SPECIAL REPAIR TO BUILDING NO. P-658, BATHROOM OF P-358 (TRG CELL) OF 221 FD REGT AND PROVN OF CERTAIN MINOR WORK AND REV WORK UNDER AGE B/R-I AT CLEMENT TOWN, DEHRADUN.

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level)

Demolition of cement concrete (unreinforced)Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspendedwork

Dismantling timber scantlings (unframed work) 40 Sq cm and over in section in any position

Demolition of brickwork or stone/boulder masonary, built in lime mortar including quoins, arches, pillers etc, but excluding ashlar facings, dressed stone work and precast concrete article built in cement mortar or cement lime mortar

Taking down cement or cement lime plaster on brick or stone walls etc.

Taking down chowkats or frames n exc 1.5 sqm with shutters(without taking off shutters from the frames)

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm with shutters(without taking off shutters from the frames)

Dismsntling cast iron pipe 100mm bore fixed in any position including all fittings complete all as specified and directed

-Do- but 75mm dia.

S & F 100 mm Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors

- Do- but 75mm bore

S & F 100mm Cast iorn ovel access door bends diminishing pieces or tapers complete all as specified.

S & F 75mm Cast iorn ovel access door bends diminishing pieces or tapers complete all as specified.

S & F 100mm Cast iornr bends diminishing pieces or tapers complete all as specified.

S & F 75mm Cast iorn bends diminishing pieces or tapers complete all as specified.

S & F 100mm Cast iorn branch pieces, single (equal or unequal), ordinary or iverted (spigot or socket type) or with parallel branches complete all as specified.

S & F 75mm Cast iorn branch pieces, single (equal or unequal), ordinary or iverted (spigot or socket type) or with parallel branches complete all as specified.

S & F 100mm Cast iorn cowls complete all as specified.

S & F 75mm Cast iorn cowls complete all as specified.

S & F 100mm Cast iorn traps P or S complete all as specified.

M & L Brick work with subclass B bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6

Providing cement concrete type B1, 1:2:4 (20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges

M&L PCC 1:2:4 type B0 (12.5mm graded aggregate) as in sub base of floors 25mm thick

M & L 20-25mm thick machine cut kota stone slab flooring over cement 15mm thick screed bed (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M & L Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc,including cement screed 15mm thick in CM 1:6 bedded set jointed in neat cement slurry and pointed in white or coloured cement to match

M & L Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in wall etc,including 10mm thick rendering in CM 1:4 bedded set jointed in neat cement slurry and pointed in white or coloured cement to match

M & L Glazed ceramic coloured tiles in vertical surfaces 350 x 250x 7 mm/ 450 x 350 x 7 mm thick in wall and ,including 10mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match

S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides (Make : Greenply, Century, Action tessa)

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed stainless steel wire staples/xpm

S&F MS butt hinges 100mm long medium weight cold rolled complete all as specified and directed.

S&F aluminum anodized barrel tower bolt 200mm long of extruded section complete all as specified and directed.

S&F aluminum anodized sliding door bolt 300mm long with hasp and staples (bolt type) and fixing clips of sheet cast of extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F aluminum bow handle "D" type anodized 150mm long complete all as specified and directed.

Prepration of wood or wood based materials of any descriptions and applying 2 coats of synthetic enamel paints over a coat of pink primer on new surfaces.

Prepration of wood or wood based materials of any descriptions and applying 2 coats of synthetic enamel paints on old surfaces of wood.

S & F Powder coated Anodised aluminiumdoor shutters window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc. complete all as specified

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S & F Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M & L 10mm thick rendering (1:3) in ceiling surface on fair faces of concrete surfaces finished even and smooth (without using extra cement)

M & L 15mm thick rendering (1:4) on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement)

M & L 15mm thick rendering (1:6) on fair faces of brick work or concrete surfaces finished even and smooth(without using extra cement)

M & L Preparing new surfaces of wall and applying two coats of wheather proof exterior emulsion paint over a coat of white cement wash on wall surfaces complete all as specified and directed

M & L for Complete removal and Preparing old surfaces of wall and applying two coats of wheather proof exterior emulsion paint over a coat of white cement wash cement on wall surfaces complete all as specified and directed

M & L preparing new surfaces of walls and applying two coat of OBD over a coat of 3 mm thick Birla white putty.

M & L for Complete removal of old surface of wall and applying two coat of oil emulsion distempering over a coat of 3 mm thick Birla white putty complete all as specified

M & L Preparing new surfaces of wall and applying three coat of white wash on ceiling.

M & L Preparing old surfaces of wall and applying one coat of white wash on ceiling.

Preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth applying two coat of synthetic enamel paint over a coat of red oxide or zinc chrome

S & F Hard drawn steel wire fabric wt not less than n exc 4 Kg per Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E 165 includind dismantling existing mild steelwork in any position, complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connection incl removal to store

Taking up or down 20mm dia steel tubing and connection incl removal to store

S & F 15mm dia GI tube medium grade galvanised with all fittings fixed complete to walls and ceilings or laid in floors.

S & F 20mm dia GI tube medium grade galvanised with all fittings fixed complete to walls and ceilings or laid in floors.

S & F in repair 20mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed.

S & F in repair 25mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed.

Cutting chases, pinning in brick wall and making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills sunshades, shelves lintels etc and cutting chases for concealed water pipe etc and making good cutting not exc 10cm girth.

S&F in repair vitreous china wash down water closet pan pedestal pattern white including fixing with trap including PVC matching seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F in repair vitreous china squatting pan 'Orissa' pattern size 580 x 440 mm white with integral footrests and including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor

S & F in repair PVC low level flushing cistern 10 ltr capacity white colour incl with inlet ball, valve, float and handle including bracket, flush pipe of polyethylene of low or high density or PVC pipe 32mm dia for low level cistern complete

S & F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets

S & F in repair 15mm fancy type chromium plated Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F in repair 15mm fancy type chromium plated Stop valves, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type

S & F in repair 15mm fancy type chromium plated Stop valves,(concealed type) cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type

S & 15mm dia and 450mm long connection pipe with PTMT nuts at both ends.

S & F in repair 15mm dia fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed but fancy type

S&F in repair 20 mm dia and 600mm long between flanges brass chromium plated tubular towel rail.

S & F in repair 32mm waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms)

S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints any size, including fixing to steel pipe or union.

Dismantling old water tanks and S&F rotational moulded,multilayer HDPE water storage tank of 1000 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed. Make : Syntex or equivlent make of Marc/Kohler

M & L Makrana white Marble work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following type

S & F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165

M & L 10mm thick rendering in CM ( 1 : 3 ) mixed with water proofing compound on fair faces of brick walls or conc surfaces and finished even & fair complete all as specified.

Supply only liquid water proofing compound complete all as specified and directed

M & L for plain cement concrete Nominal mix (1:5:10) type E2(using 40 mm graded brick aggregate) as in sunken floor including demolition of existing cement concrete and rubbish off the premices complete all as specified and directed

M& L for two coats of elastomeric compound ie super latex of Dr Fixit or equavalent on concrete surfaces after cleaning of sunken surface (vertical and horizontal) by removing all the loose mortar, laitance, dirt, dust etc by chiesel hammer/wire brush anc air blower machine complete all as specified and directed

M&L 50mm thick PCC (1:3:6) type C-1 (Using 20mm graded stone aggregate) as in plinth protection /hardstanding , laid in panels, finished the top surfaces even and smooth without using extra cement complete all as specified and directed.

M & L hard core broken bricks gauge n exc 63mm deposited spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface.

M & L 75MM thick cement concrete type D-2, 1:4:8 finished even and rough for sub base

M&L polished rubber moulded coloured machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming IS 15658-2006 of 60mm thickness, M-35 grade laid over and incl 25mm thick sand cushioning complete all as specified and directed.Make- ferocon/jain tile industries/nitco

Dismantling AC (corrugated or semi corrugated) sheets/ galvalume sheet in roof covering including ridge of any description complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F mild steel work in framing, purlin using section such as angle, hollow pipes , flats , etc using Fe-290 grade E-165 complete.

M & L three coats of whitewashing to new plastered surfaces of walls after preparation of surfaces.

M & L one coat of whitewashing to old decorated surface walls after preparation of surface

S & F in repair Vitreous China urinals, half stall type complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with CP Urinal spreader, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S & F in repair 15mm fancy type chromium plated Stop valves, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type

S&F in repair CP health faucet with 1.00m flexible tube and wall hook complete all as specified and directed. Make : Jaquar ALD CHR 583 and equivalent

S & F Mild steel powder coated peg set of six of approved quality fixed wilth all as per directions

S & F in repair Soap dish, vitreous China white, approximate size 160x160x90mm

S & F swivel shower of PTMT any colour for fixing with 15mm pipe (min weight 40 gms) including shower arm 15mm size 195mm long with flange of PTMT any colour (min wt 40gms)

Taking up 80 mm cast irong water mains (including all fittings), with spigot and socket ends and lead joints including burning out joints and recovering lead.

Taking up 100 mm cast irong water mains (including all fittings), with spigot and socket ends and lead joints including burning out joints and recovering lead.

S & F 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F 75mm Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, inclu nut and bolts and securing ends of stays to wall or roof

S & F 100mm Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, inclu nut and bolts and securing ends of stays to wall or roof

S & F 75 mm PVC (SWR) bends any radius

S & F 110 mm PVC (SWR) bends any radius

S & F 110 mm PVC (SWR) junction single, door (Single T) equal or unequal

S & F 75 mm PVC (SWR) junction single, (Single T) equal or unequal

S & F 75 mm PVC (SWR) door bends any radius

S & F 125/110 mm PVC (SWR) P Traps long arm

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) n.exc 1.5sqm each and removing to store complete all as specified and directed.

S&F solid PVC door frame old size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, fixed in opening as per specification & drawing shown in section 8 of SSR Part II complete all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails .MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail ,bottom rail and lock rail, Paneling of plain colour PVC sheet to be fitted in MS frame welded with and including stainless steel hinges 100mm medium weight complete all as specified and directed.

M&L 150 mm long aluminum anodized barrel tower bolts of extruded section complete all as specified and directed

S&F 150 mm long aluminum handles fabricated type anodized complete all as specified and directed.

S/Fstainiless steel butt hinges medium wt cold rolled 100 mm long.

S&F steel ventilators top hung shutter including hinges and peg stays etc

Supply and fixing in repairs 3mm thick sheet glass not exc 0.50 sqm each ordinary quality fixed with putty.

M&l Prep of steel surfaces exc 10 cm width or girth and applying two coats synthetic enamel paint over a coat of red oxide primer.

M & L 10mm thick rendering in CM ( 1 : 3 ) mixed with water proofing compound on fair faces of brick walls or conc surfaces and finished even & fair complete all as specified.

M& L for two coats of elastomeric compound ie super latex of Dr Fixit or equavalent on concrete surfaces after cleaning of sunken surface (vertical and horizontal) by removing all the loose mortar, laitance, dirt, dust etc by chiesel hammer/wire brush anc air blower machine complete all as specified and directed

S&F aluminum anodized powder coated door shutter with frames of size - 40x45x1.8 mm incl. screwing of frame glass necessary joints cleats, glazing clips rubber packing, snap beading, suitable handle, tower bolt, SS butt hinges,mortice lock 4 lever with 65 mm latch size including aluminium anodized door frame of size 60x 40 x1.8 mm thick fixed to wall with necessary screws and plug complete all as specified & directed. (rates for one no hydraulic door closer per shutter & 5 mm thick tinted glass /4mm thick ACP sheet reqd to be fitted in shutters is included in the item )

S&F 4mm thick 'E' board non asbestos type of size 595mmX595mm any colour and designer type as approved by Engr-in-Charge fixed in position complete all as specified and directed.

S & F powder coated GI snap grid 600mm x 600mm size using wall angle 25mm x 25mm, main T 32 x 20mm, cross T 25 x 20mm fixed in ceiling with suitable arrangement such as 2 mm thick GI wire all as specified and directed

M&L dura stone tiles approved make of size 300x300x8mm thick as in floor over and including 15mm thick screed bed in Cement mortar (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge , Gutter, Gable flashing, corner flashing etc, fixed with self tapping screws as specified and directed.

S&F Fe 290 (dge E-165) Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

Excavating in post holes (or similar holes) soft loose soil/hard dence soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface.

M&L 15mm thick screed bed in Cement mortar (1:6) in flooring complete all as specified

M & L 10mm thick cement plaster in CM 1:4 as in skirting/dado complete all as specified

M&L Vitrified tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed. directed by Engineer-in-Charge. Make : kajaria (premier quality) , Orient

M&L for preparation of old plastered/ treated surfaces and applying one coats of oil bound distemper complete all as specified and directed.

Dismantling and taking down carefully U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed.

Dismantling and taking down carefully sub-main wiring/service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified

Material and labour for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of CI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLS ) as earth wire connected with main common earth dolly complete all as specified and directed for the following :-

One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5 Amp.

One 3pin 5 Amps socket out let on same board controlled by one, one-way Piano type switch complete all specified and directed.

One 3pin 5 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all specified and directed .

All as per item No 131 above but with 2.5 Sqmm PVC insulated FRLS cable for 15 Amps power point.

Supply and fixing switch piano flush type single pole, one-way 5 Amps, 240 Volts AC

Supply and fixing switch piano flush single pole, one-way 15 Amp, 240 Volts AC

Supply and fixing socket out let 3 pin 5 Amps flush type all as specified.

Supply and fixing in repair socket out let 2 in 1,3 pin , 5 Amp and 15 Amp flush type (multi) all as specified.

Supply and fixing in repair stepped type electronic fan regulator flush socketed type all as specified. Make -Anchor/C&S/CONA

Supply and fixing ceiling rose 3 terminals PVC / Polycarbonate, isolated body all as specified

Supply and fixing batton/angle holder insulated bodywith back plate suitable for batten fittings all as specified

Taking out ceiling fan from existing building again refixing the same ceiling fan connecting up including provision of cable flexible 3 core of suitable size wire from ceiling rose to connect fan.

S& F in repair wall mounted LED batten Box type fitting Blu colour end caps pre-wired LED fitting all as per cat part No DMLN 1 LT 8-16 with & including LED T8 tubular lamp of Cat part No LGT8-20-865-2 OF MAKE Crompton or equivalent make in philips / Havells /

S& F in repair oval shape Bulk head Edge-lit LED fitting comprising with high brightness LED 10 watt, IP-67 protection all as per cat part No- LBHP-10-CDL of make Crompton / or equivalent make in philips / Havells / C&S.

S & F in repair LED building security light with bracket and fixing arrangements 25 watt LED with bracket complete all as specified and directed. Cat Part No LSTS-25 CDL-M of Crompton or equivalent make in Havells/ C&S

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated busbar all as specified and directed .Make- legrand/ Hair/ Schnider

Supply and fixing in repair MCB 6 to 32 Amp 'C' series 10 KA repturing capacity complete all as specified. Make legrand / Hair, Schnider

Supply and fixing MCB isolator SPN 40 Amp 240 V AC 10 KA repturing capacity all as specified.

Supply and fixing sheet metal enclosure double door type for MCCB DB VTPN 4 Way with 160 Amps , 36KA, 4 Pole MCCB of Make legrand, Hair, Schnider all as specified and as directed.

Supply and fixing sub main wiring two single core 4 sq mm PVC insulated unsheathed stranded copper conductor cable ( FR ) 1100Volts grade drawn in & including rigid PVC casing/ caping /conduit 20mm dia or more medium grade surface/ Recessed in wall as per existing along with 4.0 Sq mm PVC insulated unsheathed copper conductor cable (FR ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed

Supply and fixing sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable ( FR ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FR ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed

M&L for earthing complete with galvanished steel earth plate electrode 600x600x6.0 mm thick buried directly in ground and earth pit not less than 2.25 mtr deep below NGL and top edge of the plate not less than 1.5 Mtr deep below NGL, surrounded with adequate qty of char coal dust mixed with salt to a packed thickness not less than 15 Cm on all sides of earth plate incl excavation, earth work, returning filling in , removal of surplus soil to a distance in n.exc. 50 mtr incl GI wire 4mm dia nut bolts etc to earth plate one end connected to continuous earth wire incl GI pipe watering light grade with CI funnel and wire mesh and PCC 1:2:4 type B-1 as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1 duly re-enforced with MS bar 6mm dia @ 150mm C/C both ways with 10mm dia MS bar lifting handles, all as described in electric plate No. 3 of SSR part-I complete all as specified and directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 4 way with 200 Amps rated bus bar. all as specified and directed .Make- legrand cat no 607715/ Hair/ Schnider

Supply and fixing MCB 6 to 32 Amp 'C' series 10 KA repturing capacity complete all as specified. NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed. 2. Unless otherwise specified the rates for PCC/RCC shall deemed to include the cost of formwork shuttering etc., required for complete and proper execution of the work. Refer Schedule "A" notes for details.

Nanda Brothers

P K ASSOCIATES

nautiyalandcompany

M/s RK ENTERPRISES