Miscellaneous carpentry works at HWPM colony for the year 2024-2025.

Amount

Removing of old dry and damaged glass putty, then providing and applying fresh glass putty to fix the glass in proper position including glazing clips at all levels including scaffolding wherever necessary etc., complete as per specifications and as directed by the Engineer.

Supplying and fixing of 16mm thick cement bonded board for door shutters of size 750mm x 2100mm and alround "U" lipping 25 x 18 x 25mm with 0.60 mm thick pre-painted cold rolled steel sections or PVC and fixing with 300mm MS powder coated "T" hinges to the existing frame with welding, including fixing of standard hardwares (powder coated 250mm x 16mm aldrop - 1No, 250mm x 20mm x 6mm MS Oxidied latch-1No, 125mm powder coated MS handle-2Nos) and painting with two coats of exterior emulsion paint like TRUMP or equivalent paint over a coat of cement primer and applying one or more coat of synthetic enamel paint on hinges and MS frame after welding, including removal of old hinges, shutters & fittings and handing over of old/ damaged shutter & fittings to the sectional stores, disposing of debris generated in the dumping yard etc., complete as per drawings, specifications and as directed by the Engineer. Notes: 1) The size of the Door may vary slightly from door to door as per the site condition. Exact measurements are to be taken at site before fabrication. 2) Rate shall be Inclusive of all labour material,Transport etc. complete.

Providing and fixing in position of 20mm thick cement bonded particle board (bison board) in the cupboard shelves as per the existing patterns and arrangement as directed by the Engineer including cutting to required size with power cutter, supply and fixing necessary nuts and bolts, making the edges smooth, making holes to board for fixing nuts & bolts, applying two or more coats of exterior emulsion paint like TRUMP or equivalent over a coat of cement primer on both sides including removing of old damaged cupboard planks and handing over the useful material at sectional stores and disposing the waste material to the dumping yard etc. complete as per drawings, specifications and as directed by the Engineer

Providing and fixing in position Fly proof Stainless steel grade 304, wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50mm to the existing kitchen windows and other areas in place of damaged fly proof mesh by using existing or new beeding/ existing steel frame including nuts and bolts, removing of old damaged mesh and hand over to sectional stores etc. all complete as per specification and as directed by the Engineer.

Supplying and fixing Float glass panes of 4mm thick of weight not less than 10kg/ Sqm with locking clips and glass putty/ wooden fillets wherever required, including removing of old damaged glass and putty and disposing of waste to the dumping yard etc. all complete as per specifications and as directed by the Engineer.

Supplying and fixing Float glass panes of 5mm thick of weight not less than 12.50 kg/ Sqm with locking clips and glass putty/ wooden fillets wherever required, including removing of old damaged glass and putty and disposing of waste to the dumping yard etc. all complete as per specifications and as directed by the Engineer.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia (heavy type) including necessary screws complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing in position 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade-I, IS : 3087 marked including top cover of 6 mm thick commercial ply wood conforming to IS : 303 BWR grade, nickle plated MS pipe of 20 mm dia (heavy duty) curtain rod with nickle plated brackets,including fixing with 25 x 3 mm M.S. flat 10 Cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner sides of pelmet and rowl plugs 75 mm long etc. all complete finished with two coats synthetic enemal paint of approved quality over a coat of primer etc. complete as per drawings, specifications and as directed by the Engineer.

Providing and fixing 25 mm thick black board shutter for cupboards double leaf including the cost of lipping with 2nd class teakwood batten 25mm depth on all edges of shutter including providing and fixing powder coated MS hinges with necessary screws, cutting rebate in the shutter including cost of approved heavy duty MS fittings (Anodic coating tower bolt not less than grade AC 10 as per IS : 1868 of size100mm x 10mm -1No, Chromium plated Brass 50mm knob -2 No's, special quality bright finished brass Cup board lock 40mm - 1 No) and painting with two or more coats of synthetic enamel paint over a coat of wood primer etc., complete all and including removal of old shutters, recory of usefull fittings and fixtures and handing over the same to sectional stores and disposing the waste material to the dumping yard etc., complete as per specification and as directed by Engineer.

Providing wood work in Frames of doors, fixed in position with well seasoned/ treated best quality 2nd class Teak wood including application of two coats of bituminous primer on all surfaces of wood coming in contact with masonry or concrete, painting with two coats of synthetic enamel paint of approved make and shade over a coat of wood primer including removing the damaged door frame/ shutter and handing over to the sectional stores, fixing the new frame with hold fasts and embedding with concrete of 1:3:6 of 75mm thick etc., complete including removal of old frame and handing over of useful material to the sectional stores and disposal of the waste to the dumping yard etc., as per specifications and as directed by the Engineer.

Providing and fixing 30 mm thick ISI marked flush door shutters of size 900mm X 2100mm conforming to IS : 2202 (Part I) of approved make non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including fixing with ISI marked Stainless Steel butt hinges with necessary screws, two coats of synthetic enamel paint of approved shade over a coat of wood primer and fixing of MS Aldrop of size 250mm x 16mm - 1No, MS latch 250mm x 20mm x 6mm - 2 Nos, MS door handles of 125mm size - 1 No, Tower bolt of size 200mm x 10mm - 1No, Brass door stopper of good quality -1No etc., complete all as per specifications and as directed by the Engineer in Charge. (Note: Rate is inclusive of removal of old/ damaged door and handing over to the sectional stores & fixing of existing Night latch & judes eye to the new door and disposal of waste generated to the dumping yardetc.,)

Providing and fixing Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) work for doors, windows and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, including providing & fixing hinges/ pivots and making provision for fixing of fittings wherever required, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws etc., all complete as per architectural drawings and the directions of Engineer in charge. (Glazing/ panelling to be paid for separately) Note : Repair works shall be guaranteed for one year for smooth operation.

Removing and re-fixing of aluminium sectons for doors, windows and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections (using available Aluminium sections retrieved from dismantling), including providing & fixing hinges/ pivots and making provision for fixing of fittings wherever required, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws including dismantling and reusing the same, handing over of the excess/serviceable material to the departmental store etc., all complete as per architectural drawings and the directions of Engineer in Charge. (Glazing/ panelling to be paid for separately under relevant items) Note : Repair works shall be guaranteed for one year for smooth operation.

Providing and fixing 12 mm thick exterior grade quality prelaminated particle board with decorative lamination on one side and balancing lamination on other side, flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass/ stainless steel screws etc., all complete as per specification and as directed by the Engineer in Charge.

Supplying and stacking of glass/ metal sash putty of approved brand with ISI grade etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing 600x450 mm beveled edge mirror (outer dimensions) mirror of superior glass (of approved quality) of approved make and shade with 6 mm thick hard board backing and C.P. brass caped screws & washers etc., complete all as per specifications, drawings and as directed by the Engineer in Charge.

Providing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. all as per specifications, drawings and as directed by the Engineer in Charge.

Providing hanging type 150 mm size brass floor door stopper weighing not less than 0.357kg with rubber bush at the bottom side of stopper, suitable for use with door shutters of 30, 35, 40 and 45 mm thickness. etc., all complete as per the manufacturer specifications and as directed by the Engineer in Charge.

Providing and fixing factory made 30 mm thick solid non Decorative finish door shutter made of solid WPC (Wood Polymer Composite) profile.750mm x 2100mm (size may vary as per the site condition) of brands like( GREENPLY/ HARDYPLAST / CENTURY PLY) or any other approved make . fixing with 300mm stainless steel"T" hinges (3 Nos) to the existing frame with welding, including fixing of standard hardwares & fixing of aluminium grade AC 10 as per IS : 1868 Aldrop of size 250mm x 16mm - 1No, latch 250mm x 20mm x 6mm - 1 No and door handles of 125mm size - 2 No's, Aliminium Tower bolt of size 200mm x 10mm - 1No etc., complete all as per manufacturer's specifications and direction of Engineer-in-charge.

Providing 600 mm long PTMT towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms., complete with brackets including CP brass screws with concealed fitting arrangement of approved quality and colour etc., all complete as per specification and as directed by the Engineer in Charge.

Supplying Hard drawn steel wire fabric 75 x 25 mm / 50 x 50 mm mesh of weight not less than 7.75 kg/sqm etc., all complete as per specification and as directed by the Engineer in Charge.

A RAMULU CONTRACTORS (BID ID -3145432)