PMURKILSGD - Rehabilitation of Athikkayam Kadumeenchira Road in Naranamoozhy GP in Pathanamthitta District (Balance Work - Rearranged after termination) (Retender)

Roads & Structures

2.5.2.B : Dismantling of Structures<br> Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specification Clause 202.<br> (II) By Mechanical Means <br>(B) Reinforced Cement Concrete

2.13.A : Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202. (A)Upto 600 mm dia Hume pipe

2.7.B : Dismantling Stone Masonry as per Technical Specification Clause 202. Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of stone masonry, including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 m as per Technical Specification Clause 202.(B)Rubble Stone Masonry in Cement Mortar

od1434822/2021_2022 : Providing, laying and spreading material on a prepared subgrade adding the designed quantity of cement to the spread material, mixing in place with rotavator, grading with motor grader and compactin gwith roller to acheive the desired unconfined compressive strength and to form a layer of subbase-Cement treated crushed rock or combination as per clause 403.2 and table 400.4

od1473557/2021_2022 : Construction of un-reinforced,plain cement concrete pavement ,thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M 30 (grade),coarse and fine aggregates conforming to IS 383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork(steel channel, laying and fixing of 125 micron thick polythene film, wedges,steel plates including levelling the formwork as per drawing),spreading the concrete with showels,rakes,compacted using&lt;br&gt;needle,screed, and plate vibrators and finished in continuous operation including provision of contraction and expansion ,construction joints,applying debonding strips, primer, sealant, and construction joints, admixtures as approved,curing of concrete slabs for 14 days,using curing compound(where specified) and water finishing to lines and grade as per drawing and Technical Specifications clause 1501. Short panelled of size 0.75m x 0.75m (Modified item 6.4). Extra labour and machinery added for close joint cutting

3.14 : Construction of Subgrade and Earthen Shoulders<br> Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1.

11.1.1.2 : Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. I. Ordinary soil (ii)3 m to 6 m depth

75.7.1 : DRY RUBBLE MASONRY _ Random rubble masonry with hard stone, including Through/Bond stone in foundation and superstructure including packing to compactness to lines and levels, cost and conveyance of all materials labour charges etc. complete as per approved drawing and relevant technical specifications.

od1435238/2021_2022 : DRY RUBBLE MASONRY _ Random rubble masonry with hard stone, including Through/Bond stone in foundation and superstructure including packing to compactness to lines and levels, cost and conveyance of all materials labour charges etc. complete as per approved drawing and relevant technical specifications-using departmental rubble.

11.6.3.2 : Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203.III. Random Rubble Masonry (ii)In cement mortar 1:4

od1435299/2021_2022 : Supplying and providing MS dowel bars of size 16mm dia of 2m long (1m in rock and 1m in concrete) including drilling holes of 20mm dia to a depth of 1m in rock and filling the gap with cement grout etc complete

od1435300/2021_2022 : Bailing out water using 5HP pump-bailing out water with 5 HP engine and pump set including conveyance to site and erection, cost of fuel, lubrication oil and other stores, pay to staff etc complete

od1435303/2021_2022 : Putting up Ring Bund (Type II) with earth filled gunny bags of top width 1m bottom width, 2m height 2m side and filling in between with earth to form ring bund and maintaining the same leak proof till completion of the work and clearing the site by dismantling the bund after completion of the work etc complete

11.4.5 : Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203V. R.C.C. grade M 25

11.7 : Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

12.5.4 : Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 For height upto 5 mIV.R.C.C. grade M 25

12.6 : Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

13.1.2 : Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5R.C.C M 25

13.1.1.3 : Providing and laying reinforced cement concrete in super structure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 . 1. R.C.C grade M20 (iii) For desaign mix RCC M20

13.2 : Supplying, fitting and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002,1010 and 1202

13.11 : P.C.C.M 15 ordinary grade (1:2:5:5) leveliing course below approach slab complete as per drawing and technical specifications Clauses 800 and 1211. Nominal mix (1:2:5:5)

14.8 : Providing and laying of dry rubble flooring complete as per drawings and technical specifications Clause 1303.3

12.9 : Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

12.11 : Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8

75.8.1.1 : Providing plain/reinforced concrete(1 cement:2 fine aggregate: 4 course aggregate) for substructure as per drawings and technical specifications Clause 802, 803, 1202 & 1203 as required including compaction, finishing and tamping etc .complete. Max. size of course aggregate not exceeding 25mm , mixed in concrete mixer etc complete as per specification (i) Nominal mix (1:2:4)

9.7 : Laying Cement Concrete Pipe NP3 (burried conduits) on first class bedding of granular material including fixing collar with cement sand mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonary work in head wall and parapets

od1435319/2021_2022 : Providing and erecting a &quot;W&quot; metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811.3

10.2.A.1.2 : Traffic Signs<br>A. Retro-reflectorised Traffic Signs <br> 1 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 <br> 2 600 mm Equilateral Triangle

10.2.A.1.3 : Traffic Signs<br>A. Retro-reflectorised Traffic Signs<br>1 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 <br> 3 600 mm Circular

10.10.2 : Kilometre Stone Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 2Ordinary Kilometer Stone (Precast)

10.10.3 : Kilometre Stone Kilometre StoneReinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703iii)200 m stone (precast)

10.4.A.1 : Direction and Place Identification signs with size more than 0.9 sqm size board <br> A. Retro-reflectorised Traffic Signs <br> 1 Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

od1435316/2021_2022 : Providing and fixing guard post of size 200mmX200mmX1400mm long 800mm above GL and 600mm below GL cast in M20 grade concrete reinforced with 4 nos of 8mm bars and 6mm dia stirrups @ 100mm c/c firmly fixed in foundation of size 0.5mx0.5mx0.7m in M15 grade concrete below GL including painting 2 coats of synthetic enamel paint in alternate white and black bands of 20cm width

od1435317/2021_2022 : Providing and erecting retro-reflectorised Object Hazard Marker 300mm x&lt;br&gt;900mm&lt;br&gt;Providing and erecting retro-reflectorised Object Hazard Marker sign with 07&lt;br&gt;years warranty, manufactured as per IRC 67 USING Type IV ASTM D 4956-09&lt;br&gt;micro prismatic retro reflective sheeting fixed over aluminium sheetig, 2 mm thick&lt;br&gt;/ aluminium composit material sheeting 4 mm thick with suitable back support&lt;br&gt;frame and supported on a mild steel angle iron post 75mmx75mmx6mm, firmly&lt;br&gt;fixed 30cm above ground level by means of properly designed foundation with M&lt;br&gt;15 grade cement concrete 30cmx30x45cm, 45cm below ground level including&lt;br&gt;painting all non-reflective faces with epoxy paint 2 coats over epoxy primer as&lt;br&gt;per approved drawing and clause 801.&lt;br&gt;300 mm x 900 mm(Data from MORTH 55.10.1)

Please Enable Macros to View BoQ information