Loading
Loading…
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹1.1 Cr
EMD Value
₹2.1 L
Closing Date
18 Nov 2026, 12:30 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
SRDEEG/SEE
16 conditions · 5 needing a document upload
Contractor should have to be registered with EmployeeProvidentFundOrganization (EPFO). It is mandatory for contractor tosubmit PFcodeprovided by EPFO with their tender offer. Also eachcontractor hastosubmit "UAN" of their worker with their offer and have tomentionintender document. It is mandatory. Otherwise offer will notbeconsideredfor further action and your offer will summarily be rejected.
Financial Eligibility Criteria: The tenderer must haveminimumaverageannual contractual turnover of 'V/N'or 'V' whichever isless;where V=Advertised value of the tender in crores of Rupees N=Numberof yearsprescribed for completion of work for which bids havebeeninvited. Theaverage annual contractual turnover shall be calculatedas anaverage of"total contractual payments" in the previous threefinancialyears, as perthe audited balance sheet. However, in casebalance sheetof theprevious year is yet to be prepared/ audited, theaudited balancesheetof the fourth previous year shall be considered forcalculatingaverageannual contractual turnover. The tenderers shallsubmitrequisiteinformation as per Annexure-VIB, along with copies ofAuditedBalanceSheets duly certified by the Chartered Accountant/CertificatefromChartered Accountant duly supported by Audited BalanceSheet.
As per CE/Works/HJP's letter no. ECRHQ0ENGG(CONT)/0009/2025,dated18.11.2025 "The balance sheet andall other financialdocumentsattested/certified by the CharteredAccountant (CA) tosubstantiatefulfillment of Financial Eligibility Criteriashould be withUDIN, failingwhich the offer shall be considered asincomplete and will besummarilyrejected without any further reference."
The tenderer shall posses the valid Electrical Contractor'slicenseandSupervisory License issued by any State/Central Govt.licensingboard forthe required voltage level or above with their tenderpaper.Tenderswithout valid electrical contractor's license & Supervisorylicensewillsummarily be rejected.
"ELIGIBILITY CRITERIA:- Document required to be submitted in support of Technical Eligibility Criteria: Tenderer should have completed at least one similar single work. The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender. Similar nature of works (as defined and approved by competent authority) for "Upgradation of electrical assets of stations over Sonpur Division." is (i) Erection of LT or above voltage level distribution panels. (ii) Erection and commissioning of LT or above voltage level line (over head or underground). (iii) Electrification/Rewiring service buildings, bungalow and quarters. (iv) Supply and erection of tower light. (v) Lighting of station/ Administrative building / circulating area."
17 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderers whether sole proprietor , a limited company or a partnership firm he/they should submit authentic proof in terms of partnership deed, proprietorship documents etc. along with the tender. If he/they want to act through agent or individual partners should submit a power of attorney duly stamped and authenticated by Notary Public or by Magistrate in favour of specific person whether he/she/they are partners of the firm or any other person specifically authorizing him/her name to submit the tender, sign the agreement , receive money, witness measurements, sign measurement books , compromise, settie, relinquish any claims, preferred by firm and also sign No Claim Certificate and refer all or any disputes arbitration.
Rates are inclusive of all taxes/GST, license fee, royalty charges etc. legally leviable by State, Central Govt. and/or any other local authority.
Railway Administration reserves the right to change/Alter/Cancel the tender without any notice.
Upgradation of electrical assets of stations over Sonpur Division.
L-Open-26-27-19Dt23-10-26~ECR
L-Open-26-27-19Dt23-10-26
Open
Works - General
180 Days
Saran, Bihar
₹0
₹2.1 L
23 Oct 2026
23 Oct 2026
4 Nov 2026
95 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,07,38,571.5 | ||
| — | 500.00 | — | — | ||
| Wiring for light point, call bell, fan point/exhaust fan point and 5 A plug point in a concealed with a heavy gauge PVC conduit pipe confirming to IS 9537 (pt.3)/1983 or latest, ISI mark with single core 1.5 Sq.mm copper FRLS wire (make - Anchor, Finolex, Havells, KEI, Polycab) complete with controlling modular switches and suitable board of Legrand, Siemens, L&T, Anchor, ABB, Havells, Crabtree make and 16 SWG tinned copper wire as ECC. | — | — | — | 2,47,500 | |
| — | 300.00 | — | — | ||
| Wiring for 5 pin 5 Amp. plug point with modular switch with modular plate 1.5 Sq.mm FR PVC insulated Copper conductor single core multistrand cable in concealed/surface PVC heavy gauge conduit and earthing point with 1.5 sq.mm FR PVC insulated copper wire including supply & fixing of 5 pin, 5 Amp socket outlet , 5 amp switch. piano type earthing the third/fifth pin etc. as required. Make:- Legrand, Anchor, ABB, Havells. | — | — | — | 1,00,431 | |
| — | 258.00 | — | — | ||
| Supply, fixing, connection, and testing of 6 pin 16Amp. Modular socket with modular plate point on separate circuit and modular board: Supply of modular switch socket, fuse point and fixing, testing and commissioning on separate circuit and suitable board and wiring in concealed PVC conduit by using 4 sq.mm multistrand copper wire for phase and neutral, 1 x 1.5 sq.mm PVC insulated multi-stranded copper wire for earth from MDB/SDB/Board to this separate board. All material required for the job shall be supplied by contractor, Proper colour coding as per IE rules should be followed for wiring. Make:- Legrand, Anchor, ABB, Havells. | — | — | — | 73,978.92 | |
| — | 1800.00 | — | — | ||
| Wiring for sub-main along with earth wire with the size 2X2.5 sq.mm+1X2.5 sq.mm earth wire of PVC insulated copper conductor, single core cable in concealed/ surface/recessed PVC heavy gauge conduit as required. The work shall be done as per CPWD Pt.I, manual(1972) for general specification of electrical work. All materials should be IS marked. Cable to be use of make EON/C&S/KDK/ Finolex/Anchor/Polycab/ Havell's conforming to IS 694/97 of 1.1KV grade. Switch & socket etc. shall be of Anchor/ Kona/ Roma or similar superior make and fire retardant JB/SB shall be with hylum sheet on top, Make of Conduit/ Casing Capping, Presto Plast / Malhotra/Harson/Plaza. | — | — | — | 1,92,816 | |
| — | 1500.00 | — | — | ||
| Wiring for submain along with earth wire with the size 2X4 sq.mm+1X4 sq.mm earth wire of PVC insulated copper conductor, single core cable in concealed/ surface/recessed PVC heavy gauge conduit as required. The work shall be done as per CPWD Pt.I, manual (1972) for general specification of electrical work. All materials should be IS marked. Cable to be use of make KDK/ Finolex/Anchor/Polycab/ Havell's conforming to IS 694/97 of 1.1KV grade .Switch & socket etc. shall be of C&S/Anchor/ Kona/ Roma or similar superior make and fire retardant JB/SB shall be with hylum sheet on top, Make of Conduit/ Casing Capping, Presto Plast / Malhotra/Harson/Plaza. | — | — | — | 1,88,250 | |
| — | 1300.00 | — | — | ||
| Wiring for sub-main along with earth wire with the size 2X6 sq.mm+1X6 sq.mm earth wire of PVC insulated copper conductor, single core cable in concealed/ surface/recessed PVC heavy gauge conduit as required. The work shall be done as per CPWD Pt.I, manual (1972) for general specification of electrical work. All materials should be IS marked. Cable to be use of make KDK/ Finolex/Anchor/Polycab/ Havell's conforming to IS 694/97 of 1.1KV grade .Switch & socket etc. shall be of C&S/Anchor/ Kona/ Roma or similar superior make and fire retardant JB/SB shall be with hylum sheet on top, Make of Conduit/ Casing Capping, Presto Plast / Malhotra/Harson/Plaza. | — | — | — | 2,25,628 | |
| — | 10.00 | — | — | ||
| Supply & delivery of 4 way AC MCB distribution board sheet steel phosphatized powder painted with bus bar, neutral link, earth bar & din rail conforming to IS:13032, IS:8623 complete etc. as required. Make- ABB, L&T, Siemens, Schneider, Legrand, Havells. | — | — | — | 5,257.4 | |
| — | 40.00 | — | — | ||
| Supply & delivery of single pole A.C. MCB 6-32 Amp., 240 V, 50 Hz, 10 kA conforming to IS:8828/96 complete with metal sheet enclosure (with Din Rail) etc. as required. Make- ABB, L&T, Siemens, Schneider, Legrand, Havells. | — | — | — | 8,052 | |
| — | 10.00 | — | — | ||
| Installation, testing and commissioning of MCB DB 4 way single/three phase with MCB 6/10/16 Amp. capacity on wooden/metal board including connection, earthing the body complete etc. as required. | — | — | — | 805.9 | |
| — | 250.00 | — | — | ||
| Supply & delivery of OREVA 40 W 4000 K LED Tubelight Brand: OREVA Brand type : registered Brand Catalogue Status : Catalogue not verified by OEM Selling As : Reseller not verified by OEM Category Name & Quadrant : Light emitting diode LED fixture- LED tube light (Q3) Model: silver-40W (4Ft) HSN Code: HSN not specified by seller. Make:-Havells, C&S, Bajaj, Oreva & Surya. Warranty 05 Years from the date of installation. | — | — | — | 1,94,680 | |
| — | 250.00 | — | — | ||
| Installation, testing & Commissioning of pre wired LED fitting/ CFL fittings with tube/lamp complete with all accessories on wall/bracket on rail pole including connection with 1.5 sq. mm Cu. conductor S/C stranded cable PVC insulated weather proof earthing the body complete etc. as required. | — | — | — | 9,865 | |
| — | 100.00 | — | — | ||
| Installation testing commissioning and supply of 20 W LED (4 Ft) inverter LED batten with square profile and polycarbonate channel lithium ion battery with charging time 8 hours- 10 hours and backup time upto 4 hours indoor tube light fitting. Wiring/connection of fitting with not less than 1.5 sq.mm cu. similar to Havells cat no.LHEXACP7FN1W020, Wire through PVC flexible pipes. Fixing of fitting with aluminium clamps and steel nut bolts. Luminaire warranty period will be five years from the date of Installation. Make:-Havells, C&S, Bajaj, Phillips, Crompton & Surya. | — | — | — | 37,656 | |
| — | 60.00 | — | — | ||
| Installation, testing, oiling, greasing, cleaning/replacing & commissioning of electric ceiling fan 1200/1400mm sweep & speed regulator on ceiling & wall respectively including connection with 1.5 sq.mm Copper Conductor, S/C stranded cable PVC insulated weather proof, earthing the body, complete etc. as required. | — | — | — | 4,672.2 | |
| — | 40.00 | — | — | ||
| Installation, testing, fixing & commissioning of exhaust fan 300/380/450mm sweep in the existing opening including making the hole to suitable size for above fan, making good the damage with cement concrete including connection earthing the body complete etc. as required. | — | — | — | 6,560 | |
| — | 40.00 | — | — | ||
| Fabrication, supply & fixing of Mobile/laptop charging board with 10 Nos. switches & Sockets combined modular type in two ladders 5 Nos., in each ladder with indication lamp made of 25 x 25 Sq.mm square pipe heavy duty Hylum sheet thickness 3 mm. board size 3'x2.5"x6". Make of switch- Havells, Cona, ABB, Legrand. | — | — | — | 88,760 | |
| — | 4.00 | — | — | ||
| Supply, Fixing, Testing and commissioning of LT cubical panel board of size 135x195x45 cm and thickness 2mm comprising of following 1) 4 pole 400 Amp capacity 415 volt AC MCCB-01 no. for Incoming make ABB GE Siemens, L&T, Hevells, Standard, 2) 4 pole 100 Amp capacity 415 volt AC MCCB-03 nos. for outgoing maks: ABB, GE, Siemens, LAT, Hevells, Legrand, complete in all respect 3) voltmeter (0-500 volt) with selector switch Ammeter range 0-200 Amp grade with selector switch make Kaycee, AE with CT 400/5 of make KAPPA and copper busbar 400 Amp of require size as per panel size of 3 phase and neutral with other accessories complete in all respect. | — | — | — | 2,40,680 | |
| — | 2.00 | — | — | ||
| Supplying, installation, testing & commissioning of cubicle type LT panel suitable for 415V, 3 Phase, 4 Wire 50 Hz Ac supply system, fabricated with CRCA sheet steel of 1.6mm thick for frame work and co vers, 2mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, A 5 Set 812321.00 At Par 4061605.00 having suitable Amp capacity extensible type TPN bus bars of high conductivity, DMC/SMC bus bar supports. entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Copper bus bars i/c providing following switch gears Incomer - 800A, Four Pole ACB, (Breaking capacity: Icw = Ics = Icu = 50 kA for 1 sec), MDO with MTX 1.5G, having Overload, Short -circuit & instantaneous protection with adjustable current & time delay settings, In-built neutral & earth fault protection, current metering through O-LED display, local fault annunciation through LED indication & pre-trip alarm - 1 No, 3 Phase LED Voltmeter, Cl 1 (50 - 520 Vac) - 1 Nos 3 Phase LED Ammeter, Cl 1 - 1 Nos. CT Class 1 (800/5) - 3 Nos Voltmeter Selector Switch(VSS) - 1 No, Ammeter Selector Switch (A SS) - 1 No , RYB LED indicating Lamp - 1 Set On-off Indicating lamp - 1 Set 2A, 10 kA SP MCB for Protection - 4 Nos TPN Copper bus bars of minimum of 800Amps capacity 800A, 4Pole On-load Changeover switch (Manual)- 01 No Outgoing: 1) MCCB: 400A 4Pole, (TM), 36kA breaking capacity (Ics=100% Icu), with with factory made Silver plated Copper spreading links & Rotary handle - 3 Nos. 2) MCCB: 250A 4Pole,(TM), 25kA breaking capacit y (Ics=100% Icu), with with factory made Silver plated Copper spreading links & Rotary handle - 1 No 3) MCCB: 200A 4Pole, (TM), 25kA breaking capacity (Ics=100% Icu), with with factory made Silver plated Copper spreading links & Rotary handle - 3 Nos. 4) MCCB: 100A 4Pole, (TM), 25kA breaking capacity (Ics=100% Icu), with with factory made Silver plated Copper spreading links & Rotary handle - 6 Nos. All MCCBs should ha ve variable thermal setting of 80-100% for overload protection. Make of all switchgear items L&T, Havells, ABB, Schneider, Siemens, Legrand. | — | — | — | 15,07,506 | |
| — | 30.00 | — | — | ||
| Provision, Fabrication and commissioning of 11 KV 3 phase Gang Operated Switch on the top portion of pre-erected H- pole/4 pole structure capacity 400 Amp conforming to IS: 1818 complete with drop out fuse conforming to ISS-9835 (Pt.II) of 1980 along with mounting channel/angle iron insulator etc. all respect including supply of all required material. | — | — | — | 2,53,260 | |
| — | 28.00 | — | — | ||
| Supply and fixing of 3 pole isolator 63 Amp. Make- Legrand, ABB, Siemens & Havells | — | — | — | 17,696 | |
| — | 20.00 | — | — | ||
| Supply, delivery & Fixing of octagonal pole hot Dip Galvanized in single dip average 70 micron DFT, designed for maximum wind speed of 169KM/Hr.,BOP-7030 type pole of 6 m long, top dia 70mm, bottom dia. 130mm sheet thickness 3mm, in single section with Base plate (220x220x12)mm (LxBxT) with 4x20mm dia. 700mm long with 100mm projection foundation bolt complete with smart pack junction box with bakelite sheet, 6A MCB & stud terminals (for mounting inside base component of pole) and internal wiring for terminal to fitting with 2x2.5 sq.mm cable including single arm 1 mtr. long suitable for 3 to 10 mtr. pole of reputed make. Make - Bajaj, Transrail, Bansal, Jindal, Gammon Group & Surya. | — | — | — | 2,37,620 | |
| — | 20.00 | — | — | ||
| Making of foundation suitable for 3 to 8 mtrs. octagonal pole as per site in- charge/4'X4'X4'manufacturer dimension & as per site requirement | — | — | — | 98,100 | |
| — | 30.00 | — | — | ||
| Supply of (out door) 45 W LED street light luminaire made of pressure die cast aluminium housing LED street light luminaires with IP66, with five year warranty Surya Product Code- SLE UL 45 W IP66 LXN. Make of luminaire & Tube- Philips, Surya, Bajaj, Crompton Greaves & Havells. Warranty/Guarantee 05 Years from date of installation. | — | — | — | 1,23,960 | |
| — | 20.00 | — | — | ||
| Installation, testing & Commissioning of LED street light fitting complete with all accessories on wall/ on rail pole/tubular pole including connection with 1.5 sq. mm Cu. conductor S/C stranded cable with heavy duty conduit pipe PVC insulated weather proof earthing the body complete etc. as required. | — | — | — | 5,400 | |
| — | 50.00 | — | — | ||
| Supply & fixing of 32mm diax2 mtrs. long G.I. pipe medium class of thickness 3.25mm (approx.) bracket for mounting of HPSV/Street light F.L. fitting on rail pole or wall including bending the pipe to the required shape, 40x3mm flat iron clamps and wiring with 1.5 Sq.mm W.P. PVC insulated copper conductor single core stranded cable and painting the flat iron primer and finished paint complete etc. as required. Make of GI pipe TATA/Jindal. | — | — | — | 18,500 | |
| — | 40.00 | — | — | ||
| Supply & delivery of LED flood light fitting 250 watt. Make:-Havells, C&S, Bajaj, Phillips & Surya. Warranty 05 Years from the date of installation. | — | — | — | 5,95,021.2 | |
| — | 30.00 | — | — | ||
| Supply & delivery of LED flood light fitting 70 watt. Make:-Havells, C&S, Bajaj, Phillips & Surya. Warranty 05 Years from the date of installation. | — | — | — | 1,87,654.5 | |
| — | 5.00 | — | — | ||
| Supply, fixing, testing and commissioning of 4 pole side handle operated change over switch 200 Amp., Make - L&T, Siemens, Legrand (MDS), ABB, Schneider. | — | — | — | 72,250 | |
| — | 3.00 | — | — | ||
| Supply, fixing, testing and commissioning of 4 pole side handle operated change over switch 400 Amp., Make - L&T, Siemens, Legrand (MDS), ABB, Schneider. | — | — | — | 62,100 | |
| — | 30.00 | — | — | ||
| Supply of 9 KA lighting Arrester (Line type) suitable for 11 Kv line as per IS: 3070 latest including testing and commissioning. Make - L&T, Siemens, Legrand (MDS), ABB, Schneider. | — | — | — | 82,500 | |
| — | 200.00 | — | — | ||
| Earthing with perforated G.I. earth pipe 4.5 mtrs. Longx40mm dia with minimum 3.25mm thick including accessories and providing masonry enclosure on top with cover plate having locking arrangement and watering pipe including supply & using salt and charcoal for pipe earth electrode complete as per Genl. Spec. of elect. Work & drawing etc. as required. so that the earth resistance value should be within 2 Ohms. Make of GI pipe TATA/Jindal or equivalent superior make. | — | — | — | 3,58,900 | |
| — | 2000.00 | — | — | ||
| Supply and laying 25mm X 5mm G.I. Strip at 0.5 metre below ground level/surface as strip earth electrode including jointing etc. as required. | — | — | — | 2,12,900 | |
| — | 4000.00 | — | — | ||
| Laying of the cable partly through trench at a depth of one meter and filling with suitable cushioning materials or under the road by laying through suitable size of G.I pipe at a depth of one meter or at a platform /road/wall where excavation of one meter is not possible only cutting of the surface to the size of cable with at least two inch covering by concrete is required and refilling with earth and partly of the rail /lamp post/PF color /wall with supply of clamp made of MS flat 35x6 mm with nut -bolts adequate number with maximum space of one meter /wherever feasible etc. required . In case due to space constraints more than one cable is required to lay in one trench, payment will be released in form of length of trench and not in length of underground cable. | — | — | — | 4,29,360 | |
| Each Span | 100.00 | — | — | ||
| Cutting, removal & shifting of rail pole from site | — | — | — | 63,200 | |
| Each Span | 100.00 | — | — | ||
| Removal of ACSR over head conductor from existing rail pole. | — | — | — | 39,400 | |
| Each Span | 100.00 | — | — | ||
| Dressing and of shifting of various size of LT XLPE cable to make aesthetic of power panel and service building. | — | — | — | 39,400 | |
| — | 100.00 | — | — | ||
| Supplying and laying of approved make HDPE pipe as per IS:4984 and IS:14333 with latest amendment for installation of submersible pump with necessary connection, socket/couplings, tees, etc. as required (PE-63 & working pressure 6gf/sq cm) 25 mm outer dia. | — | — | — | 5,800 | |
| — | 6.00 | — | — | ||
| Supply & fixing of bus bar chamber with 4 strips bus bar of length 300 mm made of copper strips suitable for 100 Amp. capacity complete with all accessories including connection, earthing the body complete etc. as reqd. Make - Standard/Havells/C&S. | — | — | — | 29,914.38 | |
| — | 6.00 | — | — | ||
| Supply & fixing of bus bar chamber with 4 strips bus bar of length 300 mm made of copper strips suitable for 200 Amp. capacity complete with all accessories including connection, earthing the body complete etc. as reqd. Make - Standard/Havells/C&S. | — | — | — | 50,310 | |
| — | 6.00 | — | — | ||
| Supply, fixing, testing & commissioning of MCCB 200 Amp. Capacity triple pole 415V 50Hz with magneto, thermal release range 160-200 Amp, as desired by Rly., authority breaking capacity at 415 volt 35KA in cubical panel board including connection etc. as required Make- HPL, L&T, Siemens, Legrand, ABB, Schneider. | — | — | — | 44,553 | |
| — | 6.00 | — | — | ||
| Supply, fixing, testing and commissioning of 4 pole side handle operated change over switch 400 Amp., Make - L&T, Siemens, Legrand (MDS), ABB, Schneider . | — | — | — | 1,24,200 | |
| — | 2.00 | — | — | ||
| Supply, installation, testing & commissioning of 2 way Supply of approved make powder coated sheet steel encloser SPN MCB DB inclusive of busbar, neutral bar, earthbar, connection copper wire not less than16sq.mm & two earth terminals etc. complete as per IS:13032 (exclusive of MCB & isolator) . Make ABB, Schneider, legrand & L&T. | — | — | — | 894 | |
| — | 60.00 | — | — | ||
| Supply and delivery of 2 x 16 sq.mm aluminium cable. Make - RR KABEL, HAVELL's, POLYCAB & KEI. | — | — | — | 6,480 | |
| — | 100.00 | — | — | ||
| Supply and delivery of 2 x 95 sq. mm, Copper cable. Make - RR KABEL, HAVELL's, POLYCAB & KEI. | — | — | — | 5,67,600 | |
| — | 100.00 | — | — | ||
| Supply and delivery of 2 x 150 sq. mm Copper cable. Make - RR KABEL, HAVELL's, POLYCAB & KEI. | — | — | — | 8,92,000 | |
| — | 1000.00 | — | — | ||
| HD D Machine for Horizontal boring of Railway across the Embankment /Road at a depth of 2.02 mtr. Below GL by contractor's own arrangement:- (450/300 mm dia hole) direction of site Engineer's in-charge at site. | — | — | — | 12,17,000 | |
| — | 1000.00 | — | — | ||
| Supply, fabrication and fixing of cable tray with Rail pole at height 5.5 Mitrs. with suitable arrangement of L type G.I angle channel of size 50X50X6 mm size with G.I flat strip of size 50X6 mm thickness at a distance of 200 mm as per site requirement. Make - Lgrand, Havells, ABB, Scheineder. | — | — | — | 15,38,950 | |
| — | 1.00 | — | — | ||
| Supply of ACSR Wolf Conductor. Make- Alcor, Apar, Sterlite, Lumino, Hindustan Insulators & Industreis & Univarsal cable. | — | — | — | 2,30,550 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_April-2022_2022_CE-I_CT_GCC-2022_POLICY_27_04_22.pdf
ATTACHMENT
GCCACS1-9.pdf
ATTACHMENT
Advancecorrectionslipno.10.pdf
ATTACHMENT
GCCACS11.pdf
ATTACHMENT
TenderdocumentPH-36Electricalassets.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .