Construction for Development and Beautification of Historic Shiv Temple at Paudiwala near Nahan, Sirmaur (HP)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains in all heights and depths in all kinds of soil, including saturated soil comprising of pick work,jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohabited) and their intermediate classification of soil including dewatering whereever required,settling out to required lines,levels as shown on the drawing and directed by the Engineer in charge at site according to the HP.PWD specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (to be arranged by the contractor) including payment of prescribed dumping charges of M.C. if levilled any to the satisfaction of the Engineer in charge through all modes of transporation including head load animal load or mechanical means alongwith its levelling, fine dressing and with all kinds of labour, mechineries, tools, equipment and safety measures and incidental necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transporation and used/removed as per the satisfaction of the Engineer in charge. any loss to the public and private properity during the course of execution and disposal of servicable and unservicable materials shall be the absolute responsiblity of the contractor and shall have to be duly compensated by him in all respects including all incidential charges and as directed by the Engineer in Charge:- All kinds of soil.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete as per HP.PWD., specification 1990 volume-I ( one ) including carriage of all labour equipments and materials to various location through all leads, lifts and other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:5:10 (one Cement : five coarse sand : ten graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Making plinth protection 50 mm ( fifty milimetre ) thick of cement concrete 1 : 3 : 6 ( One cement : three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) over 75 mm ( seventy five milimetre ) thick bed of dry brick ballast 40 mm ( forty milimetre ) nominal size, well rammed & consolidated & grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position specified grade of reinforced cement concrete of mechanically mixed , vibrated & curing complete excluding the cost of centering, shuttering, finishing & reinforcement - All work up to plinth level and all floor level in 1:1.5 : 3 (One Cement : One & half coarse sand : five graded stone aggregate 20mm (twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in walls (any thickness), mechanically mixed, vibrated and curing complete including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level , excluding cost of centering, shuttering, finishing and reinforcement in 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all level mechanically mixed, vibrated and curing complete, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing form work with steel plates 3.15mm ( three point fifteen millimeter ) thick welded with angle iron in frame 30X 30X5mm ( thirty X thirty X five millimeter ) so as to give a fair finish including centering ,shuttering, strutting and propping etc. with wooden battens and ballies , height of propping and centering below supporting floor to ceiling not exceeding 4.00 meters ( four meters ) and removal of the same for insitu- reinfoced concrete and plain concrete work including all leads and lifts of materials or as per the directions of Engineer in Charge.

Foundations, footings, bases of columns, etc. for mass concrete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Suspended floors, roofs, landings, balconies and access platform including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Columns, Pillars, Piers, Abutments, Posts and Struts Circular including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Stairs, (excluding landings) except spiral stair cases including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Edges of slabs and breaks in floors and walls Under 20cm ( twenty centimeter ) wide including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and placing steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding wire all complete upto floor all level. Thermo-Mechanically Treated bars of grade Fe-500 D or more including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Rat trap brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Rat trap brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1 :4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes : Cement mortar 1 : 4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 18 mm ( eighteen milimetre ) thick gang saw cut, mirror polished, premoulded & prepolished, machine cut for kitchen plateforms,vanity counters, window sills, facias & similar locations of required size, approved shade, colour & texture laid over 20 mm ( twenty milimetre ) thick base cement mortar 1 : 4 ( One cement : four coarse sand ), joints treated withwhite cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, coulding & polishing to edges to give high glass finish etc. complete at all level Granite of any colour, shade & all area of slab including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing first quality Ceramic glazed wall tiles conforming to IS : 15622 ( thickness to be specified by the manufacture ), of approved make, in all colours, shades, except burgundy, bottle green, black of any size as approved by the Engineer-in-Charge in Skirting, risers of steps & dado over 12 mm ( twenty millimeter ) thick bed of cement mortar 1:3 (one Cement : three Coarse sand) and jointed with grey cement slurry @ 3.3kg/ sq.m (three point three zero kilograme per square meter ) including pointing in white cement mixed with pigment of matching shade complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing panelling or panelling & glazing in panelled or panelled & glazed shutters for doors, windows & clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ), panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimetre to fourty milimetre ) thick Particle board 12 mm thick pre-laminated particle board with decorative lamination on both side, grade 1, Type-II, IS: 12823 marked, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing panelling or panelling & glazing in panelled or panelled & glazed shutters for doors, windows & clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ), panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimetre to fourty milimetre ) thick Particle board 12 mm thick pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, grade 1,Type-II, IS: 12823 marked, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing panelling or panelling & glazing in panelled or panelled & glazed shutters for doors, windows & clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ), panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimetre to fourty milimetre ) thick, 5.5 mm ( Five point five milimetre ) thick glass pans(weight not less than 12.50 Kg ( Twelve point five zero kilogramme ) per square metre),, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PGI/PVC Rigis foam sheet 1 mm ( One milimetre ) thick on existing doors shutters ( bath room & W.C. doos ) using synthetic rubber based adhesive, including alllead, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing wooden moulded beading to door & windows frames with iron screws, plugs & priming coat on unexposed surface etc. complete second class teak wood 50 x 12 mm ( fifty into twelve milimetre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 300 x 16 mm ( three hundred into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 200 x 10 mm ( two hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 x 10 mm ( one hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm ( one hundred twentyfive milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm ( one hundred twenty five milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Single rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Twin rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand ) logo with ISI, IS:3564, embossed on the body, door weight upto 35Kg ( Thirty five kilogram ) door with upto 700mm ( seven hundred milimetre ) with necessary accessories & screws etc. complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing grab bars 600mm x 40mm ( Six hundred milimetre into forty milimetre ) in handicapped toilets two number each chromium plated 40mm ( forty milimetre ) dia steel pipe at 78cm ( Seventy eight centimetre ) height with mild steel plates as per detail at the position of the seat & wash basin, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses & framed work,including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer all complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel round holding down bolts with nuts & washers plates complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer using structural steel etc. as required in grating, frames, guard bars, ladders, railing, brackets, gates & similar work including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing & similar works, including applying priming coat of approved steel primer mild steel tube/pipe, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Mirror polished Kotah stone slab flooring over 20 mm ( twenty milimetre ) ( average ) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of cement mortar 1 : 4 ( one cement : four coarse sand ) 19 mm ( ninteen milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Mirror polished Kotah stone slab 20 mm ( twenty milimetre ) thick in risers of steps, skirting, dado & pillars laid on 12 mm ( twelve milimetre ) ( average ) thick cement mortar 1 : 3 ( One cement : three coarse sand ) & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Cement concrete flooring 1 : 2 : 4 ( One cement : two coarse sand : four graded stone aggregate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm ( forty milimetre ) thick with 20mm ( twenty milimetre ) nominal size ) stone aggregate including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Cement plaster skirting upto 30 cm ( thirty centimetre ) height with cement mortar 1 : 3 ( One cement : three coarse sand ) finished with a floating coat of neat cement 18 mm ( eighteen milimetre ) thick including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing glass strips in joints of terrazo/ cement concrete floors 40 mm ( forty milimetre ) wide & 4 mm ( four milimetre ) thick including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & laying vitrified double charge floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % & conforming to IS 15622, of approved make, in all colours and shades, laid on 20 mm ( twenty milimetre ) thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3 Kilogram per square metres including grouting the joint with white cement & matching pigments etc. complete size of tile 300 x 300 mm, ( Three hundred into three hundred milimetre ) including all leads, lifts, & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

40 mm ( forty milimetre ) thick fine dressed stone flooring over 20 mm ( Twenty milimetre ) ( average ) thick base of cement mortar 1:5 ( One cement : five coarse sand ), including pointing with cement mortar 1 : 2 ( One cement : two stone dust ) with an admixture of pigment to match the shade of stone , Red sand stone, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 110mm ( One hundred ten millimeter ) diameter metre.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Bend 87.5° 110mm ( eighty seven point five degree one hundred ten millimeter ) bend.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Shoe ( Plain )110mm ( One hundred ten millimeter ) shoe.

Providing & fixing mild steel holder bat clamps of approved design to cast iron or S.C.I. rain water pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1 : 2 : 4 mix ( One cement : two coarse sand : four graded stone aggregate 20 mm nominal size ) & cost of cutting holes & making good the wall etc. 110 mm ( One hundred ten milmetre ) diameter PVC pipe including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing 0.60 mm ( sixty milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP ) organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coting to back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm ( six milimetre ) dia metre with prepainted limpet & rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing ridge or hips 0.60 cm ( sixty centimetre ) over all with thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coting plus back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm ( six milimetre ) dia and prepainted G.I. limpet & rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing valley 60cm overall 0.60 mm ( sixty milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia with prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing flushing 38 cm ( thirty eight milimetre ) overall 0.45 mm ( zero point four five milimetre ) thick prepainted steel sheet Tata Duro Shine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm ( six milimetre ) dia with prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge , including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing 30 cm ( thirty centimetre ) wide 120 cm ( one hundred twenty centimetre ) overall Box type prepainted Zinc coated sheet gutter with iron bracket 40 x 3 mm ( forty into three milimetre ) size, bolts & nuts and washers etc. including making necessary connections with rain water pipes complete as per design. 0.45 mm ( forty five milimetre ) thick, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing mild steel B.P. sheet 1.66 mm to 2 mm ( One point six six milimetre to two milimetre ) thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing & welding to steel roof members & applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge ( Base member of steel work shall be measured & paid for separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:6 (one cement: six fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:4 (one cement: four fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

6 mm ( Six milimetre ) cement plaster of mix 1 : 3 ( One cement : three fine sand ), including all leads, lifts & as directed by the Engineer in Charge.

Providing & applying white cement based putty of average thickness 1 mm ( One milimetre ), of approved brand & manufatureer, over the plastered wall surface to prepare the surface even & smooth complete, including all leads, ,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade new work ( two or more coats ) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing walls with Acrylic smooth exterior paint with of required shade new work ( two or more coat ) applied @ 1.67 litre/10 Sqmt ( one point six seven litre per ten square metres ) over & including priming coat of exterior primer applied @ 2.20 Kg /10 Sqmt ( at the rate two point two zero kilograme per ten square metre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing in position collapsible steel shutters with vertical channels 20x10x2mm ( twenty into ten into two milimetre ) & braced with flat iron diagonals 20 x 5 mm ( Twenty into five milimetre ) size, with top & bottom rail of T-iron 40x40x6mm, ( forty into forty into six milimetre ), with 40 mm ( forty milimetre ) dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS : 733 & IS : 1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, stright, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per Architectural drawings & the direction of Engineer-in-Charge ( Glazing, panelling & dash fasteners to be paid for separately ) For fixed portion, Powder coatd aluminium ( minimum thickness of powder coating 50 micron ),including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded built up standard tubular sections/ appropriate Z sections & other sections of approved make conforming to IS : 733 & IS : 1285, fixing with dash fasteners of required dia & size, including necessary filling up the gaps at junctions, i.e. at top, bottom & sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, stright, mitred & jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per Architectural drawings & the direction of Engineer-in-Charge ( Glazing, panelling & dash fasteners to be paid for separately ) For For shutters of doors, windows & ventilators including providing & fixing hinges/Pivots & making provision for fixing of fittings whereever required ,including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm ( Two hundred milimetre ) centre to centre, including cutting the grill to proper opening size for fixing & operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. (Only weight of grill to be measured for payment), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing panelling or panelling and glazing in panelled or panelled & glazed shutters for doors, windows and clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm ( Twenty five milimetre to forty milimetre ) thick , Fly proof stainless steel grade 304 wire gauge with 0.5 mm ( Zero point five milimetre ) dia. wire and 1.4 mm ( One point four milimetre ) wide aperture with matching beading, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm ( one hundred millimeter ) sand cast Iron P or S trap, 10 litre ( ten litre ) low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge: White Vitreous china Orissa pattern W.C. pan of size 580mm x 440mm ( five hundred eighty millimetre X four hundred forty millimeter ) with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10litre ( ten litre )low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- W.C. pan with ISI marked white solid plastic seat and lid.

Providing & fixing white Vitreous China flat back half stall urinal of size 630x420x390 mm with ( Six hundred thirty into four hundred twenty into three hundred ninety milimetre ) white PVC auotmatic flusing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with union & clamps ( all in C.P. brass ) with waste fitting as per IS : 2556, C.I. trap with out let grating & other couplings in C.P. brass, including painting of fittings & cutting & making good the walls & floors wherever required Range of two half stall Urinals with 5 litre P.V.C. automatic flushing cistern, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15mm ( fifteen millimeter ) C.P. brass pillar taps, 32mm ( thirty two millimeter ) C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete, White Vitreous China wash basin size 550mm x 400mm ( Five hundred fifty millimeter X four hundred millimeter ) with single 15mm ( fifteen millimeter ) C.P. Brass pillar tap, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge..

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing stainless steel Kitchen sink No. KCG 1012 ( Size 810 x 450 mm ) ( Size eight hundred ten into four hundred fifty milimetre ) with C.I. brackets & stainless steel plug 40 mm ( forty milimetre ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink with bowl depth 200 mm, including all leads,lifts,carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing stainless steel A ISI 304 ( 18/8 ) kitchen sink as per IS: 13983 with C.I. brackets & and stainless steel plug 40 mm ( forty milimetre ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink with drain board 460 x 385mm ( four hundred sixty into three hundred eighty five milimetre ) bowl depth 200 mm ( two hundred milimetre ) , including all leads, lifts, & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing and fixing 600mm x 450mm ( Six hundred millimeter into four hundred fifty millimeter ) beveled edge mirror of superior glass (of approved quality) complete with 6mm ( six milimetre ) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing 600mm x 120mm x 5mm ( Six hundred millimeter into one hundred twenty millimeter into five millimeter ) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm ( forty millimeter ) long screws, rawl plugs etc., complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass toilet paper holder complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing PTMT liquid soap container 109mm ( one hundred nine millimeter ) wide, 125mm( one hundred twenty five millimeter ) high and 112mm( one hundred twelve millimeter ) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 125gms ( one hundred twenty five grams ) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providuing & fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangement of approved quality & colour, 450 mm ( Four hundred fifty milimetre ) long towel rail with total length of 495 mm, 78 mm ( Four hundred ninety five milimeter, seventy eight milimetre ) wide & effective height of 88 mm ( eighty eight milimetre ) , weighting not less than 170 ( One hundred seventy ) grams including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 1216 (16 mm ( sixteen millimeter ) OD) pipe.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:-1620 (20mm ( twenty millimeter ) OD) pipe.

Providing and fixing G.I. pipes complete with G.I. fittings & Clamps including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work:-15mm ( fifteen millimeter ) dia nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work :- 20mm ( twenty millimetre ) dia.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.External work:-15mm ( fifteen millimeter ) dia nominal bore.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass stop cock ( Concealed ) of standard design & of approved make conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass angle valve for basin mixer & geyser point of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing & fixing C.P. brass extension nipple ( size 15 mm x 50 mm ( fifteen milimetre into fifty milimetre ) of approved make & quality as per direction of Engineer-in-Charge including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20mm ( twenty millimeter ) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40mm ( forty millimeter ) nominal size), inside plastering 12mm ( twelve millimeter ) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm ( twenty millimeter ) nominal size) finished with a floating coat of neat cement complete as per standard design complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. : Inside size 90cm x 80cm and 45cm ( Ninety centimeter into eighty centimeter and forty five centimeter ) deep including C.I. cover with frame (medium duty) 455 x 610 mm ( Four hundred fifty five into Six hundred ten millimeter ) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram ) (weight of cover 23 kg ( twenty three kilogram ) and weight of frame 15 kg( fifteen kilogram ) With common burnt clay F.P.S. (non modular) bricks of class designation7.50.

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 150mm dia ( One hundred fifty milimetre ) including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 150 mm ( one hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 100 mm ( one hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three milimetre ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 150 mm ( One hundred fifty milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 100 mm ( One hundred milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC clamps ISI marked of approved design with steel screws & rawal plugs etc. complete 75 mm ( Seventy five milimetre ) dia including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete 150 mm x 110 mm ( One hundred fifty milimetre into one hundred ten milimetre ) dia, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete 110 mm x 75 mm ( One hundred ten milimetre into seventy five milimetre ) dia, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting & making good the wall & floors etc. complete 110 mm x 90 mm ( One hundred ten milimetre into ninety milimetre ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting & making good the wall & floors etc. complete 110 mm x 75 mm ( One hundred ten milimetre into seventy five milimetre ), including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing 15 mm ( fifteen milimetre ) mixer for kitchen sink with top/ bottom swining spouts, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing 8 mm ( eight milimetre ) dia C.P./S.S. Jet with flexible tube upto 1.00 ( One ) metre long with S.S.triangular plate to Eureopean type W.C. of quality & make as approved by Engineer-in-Charge, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) square shape 450 mm ( four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) rectangular shape 600 x 450 mm ( six hundred into four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Supplying & filling brick bats in dispension trenches ( Brick aggregate ( Single size ) 50 mm ( Fifty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 75 mm ( Seventy five millimeter ) diameter metre.

Providing and fixing on wall face PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm (ten millimeter) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Bend 87.5° 75 mm (eighty seven point five degree Seventy five millimeter) bend.

Pratap Singh

Mohan Singh

THAKUR CONSTRUCTIONS

M/S SHANTI SARUP DINESH CHAND