COMPREHENSIVE MAINT TO BLDGS OF PIONEER COY, PANCHSHUL TRANSIT FACILITY AND 2119 FD HOSP AT MIL STN DHARCHULA.

Amount

DESCRIPTION OF ITEMS

Demolition of cement concrete in ground floor,paving nexc 15cm thick(below or above GL) complete all as specified and directed.

M&L for 40 mm th PCC 1:2:4 type B1 (using 20 mm graded stone agg) as in flooring finished even & smooth using extra cement complete all as spfd & directed.

M&L cement concrete 1:4:8 type D2 (40 mm graded stone agg) as in foundation, filling and mass concrete complete all as spfd & directed.

M & L for 50mm thick PCC 1:3:6, type C-1, as in Plinth protection etc finished even & smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 metre and at change in direction complete all as specified & directed.

M&L providing cement concrete type B0, 1:2:4 (12.5mm aggregate) in roof kerbs or mud stops,coping, rounded or chamfered on edges complete all as specified and directed.

Demolition of brick work, stone/boulder masonary built in cement mortar complete all as specified and directed.

M&L for brick work with sub class 'B' brick old size bricks, straight or curved on plan exc 6 m mean radius, built in cement mortor 1:6 complete all as spfd & directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in C.M. 1:6, complete all as specified.

Taking down cement plaster on brick or stone walls, of any description including raking out joints, hacking for key, scrubbing down with water, etc complete all as spfd and directed.

M&L 10mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces including finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surface including finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for Preparing new plastered wall surfaces and applying two coat of oil emulsion distemper over a coat of wall putty of 1mm thckness over plastered surface to prepar the surface even and smooth complete all as specified and directed.

M&L for preparing newly plastered surface of wall apply two coat of cement base paint over a coat of primer complete all as specified and directed

M&L three coats of white wash on wall surfaces including prepration of new plastered surfaces complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M/L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm and not exceeding 0.18 sqm, in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as spfd & directed

M&L for vitrified ceramic light shade tiles/outdoor tiles 8-12mm thick (square or rectangular) polished area of each tile not exc.0 .36 sqm in floor etc and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade complete laid over screed bed,rendering or bedding layer of mortar CM (1:6) 15mm thick all as specified and directed

M&L for vitrified ceramic light shade tiles/outdoor tiles 8-12mm thick (square or rectangular) polished area of each tile not exc.0 .36 sqm in skiritng etc and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade complete laid over rendering in CM (1:4) 10 mm thick complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface, 450x350x7-8mm thick set and jointed in neat sement slurry and pointed in white or colour cement to match over 10 mm thick plaster in CM 1:4 complete all as spfd & directed.

M&L for Chequered coloured cement concrete tiles 25cm x 25 cm x 20-25 mm thick set, jointed and pointed in neat cement slurry with grey pigment cement and pigments in floor including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed

M&L Granite (of any type) tiles 20 mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed in CM 1:6 etc complete all as specified and directed.

Taking down chowkhats or frame nexc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sqm but nexc 4.00 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutter exc 1.0 sqm but n exc 2.00 sqm each complete all as specified and directed.

S&F for mild steel framed wk as in doors or gates of angle iron or other section complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with & incl either hooks & hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and slides) & hanging, also fastening & fixing Fe-290, Gde-165 complete all as spfd & directed.

S&F 0.63 mm th Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams,including bending or turning up, mitred angles, etc. as required complete all as spfd & directed.

S&F 35 mm th Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L for 2nd class hardwood, 35 mm thick glazed and skelton shutter, open rebated and prepared to receive glass, gauge, etc. devided into squares, with plain, chamfered or rounded , mitred and rebated shash bars any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc; size of members of shutter as specified in SSR Part I, Sectioin 8 clause 8.24(a); supplied and fitted to chowkhat complete all as specified and directed

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed

S&F Factory made solid panel pvc door shutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded all as spfd and as directed.

ditto- as sl item no 31 above but without glazing bar

S & F MS work as in window guard bars,holdfasts etc., plain, let in and fixed independently in wooden frames etc, and similar articles conforming to Fe 290 Gde E 165 complete all as specified and directed.

S&F for powder coated anodised aluminium frame for doors, windows ventilator with one or more rebates including joining cleat for fixing etc , screws, hinges, brackets, dash fastners/rawl plugs etc. complete all as specified and directed.complete all as specified and directed.

S&F powder coated aluminium door shutters, aluminium section weighing not less than 0.55 Kg/m including necessary jointing cleats glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified and directed.

M&L for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel covr, governing pivo made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F Door closer hydraulically regulated,designation No. 2,aluminium die cast body universal type complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floors 150mm long all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or descrption) from metal frame including punching or driling outold glazing pins/springs complete all as specified and directed.

S&F 4.80 mm thick sheet glass ordinary quality and glazing with oil putty/rubber packing in square exc .50 sqm in each panels complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and directed.

S&F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100 mm mild steel but hinges medium weight,cold rolled complete all as specified and directed

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

S&F 150 mm aluminium handles, cast type anodised complete all as specified and directed.

S&F150 mm aluminium anodised barrel tower bolts extruded section complete all as specified and directed

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 100 mm Mortice lock,vertical type,size 100 mm complete all as specified and directed.

S&F 100 mm Mild Steel barrel tower bolts, stove enamelled, black with bright bolts complete all as specified and directed.

S&F 150 mm Mild Steel barrel tower bolts, stove enamelled, black with bright bolts complete all as specified and directed

S&F 250mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Dismantling mild steel work of any description and in any position complete all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and gastenings and heavy brackets framing (beam, tee, angle channel or flat sections) (Fe-290 Gde E-165) inicluding distance pieces, cleats etc.complete all as specified and directed.

S&F in repairs vitreous china wash basin of size 550 x 400 mm, white flat back size with full pedestal of height 800 to 830 mm, incl 32mm size chromium plated waste fitting and waste pipe, fixed to wall with fastener / rawl plugs complete all as specified and directed.

S&F in repairs vitreous china wash basin,rectangular or oval shaped with min . Size 550X400mm incl 32mm size brass chromium plated waste fittings,waste pipe fixing in slab/granite top incl necessary fixing arrangement complete all as specified and directed.

S&F in rep vitreous china squatting pan "Orissa pattern" size 580 mm x 440 mm white with integral foot rests, incl provn of lime concrete bedding complete all as spfd & directed.

S&F in repair Vitreous China Wash down water closet EWC with plastic seat cover complete all as specified and as directed .

S&F in repair sinks made of stainless steel 1 mm th kitchen or laboratory with plugs, washers & waste coupling, incl bedding in CM to dwarf wall or incl fixing cantilever brackets & connecting union to pipe over all size 495x420mm bowl size 410x330 mmx160 mm complete all as spfd & directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F for PVC low level flushing cistern 10ltr capacity, with cyphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc as spd and fixed in repair all as specified and directed

S&F in repair Tubular towel rail brass chromium plated 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F in repair CP Towel Ring fixed with and including Chromium plated brass screws and cleats complete all as specified and directed

S&F in repair 15mm bore Chromium plated Bib taps fancy type, cast copper alloy screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified

S&F in repairs stop valve/angle valve, bore of dia 15mm of Chromium plated fancy type cast copper alloy screwed down for iron pipe and fixed etc complete all as specified and directed.

S&F in repairs Brass CP mixer fancy type for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F 15mm Pillar taps, cast copper alloy,with capstane heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete all as spfd & directed.

Supply only 15mm pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as spfd & directed.

S&F in repairs Stainless steel soap dish, any type fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified

S&F in repairs plastic water closet seat, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging devise complete all as specified and directed.

M&L for 32mm in size Waste fittings, brass, chromium plated for stainless steel sinks, glazed ware basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed in reapirs complete all as specified and directed

S&F PVC connections 15 mm size with PTMT nuts of length 600mm long fixed in repairs all as spfd and as directed.

S&F PVC waste pipe 32/40mm dia for wash basin/kitchen sink/urinals in repairs complete all as specified and as directed.

S&F in repair 25 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed in repairs all as specified and directed.

S&F in repair 20 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed in repairs all as specified and directed.

S&F in repair 15 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed in repairs all as specified and directed.

S&F swivel shower of PTMT any colour for fixng with 15mm pipe along with shower arm 15mm size 195mm long with bend of 45 degree with flage of PTMT any colour,fixed in repairs complete all as spfd & directed

S&F in repairs shower concealed stop valve, bore of dia 15mm of Chromium plated fancy type cast copper alloy with long shank and capstan head for (Bath shower) screwed for iron pipe and fixed including making good exisiting surfaces complete all as specified and directed.

S&F 15 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc including taking up or down 15 mm GI tubing complete all as spfd & directed

S&F 20 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc including taking up or down 20 mm GI tubing complete all as spfd & directed

S&F in repairs Health Faucet (ABS Body) MS, Chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

S & F in repair Harrison rails/curtain rods, mild steel, chromium plated with brackets,stops, rollers etc fancy type as approved complete all as specified and directed.

Supply and fix 1000 Ltr rotational moulded polyethylene water stotage tanks ( cylinderical vetrticle with closed top) hoisted & fixed in position including dismantlling old water tank, complete all as specified and directed.

Supply and fix 500 Ltr rotational moulded polyethylene water stotage tanks ( cylinderical vetrticle with closed top) hoisted & fixed in positio including dismantling old water tank complete all as specified and directed

Supply and fix 250 Ltr rotational moulded polyethylene water stotage tanks ( cylinderical vetrticle with closed top) hoisted & fixed in positio including dismantling old water tank complete all as specified and directed

S&F in 25 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

S&F in 20 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

S&F in 15 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

Supply and Fix in replacement mild steel lid/tank cover with hinges on one side & locking facility on another side/ or with thread for water tank of capacity upto 1000ltrs complete all as specified and directed.

S&F in repair 15mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Supply and fix in repairs CP Wall Mixer with provision for Overhead Shower with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges for 15mm dia pipe complete all as specified and directed

Demolition and breaking up drain pipes 100 mm dia(Salt glazed ware, AC or reinforced concrete) set in cement mortar etc. complete all as specified and directed.

S&F 110 mm bore PVC(SWR) pipes single sockets in any length with rubber ring joints fixed to walls or laid in floors including fixing complete all as specified and directed.

S&F 110 mm bore PVC(SWR) bend any radius complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets,fittings etc. as specified and directed.

S&F False Ceiling Horizontal level regular edge grid 600 x 600 mm form work using hot dip sections and fixing tiles vinyl laminated MPL gypsum panels size 595x595x6 to 8mm thick after lamination, suspended the grid with grid hangers to Roof Truss / RCC Slab all as spfd and directed.

S&F 5 to 8mm thick PVC hollow type wall panelling any color fixed to wall/ceiling with L or U shaped beading at ends fixed with screws complete all as specified and as directed.

M&L for 18/19mm thickness Medium density fibre board,one side laminated other side balancing, exterior grade, fixed in repair to framework with screws etc

S&F 6mm thick teak wood lipping fixed with nails to block board or veneered particle board all as spfd and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised (width of flaps 30mm) all as specified.

S&F 40mm dia cupboard knobs fixed with nut, screw and washer of mild steel bright finished complete all as specified and directed.

S&F catch magnet for cupboard shutter complete all as specified and directed.

M&L for 6mm thick Plywood, grade BWR, type BB, fixed in ceiling and walling with screws to timber frame work complete all as sfd and directed.

M&L II nd class hard wood plain fillets square or rectangular in section cleansawn but bullnosed chamfared or rounded on one edge or face sectional area exc 3 sqcm and nexc 6 sqcm secured in nails complete all as specified and directed

Dismanteling of timber scantling 40 sqcm and over in section in any position for framed works complete all as specified and directed

M&L for 2nd class hard wood as in scantling clean sawn framed & fixed as in ceiling and walling wks, complete all spfd & directed.

Dismantling of timber scantling 40 Sqcm under in section in any position, fixed with nails framed work complete all as spfd & directed.

M&L for II nd class hard wood plain fillets square or rectangular in section clean sawn secured with nails sectional area exc 13 sqcm and n.exc 25 sqcm complete all as specified and directed

M&L for one coat of creasote oil to wooden surfaces new or old of any description including prepration of surfaces complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting of any guage/thickness in roof covering/wall clading complete all as spfd and directed

S&F 0.63 mm th galvanised corrugated mild steel sheeting with two corrugation side lap fixed with 'L' type or 'J' type or cranked hook bolts fixed to roof covering/cladding to wall complete all as spfd & directed

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for two coat of synthetic enamel paint over a coat of pink primer to new/old wooden surface of any description exc 10 cm girth or width including prepration of new/old wooden surfaces complete all as specified and directed

M/L for two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces of any description over 10 cm in width or girth incl preparation of new steel surfaces complete all as spfd and directed.

M&L for Preparing old surfaces, plastered or unplasterd old decorated wall surfaces and applying two coat of oil emulsion distemper over a coat of wall putty of 1mm thckness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less that 50gm/liter and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter / 10 Sqm over and including priming coat of exterior primer applied @0.90 liter/10 Sqm over new surfaces complete all as specified and directed.

M & L for one coat of white wash on old decorated wall surfaces including preparation all as specified and directed

M & L One coat of Oil bound distemper on old decorated wall surfaces including preparation all as specified and directed

M & L one coat of Cement based paint on old decorated wall surfaces including preparation all as specified and directed

M & L preparing old previously treated surfaces of steel surface as in corrugated/plain sheets as in roof covering /wall or other surfaces over 10 cm girth or width by cleaning straightening if any removing rust and making good where required and applying Two coat of synthetic enamel paint on old steel surfaces complete all as specified and directed.

Demolition reinforced cement concrete in any description and in any position complete all as specified and directed.

M&L Slabs supported on walls,beams and columns in floors,roofs, landings,balconies,canopies, deck slabs and in shelves and the like using cement concrete type B-0 1:2:4 complete all as specified and directed

S&F Formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface of concrete complete all as specified and directed

M & L mild steel TMT bars 6 to 8mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as specified and directed

S&F in repair 15mm dia cast iron bib taps with forged brass stem & brass jumper valve, screwed for iron pipe and fixed all as specified and directed

Taking down carefully unsv copper/aluminium point wiring (light/fan/socket or power) complete, including fixture and fittings such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sketch fitting etc removing materials to store for keeping in safe custody for taking credit complete all as specified and directed.

All as per Ser item No 134 here in before but for one 5 Amp socket outlet point on same board controlled by one switch 5 Amp one way.

All as per Ser item No 134 here in before but for one 5 Amp socket outlet points controlled by one switch 5 Amps one way on independent board.

All as per Ser item No 134 here in before but for one 15Amp socket point using with 2.5Sqmm FRLS PVC insulated multi-strand copper conductor.

M & L for point wiring using 1.5 Sqmm FRLS PVC insulated unsheathed multi stranded copper conductor cable(Phase, neutral and earth wire) drawn through and incl surface PVC casing capping/ conduit of medium grade and connected to common earth dolly with high grade PVC terminal boxes of thickness not less than 1.5 mm and plastic laminated 3 mm thick sheet cover fixed with brass screws or PVC modular terminal boxes of thickness not less than 1.2mm incl modular cover plate(inner & outer) of required module for mounting modular switch/socket/regulator for one light/fan/bell point controlled by one 1way switch complete all as specified and directed. Note: 1. Conduit shall be fixed on surface with necessary saddles.

All as per Ser item No 138 here in before but for one 5 Amp socket outlet point on same board controlled by one switch 5 Amp one way.

All as per Ser item No 138 here in before but for one 5 Amp socket outlet points controlled by one switch 5 Amps one way on independent board.

All as per Ser item No 138 here in before but for one 15Amp socket point using with 2.5Sqmm FRLS PVC insulated multi-strand copper conductor.

S&F switch piano flush button single pole one way 5 Amps complete all as specified.

S&F switch piano flush button single pole two way 5/6 Amps complete all as specified.

S&F bell push flush button single pole one way 5Amps complete all as specified.

S&F switch piano flush button single pole one way 15Amps complete all as specified.

S&F socket out let 3 pin 5/6 Amps flush type complete all as specified.

S&F socket outlet 2 in 1, 3 pin 5 and 15 Amp flush type, 240 volts all as specified and as directed.

S & F stepped type electronic fan regulator flush type Socket type on the existing phenolic laminated sheet etc. not less than 100 W flush type.

Supply & fixing modular switch one way 06 Amps,1 module, 240 volts complete all as specified & directed

Supply & fixing modular socket one way 6 Amps,2/3 pin combined ,2 module, 240 volts complete all as specified & directed

Supply & fixing modular switch one way 16 Amps,1 module, 240 volts complete all as specified & directed.

Supply & fixing modular socket one way 6/16 Amps,2/3 pin combined ,2 module, 240 volts complete all as specified & directed.

Supply & fixing modular Bell Push 6A,(1 or 2 module as per site requirement), 240 volts complete all as specified & directed.

Supply & fixing modular Two way switch 6A,(1 or 2 module as per site), 240 volts complete all as specified & directed.

Supply and fixing modular blanking /dummy Plates 1 M.

Supply and fixing Modular stepped type electronic fan regulator 2 module AC, 230 volts, duly ISI marked with and including connector complete all as specified & directed.

Supply & fixing in replacement of PVC modular terminal box high grade of thickness not less than 1.2mm of 3 module including modular white cover frame with support frame and blank plate complete all as specified & directed

All as per Ser item No 157 here in before but for 4 module.

All as per Ser item No 138 here in beforebut for 6 module.

All as per Ser item No 138 here in before but for 8 module.

S&F Ceiling rose, surface bakelite, AC, 60x30mm, 3 terminals complete all as specified and directed.

S&F lamp holder PVC/poly carbonated type with back plate suitable for pendants /angular /batten fittings complete all as specified and directed.

S&F in replacemnt of Bell ding dong type complete all as specified and directed.

S&F in replacement sheet metal enclosure for DB SPN 2 way 240 Volts, single door suitable for housing MCBs complete all as specified.

S & F in replacement SPN MCB DB 4 way sheet metal enclosures double door 230 V AC, 50 Hz AC with IP 43 and IK 09 rating having fully insulated copper busbar of rating not less than 100Amps, insulated neutral bar, earth bar and cable ties for cable management complete all as specified and directed.

All as per Ser item No 165 here in before but for 6 way.

All as per Ser item No 165 here in before but for 8 way.

All as per Ser item No 165 here in before but for 12 way.

S & F in replacement DB TPN 4 way sheet metal enclosures double door 415 V AC, 50 Hz AC with IP 43 and IK 09 rating having fully insulated copper busbar of rating not less than 200Amps, insulated neutral bar, earth bar and cable ties for cable management complete all as specified and directed.

Supply and fixing Vertical Loadline sheet metal enclosure double door, Triple pole and neutral (TP&N vertical loadline) AC, 415 volts, 04 way, with 200 Amps rated copper bus bar and IP - 43 & IK 09 protection, with the inbuilt provison for fixing of 1 No MCCB of XT1160 frame suitable upto 160 Amp and 12 Nos MCBs inside of DB, including 100 Amps , 25 KA 4 pole MCCB with metal door and flush to wall/fixed on wall surface including grouting and cutting in existing wall and making good disturbed surface with two coats of white / colour washing / distempering etc to match the existing one complete all as directed.

Supply & fixing in repalcement industrial type SPN enclosure with a two pin and earth plug and socket complete with and including 20 Amps MCB, single pole, AC, 240 volts and flush to wall including cuttings & chases on wall or fixed on surface of wall and making good including two coats of white / colour washing / distempering etc to match the existing disturbed surfaces complete all as directed .

S&F in replacement MCB SP 6-32 Amps, 240volts, 10KA, complete all as specified and directed.

S&F in replacement MCB SPN 32 Amps, 240volts, 10KA, C Curve complete all as specified and directed.

S&F in replacement MCB SPN 40-63 Amps, 240volts, 10KA, C Curve complete all as specified and directed.

S&F MCB 4 pole 40 to 100 Amps, 240volts 10KA complete all as specified.

S&F in replacement sub Main Wiring with two single core FRLS PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x6 Sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 6 Sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in and including rigid non metallic PVC concealed /surface conduit of 25 mm dia, medium grade with all conduit accessories / fittings including cutting / chases in wall and making good to disturbed surfaces of wall to match with existing specification of wall complete all as specified & directed. Note - One unit of conduit along with 2x6.0 Sqmm wire and one 6.0 sqmm earth wire shall be measured as one unit.

All as per Ser item No 176 here in before but for 4.0Sqmm.

S&F in replacement 20W surface / wall mounted box type batten LED luminaire having extruded Polycarbonate housing and PC diffuser (bright white/warm white) and integrated electronic driver with high efficiency, CRI = 80 (Minimum), PF ≥ 0.90, luminous efficacy ≥ 100 lumens/Watt operating voltage 140V-240V, CCT≥5700+/-300K complete with mounting accessories internally prewired and including connecting up with cordflexible copper conductor cable of suitable size complete all as specified and directed.

S&F in replacement LED lights fitting mirror type with high out put diffuser 2 feet,1x 10W, 220V, AC decorative box type with driver with mounting accessories and connecting up with cordflexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in replacement LED bulb 12 watts,B-22 type, 220V complete all as specified and directed.

Suppy and Fixing inverter LED Bulb 12 B 22 watt having backup minimum three hours complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm panel, 36 watt, 220 V AC recessed type with high efficiency PC diffuser soft glare free bright white/warm white light complete with driver, suitable for roof ceiling including connecting up with cord flexible copper conductor cable of suitable size complete all as specified.

S&F in replacement Energy saving, surface mounted, bulk head LED luminaire 10/12 W with Polycarbonate housing and diffuser complete including connecting up with cordflexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing in replacment Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base complete all as specified and directed.

Supply and fix 3W Flexible Wall Reading Lights with On Off Switch ,Gooseneck Light - 360° Lighting complete all as specified and directed.

S&F in replacement LED bldg security lights of 35 Watt having pressure die cast aluminium housing with system lumens efficacy≥100 lumen/W, IP65 protection, IK07 rating, inbuilt electronic driver with PF>0.95 and mounting on GI bracket incl connecting up with three core twisted flexible copper conductor cable complete all as specified and directed.

Supply and fixing in replacement security light bracket made out of light grade 25 to 32mm dia GI pipe of length 0.9 mtr bend to shape and mounting on wall using clamps nut bolts etc complete all as specified and directed.

Supply and fixing in repalcement 25 wattt , IP 65 LED post Top Lantern, energy saving, environmental friendly, designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source including all accessories and mounting on exiting pipe complete all as specified and directed.

All as per Ser Item No 188 here in before but for 15Watt.

Disconnecting electrically, taking down ceiling fan from existing position, dismantling blades, servicing by cleaning oiling /greasing, replacing unsv parts, split pins, check nuts, rubber seal etc, reassembling and rehanging at same or new locations duly connected with new cordflexible copper conductor cable of size 23/.0076 from ceiling rose and testing complete all as specified & directed. Note: Spare parts other than specified will be measured and paid separately under respective items.

Rewinding of AC ceiling fan motor 1200/1400 mm sweep any make with super enamelled copper winding wire of 35SWG gauge, sleeve work, varnishing with `B' class insulation varnish, connection with flexible wire of appropriate size two core copper wire upto connector block including cutting and taking out old burnt Al/Cu winding wire complete all as specified and directed. Note : (i) Rewinding should be done at workshop

Supply only for fixing Ball bearing of suitable size/No for Ceiling fan of size upto 1400mm sweep complete all as specified and directed.

Supply only for fixing capacitor 2.5 mfd±5%, 440 Volt, AC, 50/60Hz incl PVC clamp complete and all as specified.

Supply only for fixing capacitor 3.15 mfd±5%, 440 Volt, AC, 50/60Hz incl PVC clamp complete and all as specified.

Supply only for fixing capacitor 4.0 mfd±5%, 440 Volt, AC, 50/60Hz incl PVC clamp complete and all as specified.

S&F in repalcement of fan blade set steel suitable for ceiling fan of size 1200mm sweep and colour as per site requirement complete all as specified and as directed.

S&F in replacement ceiling fan clamp assy kit (rubber real -01, MS split clamp -02 Nos, nut ,check nut, spring washer, bolt not less tha 6.0mm dia & split pin -02 Nos) suitable for ceiling fan 1200/1400mm sweep complete all as specified.

S&F in replacement ceiling fan rod heavy duty of standard dia duly drilled holes and painted ivory white of size not less than 30mm complete all a specified and directed.

Disconnecting electrically, taking down exhaust fan of size upto 450mm sweep from existing position, dismantling frame and blades, servicing by cleaning oiling /greasing, replacing unsv parts reassembling and refixing at same or new locations duly connected with new cordflexible copper conductor cable of size 23/.0076 from ceiling rose and testing complete all as specified & directed. Note: Spare parts other than specified will be measured and paid separately under respective items.

Rewinding of exhaust fan motor of size 230 to 300 mm sweep any make with super enamelled copper winding wire of 32SWG gauge, sleeve work, varnishing with `B' class insulation varnish, connection with flexible wire of appropriate size two core copper wire upto connector block including cutting and taking out old burnt Al/Cu winding wire complete all as specified and directed. Note : (i) Rewinding should be done at workshop

All as per Ser Item No 200 here in before but for 380 to 450mm sweep.

S&F in repalcement of exhaust blade set steel duly painted as per site requirement suitable for exhaust fan size 300mm sweep complete all as specified and as directed.

Supply only capacitor 1-1.5 mfd±5%, 440 VAC, 50Hz Suare shape suitable for PVC body exhaust fan 200/250mm sweep complete all as specified and directed.

Taking down flate-plate solar collector storage solar water heater of capacity upto 250ltr, dismantling inner tank and outer tank, pipe assembly, cleaning thoroughly with descaling liquid compound complete to ensure free and constant flow of water through outlet, welding of inner tank if required at site, laser/ultrasonic welding for bonding fin and raiser tube, repair of copper bracing for bonding of header and raiser making leak proof, repair & repalcement of back and side insulation material, rethreading of inlet/outlet pipe 20 mm dia, reassembling the same after replacing u/s items i.e. heating element, thermostate, toughned glass, connection pipe with clamp etc. at existing location including necessary fasteners to ensure proper safety as reqd at site, repair/welding of MS structure for collector stand, testing and commissioning after re-installation at site complete all as specified. Note: Spare parts (heating element, thermostete, toughned glass, connection pipe with clamp) will be measured and paid separately under respective items as supply only as mentioned below.

Supply only for fixing heating element of 3.0 KW for solar water heater (as per sample ISI brand) complete all as specified.

Supply only for fixing thermostat as per sample for solar water heater with temperature range adjustable from 25 to 75 degree centigrade 220 Volts AC supply complete all as specified and directed.

Supply only for fixing flate-plate collector having absorber plate with copper tubes, thermal insulation with glass wool, glazing with transparent cover to prevent heat loss and made with iron poor solar safety toughened glass, 4 mm thick with low iron, transmissivity upto 92% at near normal incidence glass as same as existing.

Supply only Heavy duty nylon threaded flexible PVC/CPVC connection pipe 25 mm dia suitable for both hot & cold watrer supply of solar water heater complete all as specified.

Disconnecting, dismantling and taking down carefully geyser of size 25 to 50 ltrs capacity from wall after unscrewing nuts/bolts etc for repairing and replacement of unsv spare parts such as NRV, safety valve, pressure release vlave incl descaling of rust and rubbish material from the inner tank and reassembling, refixing in same position with suitable size gutties/anchot bolts and nuts incl testing complete all as specified and directed. Note:- 1.Spare parts/ items other than specified will be measured and paid separately under respective items.

Supply only thermostat as per sample for geyser of capacity upto 50Ltrs with temperature range adjustable from 25 to 75 degree centigrade, 220 Volts AC supply complete all as specified and directed.

Supply only heating element ISI Marked of rating 2.0 KW of size and type as per site requirement incl rubber washers suitable for water heater storage oc capacity upto 50Ltrs complete all as specified .

S&F in replacement of chromium plated flexible connection pipes with two brass adopter for carrying hot/cold water, fixed one end at geyser inlet/outlet and other to inlet/outlet water supply point complete all as specified and directed.

Material and Labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level, conneted to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, cheek nuts and washers of galvanised or iron protected by 15 mm bore GI pipe (medium grade) and connected to main switch board as directed including concrete pit in PCC (1:3:6) type C1 precast RCC (1:2:4) type B1 cover slab 40x40 Cm x 6Cm reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifitting made out of 8 mm dia MS bar, funnle, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR part-I, 2009.

Disconnecting all electrical and copper pipe connection, dismantling carefully and taking down the indoor and outdoor units of split type AC of cap upto 2 ton Cap and servicing at site with complete cleaning and washing filters and removing of dust from outdoor/indoor unit with high pressure water jet, checking cooling coil, compressor, gas level, oiling and greasing of fan & motor, checking for any leakage and reinstalling at original location after replacing unsv spare parts and connecting with existing AC supply, testing complete all as specified and directed. Note :- 1-Spare parts other than specified shall be measured and paid separately under respective item of BOQ. 2 - Service will be done at the site.

Supply only for fixing starting capacitor and running cacacitor of 40 to 60 mfd complete all as specified & directed.

Supply only for fixing running capacitor of 20 to 36mfd complete all as specified & directed.

Supply only for fixing starting relay suitable for window type AC for any Capacity complete all as specified & directed.

Supply and fixing condensor coil for 1.5 ton/ 2 Ton window type AC/ Split Type AC complete all as specified & directed.

Supply and fixing Air filter made of PVC/Nylon fiber suitable for 1.5 / 2 Ton split type AC complete all as specified & directed by Engineer-in-Charge.

Supply and fixing in replacement Blower Motor of split type AC upto 2 Ton capacity as per exisitng specification complete all as specified and directed.

Supply and fixing indoor unit suitable for split type air conditioner of capacity 1.5/2 Ton suitable for any existing make either for invertor type/ non inverter type, 5 star rated complete all as per site requirement including all fixing accessories complete all asspecified and directed.

Taking down carefuly the hermetically sealed /Rotary compressor unit from window type/Split type Air conditioner 1.5 ton and replacing it with new reciprocating /rotary/Scroll type as per site requirement including gas welding the copper tubings and gas charging complete in all respect and testing at required pressure after re-installing at site including replacement of mounting rubber bushes, nut bolts etc and testing after installation of following capacities of compressors.

Supply & fix in replacement metal plug top 20 Amps(2P+E) for AC or geyser complete all as specified and directed.

Supply and fixing PCB for Indoor UNIT of air conditioner suitable for 1.5/2 TON AC as per site requirement complete all as specified and directed.

Labour only for servicing of Refrigerator or Deep Freezer, checking for defects if any and repacement of unserviceable spare parts complete including testing after installation at site complete all as specified and directed. Note : Spare parts shall be measured and paid seperately under respective items of BoQ.

Supply only for fixing starting/over load relay suitable for any type and capacity of refreigerators/Deep freezer/water cooler complete all as specified and directed.

Supply only for fixing thermostat switch with knob suitable for any type of refreigerators/Deep freezer/water cooler all as specified and directed.

Supply only for fixing freezer assembly as per site requirement complete all as specified and directed.

Supply only for fixing condensor fan motor with fan suitable for Double door Refrigerator of any capacity complete all as specified and directed.

Supply only for fixing Condensor fan motor for deep freezer of any capacity as per existing size & make complete all as specified and directed .

Taking out carefuly the old compressor form refrigerators /deep freezer and fixing new rotary compressor incl gas welding copper tubings and gas charging complete in all respect and testing at required pressure incl replacement of mounting rubber, bushes nut bolts etc and testing after installation. Make:- LG/Tecumseh/Emerson/Whirlpool or as per make available at site.

M&L for gas charging with suitable Refrigerant Gas R-22/R-32/R-134A after cutting/opening sealed unit (compressor) of Air Conditioner /water Cooler /Refrigerator /Deep freezer of any size/capacity/type including replacement of capillary pipe and moisture driver filter etc including crimping and re soldering to charging line after gas charging complete all as specified and directed.

Supply and fixing PCB for refrigerator of capacity from 165 to 300 Ltrs suitable for all as per site requirement complete all as specified and directed.

Labour only for servicing of self container drinking water cooler storage capacity upto 150 ltrs, dismantling inner tank and outer tank, pipe assembly, cleaning throughly with descalling liquid compound, overhauling complete to ensure free and constant flow of water through outlet, rethreading of inlet pipe 15 mm dia, thorough checking/ rectification of fault in electrical circuits and refrigeration system, replacement of compressor or other necessary parts as required, reassembling the same at existing/new location including necessary fasteners to ensure proper safety as reqd at site, testing and commissioning after re-installation at site complete all as specified and directed. Note: Spare parts shall be measured seperately and paid under relevent items as supply only.

Supply and fixing drain pipe of water coolers of size not less than 25 mm in dia, superior quality complete all as directed.

M&L for taking out carefuly the hermetically sealed defective compressor from water cooler 40/80 ltrs and refixing it after repair with factory repaired from the authorised dealer and gas charging complete in all respect and testing at required pressure incl replacement of mounting rubber, bushes nut bolts etc and testing after installation. Make -TECUMSEH/Emerson/LG/Whirlpool/Kirloskar or as per site.

Material and labour for repairing voltage stabilizer of 3 to 4 KVA capacity by replacing burnt fuse and rewinding of burnt transformer using super enamel copper wire of existing size including necessary soldering complete as directed by EIC for the following capacity of voltage stablizers.

All as per Ser item No 237 above but capacity 1 to 2 KVA capacity.

Supply and fixing plug 3 pin 16 Amp suitable at site complete all as specified and directed.

Supply and fixing plug 3 pin 6 Amp suitable at site complete all as specified and directed.

Supply and fix 0.50 sqmm 3 core copper cable multistrnded all as specified and directed.

Supply and fixing pressed steel sunken boxes not less than 1.2 mm thick with modular cover plate(inner & outer) of 3 module for mounting modular switch/socket/regulator including taking out old rusted sunken box and old cover plate , including required cutting in existing wall and making good disturbed surface , necessaery coats of white / colour washing / distempering etc to match the existing one complete all as directed.

All as per item 242 above but for 4 module.

All as per item 242 above but for 6 module.

All as per item 242 above 10 but for 8 module.

Note : Tenderers may note that amount of credit Rs 1,07,897.24 will be deducted from the total amount arrived, at the time of Acceptance of contract.

m/s RC punetha (BID ID -3519124)

M/s Karki Krishna Singh (BID ID -3519277)