Construction of Science Block at Govt. (PG) College, Dakpather Dehradun, Uttarakhand.

Amount

Section A DSR NO.- 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

DSR NO.- 2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

DSR NO.- 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

DSR NO.- 2.1.6+2.25+1.1.2 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

DSR NO.- 2.27 Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

DSR NO.- 2.10.1.2 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil, Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

DSR NO.- 2.35.3.1 Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the facesof the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II.(Plinth area of Building shall be measured for Payment).

DSR NO.- 4.1.8 P/L cement concrete - all works upto plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

DSR NO.- 4.11 Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

DSR NO.- 4.13 Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

DSR NO.- 4.1.3 P/L cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

DSR NO.- 4.1.10 P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

DSR NO.- 5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR NO.- 5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

DSR NO.- 5.33.1 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level

DSR NO.- 5.33.2 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level upto floor V level

DSR NO.- 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

DSR NO.- 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

DSR NO.- 5.9.2 Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc.

DSR NO.- 5.9.3 Shuttering for Suspended floors, roofs, landings,

DSR NO.- 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

DSR NO.- 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.

DSR NO.- 5.9.7 Stairs, (excluding landings) except spiral-staircases

DSR NO.- 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

DSR NO.- 6.1.1 Brick work with bricks of Ist class in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)

DSR NO.- 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR NO.- 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR NO.- 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

DSR NO.- 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

DSR NO.- 9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

DSR NO.- 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

DSR NO.- 9.20.3 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws

DSR NO.- 9.21.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

DSR NO.- 9.62.1 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

DSR NO.- 9.63.1 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm.

DSR NO.- 9.63.3 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm.

DSR NO.- 9.66.1 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm.

DSR NO.- 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding.

DSR NO.- 9.96 Providing and fixing aluminium door window fittings, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), complete :

DSR NO.- 9.96.2 A) 250x16 mm sliding door bolts

DSR NO.- 9.97.2 B) 250x10 mm Tower bolt

DSR NO.- 9.97.4 C) 150x10 mm Tower bolt

DSR NO.- 9.100.1 D) 125 mm handles

DSR NO.- 9.100.2 E) 100 mm handles

DSR NO.- 9.101.2 F) hanging floor door stopper, Twin rubber stopper

DSR NO.- 9.68.3 200 Casement stays (straight peg type) with necessary screws etc. complete, weighing not less than 120 gms

DSR NO.- 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

DSR NO.- 9.79.2 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm

DSR NO.- 9.114.1 Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. : Triple strip vertical type

DSR NO.- 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)

DSR NO.- 21.1.1.2 For fixed portition: Powder coated aluminium (minimum thickness of powder coating 50 micron)

DSR NO.- 21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately): Powder coated aluminium (minimum thickness of powder coating 50 micron)

DSR NO.- 21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

DSR NO.- 21.4.1 Providing and fixing double action hydraulic floor spring of approved brand and nufacture onforming to IS : 6315, having brand logo mbossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the xisting floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness

DSR NO.- 21.13 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

DSR NO.- 21.16.1 Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineerin-chargeAnodized (AC 15 ) aluminium

DSR NO.- 10.13.1 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

DSR NO.- 10.11.1 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

DSR NO.- 10.14 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:

DSR NO.- 10.14.2.1 (A) "Profile C" Fixing with adjustable lugs with split end tail to each jamb

DSR NO.- 10.15.1 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

DSR NO.- 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

DSR NO.- 9.51.2 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading

DSR NO.- 10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

DSR NO.- 10.25.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

DSR NO.- 10.26.1 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

DSR NO.- 10.30.1 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes.

DSR NO.- 10.30.2 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes

DSR NO.- 25.8 Design supply & installation of suspended Spider Glozing system designed to withstand the wind pressure as pr IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. “

DSR NO.- 11.3.1 P/L 40 mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement

DSR NO.- 11.4 52 mm thick C.C. flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4

DSR NO.- 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

DSR NO.- 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specifiedby manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm double charged

DSR NO.- 11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

DSR NO.- 11.36 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

DSR NO.- 8.2.2.1 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of approve colour.

DSR NO.- 8.2.1.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.A) Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble. Area of slab over 0.50 sqm

DSR NO.- 11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

DSR NO.- 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

DSR NO.- 22.7 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

DSR NO.- 22.7 b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

DSR NO.- 22.7 c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

DSR NO.- 22.7.1 e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

DSR NO.- 12.21 Providing gola 75x75 mm in cement concrete (1:2:4).

DSR NO.- 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

DSR NO.- 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

DSR NO.- 12.42.5.2 110 mm bend

DSR NO.- 12.42.6.2 110 mm Shoe

DSR NO.- 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4).

DSR NO.- 12.43.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

DSR NO.- 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

DSR NO.- 22.3 (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

DSR NO.- 22.3 (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

DSR NO.- 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

DSR NO.- 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

DSR NO.- 13.3.1 20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

DSR NO.- 13.16.1 6 mm cement plaster 1:3 (1 cement: 3 fine sand)

DSR NO.- 13.37 White washing with lime to give an even shade : New work (three or more coats).

DSR NO.- 13.44.1 Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm).

DSR NO.- 13.45.1 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

DSR NO.- 13.41.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer

DSR NO.- 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

DSR NO.- 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

DSR NO.- 12.54.2 Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

DSR NO.- 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

DSR NO.- 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

DSR NO.- 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

DSR NO.- 17.32.4 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Non Schedule Item P/L 110 mm dia UPVC soil waste pipe with pressure 6kg/CM2 for sewer.

DSR NO.- 17.73.2 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Non Sschedule Item P/F Upvc nahani trap 100x100mm dia

DSR NO.- 18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Non Schedule Item P/F Upvc terminal guard 100 mm dia

DSR NO.- 18.74.2 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

DSR NO.- 12.42.5.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend

Non Schedule Items P/F Upvc door bend 100 mm dia.

DSR NO.- 17.28.2.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

DSR NO.- 12.42.4.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

DSR NO.- 17.8 P/F white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

DSR NO.- 17.5.2 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

DSR NO.- 17.7.8 White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers. FOR LABS

DSR NO.- 18.11.1 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

DSR NO.- 18.1 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

DSR NO.- 18.10.2 20 mm dia nominal bore

DSR NO.- 18.10.3 25 mm dia nominal bore

DSR NO.- 18.12.5 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore

DSR NO.- 18.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

DSR NO.- 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

DSR NO.- 18.17.1.A 20mm nominal bore

DSR NO.- 18.17.1 25 mm nominal bore

DSR NO.- 18.17.3 40 mm nominal bore

DSR NO.- 18.58.1.1 Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

DSR NO.- 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

DSR NO.- 18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

DSR NO.- 18.20.3 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore

DSR NO.- 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

DSR NO.- 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Non Schedule Items P/L 150 mm dia UPVC pipe with pressure 6kg/CM2 for sewer line.

DSR NO.- 19.2.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

DSR NO.- 19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO.- 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mmnominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO.- 19.8.1.2 Extra for depth for manholes : With Sewer bricks conforming to IS : 4885

DSR NO.- 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO.- 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

DSR NO.- 6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

DSR NO.- 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

DSR NO.- 18.12.4 32 mm dia

DSR NO.- 18.12.5 40 mm dia

DSR NO.- 18.12.6 50 mm dia

DSR NO.- 18.12.7 65 mm dia

DSR NO.- 18.12.8 80 mm dia

DSR NO.- 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

DSR NO.- 18.17.2 32 mm dia

DSR NO.- 18.17.4 50 mm dia

DSR NO.- 18.17.5 65 mm dia

DSR NO.- 18.32.1 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

DSR NO.- 18.4 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

DSR NO.- 18.40.6 50 mm diameter pipe

DSR NO.- 18.40.7 65 mm diameter pipe

DSR NO.- 18.41 Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

DSR NO.- 18.41.6 50 mm diameter pipe

DSR NO.- 18.41.7 65 mm diameter pipe

DSR NO.- 2.13.1.2 Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material rmeasurements and disposal of nserviceable material as directed, within a lead of 50 m :Ordinary rock : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

DSR NO.- 19.6.4 P/L non-pressure NP2 class (light duty) R.C.C. pipes with collars. 300 mm dia

DSR NO.- 18.33.1 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

DSR NO.- 19.19.1.1 P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. Rectangular shape 600x450mm internal dimensions

DSR NO.- 19.15.1 Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar

Non Schedule Items Supply, Installation, Testing and Commissioning of Electric Driven Terrace Fire Pump suitable for auto/maual operation & consisting of following: complete in all respect as required. End suction horizaontally mounted cetrifugal type fire pump with bronzw impeller with CI body should be of grade F.G. 200 to IS : 210 casing shall be designed for 1.5 time of working pressure,capeble of delivering 900LPM against a total head 45meters whi Squirel cage,TEFC indication motor sitable for 415+ 10% 3 phase 50Hz AC supply and of apporximate suitable 50 HP (approx)for the above pump running at 2900 RPM conforming to IS : 325-1978. Common base frame fabricated out of M.S channel of suitable size, flexible coupling, coupling guard, foundation bolts and pressure gauge with valve etc. Suitable cement concrete foundation duly plastered. complete as per manufacturer's design & standards

Non Schedule Items Make : Pumps: Kriloskar/ Mather &Platt/ Gundfoss Motor: Kirloskar/ ABB/ Crompton

Non Schedule Items Starter for terrace pumo

Non Schedule Items Supply, Installation, Testing and Commissioning of Diesel Engine Driven Main Fire Pump suitable for auto operation and consisting of following: complete in all respect as required. Horizontal end suction type, centrifugal, multistage pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm. at highest and farthest outlet at specified flow of 900 lpm at 60 Mt Suitable HP 1500 RPM, 4 stroke, cold starting type Diesel Engine with Heat Exchanger confirming to relevant BIS & IS Standards, complete with all required accessories / system , fuel oil filter, lubricant oil pump with filter, 1 Nos. starting batteries of

Non Schedule Items Make : Pumps: Kriloskar/ Mather &Platt/ Gundfoss ENGINE: Kirloskar/ Mahindra/ Cummins

Non Schedule Items Fabrication, Supplying, Installation, Testing & Commissioning of Electrical Motor Control Panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalized with hinged lockable doors, dust and vermin proof, powder coated for diesel engine pump with amf option and battery charging

Non Schedule Items Make : Agni Surksha /Agni

Non Schedule Items Supply,installation,testing and commissioning of MS C class Heavy duty pipe Inclueding forged fitting such as bends, tees, reducers,welding rods,two cote red oxide peimer and one cote post office red paint,angle,fastnor,two cote black japan etc. of follow

Non Schedule Items Make : Jindal/Surya/Prakash.

Non Schedule Items 100 mm line (approx.) C Class

Non Schedule Items 80mm line (approx.) C Class

Non Schedule Items 25mm line (approx.) C Class

Non Schedule Items SITC of wrapping coating of pipe line in trenches

Non Schedule Items Supply,installation, testing and commissioning of single headed landing valve of 63mm dia. Made of SS hydrant valve complete with necessary fitting.

Non Schedule Items Make : Newage/Omex/Safe Fire/Safe Guard.

Non Schedule Items Supply,installation, testing and commissioning of RRL Hose pipe with 63mm dia. and 15mtr.length with SS male and female couplings.

Non Schedule Items Make : Newage/Omex/Safe Fire/Safe Guard.

Non Schedule Items Supply,installation, testing and commissioning of 63mm dia. SS short branch pipe nozzle suitable for instantaneous connection to hose coupling as required.

Non Schedule Items Make : Newage/Omex/Safe Fire/Safe Guard.

Non Schedule Items Supply,installation, testing and commissioning of MS hose box keeping two no.of RRL hose pipe and one no.of short branch pipe.

Non Schedule Items Providing of weather proof door cabinet for fire shaft to accomidate hydrant, hose reel, hose box etc

Non Schedule Items Supply,installation, testing and commissioning of two way fire brigade inlet connection suitable for local fire tender complete as required.

Non Schedule Items Make : Newage/Omex/Safe Fire/Safe Guard.

Non Schedule Items Supply,installation,testing and commissioning of swinging type first aid fire hose reel of 20mm internal dia and 30 mtr long with MS drum and 5mm shut of nozzle complete with fitting complete as required.

Non Schedule Items Make : Newage/Omex/Safe Fire/Safe Guard.

Non Schedule Items Supply,installation,testing and commissioning of gun matel body air release valve complete with all fitting as equired like ball vlave,holdtite,suta etc.

Non Schedule Items Make : Precious/zolto/swastik

Non Schedule Items Supply,installation,testing and commissioning of Cast Iron body Butterfly Valve complte with all fitting as requied like MS flange, nut bolts,washers etc. 100 mm

Non Schedule Items Make : Castle/Zoloto/Kartar

Non Schedule Items Supply,installation,testing and commissioning of Cast Iron body Non return valve complte with all fitting as requied like MS flange, nut bolts,washers etc. 100 mm

Non Schedule Items Make : Castle/Zoloto/Kartar

Non Schedule Items Supply,installation,testing and commissioning of gun matel body Foot valve for negitive pump suction complte with all fitting as requied like tharding niple,holdtite,suta etc. 100 mm

Non Schedule Items Make : Swastik/Royal

Non Schedule Items Supply,installation,testing and commissioning of Pressure Gauge. (0-10kg).

Non Schedule Items Make : H.Guru/Hebig

Non Schedule Items 16mm x 4core. From pump electric panel to fire pump .

Non Schedule Items Supply,installation,testing and commissioning of gun matel body Ball Valve.25mm dia.

Non Schedule Items Make : Precious/zolto/swastik

Non Schedule Items Supply,installation,testing and commissioning of pressure switch (maximum pressure range 10kg/sq high)for hydrant stand by and jocky pumps, complete as required.

Non Schedule Items Make : Indfos/Dandfos

Non Schedule Items Supply,installation,testing and commissioning of air vashal tank complete with all fitting like air release valve,ball valve,MS Flanges,holdtite,suta etc.(200mm dia x 2000mm length).

Non Schedule Items Supply,laying,testing and commissioning of cooper unarmoud cable for pressure switch connection to fire electric control panel.

Non Schedule Items 1.5mm x 2core.

Non Schedule Items Providing and fixing anti vivration mounting for pipe line

Non Schedule Items 80 mm

Non Schedule Items 150 mm dia

Non Schedule Items Earthing for the panel and motors

Non Schedule Items Earthing Strip

Non Schedule Items FIRE EXTINGUISHERS

Non Schedule Items Supply,installation of ABC type fire extinguisher. Capacity. 4kg.

Non Schedule Items Make : Gaurds/Omex/Safe Fire/Safe Guard/life guard.

Non Schedule Items Supply,installation of CO2 type fire extinguisher. Capacity. 4.5kg.

Non Schedule Items Make : Gaurds/Omex/Safe Fire/Safe Guard/life guard.

Non Schedule Items Supply,installation of M/F type fire extinguisher.capacity.9ltr.

Non Schedule Items Make : Gaurds/Omex/Safe Fire/Safe Guard/life guard.

Non Schedule Items Supply,installation of fire Bucket as per IS spacification with stand (holding four bucket).

Non Schedule Items SITC of 4 Zone Fire Alarm Panel

Non Schedule Items SITC of Manual Call Point

Non Schedule Items SITC of Hooters

Non Schedule Items SITC of Cable 1.5 mm X 2 core

Non Schedule Items SITC of Conduit

Non Schedule Items SITC of 2 X 12 AH Battery for panel

DSR No. - 16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

DSR No. - 16.3.1 Supplying and stacking of broken stone aggregate. ( 90 mm to 45 mm size stone aggregate) .

DSR No. - 16.3.1 [Grading of no-1]

DSR No. - 16.4 Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

DSR No. - 16.43.2 Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriateproportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineerin-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

DSR No. - 16.69 Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

DSR No. - 19.19.4.1 P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. EHD - 35 : Circular shape 560 mm internal dia

DSR No. - 23.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

DSR No. - 23.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge

DSR No. - 23.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge

DSR No. - 23.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

DSR No. - 23.8 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge.

DSR No. - 23.3.2 Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

DSR No. - 23.3.3 200 mm nominal size dia

DSR No. - 23.4.2 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

DSR No. - 23.4.3 200 mm nominal size dia

DSR No. - 23.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia.

DSR No. - 23.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts f required size complete. 150 mm clamp

DSR No. - 23.15.2 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I): 150 mm dia.

DSR No. - 26 Supply of all materials, labour, T&P etc and construction of R.C.C. O.H.T. of following capacities ( in kiloliters ) and 12 m. staging with 1.00 m wide R.C.C. stair case from G.L. to balcony and from balcony to top dome 1m x 1m R.C.C. landing at suitable locations and railed with 3 rows of 20 mm dia G.I. (M) pipe on 65x65x5 mm angle iron posts fixed with ladder, from top to the floor inside of the tank, M.S. M.H. cover with locking arrangement, lightning conductor as per electricity rules, water level indicator, supply and fixiing of outlet, inlet, over flow and wash out pipes with necessary sluice valves, pipe pieces (including cost of materials) flooring 0.60 M wide apron, painting on tank body vertical pipes, ladder, M.S. M.H. cover, ventilator column etc. complete with approved water proofing (apex) / enamal paint, testing, filling water for testing purpose etc. including supply of vertical pipes and specials, assuming bearing capacity as 8MT / M2 and staging 18.00 metre.

DSR No. - 26.01 50 kl (21.15+6X1.76=31.71)

Section B DSR No. - 1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

DSR No. - 1.10.2 Group B

DSR No. - 1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

DSR No. - 1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

DSR No. - 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

DSR No. - 1.14 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

DSR No. - 1.14.2 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

DSR No. - 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

DSR No. - 1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

DSR No. - 1.14.11 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

DSR No. - 1.24 5/6 amps switch

DSR No. - 1.24.1 3 pin 5/6 amp socket outlet

DSR No. - 1.24.4 Supplying and flxing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and flxing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required.

DSR No. - 1.32 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

DSR No. - 1.33 Supplying and flxing brass batten/angle holder including connection etc. as required.

DSR No. - 1.34 Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

DSR No. - 1.41 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

DSR No. - 1.45 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

DSR No. - 1.25 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

DSR No. - 1.50 Upto 450 mm sweep

DSR No. - 1.50.1 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing follwing way horizontal type three pole and neutral, sheet steel MCB destribution board, 415 V, on surface/recess, complete with tinned copper bus bar, netural bus bar, earth bar,din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator

DSR No. - 2.4.3 8 way (4 + 24), Double door

DSR No. - 2.4.1 4 way (4 + 12), Double door

DSR No. - 2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

DSR No. - 2.10.1 Single pole

DSR No. - 2.13 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

DSR No. - 2.13.1 40 amps

DSR No. - 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required

Non Schedule Items Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 2 nos. caps etc. complete (Make : Bajaj /Compton / Havells) 1200 mm sweep

Non Schedule Items Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete (Make : Bajaj /Compton / Havells) 300 mm sweep 900 rpm

Non Schedule Items Supply of 1x18 watt. Box type LED tube fitting (Make : Bajaj /Compton / Havells)

Non Schedule Items Supply Of LED Bulb (Make : Bajaj /Compton / Havells)

Non Schedule Items Supplying and Fixing of 1'x1' LED 20 watt flat panel for surface mounting which provides soft-light and glare free symmetrical illumination.(20 W , 4000 K )

Non Schedule Items Supply and Fixing of pannel board made of CRCA sheet steel with one number incomming of 250 Amp. FPMCCB and 7 Nos. outgoing of 32 amp.TPMCB and 6 Nos. of 16 Amp. TPMCB with phase indicating lamp, ammeter, Voltmeter with suitable size of bus bar completing in all respect

DSR No. - 5.4 Earthing with G.I earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt as required.

DSR No. - 5.7 S/L 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

DSR No. - 5.9 S/L 25 mm x 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering etc. as required.

Non Schedule Items S/L Aluminium conductor PVC insulated armoured, served, sheathed cable 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand around and protected with brunt bricks on side and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer- Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conducter by clamps etc.

Non Schedule Items b) (i) 10 sqmm 2 core Cat A. ( for street light)

Non Schedule Items q) (i) 95 sqmm 3.5 core Cat A. ( for Bldgs)

Non Schedule Items s) (i) 150 sqmm 3.5 core Cat A. ( for Trf. To fidder pillar)

DSR No. - 11.3 Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

DSR No. - 11.3.1 Above 4.5 meter and upto 6.5 meter

DSR No. - S.I.R. 2014-15 of UPCL Sl. No. 66 Supplying Steel tube pole STP 8.5 M-IS 410 SP-21, (for street light )

DSR No. - 12.34 S/F of 32 mm dia x 2.00 metres long G.I, pipe (medium class) brecket for mounting of fluorescent/ HPMV /HPSV street light fitting on pole including bending the pipe to the required shape, 40 mm x 3 mm flat iron clamps and wiring with 1.5 sq.mm WP/PVC wire and painting the flat iron with primer and finish paint etc. as required

Non Schedule Items Supply,Installation, testing & Commissioning of LED streetlight made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP66 protection, impact resistance of IK07 & 10 KV external SPD. (LED Lamp 48W 5700K) on 6 mtrs octagonal pole (havells catc. ref.LHETA XU7PA6W048 or equivalent)

Non Schedule Items Building LT Panel as per specification mentioned below 100 A,25 KA, 4P,MCCB - INCOMER 1no Rotating handel for MCCB 1no 100 Amp, Onload Changeover 4P 1no Operating handel for changeover 1no Multifunction Meter 1no Outgoing - 100 A, 25 KA, 4P MCCB 5no Outgoing - 63 Amp 4P MCB 5 no Outgoing - 32 Amp 4P MCB 5no

Non Schedule Items Supply,Installation, testing & Commissioning of 11/0.433kV 100kVA, Oil Cooled Transformer.

Non Schedule Items (i) Transportation of heavy duty dual Rotary Rig machine, compressor, OP unit & accessories, T&P and up to site of work and back transportation after complete of work.

Non Schedule Items (ii) Arrangement of water

Non Schedule Items (iii) Installation of ring machine, compressor & dismantling including leveling and dressing of site.

Non Schedule Items (iv) Drilling of 500/450/400/350/300 mm dia bore from G.I to 200mtr. BGL including reaming and back washing in hard bolder. Starata.

Non Schedule Items (v) Spontaneous logging & caliper logging by logger.

Non Schedule Items (vi) Lowering of tubewell assemble pipe of size 200 mm. dia M.S.Plain/slotted from G.I to 200 mtr. BGL with shrouding of pea Gravel in annular space between bore & assembly pipe.

Non Schedule Items Materail.

Non Schedule Items 200mm dia 7.9 mm thick M.S.E.R.W. plant pipe with ring.

Non Schedule Items 200mm dia 7.9 mm thick M.S.E.R.W. slotted pipe (slot size as per site. Tubewell requirement with ring

Non Schedule Items 200 mm dia heavy duty M.S. well. Clamp.

Non Schedule Items 200mm dia M.S. well. Clamp.

Non Schedule Items M.S. Girder of 8”×4” size frame (about 4 k in length)

Non Schedule Items 200 mm dia bail plug (heavy duty)

Non Schedule Items Development of tubewell by air compressor (350 PSI 300 CFM

Non Schedule Items Errection of compressor

Non Schedule Items Development of tubewell by air compressor

Non Schedule Items Dismantling of above.

Non Schedule Items Development of tubewell by O.P. unit

Non Schedule Items Installation of O.P. unit including leveling of site & equipment etc. errwction of O.P. unit.

Non Schedule Items Development of tubewell by O.P. unit.

Non Schedule Items Dismantling of above.

Non Schedule Items Chemical and Bacteriological test of water.

Non Schedule Items Survey

Non Schedule Items Hydrological/Geological Survey of SITC

Non Schedule Items Supply & Installation of Pumping Plant

Non Schedule Items Supply of submersible pump set KSB Make 250 lpm, 165 mtr. Head.

Non Schedule Items Starter cum Control Panel L&T Make for 20 HP.

Non Schedule Items Supply of 75 mm dia ERW casing coloum pipe with suitable size thick with flange 3mtr long.

Non Schedule Items Main Switch for TW.

Non Schedule Items Supply of 75mm dia DF 1.5 mtr.

Non Schedule Items Supply of 75 mm dia ISI, 1.6 Rating Reflex valve.

Non Schedule Items Supply of 75 mm dia ISI, 1.6 Rating gate valve.

Non Schedule Items Supply 75mm dia CI Tee.

Non Schedule Items Supply 75mm dia CI bend

Non Schedule Items Supply of Heavy Reducer.

Non Schedule Items Supply of Nut Bolt.

Non Schedule Items Supply of Rubber Packing of Flench

Non Schedule Items Supply of 10 sq.mm Submersible cable.

Non Schedule Items Earthing of T/w. Complete in all aspect.

Non Schedule Items Installation, Testing, Commissioing of Pumping Plant.

Non Schedule Items Running Maitainenace of Tubewell for 06 Months.

Non Schedule Items Centrifugal Pump.

Non Schedule Items S/O Control Panel with C.B one Incoming (32 A.M.C.C.B) and 2 Outgoing (16 A.M.C.B each)

Non Schedule Items Power Wiring and Earthing complete.

Non Schedule Items S/O 50mm dia Main Piping and valves.

Non Schedule Items 50mm dia C.I.D/F Sluice valve 4-2 Nos.

Non Schedule Items 50mm dia C.S Gate Valve-2 Nos.

Non Schedule Items 50mm dia C.S, S.C Gate Valve-2 Nos.

Non Schedule Items 40x50mm reducing bend-2 Nos.

Non Schedule Items 50 mm dia M.s D/F Pipe- 2 Nos.

Non Schedule Items 32x50 mm dia M.s D/F Tea-2 Nos.

Non Schedule Items 50 mm dia M.s .D/F Tea-2 Nos.

Non Schedule Items 50 mm dia M.s .D/F Pipe-2 Nos.

Non Schedule Items M.s Bolt Nut and Washer-2 Nos.

Non Schedule Items S/L of 16 sq.mm 4 Core Alu. Armourd Cable.

Makin Developers Pvt. Ltd.

M/s HC BANSAL ENGINEERS AND CONTACTORS