Colour Work of Various Existing Buildings of Hydraulic Department in New East (Sarthana) Zone, Surat Municipal Corporation, Surat.

1 Distempering two coats with oil bound washable distemper of

approved brand & manufacture & of required shade on wall surface

to give an even shade over and & including a priming coat of alkali

resistance primer of approved brand after throughly brushing the

surface to give an even shade after throughly brushing the surface

free from mortar droppings and other foreign matter and also

including preparing the surface even and smooth.

(A) Wall 12000.00 72.23 S.M.

(B) Ceiling 6000.00 80.35 S.M.

2 Painting two coats (excluding priming coat) on previously painted

wood & wood based surface with enamel paint to give an even

shade & surface incl. cleaning of all dirt, dust & other foreign

3 Painting one coat (excluding priming coat) on Previously Painted

steel and other metal surface with synthetic enemal paint, burshing

to give an even shade including cleaning the surface of all dirt, dust

and other foreign matters.

For every subsequent coat Extra over item no.above 10000.00 38.18 S.M.

4 Providing & applying two coats of weather shield max paint (3

coats may be required in case of darker colours.)of ICI Dulux or

Apex Ultima of Asian Paint including applying exterior acrylic

primer coat as per manufacturers specification and directions in

shade and colour approved by architects, on exterior surfaces of the

building including scaffolding, preparing the surface, watering,

curing etc. complete and as directed by the architects and

manufacturers.

Surface Preparation :

surface is thoroughly clean, dry and free from all loose dirt, chalk,

grease, fungi, algae and flaking paint. This can be achieved by 85000.00 82.00 S.M.

brushing with a wire/ stiff coir brush, followed by water jetting if

required. Fill up all minor cracks and defects with white cement

and sand mixture in the ratio 1:3. For application on previously

painted wall, previous coatings of paint must be thoroughly scraped

off and Clean the surface thoroughly using wire brushes.

Apply a liberal coat of exterior acrylic primer and allow it to dry for

4-5 hours. Application of putty is not recommended. Minimum 4-6

hours duration is required between each coat of weather shield max

5 White Washing with lime on wall surface to give an even shade &

surface incl. throughly brooming the surface to remove dirt, dust

mortar drops & losse scales of lime wash & other foreign matter

Two coats.

(A) Wall 2000.00 12.41 S.M.

(B) Ceiling 1000.00 13.53 S.M.

DESCRIPTION OF ITEM QUANTITY RATE UNIT AMOUNT

6 Apply two coats of putty and two coats of primer of approved brand

and manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from mortar

dropping and other matter and sand papered smooth

7 Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from mortar

droppings and other foreign matter and sand papered smooth.

8 Applying Priming coat over new steel and other metal surface after

over and including preparing the surface by throughly cleaning oil,

grease dirt and other foreign matter and scoured with brushed fine 100.00 35.00 S.M.

steel wool, scrapers and sand paper with ready mixed priming paint

brushing red lead.

9 Painting two coat (excluding priming coat) on new steel and other

metal surface with synthetic enemal paint, burshing to give an even

shade including cleaning the surface of all dirt, dust and other

foreign matters.

10 Applying Priming coat over new wood & wood surface after &

incl. preparing the surface by throughly cleaning oil grease dirt &

other foreign matter sand papering & knetting Really mixed paint

brushing priming for enamel.

11 Painting two coats (excluding priming coat) on New wood & wood

based surface with enamel paint to give an even shade & surface 100.03 88.45 S.M.

incl. cleaning of all dirt, dust & other foreign matter.

12 Painting two coats of enamel paint (Excluding priming coat) over

previously painted wall after removing entire surface with even

shade & surface after removing dirt, dust foreign matter etc.

comp.(M.R.)

13 Providing and applying Epoxy paint of approved make to concrete

surface for RCC ESR (inside the container) or any other structure

including clearing the surface by scrapping and air blowers to the

satisfaction of Engineer-in-charge necessary scaffolding etc. 100.00 97.00 S.M.

complete with all leads including necessary testing as per IS code.

For old surface - 2 coats

14 Writing letter or figures on any surface with black japan paint

(stops,comas, hyphens and the like not to be measured and paid for Per Letter

separately)(i) Block (Letters/Figures) (Per 10 Letter pet CM.HT) 100.00 3.18 Per

15 Writing letter or figures on any surface with black japan paint

Per Letter

(stops,comas, hyphens and the like not to be measured and paid for

separately) (ii) Indian (Letters/Figures)

16 Removing dry or oil bound distemper by a washing and scraping

and sand papering the wall surface smooth including necessary 100.00 11.30 S.M.

repairs to scratches complete.

DESCRIPTION OF ITEM QUANTITY RATE UNIT AMOUNT

17 Providing and supplying safety hanging net of appropriate capacity

/ dia. of rope and of suitable nylon quality which can withstand any

impact of human being etc. from the top of the tank and internal

and external periphery of ESR with necessary sufficient supporting

arrangement for. In short the arrangement should be such a way,

that the safety purpose shall be ensured with all respect during 2.00 89285.71 Job

construction period and the same can be taken back by contractor

after completion of the work duly concerned by Engineer in-

18 Taking photographs of work in progress and submit with each RA

bill. Photographs shall cover details of locations of the activity of

work in progress. The Contractor shall submit photographs with

Album in a set comprising 2 (two) copies (size of photograph is 4" 100.00 26.79 Set

x 6") and a soft copy of the same. Work shall be carried out as per

the instruction of the Engineer-in-charge

19 Cutting out cracks of wall or terrace to V section ,cleaningout,

grouting with cement and sand slurry 1:3 (1 cement : 3 sand ). at 0 65.23 RMT

any height

20 Crack Repairs:-Crack filling using fiber reinforced polymer modified

mortar after openning crack in "V" grove, Making Surface dust free,

with a bond coat of polymer as per the data sheet for crack

repairing cracks less than 8mm (market rate)

TOTAL AMOUNT (Rs.) :-

TOTAL AMOUNT (Rs.) :-

Hydraulic Engineer

Surat Municipal Corporatioin