply, installation, testing and commissioning of any LT/HT Electrical work." (As per CEE/MLG/NFR's L/No.- EL/W/29/Tender/similar works/2281, dated- 28.09.2010)
73 conditions · 12 needing a document upload
The following documents should be specified for submission along with tender:- a) List of Personnel, Organization available on hand and proposed to be engaged for the subject work. b) List of Plant & Machinery available on hand (own) and proposed to be inducted (own and hired to be given separately) for the subject work. c) List of works completed in the last three financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work, Date of actual start, actual completion and final value of contract should also be given. d) List of works on hand indicating description of work, contract value approximate value of balance work yet to be done and date of award. e) Valid electrical contractor's license issued by the State Govt., f) Supervisory License issued by the state Govt. g) Name of the Engineer/ Diploma holder:- (i) One qualified Graduate Engineer when the cost of the work to be executed is rupees two hundered (200) lakhs and above & (ii) One qualified Diploma Holder (Engineer) when the cost of the work to be executed is more than rupees twenty five (25) lakhs, but less than rupees Two hunderd (200) lakhs.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Electrical General work in connection with "Proposal for construction of Road over Bridge in lieu of Level Crossing No. NC-5 (Manned) at Km 7/9-8/0 between station Rangapani-New Jalpaiguri in New Jalpaiguri-Aluabari Section."
EL_GEN_27_25-26
EL_GEN_27_25-26
Open
Works - General
12 Months
Katihar, Bihar
₹0
₹2.3 L
28 Jul 2025
3 Jul 2025
45 items across 1 schedule · ₹1,69,64,081.76 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | "Supply & testing of GI octagonal pole 6 mt long with foundation bolt, loop box of bakelite sheet with one 6A SP MCB and 16 sq mm stud type connector etc. The octagonal pole shall be hot dip galvanized in single dip. Technical specification of pole as following:- Height - 6 mt Top dia (A/F) - 70 mm Bottom dia (A/F) - 130 mm Sheet thickness - 3 mm Base plate (L x B x T) - (200 x 200 x 12) mm Foundation Bolt size (no.x dia) - 4 x 20 dia mm Pitch Circle Dia (PCD) - 200 mm Bolt length - 600 mm Projected Bolt Length - 100 mm . " | Numbers 160.00 | — | 12,942.07 | 20,70,731.2 |
| 2 | Supply & fixing of 1 mtr GI Single arm bracket (header) and holder with Nut & bolt | Numbers 160.00 | — | 1,487.34 | 2,37,974.4 |
| 3 | Erection of Street light pole (Octagonal pole) with CC foundation including digging & refilling of earth to a suitable height above ground level in ratio 1:3:6 by cement sand & Chips 19 mm & down including excavation of earth including fixing of SA/DA bracket etc. | Numbers 160.00 | — | 1,431.72 | 2,29,075.2 |
| 4 | Supply, installation, testing & commissioning of 100 watt LED street light luminaire with heat resistant glass with connecting lead (IP protection- IP 66 class-I, System efficacy>=105 lm/w, Housing- Pressure die cast aluminium powder coated, THD<10%, p.f.>0.95, Surge protection- 5 kV) as per instruction of Engineer incharge at site. | Numbers 170.00 | — | 11,000 | 18,70,000 |
| 5 | Supply, fixing, testing & commissioning of IP 66/67 thermoplastic cable junction box / loop box of size (210 x 310 x 116) mm with knockouts & 04 nos terminals | Numbers 160.00 | — | 5,005.54 | 8,00,886.4 |
| 6 | Supply, laying, commissioning & testing of HDPE pipe 110 mm dia PN-6 grade to be laid partly along the pole /underground with suitable fixing arrangement by MS clamp made of MS flat of size 50x6 mm and suitable size nut , bolt, washer and required bend, joints. | Metre 2500.00 | — | 351.49 | 8,78,725 |
| 7 | Supply, erection, testing ,commissioning & painting of Wall/floor mounted powder coated cubicle panel board (Modular look), outdoor type with double door made of suitable size MS/GI angle 50 x 50 x 6 mm, MS/GI flat 50 x 6 mm, 14 SWG MS sheet/Powder coated CRCA sheet with provision of weather proof,rust proof,dust proof,water proof having internal rubber gasket and connection by suitable size copper strip. | Set 2.00 | — | 12,947 | 25,894 |
| 8 | Copper bus bar 100 amps made of electrolytic grade copper consisting of 4 bars ( 3 Ph and Neutral ) ( Bus bar should have insulation cover) | Set 4.00 | — | 820.65 | 3,282.6 |
| 9 | MCCB FP 63 amps, 25 kA, Ics=100% Icu | Numbers 2.00 | — | 6,762.03 | 13,524.06 |
| 10 | Supply, installation and testing of Astro (Analog) time switch with 3 pole 63 amp contractor and suitable thermoplastic box and fitted on mounting plate/DIN rail. | Set 4.00 | — | 9,002.83 | 36,011.32 |
| 11 | MCB TP 63 A, 10 kA, C-curve as per IS/IEC 60898-1 2002 | Numbers 4.00 | — | 2,358.71 | 9,434.84 |
| 12 | MCB SP 6-32 amps, 1 module, 10 kA, C-curve Conforms to IS/IEC 60898 - 1:2002 (For light/Fan/6 Amp Plug point circuit) (6-10 Amp- 8) | Numbers 16.00 | — | 223.03 | 3,568.48 |
| 13 | Cutting of Road/ Pucca/ hard soil below (0.3 X 1) mt from ground level and make it good as original with supply & execution of CC work (1:3:6) as per instruction of Engineer incharge at site. | Metre 1600.00 | — | 273.62 | 4,37,792 |
| 14 | Supply , erection, testing & commissioning of 16 mt long High Mast Tower with 8 nos. x 250 watt LED luminaries in symmetrical arrangement complete with all accessories (Double drum winch, SS wire rope, integral power tool motor, head frame, junction box, foundation bolt, LED aviation light, Fedder pillar with single dial timer & raising lowering mechanism etc.) including shallow foundation with M20 grade concrete etc. as per instruction of Engineer Incharge at Site. | Set 4.00 | — | 6,75,000 | 27,00,000 |
| 15 | Supply, installation, testing & commissioning of 160 watt LED flood light luminaires complete with pressure die cast aluminium housing, IP 66, Luminous efficacy>= 100 lm/watt with heat sink feature, surge protection etc including wire connection as per instruction of Engineer incharge at site. | Numbers 40.00 | — | 19,570 | 7,82,800 |
| 16 | Supply & erection of earth by 80 mm dia 3 Mtr. Long (medium) GI earth electrode, 8 SWG GI wire, GI nuts, bolts including masonry materials for earthing pit, salt, charcoal etc and construction of earth pit covered with cement concrete plate having locking arrangement and watering pipe as per drg. No.- CEE/STD/1. | Numbers 40.00 | — | 2,572.41 | 1,02,896.4 |
| 17 | Supply, erection & commissioning of earth spike made of 16 mm dia 1.8 mt long GI rod & connection metal body with the earth spike rod by 6 SWG GI earth wire with nut, bolt & washer etc | Numbers 20.00 | — | 314.16 | 6,283.2 |
| 18 | Supply , & fixing o f GI earth bar by MS clamp made of MS flat of size 50x6 mm and suitable size nut , bolt, washer etc as per instruction of Engineer Incharge at site. | Metre 4000.00 | — | 64.16 | 2,56,640 |
| 19 | Supply, installation, testing & commissioning of oudoor type weather proof sheded feeder pillar box of suitable size made of powder coated 14 SWG MS/CRCA sheet, angle, flat etc. The feeder pillar box four legs should be grounted on CC foundation (1:3:6). Cable entry should have PVC glands. Feeder pillar box should have double door system with locking arrangement with fixing of rubber gasket for protection of entry of dust and water alongwith supply and fixing of following MCCB as per instruction of Engineer Incharge at site. | Set 4.00 | — | 4,650.9 | 18,603.6 |
| 20 | MCCB FP 200 amps, 36 kA, Ics=100% Icu | Numbers 4.00 | — | 13,576.85 | 54,307.4 |
| 21 | Copper bus bar 100 amps made of electrolytic grade copper consisting of 4 bars ( 3 Ph and Neutral ) ( Bus bar should have insulation cover) | Set 4.00 | — | 820.65 | 3,282.6 |
| 22 | MCCB FP 63 amps, 25 kA, Ics=100% Icu | Numbers 24.00 | — | 6,762.03 | 1,62,288.72 |
| 23 | Supply, Fixing & Testing of LED multifunction meter, Accuracy Class 1.0, Input voltage measurement range 50-550 VAC (P-P), Aux supply 90-300VAC/DC for measuring of V, A, F, PF, kW, kVA, kVAR, kWh, kVAh, kVARh, Runhours, On hours, Interrupts, THD, neutral current etc parameters alongwith supply & fixing of 3 nos. suitable CTc. | Set 4.00 | — | 9,640.93 | 38,563.72 |
| 24 | Supply, installation, testing & commissioning of oudoor type weather proof sheded feeder pillar box of suitable size made of powder coated 14 SWG MS/CRCA sheet, angle, flat etc. The feeder pillar box four legs should be grounted on CC foundation (1:3:6). Cable entry should have PVC glands. Feeder pillar box should have double door system with locking arrangement with fixing of rubber gasket for protection of entry of dust and water alongwith supply and fixing of following MCCB as per instruction of Engineer Incharge at site. | Set 2.00 | — | 4,650.9 | 9,301.8 |
| 25 | MCCB FP 100 amps, 25 kA, Ics= 100% Icu | Numbers 2.00 | — | 7,494.65 | 14,989.3 |
| 26 | Copper bus bar 100 amps made of electrolytic grade copper consisting of 4 bars ( 3 Ph and Neutral ) ( Bus bar should have insulation cover) | Set 2.00 | — | 820.65 | 1,641.3 |
| 27 | Supply and Erection of protective screen as per instruction of site enggineer | Sqm 120.00 | — | 6,683.57 | 8,02,028.4 |
| 28 | Supply, installation, testing & commissioning of Step down Distribution Transformer 250 KVA, 11/0.433 KV, 3 phase, 50 Hz, outdoor type, copper wound, Delta/star, Tap changer having range +5% to -5% in steps of 2.5% each with all fittings and accessories as per IS:2026. | Numbers 2.00 | — | 3,72,367.81 | 7,44,735.62 |
| 29 | Supply & execution of transformer bed by CC foundation (1:3:6) of size (3.0 m x 2.0 m x 2.0 m) including plastering by morter ratio (1:4) including digging of soil/surface as per instruction of Engineer incharge at site. (For installation of transformer) | cum 36.00 | — | 4,082.35 | 1,46,964.6 |
| 30 | Supply, erection, testing & commissioning of 11 kV , 200 amps, 3 Pole vertical type Gang Operated Air Break switch TILTING type complete with square shaft, operating pipe, handle, guide clamp etc ( 3 no in a set) as per instruction of Engineer incharge at site. | Numbers 4.00 | — | 10,317.4 | 41,269.6 |
| 31 | Supply, erection, testing & commissioning of Distribution lightning arrestors, 9 kV / 5KA with all accessories as per instruction of Engineer incharge at site. Lighting arrestor must conform to IEC 99-4/1991 (3 no in a set) | Numbers 2.00 | — | 7,873.71 | 15,747.42 |
| 32 | "Supply of swaged type GI tubular pole 11 mt long conforms to IS - 2713/1980 with following technical specification and complete with base plate and cap: - a) Length of section : - Bottom - 5.60 mt, Middle - 2.70 mt, Top - 2.70 mt b) Outside diameter and thickness of section : - Bottom - 165.1 x 4.85 mm, Middle - 139.7 x 4.50 mm , Top - 114.3 x 3.65 mm" | Numbers 20.00 | — | 23,538.23 | 4,70,764.6 |
| 33 | Supply of "Base plate and GI cap" for above tubular pole as per instruction of Engineer incharge at site. | Numbers 20.00 | — | 1,707.13 | 34,142.6 |
| 34 | Erection of rail/tubular pole to 1/5 th of its height with CC foundation from base block (30 cm x 30 cm x 15 cm) including digging & refilling of earth to a height of 30 cm above ground level as per drawing no.CEE/OH@47'40@FGA) in ratio 1:3:6 by cement sand & Chips 19 mm & down including excavation of earth (Rail pole will be supplied by Railway) | Numbers 20.00 | — | 1,575.77 | 31,515.4 |
| 35 | Supply & fixing of MS channel bracket (75 x 40 x 40 x 6) mm to be clamped with the pole by clamp made of 50x5 mm MS flat and 50x 16 mm MS nut,bolt & washer including drilling of holes | Metre 200.00 | — | 294.59 | 58,918 |
| 36 | Supply & fixing of MS angle bracket (50 x 50 x 6) mm to be clamped with the pole by clamp made of 50x5 mm MS flat and 50x 16 mm MS nut,bolt | Metre 300.00 | — | 251.2 | 75,360 |
| 37 | Laying, commissioning & testing of HT/LT XLPE/PVC cable of different sizes partly along the pole/wall and partly through ground in cable trench by excavation of ground below 1.5 mt from ground level with suitable fixing arrangement. | Metre 800.00 | — | 49.96 | 39,968 |
| 38 | Excavation of cable trench (0.3 x 1.5) mtr below ground level for laying of cable & refilling the soil after digging the earth as per instruction of Engineer incharge at site. Cable should be laid on bedding of height 75 mm sand at the bottom of trench, and covering it with additional sand of height 75 mm and thereafter protecing it by mean of bricks before refilling the soil as per IS 1255. | Metre 500.00 | — | 134.85 | 67,425 |
| 39 | Supply & handover of HT 11 kV (E) cable termination Kit out door, heat shrinkable type for 3 core, 120-185 sq mm XLPE insulated PVC armoured cable complete with jointing materials as per instruction of Engineer incharge at site. | Numbers 6.00 | — | 18,026.08 | 1,08,156.48 |
| 40 | Supply & erection of FRP fencing of S/stn (Aprox fencing size- 20 Ft x 20 Ft) with corrosion resistant, acid proof, fire retardant, non-magnetic, high quality fiber glass FRP with gate and locking arrangent. | Square 400.87 Foot | — | 479.64 | 1,92,272 |
| 41 | Supply , laying , commissioning & testing of CI Pipe 200 mm dia Class LA type (IS 1536-2001) to be laid partly along the pole and partly through ground under railway track/road in cable trench for protection of cable with suitable fixing arrangement by MS clamp, nut,bolt,washer etc.as per instruction of Engineer incharge at site. | Metre 200.00 | — | 1,468.61 | 2,93,722 |
| 42 | Horizontal machine boring of 300 mm dia hole across track/Road/High drain etc. at a depth of 1.0 mtr below of ground level with suitable boring instruments & neessary arrangement and as per technical procedure. | Metre 250.00 | — | 2,323.11 | 5,80,777.5 |
| 43 | Dismantling and shifting of existing poles, light fitting and other electrical accessories .as per instruction of Engineer incharge at site. | Job 1.00 | — | 43,848 | 43,848 |
| 44 | Supply, laying, installation and commissioning of indoor Cable tray 105/300 MM with all Supporting & Jointing Accessories as per instruction of Engineer Incharge at Site. | Metre 1600.00 | — | 1,526 | 24,41,600 |
| 45 | Supply, fixing, testing & Commissioning of 11 kV composite Pin insulator polymer type with all accessories as per instruction of Engineer incharge at site. Insulator must conform to IEC - 61109 with upto date ammendments. | Numbers 30.00 | — | 212.3 | 6,369 |
| Schedule total | ₹1,69,64,081.76 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCCandAmendment_10.pdf
ATTACHMENT
RITES-RDSO.pdf
ATTACHMENT
ier1956.pdf
ATTACHMENT
NC-5GEN.pdf
ATTACHMENT
NC-05GEN_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .