C/o Sarai Bhawan Near Guru Ravi Dass Temple Bhawarna Dev. Block Bhawarna Distt. KIangra H.P.

Amount

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, shuttering and pumping out water upto any depth or any quontam of water including slush which may be arise during de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as direction of Engineer-In-Charge and retuning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rates inclusive of octori, royality, Malkhana, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement isto Four sand isto Eight graded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Random rubble masonry / polygonal rubble masonry ( un coursed / brought to courses ) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 ( one cement: six sand : twelve graded stone aggregate 20mm(twenty milimetre) nominal size ) at plinth level in cement mortar 1:6 ( one cement: six sand) and curing complete within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation footings, bases of columns and mass concrete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including mouldings, cornices etc; whereever required within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels window sills, cornices, arches corbelling including curved surfaces where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like including mouldings where ever required as per architectural drawing and the like floor etc. within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimeters) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in work in edge of slab and breaks in floors and walls of any thickness within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) with cement contents not less than 330 kg (Three hundred thirty kilogram) per cubic meter to give an smooth surfaces mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like and mass concrete in all depth / thickness upto all floor level within all leads, lifts of materials and other incidentals. as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts for all floors heights in all depth / thickness within all leads, lifts of materials and other. incidentals. as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves their supports balconies, beams, girder, bressumers and cantilevers in all depth / thickness upto all floor level etc; within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in Stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor level within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing Tor steel reinforcement of Sail / Tisco for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floors within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Second Class Bricks work using common burnt clay building bricks in super-structure upto all floor level with Cement Mortar 1:6 (One Cement : Six Sand) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing Sal wood work in frames of doors, windows, clearstory windows and other frames wrought, framed and fix in position within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing 40 mm x 3 mm ( forty millimetre into three millimetre) flat iron hold fast 40 cm ( forty centimetre) long including fixing to frame with 10 mm ( ten millimetre) bolts and nuts and wooden plugs and embedding in cement concrete blocks 30 cmx30cmx15cm ( thirty centimetre into thirty centimetre into fifteen centimetre) in 1:3:6 ( one isto three isto six) graded stone aggregate 20 mm ( twenty millimetre) nominal size within all leads and lifts. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 40 mm (forty millimetre) thick panelled glazed or panelled glazed shutterfor doors, windows and clerestory windows in black enamelled iron butt hinges with necessary screws within all leads and lifts as per the direction of Engineer-in-Charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing wire guage shutter using galvenised M.S. wire guage of I.S. guage designation 85-G (eighty five -G) withwire of dia 0.56 mm ( zero point fifty six millimetre) in doors ,window and clerestory windows incliding black enamelled iron butt hinges with necessary screws within all leads and lifts as per the direction of Engineer-in-Charge.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. grill of required pattern in wooden frame window etc. with M.S. flat,square or round bar with round headed bolt and nut or by scrwes plain grill within all leads and lifts.The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. sliding door bolts anodized colour and shade with bolts and nutn screws etcl complete within all leads and lifts as per the direction of the Engineer-In-Charge and other incidentals.

300x16mm (Three hundred into sixteen millimeters).

Providing and fixing aluminium tower bolts (barrerl type) anodized transparent or dyed to required shade and colour with necessary screws etc. complete within all leadsd and lifts as per the direction of the Engineer-In-Charge.

200x10mm 9Two hundred into ten millimeters).

100x10mm (One hundred into ten millimeteres)

Providing and fixing aliminum handles anodized transparent or dyed to required colour & shazde with necessary screws etc. complete within all leads & lifts as per the direction of Engineer-In-Charge and other incidentals.

125mm (One hundred twenty five milimeters).

100mm (One hundred millimeters).

6 mm thick (six millimetre) cement plaster to ceiling in cement mortar 1:4 ( one cement isto four sand ) upto all floors level with in all leads and lifts as per the direction of Engineer-in-Charge and other incidentials.

15 mm ( fifteen millimetre) thick cement plaster in single coat on the Rough/ fair side of brick /concrete/stone / walls for interior plastering upto floor all level including arrises internal rounded angles chamfers and or rounded angles not exceeding 80 mm ( eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 ( one cement isto six sand) upto all floor level within all leads and lifts and other incidentials.

Stone soling dry hand packed under floor including watering, ramming, consolidating and dressing complete as per HP.PWD., Specification and approved drawing and as per entire satisfaction as directed by Engineer-In Charge, including carriage of material within all leads & Lift and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:6:12 ( one cement isto six sand isto twelve broken/ crushed stone aggregate ) 40 mm (Forty millimetre) nominal size mechanical mixed and curing complete excluding the cost of form work in foundation and plinth with in all leads and lifts as per direction of Engineer- in- Charge and other incidentials.

40mm thick cement concrete flooring with 25mm under layer of cement concrete 1:3:6(1 cement :3 sand :6stone aggregate of size 12.5mm and below) and 15mm weaking layer in cement concrete 1:2 to 3(1 cement :2 to 3 stone aggregate of size 4.75 mm and below) laid integral with base course and finished with a floating coat of neat cement within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Applying Birla / J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with ready mixed paint, brushing to give an even shade including cleaning of all dirt,dust and other foreign matter,sand papering and stopping including carriage of material in all leads and lifts. : with enamel paint other than white within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Distempering (two coats) with acrylic oil bound washable distemper with Nerolac/ Asian paints of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Palove Mehra Govt Contractor